[PATCH v6 0/8] Add Type-C DP support for RK3399 EVB IND board

[PATCH v6 0/8] Add Type-C DP support for RK3399 EVB IND board

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

This series focuses on adding Type-C DP support for USBDP PHY and DP
driver. The USBDP PHY and DP will perceive the changes in cable status
based on the USB PD and Type-C state machines provided by TCPM. Before
this, the USBDP PHY and DP controller of RK3399 sensed cable state
changes through extcon, and devices such as the RK3399 Gru-Chromebook
rely on them. This series should not break them.

====
1. DisplayPort HPD status notify

Before v4, I implemented a variety of DP HPD status notify. However,
they all had various problems and it was difficult to become a common
solution.

Under Dmitry's guidance, I try to add default DRM AUX HPD device when
register DisplayPort altmode in patch 1. That makes it redundant for
each Type-C chip driver to implement a similar registration process
in embedded scenarios.

====
2. Altmode switching and orientation switching for USBDP PHY

For USB Type-C interfaces, an external Type-C controller chip assists
by detecting cable attachment, determining plug orientation, and
reporting USB PD message. The USB/DP combo PHY supports software
configurable pin mapping and DisplayPort lane assignment. Based on
these message, the combo PHY can perform both altmode switching and
orientation switching via software.

The RK3399 EVB IND board has a Type-C interface DisplayPort. It use
fusb302 chip as Type-C controller. The connection diagram is shown below:

fusb302 chip +---> USB2.0 PHY ----> DWC3 USB controller
             |
             +---> USB/DP PHY0 +--> CDN-DP controller
                               |
                               +--> DWC3 USB controller

====
3. Multiple bridge model for RK3399 CDN-DP

The RK3399 has two USB/DP combo PHY and one CDN-DP controller. And
the CDN-DP can be switched to output to one of the PHYs.

USB/DP PHY0 ---+
               | <----> CDN-DP controller
USB/DP PHY1 ---+

In previous versions, if both PHY ports were connected to DP,
the CDN-DP driver would select the first PHY port for output.

On Dmitry's suggestion, we introduced a multi-bridge model to support
flexible selection of the output PHY port. For each PHY port, a
separate encoder and bridge are registered.

The change is based on the DRM AUX HPD bridge, rather than the
extcon approach. This requires the DT to correctly describe the
connections between the first bridge in bridge chain and DP
controller. And Once the first bridge is obtained, we can get the
last bridge corresponding to the USB-C connector, and then set the
DRM connector's fwnode to the corresponding one to enable HPD
notification.

====
Patch1 add default HPD device when register Displayport altmode.
Patch2 add new Type-C mode switch for RK3399 USBDP phy binding.
Patch3 add typec_mux and typec_switch for RK3399 USBDP PHY.
Patch4 add DRM AUX bridge support for RK3399 USBDP PHY.
Patch5 drops CDN-DP's extcon dependency when Type-C is present.
Patch6 add multiple bridges to support PHY port selection. 
Patch7 add missing dp_out port for RK3399 CDN-DP.
Patch8 add Type-C DP support for RK3399 EVB IND board.

Changes in v6:
- Link to V5: https://lore.kernel.org/all/20251011033233.97-1-kernel@airkyi.com/
- Fix depend in Kconfig. 
- Check DP svid in tcphy_typec_mux_set().
- Remove mode setting in tcphy_orien_sw_set().
- Rename some variable names.
- Attach the DP bridge to the next bridge.

Changes in v5:
- Link to V4: https://lore.kernel.org/all/20250922012039.323-1-kernel@airkyi.com/
- Remove the calls related to `drm_aux_hpd_bridge_notify()`.
- Place the helper functions in the same compilation unit.
- Add more comments about parent device.
- Add DRM AUX bridge support for RK3399 USBDP PHY
- By parsing the HPD bridge chain, set the connector's of_node to the
of_node corresponding to the USB-C connector.
- Return EDID cache when other port is already enabled. 

Changes in v4:
- Link to V3: https://lore.kernel.org/all/20250729090032.97-1-kernel@airkyi.com/
- Add default HPD device for DisplayPort altmode.
- Introduce multiple bridges for CDN-DP.
- ...

Changes in v3:
- Link to V2: https://lore.kernel.org/all/20250718062619.99-1-kernel@airkyi.com/
- Add more descriptions to clarify the role of the PHY in switching.
- Fix wrong vdo value.
- Fix port node in usb-c-connector.

Changes in v2:
- Link to V1: https://lore.kernel.org/all/20250715112456.101-1-kernel@airkyi.com/
- Reuse dp-port/usb3-port in rk3399-typec-phy binding.
- Fix compile error when CONFIG_TYPEC is not enabled.
- Notify DP HPD state by USB/DP PHY.
- Ignore duplicate HPD events.
- Add endpoint to link DP PHY and DP controller.
- Fix devicetree coding style.

Chaoyi Chen (8):
  usb: typec: Add default HPD device when register DisplayPort altmode
  dt-bindings: phy: rockchip: rk3399-typec-phy: Support mode-switch
  phy: rockchip: phy-rockchip-typec: Add typec_mux/typec_switch support
  phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge
  drm/rockchip: cdn-dp: Support handle lane info without extcon
  drm/rockchip: cdn-dp: Add multiple bridges to support PHY port
    selection
  arm64: dts: rockchip: Add missing dp_out port for RK3399 CDN-DP
  arm64: dts: rockchip: rk3399-evb-ind: Add support for DisplayPort

 .../phy/rockchip,rk3399-typec-phy.yaml        |   6 +
 arch/arm64/boot/dts/rockchip/rk3399-base.dtsi |  10 +-
 .../boot/dts/rockchip/rk3399-evb-ind.dts      | 146 ++++++
 drivers/gpu/drm/rockchip/cdn-dp-core.c        | 354 ++++++++++++---
 drivers/gpu/drm/rockchip/cdn-dp-core.h        |  24 +-
 drivers/phy/rockchip/Kconfig                  |   3 +
 drivers/phy/rockchip/phy-rockchip-typec.c     | 420 +++++++++++++++++-
 drivers/usb/typec/Kconfig                     |   2 +
 drivers/usb/typec/class.c                     |  26 ++
 include/linux/usb/typec_altmode.h             |   2 +
 10 files changed, 911 insertions(+), 82 deletions(-)

-- 
2.49.0

[PATCH v6 1/8] usb: typec: Add default HPD device when register DisplayPort altmode

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

Add default DRM AUX HPD bridge device when register DisplayPort
altmode. That makes it redundant for each Type-C driver to implement
a similar registration process in embedded scenarios.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

Changes in v6:
- Fix depend in Kconfig.

Changes in v5:
- Remove the calls related to `drm_aux_hpd_bridge_notify()`.
- Place the helper functions in the same compilation unit.
- Add more comments about parent device.

 drivers/usb/typec/Kconfig         |  2 ++
 drivers/usb/typec/class.c         | 26 ++++++++++++++++++++++++++
 include/linux/usb/typec_altmode.h |  2 ++
 3 files changed, 30 insertions(+)

diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
index 2f80c2792dbd..a6730fbb576b 100644
--- a/drivers/usb/typec/Kconfig
+++ b/drivers/usb/typec/Kconfig
@@ -2,6 +2,8 @@
 
 menuconfig TYPEC
 	tristate "USB Type-C Support"
+	depends on DRM || DRM=n
+	select DRM_AUX_HPD_BRIDGE if DRM_BRIDGE && OF
 	help
 	  USB Type-C Specification defines a cable and connector for USB where
 	  only one type of plug is supported on both ends, i.e. there will not
diff --git a/drivers/usb/typec/class.c b/drivers/usb/typec/class.c
index 67a533e35150..e9d7772d1a8f 100644
--- a/drivers/usb/typec/class.c
+++ b/drivers/usb/typec/class.c
@@ -8,14 +8,18 @@
 
 #include <linux/module.h>
 #include <linux/mutex.h>
+#include <linux/of.h>
 #include <linux/property.h>
 #include <linux/slab.h>
 #include <linux/string_choices.h>
 #include <linux/usb/pd_vdo.h>
+#include <linux/usb/typec_dp.h>
 #include <linux/usb/typec_mux.h>
 #include <linux/usb/typec_retimer.h>
 #include <linux/usb.h>
 
+#include <drm/bridge/aux-bridge.h>
+
 #include "bus.h"
 #include "class.h"
 #include "pd.h"
@@ -538,6 +542,21 @@ const struct device_type typec_altmode_dev_type = {
 	.release = typec_altmode_release,
 };
 
+static void dp_altmode_hpd_device_register(struct typec_altmode *alt)
+{
+	if (alt->svid != USB_TYPEC_DP_SID)
+		return;
+
+	/*
+	 * alt->dev.parent->parent : USB-C controller device
+	 * alt->dev.parent         : USB-C connector device
+	 */
+	alt->hpd_dev = drm_dp_hpd_bridge_register(alt->dev.parent->parent,
+						  to_of_node(alt->dev.parent->fwnode));
+	if (IS_ERR(alt->hpd_dev))
+		alt->hpd_dev = NULL;
+}
+
 static struct typec_altmode *
 typec_register_altmode(struct device *parent,
 		       const struct typec_altmode_desc *desc)
@@ -600,6 +619,13 @@ typec_register_altmode(struct device *parent,
 		return ERR_PTR(ret);
 	}
 
+	/*
+	 * It is too late to register the HPD device when the DisplayPort
+	 * altmode device becomes ready. If the current altmode is DP,
+	 * register a static HPD device.
+	 */
+	dp_altmode_hpd_device_register(&alt->adev);
+
 	return &alt->adev;
 }
 
diff --git a/include/linux/usb/typec_altmode.h b/include/linux/usb/typec_altmode.h
index b3c0866ea70f..acb0af1b9d5d 100644
--- a/include/linux/usb/typec_altmode.h
+++ b/include/linux/usb/typec_altmode.h
@@ -21,6 +21,7 @@ struct typec_altmode_ops;
  * @desc: Optional human readable description of the mode
  * @ops: Operations vector from the driver
  * @cable_ops: Cable operations vector from the driver.
+ * @hpd_dev: HPD device for DisplayPort
  */
 struct typec_altmode {
 	struct device			dev;
@@ -32,6 +33,7 @@ struct typec_altmode {
 	char				*desc;
 	const struct typec_altmode_ops	*ops;
 	const struct typec_cable_ops	*cable_ops;
+	struct device			*hpd_dev;
 };
 
 #define to_typec_altmode(d) container_of(d, struct typec_altmode, dev)
-- 
2.49.0

Re: [PATCH v6 1/8] usb: typec: Add default HPD device when register DisplayPort altmode

[Heikki Krogerus]

On Thu, Oct 16, 2025 at 10:27:34AM +0800, Chaoyi Chen wrote:
> From: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> 
> Add default DRM AUX HPD bridge device when register DisplayPort
> altmode. That makes it redundant for each Type-C driver to implement
> a similar registration process in embedded scenarios.
> 
> Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> ---
> 
> Changes in v6:
> - Fix depend in Kconfig.
> 
> Changes in v5:
> - Remove the calls related to `drm_aux_hpd_bridge_notify()`.
> - Place the helper functions in the same compilation unit.
> - Add more comments about parent device.
> 
>  drivers/usb/typec/Kconfig         |  2 ++
>  drivers/usb/typec/class.c         | 26 ++++++++++++++++++++++++++
>  include/linux/usb/typec_altmode.h |  2 ++
>  3 files changed, 30 insertions(+)
> 
> diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
> index 2f80c2792dbd..a6730fbb576b 100644
> --- a/drivers/usb/typec/Kconfig
> +++ b/drivers/usb/typec/Kconfig
> @@ -2,6 +2,8 @@
>  
>  menuconfig TYPEC
>  	tristate "USB Type-C Support"
> +	depends on DRM || DRM=n
> +	select DRM_AUX_HPD_BRIDGE if DRM_BRIDGE && OF

This is wrong. DRM should not dictate how this entire subsystem core
is configured. The dependency needs to be on the DRM bridge side.

You can for example use the bus notification there to see when a new
alternate mode is being registered, or use some other notification
mechanism.

thanks,

>  	help
>  	  USB Type-C Specification defines a cable and connector for USB where
>  	  only one type of plug is supported on both ends, i.e. there will not
> diff --git a/drivers/usb/typec/class.c b/drivers/usb/typec/class.c
> index 67a533e35150..e9d7772d1a8f 100644
> --- a/drivers/usb/typec/class.c
> +++ b/drivers/usb/typec/class.c
> @@ -8,14 +8,18 @@
>  
>  #include <linux/module.h>
>  #include <linux/mutex.h>
> +#include <linux/of.h>
>  #include <linux/property.h>
>  #include <linux/slab.h>
>  #include <linux/string_choices.h>
>  #include <linux/usb/pd_vdo.h>
> +#include <linux/usb/typec_dp.h>
>  #include <linux/usb/typec_mux.h>
>  #include <linux/usb/typec_retimer.h>
>  #include <linux/usb.h>
>  
> +#include <drm/bridge/aux-bridge.h>
> +
>  #include "bus.h"
>  #include "class.h"
>  #include "pd.h"
> @@ -538,6 +542,21 @@ const struct device_type typec_altmode_dev_type = {
>  	.release = typec_altmode_release,
>  };
>  
> +static void dp_altmode_hpd_device_register(struct typec_altmode *alt)
> +{
> +	if (alt->svid != USB_TYPEC_DP_SID)
> +		return;
> +
> +	/*
> +	 * alt->dev.parent->parent : USB-C controller device
> +	 * alt->dev.parent         : USB-C connector device
> +	 */
> +	alt->hpd_dev = drm_dp_hpd_bridge_register(alt->dev.parent->parent,
> +						  to_of_node(alt->dev.parent->fwnode));
> +	if (IS_ERR(alt->hpd_dev))
> +		alt->hpd_dev = NULL;
> +}
> +
>  static struct typec_altmode *
>  typec_register_altmode(struct device *parent,
>  		       const struct typec_altmode_desc *desc)
> @@ -600,6 +619,13 @@ typec_register_altmode(struct device *parent,
>  		return ERR_PTR(ret);
>  	}
>  
> +	/*
> +	 * It is too late to register the HPD device when the DisplayPort
> +	 * altmode device becomes ready. If the current altmode is DP,
> +	 * register a static HPD device.
> +	 */
> +	dp_altmode_hpd_device_register(&alt->adev);
> +
>  	return &alt->adev;
>  }
>  
> diff --git a/include/linux/usb/typec_altmode.h b/include/linux/usb/typec_altmode.h
> index b3c0866ea70f..acb0af1b9d5d 100644
> --- a/include/linux/usb/typec_altmode.h
> +++ b/include/linux/usb/typec_altmode.h
> @@ -21,6 +21,7 @@ struct typec_altmode_ops;
>   * @desc: Optional human readable description of the mode
>   * @ops: Operations vector from the driver
>   * @cable_ops: Cable operations vector from the driver.
> + * @hpd_dev: HPD device for DisplayPort
>   */
>  struct typec_altmode {
>  	struct device			dev;
> @@ -32,6 +33,7 @@ struct typec_altmode {
>  	char				*desc;
>  	const struct typec_altmode_ops	*ops;
>  	const struct typec_cable_ops	*cable_ops;
> +	struct device			*hpd_dev;
>  };
>  
>  #define to_typec_altmode(d) container_of(d, struct typec_altmode, dev)
> -- 
> 2.49.0

-- 
heikki

Re: [PATCH v6 1/8] usb: typec: Add default HPD device when register DisplayPort altmode

[Chaoyi Chen]

Hi Heikki,

On 10/20/2025 6:02 PM, Heikki Krogerus wrote:
> On Thu, Oct 16, 2025 at 10:27:34AM +0800, Chaoyi Chen wrote:
>> From: Chaoyi Chen <chaoyi.chen@rock-chips.com>
>>
>> Add default DRM AUX HPD bridge device when register DisplayPort
>> altmode. That makes it redundant for each Type-C driver to implement
>> a similar registration process in embedded scenarios.
>>
>> Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
>> ---
>>
>> Changes in v6:
>> - Fix depend in Kconfig.
>>
>> Changes in v5:
>> - Remove the calls related to `drm_aux_hpd_bridge_notify()`.
>> - Place the helper functions in the same compilation unit.
>> - Add more comments about parent device.
>>
>>   drivers/usb/typec/Kconfig         |  2 ++
>>   drivers/usb/typec/class.c         | 26 ++++++++++++++++++++++++++
>>   include/linux/usb/typec_altmode.h |  2 ++
>>   3 files changed, 30 insertions(+)
>>
>> diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
>> index 2f80c2792dbd..a6730fbb576b 100644
>> --- a/drivers/usb/typec/Kconfig
>> +++ b/drivers/usb/typec/Kconfig
>> @@ -2,6 +2,8 @@
>>   
>>   menuconfig TYPEC
>>   	tristate "USB Type-C Support"
>> +	depends on DRM || DRM=n
>> +	select DRM_AUX_HPD_BRIDGE if DRM_BRIDGE && OF
> This is wrong. DRM should not dictate how this entire subsystem core
> is configured. The dependency needs to be on the DRM bridge side.
>
> You can for example use the bus notification there to see when a new
> alternate mode is being registered, or use some other notification
> mechanism.

Is it a good idea to implement notification functions like drivers/usb/core/notify.c in TCPM, and then let other subsystems (such as DRM) listen to these notifications?


>
> thanks,
>
>>   	help
>>   	  USB Type-C Specification defines a cable and connector for USB where
>>   	  only one type of plug is supported on both ends, i.e. there will not
>> diff --git a/drivers/usb/typec/class.c b/drivers/usb/typec/class.c
>> index 67a533e35150..e9d7772d1a8f 100644
>> --- a/drivers/usb/typec/class.c
>> +++ b/drivers/usb/typec/class.c
>> @@ -8,14 +8,18 @@
>>   
>>   #include <linux/module.h>
>>   #include <linux/mutex.h>
>> +#include <linux/of.h>
>>   #include <linux/property.h>
>>   #include <linux/slab.h>
>>   #include <linux/string_choices.h>
>>   #include <linux/usb/pd_vdo.h>
>> +#include <linux/usb/typec_dp.h>
>>   #include <linux/usb/typec_mux.h>
>>   #include <linux/usb/typec_retimer.h>
>>   #include <linux/usb.h>
>>   
>> +#include <drm/bridge/aux-bridge.h>
>> +
>>   #include "bus.h"
>>   #include "class.h"
>>   #include "pd.h"
>> @@ -538,6 +542,21 @@ const struct device_type typec_altmode_dev_type = {
>>   	.release = typec_altmode_release,
>>   };
>>   
>> +static void dp_altmode_hpd_device_register(struct typec_altmode *alt)
>> +{
>> +	if (alt->svid != USB_TYPEC_DP_SID)
>> +		return;
>> +
>> +	/*
>> +	 * alt->dev.parent->parent : USB-C controller device
>> +	 * alt->dev.parent         : USB-C connector device
>> +	 */
>> +	alt->hpd_dev = drm_dp_hpd_bridge_register(alt->dev.parent->parent,
>> +						  to_of_node(alt->dev.parent->fwnode));
>> +	if (IS_ERR(alt->hpd_dev))
>> +		alt->hpd_dev = NULL;
>> +}
>> +
>>   static struct typec_altmode *
>>   typec_register_altmode(struct device *parent,
>>   		       const struct typec_altmode_desc *desc)
>> @@ -600,6 +619,13 @@ typec_register_altmode(struct device *parent,
>>   		return ERR_PTR(ret);
>>   	}
>>   
>> +	/*
>> +	 * It is too late to register the HPD device when the DisplayPort
>> +	 * altmode device becomes ready. If the current altmode is DP,
>> +	 * register a static HPD device.
>> +	 */
>> +	dp_altmode_hpd_device_register(&alt->adev);
>> +
>>   	return &alt->adev;
>>   }
>>   
>> diff --git a/include/linux/usb/typec_altmode.h b/include/linux/usb/typec_altmode.h
>> index b3c0866ea70f..acb0af1b9d5d 100644
>> --- a/include/linux/usb/typec_altmode.h
>> +++ b/include/linux/usb/typec_altmode.h
>> @@ -21,6 +21,7 @@ struct typec_altmode_ops;
>>    * @desc: Optional human readable description of the mode
>>    * @ops: Operations vector from the driver
>>    * @cable_ops: Cable operations vector from the driver.
>> + * @hpd_dev: HPD device for DisplayPort
>>    */
>>   struct typec_altmode {
>>   	struct device			dev;
>> @@ -32,6 +33,7 @@ struct typec_altmode {
>>   	char				*desc;
>>   	const struct typec_altmode_ops	*ops;
>>   	const struct typec_cable_ops	*cable_ops;
>> +	struct device			*hpd_dev;
>>   };
>>   
>>   #define to_typec_altmode(d) container_of(d, struct typec_altmode, dev)
>> -- 
>> 2.49.0

-- 
Best,
Chaoyi

Re: [PATCH v6 1/8] usb: typec: Add default HPD device when register DisplayPort altmode

[Heikki Krogerus]

Hi,

On Mon, Oct 20, 2025 at 07:07:46PM +0800, Chaoyi Chen wrote:
> Hi Heikki,
> 
> On 10/20/2025 6:02 PM, Heikki Krogerus wrote:
> > On Thu, Oct 16, 2025 at 10:27:34AM +0800, Chaoyi Chen wrote:
> > > From: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> > > 
> > > Add default DRM AUX HPD bridge device when register DisplayPort
> > > altmode. That makes it redundant for each Type-C driver to implement
> > > a similar registration process in embedded scenarios.
> > > 
> > > Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> > > ---
> > > 
> > > Changes in v6:
> > > - Fix depend in Kconfig.
> > > 
> > > Changes in v5:
> > > - Remove the calls related to `drm_aux_hpd_bridge_notify()`.
> > > - Place the helper functions in the same compilation unit.
> > > - Add more comments about parent device.
> > > 
> > >   drivers/usb/typec/Kconfig         |  2 ++
> > >   drivers/usb/typec/class.c         | 26 ++++++++++++++++++++++++++
> > >   include/linux/usb/typec_altmode.h |  2 ++
> > >   3 files changed, 30 insertions(+)
> > > 
> > > diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
> > > index 2f80c2792dbd..a6730fbb576b 100644
> > > --- a/drivers/usb/typec/Kconfig
> > > +++ b/drivers/usb/typec/Kconfig
> > > @@ -2,6 +2,8 @@
> > >   menuconfig TYPEC
> > >   	tristate "USB Type-C Support"
> > > +	depends on DRM || DRM=n
> > > +	select DRM_AUX_HPD_BRIDGE if DRM_BRIDGE && OF
> > This is wrong. DRM should not dictate how this entire subsystem core
> > is configured. The dependency needs to be on the DRM bridge side.
> > 
> > You can for example use the bus notification there to see when a new
> > alternate mode is being registered, or use some other notification
> > mechanism.
> 
> Is it a good idea to implement notification functions like
> drivers/usb/core/notify.c in TCPM, and then let other subsystems (such as DRM)
> listen to these notifications?

Don't limit this to tcpm only. I would suggest something similar what
we have for usb bus: drivers/usb/core/notify.c

So that, but for the typec bus. Then in DRM bridge code you just use
typec_register/unregister_notify().

thanks,

-- 
heikki

Re: [PATCH v6 1/8] usb: typec: Add default HPD device when register DisplayPort altmode

[Chaoyi Chen]

On 10/21/2025 4:48 PM, Heikki Krogerus wrote:

> Hi,
>
> On Mon, Oct 20, 2025 at 07:07:46PM +0800, Chaoyi Chen wrote:
>> Hi Heikki,
>>
>> On 10/20/2025 6:02 PM, Heikki Krogerus wrote:
>>> On Thu, Oct 16, 2025 at 10:27:34AM +0800, Chaoyi Chen wrote:
>>>> From: Chaoyi Chen <chaoyi.chen@rock-chips.com>
>>>>
>>>> Add default DRM AUX HPD bridge device when register DisplayPort
>>>> altmode. That makes it redundant for each Type-C driver to implement
>>>> a similar registration process in embedded scenarios.
>>>>
>>>> Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
>>>> ---
>>>>
>>>> Changes in v6:
>>>> - Fix depend in Kconfig.
>>>>
>>>> Changes in v5:
>>>> - Remove the calls related to `drm_aux_hpd_bridge_notify()`.
>>>> - Place the helper functions in the same compilation unit.
>>>> - Add more comments about parent device.
>>>>
>>>>    drivers/usb/typec/Kconfig         |  2 ++
>>>>    drivers/usb/typec/class.c         | 26 ++++++++++++++++++++++++++
>>>>    include/linux/usb/typec_altmode.h |  2 ++
>>>>    3 files changed, 30 insertions(+)
>>>>
>>>> diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
>>>> index 2f80c2792dbd..a6730fbb576b 100644
>>>> --- a/drivers/usb/typec/Kconfig
>>>> +++ b/drivers/usb/typec/Kconfig
>>>> @@ -2,6 +2,8 @@
>>>>    menuconfig TYPEC
>>>>    	tristate "USB Type-C Support"
>>>> +	depends on DRM || DRM=n
>>>> +	select DRM_AUX_HPD_BRIDGE if DRM_BRIDGE && OF
>>> This is wrong. DRM should not dictate how this entire subsystem core
>>> is configured. The dependency needs to be on the DRM bridge side.
>>>
>>> You can for example use the bus notification there to see when a new
>>> alternate mode is being registered, or use some other notification
>>> mechanism.
>> Is it a good idea to implement notification functions like
>> drivers/usb/core/notify.c in TCPM, and then let other subsystems (such as DRM)
>> listen to these notifications?
> Don't limit this to tcpm only. I would suggest something similar what
> we have for usb bus: drivers/usb/core/notify.c
>
> So that, but for the typec bus. Then in DRM bridge code you just use
> typec_register/unregister_notify().

I will try to add drivers/usb/typec/notify.c in v7 to implement this. Thank you.


>
> thanks,
>
-- 
Best,
Chaoyi

[PATCH v6 2/8] dt-bindings: phy: rockchip: rk3399-typec-phy: Support mode-switch

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

The RK3399 SoC integrates two USB/DP combo PHYs, each of which
supports software-configurable pin mapping and DisplayPort lane
assignment. These capabilities enable the PHY itself to handle both
mode switching and orientation switching, based on the Type-C plug
orientation and USB PD negotiation results.

While an external Type-C controller is still required to detect cable
attachment and report USB PD events, the actual mode and orientation
switching is performed internally by the PHY through software
configuration. This allows the PHY to act as a Type-C multiplexer for
both data role and DP altmode configuration.

To reflect this hardware design, this patch introduces a new
"mode-switch" property for the dp-port node in the device tree bindings.
This property indicates that the connected PHY is capable of handling
Type-C mode switching itself.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---

(no changes since v5)

Changes in v4:
- Remove "|" in description.

Changes in v3:
- Add more descriptions to clarify the role of the PHY in switching.

Changes in v2:
- Reuse dp-port/usb3-port in rk3399-typec-phy binding.

 .../devicetree/bindings/phy/rockchip,rk3399-typec-phy.yaml  | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/rockchip,rk3399-typec-phy.yaml b/Documentation/devicetree/bindings/phy/rockchip,rk3399-typec-phy.yaml
index 91c011f68cd0..83ebcde096ea 100644
--- a/Documentation/devicetree/bindings/phy/rockchip,rk3399-typec-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/rockchip,rk3399-typec-phy.yaml
@@ -51,6 +51,12 @@ properties:
       '#phy-cells':
         const: 0
 
+      mode-switch:
+        description:
+          Indicates the PHY can handle altmode switching. In this case,
+          requires an external USB Type-C controller to report USB PD message.
+        type: boolean
+
       port:
         $ref: /schemas/graph.yaml#/properties/port
         description: Connection to USB Type-C connector
-- 
2.49.0

[PATCH v6 3/8] phy: rockchip: phy-rockchip-typec: Add typec_mux/typec_switch support

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

This patch add support for Type-C Port Controller Manager. Each PHY
will register typec_mux and typec_switch when external Type-C
controller is present. Type-C events are handled by TCPM without
extcon.

The extcon device should still be supported.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

Changes in v6:
- Fix depend in Kconfig.
- Check DP svid in tcphy_typec_mux_set().
- Remove mode setting in tcphy_orien_sw_set().

(no changes since v5)

Changes in v4:
- Remove notify DP HPD state by USB/DP PHY.

(no changes since v3)

Changes in v2:
- Fix compile error when CONFIG_TYPEC is not enabled.
- Notify DP HPD state by USB/DP PHY.

 drivers/phy/rockchip/Kconfig              |   1 +
 drivers/phy/rockchip/phy-rockchip-typec.c | 368 +++++++++++++++++++++-
 2 files changed, 353 insertions(+), 16 deletions(-)

diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
index 14698571b607..db4adc7c53da 100644
--- a/drivers/phy/rockchip/Kconfig
+++ b/drivers/phy/rockchip/Kconfig
@@ -119,6 +119,7 @@ config PHY_ROCKCHIP_SNPS_PCIE3
 config PHY_ROCKCHIP_TYPEC
 	tristate "Rockchip TYPEC PHY Driver"
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
+	depends on TYPEC || TYPEC=n
 	select EXTCON
 	select GENERIC_PHY
 	select RESET_CONTROLLER
diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
index d9701b6106d5..1f5b4142cbe4 100644
--- a/drivers/phy/rockchip/phy-rockchip-typec.c
+++ b/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -54,6 +54,8 @@
 
 #include <linux/mfd/syscon.h>
 #include <linux/phy/phy.h>
+#include <linux/usb/typec_dp.h>
+#include <linux/usb/typec_mux.h>
 
 #define CMN_SSM_BANDGAP			(0x21 << 2)
 #define CMN_SSM_BIAS			(0x22 << 2)
@@ -286,12 +288,23 @@
 #define RX_DIAG_SC2C_DELAY		(0x81e1 << 2)
 
 #define PMA_LANE_CFG			(0xc000 << 2)
+#define PMA_LANE3_DP_LANE_SEL(x)	(((x) & 0x3) << 14)
+#define PMA_LANE3_INTERFACE_SEL(x)	(((x) & 0x1) << 12)
+#define PMA_LANE2_DP_LANE_SEL(x)	(((x) & 0x3) << 10)
+#define PMA_LANE2_INTERFACE_SEL(x)	(((x) & 0x1) << 8)
+#define PMA_LANE1_DP_LANE_SEL(x)	(((x) & 0x3) << 6)
+#define PMA_LANE1_INTERFACE_SEL(x)	(((x) & 0x1) << 4)
+#define PMA_LANE0_DP_LANE_SEL(x)	(((x) & 0x3) << 2)
+#define PMA_LANE0_INTERFACE_SEL(x)	(((x) & 0x1) << 0)
 #define PIPE_CMN_CTRL1			(0xc001 << 2)
 #define PIPE_CMN_CTRL2			(0xc002 << 2)
 #define PIPE_COM_LOCK_CFG1		(0xc003 << 2)
 #define PIPE_COM_LOCK_CFG2		(0xc004 << 2)
 #define PIPE_RCV_DET_INH		(0xc005 << 2)
 #define DP_MODE_CTL			(0xc008 << 2)
+#define PHY_DP_POWER_STATE_ACK_MASK	GENMASK(7, 4)
+#define PHY_DP_POWER_STATE_ACK_SHIFT	4
+#define PHY_DP_POWER_STATE_MASK		GENMASK(3, 0)
 #define DP_CLK_CTL			(0xc009 << 2)
 #define STS				(0xc00F << 2)
 #define PHY_ISO_CMN_CTRL		(0xc010 << 2)
@@ -327,8 +340,15 @@
 
 #define DP_MODE_A0			BIT(4)
 #define DP_MODE_A2			BIT(6)
-#define DP_MODE_ENTER_A0		0xc101
-#define DP_MODE_ENTER_A2		0xc104
+
+#define DP_MODE_MASK			0xf
+#define DP_MODE_ENTER_A0		BIT(0)
+#define DP_MODE_ENTER_A2		BIT(2)
+#define DP_MODE_ENTER_A3		BIT(3)
+#define DP_MODE_A0_ACK			BIT(4)
+#define DP_MODE_A2_ACK			BIT(6)
+#define DP_MODE_A3_ACK			BIT(7)
+#define DP_LINK_RESET_DEASSERTED	BIT(8)
 
 #define PHY_MODE_SET_TIMEOUT		100000
 
@@ -340,6 +360,31 @@
 #define MODE_DFP_USB			BIT(1)
 #define MODE_DFP_DP			BIT(2)
 
+enum phy_dp_lane_num {
+	PHY_DP_LANE_0 = 0,
+	PHY_DP_LANE_1,
+	PHY_DP_LANE_2,
+	PHY_DP_LANE_3,
+};
+
+enum phy_pma_if {
+	PMA_IF_PIPE_PCS = 0,
+	PMA_IF_PHY_DP,
+};
+
+enum phy_typec_role {
+	TYPEC_PHY_USB = 0,
+	TYPEC_PHY_DP,
+	TYPEC_PHY_MAX,
+};
+
+enum phy_dp_power_state {
+	PHY_DP_POWER_STATE_A0 = 0,
+	PHY_DP_POWER_STATE_A1,
+	PHY_DP_POWER_STATE_A2,
+	PHY_DP_POWER_STATE_A3,
+};
+
 struct usb3phy_reg {
 	u32 offset;
 	u32 enable_bit;
@@ -372,18 +417,22 @@ struct rockchip_typec_phy {
 	struct device *dev;
 	void __iomem *base;
 	struct extcon_dev *extcon;
+	struct typec_mux_dev *mux;
+	struct typec_switch_dev *sw;
 	struct regmap *grf_regs;
 	struct clk *clk_core;
 	struct clk *clk_ref;
 	struct reset_control *uphy_rst;
 	struct reset_control *pipe_rst;
 	struct reset_control *tcphy_rst;
+	struct phy *phys[TYPEC_PHY_MAX];
 	const struct rockchip_usb3phy_port_cfg *port_cfgs;
 	/* mutex to protect access to individual PHYs */
 	struct mutex lock;
 
 	bool flip;
 	u8 mode;
+	u8 new_mode;
 };
 
 struct phy_reg {
@@ -454,6 +503,99 @@ static const struct rockchip_usb3phy_port_cfg rk3399_usb3phy_port_cfgs[] = {
 	{ /* sentinel */ }
 };
 
+static int tcphy_cfg_usb3_to_usb2_only(struct rockchip_typec_phy *tcphy,
+				       bool value);
+
+static int tcphy_dp_set_power_state(struct rockchip_typec_phy *tcphy,
+				    enum phy_dp_power_state state)
+{
+	u32 ack, reg, sts = BIT(state);
+	int ret;
+
+	/*
+	 * Power state changes must not be requested until after the cmn_ready
+	 * signal has gone active.
+	 */
+	reg = readl(tcphy->base + PMA_CMN_CTRL1);
+	if (!(reg & CMN_READY)) {
+		dev_err(tcphy->dev, "cmn_ready in the inactive state\n");
+		return -EINVAL;
+	}
+
+	reg = readl(tcphy->base + DP_MODE_CTL);
+	reg &= ~PHY_DP_POWER_STATE_MASK;
+	reg |= sts;
+	writel(reg, tcphy->base + DP_MODE_CTL);
+
+	ret = readl_poll_timeout(tcphy->base + DP_MODE_CTL,
+				 ack, (((ack & PHY_DP_POWER_STATE_ACK_MASK) >>
+				 PHY_DP_POWER_STATE_ACK_SHIFT) == sts), 10,
+				 PHY_MODE_SET_TIMEOUT);
+	if (ret < 0) {
+		dev_err(tcphy->dev, "failed to enter power state %d\n", state);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * For the TypeC PHY, the 4 lanes are mapping to the USB TypeC receptacle pins
+ * as follows:
+ *   -------------------------------------------------------------------
+ *	PHY Lanes/Module Pins			TypeC Receptacle Pins
+ *   -------------------------------------------------------------------
+ *	Lane0 (tx_p/m_ln_0)			TX1+/TX1- (pins A2/A3)
+ *	Lane1 (tx_rx_p/m_ln_1)			RX1+/RX1- (pins B11/B10)
+ *	Lane2 (tx_rx_p/m_ln_2)			RX2+/RX2- (pins A11/A10)
+ *	Lane3 (tx_p/m_ln_3)			TX2+/TX2- (pins B2/B3)
+ *   -------------------------------------------------------------------
+ *
+ * USB and DP lanes mapping to TypeC PHY lanes for each of pin assignment
+ * options (normal connector orientation) described in the VESA DisplayPort
+ * Alt Mode on USB TypeC Standard as follows:
+ *
+ * ----------------------------------------------------------------------
+ *	PHY Lanes	A	B	C	D	E	F
+ * ----------------------------------------------------------------------
+ *	  0	       ML1     SSTX    ML2     SSTX    ML2     SSTX
+ *	  1	       ML3     SSRX    ML3     SSRX    ML3     SSRX
+ *	  2	       ML2     ML1     ML0     ML0     ML0     ML0
+ *	  3	       ML0     ML0     ML1     ML1     ML1     ML1
+ * ----------------------------------------------------------------------
+ */
+static void tcphy_set_lane_mapping(struct rockchip_typec_phy *tcphy, u8 mode)
+{
+	/*
+	 * The PMA_LANE_CFG register is used to select whether a PMA lane
+	 * is mapped for USB or PHY DP. The PMA_LANE_CFG register is
+	 * configured based on a normal connector orientation. Logic in the
+	 * PHY automatically handles the flipped connector case based on the
+	 * setting of orientation of TypeC PHY.
+	 */
+	if (mode == MODE_DFP_DP) {
+		/* This maps to VESA DP Alt Mode pin assignments C and E. */
+		writel(PMA_LANE3_DP_LANE_SEL(PHY_DP_LANE_1) |
+		       PMA_LANE3_INTERFACE_SEL(PMA_IF_PHY_DP) |
+		       PMA_LANE2_DP_LANE_SEL(PHY_DP_LANE_0) |
+		       PMA_LANE2_INTERFACE_SEL(PMA_IF_PHY_DP) |
+		       PMA_LANE1_DP_LANE_SEL(PHY_DP_LANE_3) |
+		       PMA_LANE1_INTERFACE_SEL(PMA_IF_PHY_DP) |
+		       PMA_LANE0_DP_LANE_SEL(PHY_DP_LANE_2) |
+		       PMA_LANE0_INTERFACE_SEL(PMA_IF_PHY_DP),
+		       tcphy->base + PMA_LANE_CFG);
+	} else {
+		/* This maps to VESA DP Alt Mode pin assignments D and F. */
+		writel(PMA_LANE3_DP_LANE_SEL(PHY_DP_LANE_1) |
+		       PMA_LANE3_INTERFACE_SEL(PMA_IF_PHY_DP) |
+		       PMA_LANE2_DP_LANE_SEL(PHY_DP_LANE_0) |
+		       PMA_LANE2_INTERFACE_SEL(PMA_IF_PHY_DP) |
+		       PMA_LANE1_INTERFACE_SEL(PMA_IF_PIPE_PCS) |
+		       PMA_LANE0_INTERFACE_SEL(PMA_IF_PIPE_PCS),
+		       tcphy->base + PMA_LANE_CFG);
+	}
+}
+
 static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
 {
 	u32 i, rdata;
@@ -743,8 +885,10 @@ static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
 	tcphy_dp_aux_set_flip(tcphy);
 
 	tcphy_cfg_24m(tcphy);
+	tcphy_set_lane_mapping(tcphy, mode);
 
 	if (mode == MODE_DFP_DP) {
+		tcphy_cfg_usb3_to_usb2_only(tcphy, true);
 		tcphy_cfg_dp_pll(tcphy);
 		for (i = 0; i < 4; i++)
 			tcphy_dp_cfg_lane(tcphy, i);
@@ -768,7 +912,10 @@ static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
 		writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG);
 	}
 
-	writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+	val = readl(tcphy->base + DP_MODE_CTL);
+	val &= ~DP_MODE_MASK;
+	val |= DP_MODE_ENTER_A2 | DP_LINK_RESET_DEASSERTED;
+	writel(val, tcphy->base + DP_MODE_CTL);
 
 	reset_control_deassert(tcphy->uphy_rst);
 
@@ -811,8 +958,9 @@ static int tcphy_get_mode(struct rockchip_typec_phy *tcphy)
 	u8 mode;
 	int ret, ufp, dp;
 
+	/* If extcon not exist, try to use tcpm mode */
 	if (!edev)
-		return MODE_DFP_USB;
+		return tcphy->new_mode;
 
 	ufp = extcon_get_state(edev, EXTCON_USB);
 	dp = extcon_get_state(edev, EXTCON_DISP_DP);
@@ -850,6 +998,71 @@ static int tcphy_get_mode(struct rockchip_typec_phy *tcphy)
 	return mode;
 }
 
+#if IS_ENABLED(CONFIG_TYPEC)
+static int tcphy_orien_sw_set(struct typec_switch_dev *sw,
+			      enum typec_orientation orien)
+{
+	struct rockchip_typec_phy *tcphy = typec_switch_get_drvdata(sw);
+
+	mutex_lock(&tcphy->lock);
+
+	if (orien == TYPEC_ORIENTATION_NONE) {
+		tcphy->new_mode = MODE_DISCONNECT;
+		goto unlock_ret;
+	}
+
+	tcphy->flip = (orien == TYPEC_ORIENTATION_REVERSE) ? true : false;
+
+unlock_ret:
+	mutex_unlock(&tcphy->lock);
+	return 0;
+}
+
+static void udphy_orien_switch_unregister(void *data)
+{
+	struct rockchip_typec_phy *tcphy = data;
+
+	typec_switch_unregister(tcphy->sw);
+}
+
+static int tcphy_setup_orien_switch(struct rockchip_typec_phy *tcphy)
+{
+	struct typec_switch_desc sw_desc = { };
+	struct device_node *np;
+	int ret = 0;
+
+	np = of_get_child_by_name(tcphy->dev->of_node, "usb3-port");
+	if (!np)
+		return 0;
+
+	if (!of_property_read_bool(np, "orientation-switch"))
+		goto put_np;
+
+	sw_desc.drvdata = tcphy;
+	sw_desc.fwnode = device_get_named_child_node(tcphy->dev, "usb3-port");
+	sw_desc.set = tcphy_orien_sw_set;
+
+	tcphy->sw = typec_switch_register(tcphy->dev, &sw_desc);
+	if (IS_ERR(tcphy->sw)) {
+		dev_err(tcphy->dev, "Error register typec orientation switch: %ld\n",
+			PTR_ERR(tcphy->sw));
+		ret = PTR_ERR(tcphy->sw);
+		goto put_np;
+	}
+
+	ret = devm_add_action_or_reset(tcphy->dev, udphy_orien_switch_unregister, tcphy);
+
+put_np:
+	of_node_put(np);
+	return ret;
+}
+#else
+static int tcphy_setup_orien_switch(struct rockchip_typec_phy *tcphy)
+{
+	return 0;
+}
+#endif
+
 static int tcphy_cfg_usb3_to_usb2_only(struct rockchip_typec_phy *tcphy,
 				       bool value)
 {
@@ -989,14 +1202,9 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
 
 	tcphy_dp_aux_calibration(tcphy);
 
-	writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL);
-
-	ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
-				 val, val & DP_MODE_A0, 1000,
-				 PHY_MODE_SET_TIMEOUT);
-	if (ret < 0) {
-		writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
-		dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n");
+	ret = tcphy_dp_set_power_state(tcphy, PHY_DP_POWER_STATE_A0);
+	if (ret) {
+		dev_err(tcphy->dev, "failed to enter A0 power state\n");
 		goto power_on_finish;
 	}
 
@@ -1013,6 +1221,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
 static int rockchip_dp_phy_power_off(struct phy *phy)
 {
 	struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+	int ret;
 
 	mutex_lock(&tcphy->lock);
 
@@ -1021,7 +1230,11 @@ static int rockchip_dp_phy_power_off(struct phy *phy)
 
 	tcphy->mode &= ~MODE_DFP_DP;
 
-	writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+	ret = tcphy_dp_set_power_state(tcphy, PHY_DP_POWER_STATE_A2);
+	if (ret) {
+		dev_err(tcphy->dev, "failed to enter A2 power state\n");
+		goto unlock;
+	}
 
 	if (tcphy->mode == MODE_DISCONNECT)
 		tcphy_phy_deinit(tcphy);
@@ -1037,6 +1250,93 @@ static const struct phy_ops rockchip_dp_phy_ops = {
 	.owner		= THIS_MODULE,
 };
 
+#if IS_ENABLED(CONFIG_TYPEC)
+static int tcphy_typec_mux_set(struct typec_mux_dev *mux, struct typec_mux_state *state)
+{
+	struct rockchip_typec_phy *tcphy = typec_mux_get_drvdata(mux);
+	struct typec_displayport_data *data;
+	int hpd = 0;
+
+	mutex_lock(&tcphy->lock);
+
+	switch (state->mode) {
+	case TYPEC_STATE_SAFE:
+		fallthrough;
+	case TYPEC_STATE_USB:
+		tcphy->new_mode = MODE_DFP_USB;
+		phy_set_bus_width(tcphy->phys[TYPEC_PHY_DP], 0);
+		break;
+	case TYPEC_DP_STATE_C:
+	case TYPEC_DP_STATE_E:
+		if (state->alt->svid != USB_TYPEC_DP_SID)
+			break;
+		tcphy->new_mode = MODE_DFP_DP;
+		data = state->data;
+		hpd = !!(data->status & DP_STATUS_HPD_STATE);
+		phy_set_bus_width(tcphy->phys[TYPEC_PHY_DP], hpd ? 4 : 0);
+		break;
+	case TYPEC_DP_STATE_D:
+		if (state->alt->svid != USB_TYPEC_DP_SID)
+			break;
+		tcphy->new_mode = MODE_DFP_DP | MODE_DFP_USB;
+		data = state->data;
+		hpd = !!(data->status & DP_STATUS_HPD_STATE);
+		phy_set_bus_width(tcphy->phys[TYPEC_PHY_DP], hpd ? 2 : 0);
+		break;
+	default:
+		break;
+	}
+
+	mutex_unlock(&tcphy->lock);
+
+	return 0;
+}
+
+static void tcphy_typec_mux_unregister(void *data)
+{
+	struct rockchip_typec_phy *tcphy = data;
+
+	typec_mux_unregister(tcphy->mux);
+}
+
+static int tcphy_setup_typec_mux(struct rockchip_typec_phy *tcphy)
+{
+	struct typec_mux_desc mux_desc = {};
+	struct device_node *np;
+	int ret = 0;
+
+	np = of_get_child_by_name(tcphy->dev->of_node, "dp-port");
+	if (!np)
+		return 0;
+
+	if (!of_property_read_bool(np, "mode-switch"))
+		goto put_np;
+
+	mux_desc.drvdata = tcphy;
+	mux_desc.fwnode = device_get_named_child_node(tcphy->dev, "dp-port");
+	mux_desc.set = tcphy_typec_mux_set;
+
+	tcphy->mux = typec_mux_register(tcphy->dev, &mux_desc);
+	if (IS_ERR(tcphy->mux)) {
+		dev_err(tcphy->dev, "Error register typec mux: %ld\n",
+			PTR_ERR(tcphy->mux));
+		ret = PTR_ERR(tcphy->mux);
+		goto put_np;
+	}
+
+	ret = devm_add_action_or_reset(tcphy->dev, tcphy_typec_mux_unregister, tcphy);
+
+put_np:
+	of_node_put(np);
+	return ret;
+}
+#else
+static int tcphy_setup_typec_mux(struct rockchip_typec_phy *tcphy)
+{
+	return 0;
+}
+#endif
+
 static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
 			  struct device *dev)
 {
@@ -1095,6 +1395,25 @@ static void typec_phy_pre_init(struct rockchip_typec_phy *tcphy)
 	tcphy->mode = MODE_DISCONNECT;
 }
 
+static int typec_dp_lane_get(struct rockchip_typec_phy *tcphy)
+{
+	int dp_lanes;
+
+	switch (tcphy->new_mode) {
+	case MODE_DFP_DP:
+		dp_lanes = 4;
+		break;
+	case MODE_DFP_DP | MODE_DFP_USB:
+		dp_lanes = 2;
+		break;
+	default:
+		dp_lanes = 0;
+		break;
+	}
+
+	return dp_lanes;
+}
+
 static int rockchip_typec_phy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -1142,6 +1461,7 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
 		return ret;
 
 	tcphy->dev = dev;
+	tcphy->new_mode = MODE_DFP_USB;
 	platform_set_drvdata(pdev, tcphy);
 	mutex_init(&tcphy->lock);
 
@@ -1151,6 +1471,7 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(tcphy->extcon)) {
 		if (PTR_ERR(tcphy->extcon) == -ENODEV) {
 			tcphy->extcon = NULL;
+			dev_info(dev, "extcon not exist, try to use typec mux\n");
 		} else {
 			if (PTR_ERR(tcphy->extcon) != -EPROBE_DEFER)
 				dev_err(dev, "Invalid or missing extcon\n");
@@ -1158,19 +1479,34 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
 		}
 	}
 
+	ret = tcphy_setup_orien_switch(tcphy);
+	if (ret)
+		return ret;
+
+	ret = tcphy_setup_typec_mux(tcphy);
+	if (ret)
+		return ret;
+
 	pm_runtime_enable(dev);
 
 	for_each_available_child_of_node(np, child_np) {
 		struct phy *phy;
 
-		if (of_node_name_eq(child_np, "dp-port"))
+		if (of_node_name_eq(child_np, "dp-port")) {
 			phy = devm_phy_create(dev, child_np,
 					      &rockchip_dp_phy_ops);
-		else if (of_node_name_eq(child_np, "usb3-port"))
+			if (!IS_ERR(phy)) {
+				tcphy->phys[TYPEC_PHY_DP] = phy;
+				phy_set_bus_width(phy, typec_dp_lane_get(tcphy));
+			}
+		} else if (of_node_name_eq(child_np, "usb3-port")) {
 			phy = devm_phy_create(dev, child_np,
 					      &rockchip_usb3_phy_ops);
-		else
+			if (!IS_ERR(phy))
+				tcphy->phys[TYPEC_PHY_USB] = phy;
+		} else {
 			continue;
+		}
 
 		if (IS_ERR(phy)) {
 			dev_err(dev, "failed to create phy: %pOFn\n",
-- 
2.49.0

[PATCH v6 4/8] phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

Using the DRM_AUX_BRIDGE helper to create the transparent DRM bridge
device.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

Changes in v6:
- Fix depend in Kconfig. 

 drivers/phy/rockchip/Kconfig              |  2 +
 drivers/phy/rockchip/phy-rockchip-typec.c | 52 +++++++++++++++++++++++
 2 files changed, 54 insertions(+)

diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
index db4adc7c53da..bcb5476222fc 100644
--- a/drivers/phy/rockchip/Kconfig
+++ b/drivers/phy/rockchip/Kconfig
@@ -120,6 +120,8 @@ config PHY_ROCKCHIP_TYPEC
 	tristate "Rockchip TYPEC PHY Driver"
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
 	depends on TYPEC || TYPEC=n
+	depends on DRM || DRM=n
+	select DRM_AUX_BRIDGE if DRM_BRIDGE
 	select EXTCON
 	select GENERIC_PHY
 	select RESET_CONTROLLER
diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
index 1f5b4142cbe4..748a6eb8ad95 100644
--- a/drivers/phy/rockchip/phy-rockchip-typec.c
+++ b/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -36,6 +36,7 @@
  * orientation, false is normal orientation.
  */
 
+#include <linux/auxiliary_bus.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/delay.h>
@@ -56,6 +57,7 @@
 #include <linux/phy/phy.h>
 #include <linux/usb/typec_dp.h>
 #include <linux/usb/typec_mux.h>
+#include <drm/bridge/aux-bridge.h>
 
 #define CMN_SSM_BANDGAP			(0x21 << 2)
 #define CMN_SSM_BIAS			(0x22 << 2)
@@ -415,6 +417,7 @@ struct rockchip_usb3phy_port_cfg {
 
 struct rockchip_typec_phy {
 	struct device *dev;
+	struct auxiliary_device dp_port_dev;
 	void __iomem *base;
 	struct extcon_dev *extcon;
 	struct typec_mux_dev *mux;
@@ -1299,6 +1302,51 @@ static void tcphy_typec_mux_unregister(void *data)
 	typec_mux_unregister(tcphy->mux);
 }
 
+static void tcphy_dp_port_dev_release(struct device *dev)
+{
+	struct auxiliary_device *adev = to_auxiliary_dev(dev);
+
+	of_node_put(adev->dev.of_node);
+}
+
+static void tcphy_dp_port_unregister_adev(void *_adev)
+{
+	struct auxiliary_device *adev = _adev;
+
+	auxiliary_device_delete(adev);
+	auxiliary_device_uninit(adev);
+}
+
+static int tcphy_aux_bridge_register(struct rockchip_typec_phy *tcphy, struct device_node *np)
+{
+	struct auxiliary_device *adev = &tcphy->dp_port_dev;
+	int ret;
+
+	adev->name = "dp_port";
+	adev->dev.parent = tcphy->dev;
+	adev->dev.of_node = of_node_get(np);
+	adev->dev.release = tcphy_dp_port_dev_release;
+
+	ret = auxiliary_device_init(adev);
+
+	if (ret) {
+		of_node_put(adev->dev.of_node);
+		return ret;
+	}
+
+	ret = auxiliary_device_add(adev);
+	if (ret) {
+		auxiliary_device_uninit(adev);
+		return ret;
+	}
+
+	devm_add_action_or_reset(tcphy->dev, tcphy_dp_port_unregister_adev, adev);
+
+	ret = drm_aux_bridge_register(&adev->dev);
+
+	return 0;
+}
+
 static int tcphy_setup_typec_mux(struct rockchip_typec_phy *tcphy)
 {
 	struct typec_mux_desc mux_desc = {};
@@ -1312,6 +1360,10 @@ static int tcphy_setup_typec_mux(struct rockchip_typec_phy *tcphy)
 	if (!of_property_read_bool(np, "mode-switch"))
 		goto put_np;
 
+	ret = tcphy_aux_bridge_register(tcphy, np);
+	if (ret)
+		goto put_np;
+
 	mux_desc.drvdata = tcphy;
 	mux_desc.fwnode = device_get_named_child_node(tcphy->dev, "dp-port");
 	mux_desc.set = tcphy_typec_mux_set;
-- 
2.49.0

[PATCH v6 5/8] drm/rockchip: cdn-dp: Support handle lane info without extcon

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

This patch add support for get PHY lane info without help of extcon.

There is no extcon needed if the Type-C controller is present. In this
case, the lane info can be get from PHY instead of extcon.

The extcon device should still be supported if Type-C controller is
not present.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

(no changes since v5)

Changes in v4:
- Remove cdn_dp_hpd_notify().

(no changes since v3)

Changes in v2:
- Ignore duplicate HPD events.

 drivers/gpu/drm/rockchip/cdn-dp-core.c | 25 +++++++++++++++++--------
 1 file changed, 17 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
index b7e3f5dcf8d5..1e27301584a4 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -156,6 +156,9 @@ static int cdn_dp_get_port_lanes(struct cdn_dp_port *port)
 	int dptx;
 	u8 lanes;
 
+	if (!edev)
+		return phy_get_bus_width(port->phy);
+
 	dptx = extcon_get_state(edev, EXTCON_DISP_DP);
 	if (dptx > 0) {
 		extcon_get_property(edev, EXTCON_DISP_DP,
@@ -219,7 +222,7 @@ static bool cdn_dp_check_sink_connection(struct cdn_dp_device *dp)
 	 * some docks need more time to power up.
 	 */
 	while (time_before(jiffies, timeout)) {
-		if (!extcon_get_state(port->extcon, EXTCON_DISP_DP))
+		if (port->extcon && !extcon_get_state(port->extcon, EXTCON_DISP_DP))
 			return false;
 
 		if (!cdn_dp_get_sink_count(dp, &sink_count))
@@ -385,11 +388,14 @@ static int cdn_dp_enable_phy(struct cdn_dp_device *dp, struct cdn_dp_port *port)
 		goto err_power_on;
 	}
 
-	ret = extcon_get_property(port->extcon, EXTCON_DISP_DP,
-				  EXTCON_PROP_USB_TYPEC_POLARITY, &property);
-	if (ret) {
-		DRM_DEV_ERROR(dp->dev, "get property failed\n");
-		goto err_power_on;
+	property.intval = 0;
+	if (port->extcon) {
+		ret = extcon_get_property(port->extcon, EXTCON_DISP_DP,
+					  EXTCON_PROP_USB_TYPEC_POLARITY, &property);
+		if (ret) {
+			DRM_DEV_ERROR(dp->dev, "get property failed\n");
+			goto err_power_on;
+		}
 	}
 
 	port->lanes = cdn_dp_get_port_lanes(port);
@@ -1028,6 +1034,9 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 	for (i = 0; i < dp->ports; i++) {
 		port = dp->port[i];
 
+		if (!port->extcon)
+			continue;
+
 		port->event_nb.notifier_call = cdn_dp_pd_event;
 		ret = devm_extcon_register_notifier(dp->dev, port->extcon,
 						    EXTCON_DISP_DP,
@@ -1120,14 +1129,14 @@ static int cdn_dp_probe(struct platform_device *pdev)
 		    PTR_ERR(phy) == -EPROBE_DEFER)
 			return -EPROBE_DEFER;
 
-		if (IS_ERR(extcon) || IS_ERR(phy))
+		if (IS_ERR(phy) || PTR_ERR(extcon) != -ENODEV)
 			continue;
 
 		port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
 		if (!port)
 			return -ENOMEM;
 
-		port->extcon = extcon;
+		port->extcon = IS_ERR(extcon) ? NULL : extcon;
 		port->phy = phy;
 		port->dp = dp;
 		port->id = i;
-- 
2.49.0

[PATCH v6 6/8] drm/rockchip: cdn-dp: Add multiple bridges to support PHY port selection

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

The RK3399 has two USB/DP combo PHY and one CDN-DP controller. And
the CDN-DP can be switched to output to one of the PHYs. If both ports
are plugged into DP, DP will select the first port for output.

This patch adds support for multiple bridges, enabling users to flexibly
select the output port. For each PHY port, a separate encoder and bridge
are registered.

The change is based on the DRM AUX HPD bridge, rather than the
extcon approach. This requires the DT to correctly describe the
connections between the first bridge in bridge chain and DP
controller. For example, the bridge chain may be like this:

PHY aux birdge -> fsa4480 analog audio switch bridge ->
onnn,nb7vpq904m USB reminder bridge -> USB-C controller AUX HPD bridge

In this case, the connection relationships among the PHY aux bridge
and the DP contorller need to be described in DT.

In addition, the cdn_dp_parse_next_bridge_dt() will parses it and
determines whether to register one or two bridges.

Since there is only one DP controller, only one of the PHY ports can
output at a time. The key is how to switch between different PHYs,
which is handled by cdn_dp_switch_port() and cdn_dp_enable().

There are two cases:

1. Neither bridge is enabled. In this case, both bridges can
independently read the EDID, and the PHY port may switch before
reading the EDID.

2. One bridge is already enabled. In this case, other bridges are not
allowed to read the EDID. So we will try to return the cached EDID.

Since the scenario of two ports plug in at the same time is rare,
I don't have a board which support two TypeC connector to test this.
Therefore, I tested forced switching on a single PHY port, as well as
output using a fake PHY port alongside a real PHY port.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

Changes in v6:
- Rename some variable names.
- Attach the DP bridge to the next bridge.

Changes in v5:
- By parsing the HPD bridge chain, set the connector's of_node to the
of_node corresponding to the USB-C connector.
- Return EDID cache when other port is already enabled.

 drivers/gpu/drm/rockchip/cdn-dp-core.c | 329 ++++++++++++++++++++-----
 drivers/gpu/drm/rockchip/cdn-dp-core.h |  24 +-
 2 files changed, 296 insertions(+), 57 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
index 1e27301584a4..5c0e5209d3b8 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -27,16 +27,17 @@
 #include "cdn-dp-core.h"
 #include "cdn-dp-reg.h"
 
-static inline struct cdn_dp_device *bridge_to_dp(struct drm_bridge *bridge)
+static int cdn_dp_switch_port(struct cdn_dp_device *dp, struct cdn_dp_port *prev_port,
+			      struct cdn_dp_port *port);
+
+static inline struct cdn_dp_bridge *bridge_to_dp_bridge(struct drm_bridge *bridge)
 {
-	return container_of(bridge, struct cdn_dp_device, bridge);
+	return container_of(bridge, struct cdn_dp_bridge, bridge);
 }
 
-static inline struct cdn_dp_device *encoder_to_dp(struct drm_encoder *encoder)
+static inline struct cdn_dp_device *bridge_to_dp(struct drm_bridge *bridge)
 {
-	struct rockchip_encoder *rkencoder = to_rockchip_encoder(encoder);
-
-	return container_of(rkencoder, struct cdn_dp_device, encoder);
+	return bridge_to_dp_bridge(bridge)->parent;
 }
 
 #define GRF_SOC_CON9		0x6224
@@ -191,14 +192,27 @@ static int cdn_dp_get_sink_count(struct cdn_dp_device *dp, u8 *sink_count)
 static struct cdn_dp_port *cdn_dp_connected_port(struct cdn_dp_device *dp)
 {
 	struct cdn_dp_port *port;
-	int i, lanes;
+	int i, lanes[MAX_PHY];
 
 	for (i = 0; i < dp->ports; i++) {
 		port = dp->port[i];
-		lanes = cdn_dp_get_port_lanes(port);
-		if (lanes)
+		lanes[i] = cdn_dp_get_port_lanes(port);
+		if (!dp->next_bridge_valid)
 			return port;
 	}
+
+	if (dp->next_bridge_valid) {
+		/* If more than one port is available, pick the last active port */
+		if (dp->active_port > 0 && lanes[dp->active_port])
+			return dp->port[dp->active_port];
+
+		/* If the last active port is not available, pick an available port in order */
+		for (i = 0; i < dp->bridge_count; i++) {
+			if (lanes[i])
+				return dp->port[i];
+		}
+	}
+
 	return NULL;
 }
 
@@ -253,12 +267,45 @@ static const struct drm_edid *
 cdn_dp_bridge_edid_read(struct drm_bridge *bridge, struct drm_connector *connector)
 {
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
-	const struct drm_edid *drm_edid;
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
+	struct cdn_dp_port *port = dp->port[dp_bridge->id];
+	struct cdn_dp_port *prev_port;
+	const struct drm_edid *drm_edid = NULL;
+	int i, ret;
 
 	mutex_lock(&dp->lock);
+
+	/* More than one port is available */
+	if (dp->bridge_count > 1 && !port->phy_enabled) {
+		for (i = 0; i < dp->bridge_count; i++) {
+			/* Another port already enable */
+			if (dp->bridge_list[i] != dp_bridge && dp->bridge_list[i]->enabled)
+				goto get_cache;
+			/* Find already enabled port */
+			if (dp->port[i]->phy_enabled)
+				prev_port = dp->port[i];
+		}
+
+		/* Switch to current port */
+		if (prev_port) {
+			ret = cdn_dp_switch_port(dp, prev_port, port);
+			if (ret)
+				goto get_cache;
+		}
+	}
+
 	drm_edid = drm_edid_read_custom(connector, cdn_dp_get_edid_block, dp);
+	/* replace edid cache */
+	if (dp->edid_cache[dp_bridge->id])
+		drm_edid_free(dp->edid_cache[dp_bridge->id]);
+	dp->edid_cache[dp_bridge->id] = drm_edid_dup(drm_edid);
+
 	mutex_unlock(&dp->lock);
+	return drm_edid;
 
+get_cache:
+	drm_edid = drm_edid_dup(dp->edid_cache[dp_bridge->id]);
+	mutex_unlock(&dp->lock);
 	return drm_edid;
 }
 
@@ -267,12 +314,13 @@ cdn_dp_bridge_mode_valid(struct drm_bridge *bridge,
 			 const struct drm_display_info *display_info,
 			 const struct drm_display_mode *mode)
 {
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
 	u32 requested, actual, rate, sink_max, source_max = 0;
 	u8 lanes, bpc;
 
 	/* If DP is disconnected, every mode is invalid */
-	if (!dp->connected)
+	if (!dp_bridge->connected || !dp->connected)
 		return MODE_BAD;
 
 	switch (display_info->bpc) {
@@ -550,6 +598,54 @@ static bool cdn_dp_check_link_status(struct cdn_dp_device *dp)
 	return drm_dp_channel_eq_ok(link_status, min(port->lanes, sink_lanes));
 }
 
+static int cdn_dp_switch_port(struct cdn_dp_device *dp, struct cdn_dp_port *prev_port,
+			      struct cdn_dp_port *port)
+{
+	int ret;
+
+	if (dp->active)
+		return 0;
+
+	ret = cdn_dp_disable_phy(dp, prev_port);
+	if (ret)
+		goto out;
+	ret = cdn_dp_enable_phy(dp, port);
+	if (ret)
+		goto out;
+
+	ret = cdn_dp_get_sink_capability(dp);
+	if (ret) {
+		cdn_dp_disable_phy(dp, port);
+		goto out;
+	}
+
+	dp->active = true;
+	dp->lanes = port->lanes;
+
+	if (!cdn_dp_check_link_status(dp)) {
+		dev_info(dp->dev, "Connected with sink; re-train link\n");
+
+		ret = cdn_dp_train_link(dp);
+		if (ret) {
+			dev_err(dp->dev, "Training link failed: %d\n", ret);
+			goto out;
+		}
+
+		ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_IDLE);
+		if (ret) {
+			dev_err(dp->dev, "Failed to idle video %d\n", ret);
+			goto out;
+		}
+
+		ret = cdn_dp_config_video(dp);
+		if (ret)
+			dev_err(dp->dev, "Failed to configure video: %d\n", ret);
+	}
+
+out:
+	return ret;
+}
+
 static void cdn_dp_display_info_update(struct cdn_dp_device *dp,
 				       struct drm_display_info *display_info)
 {
@@ -571,6 +667,7 @@ static void cdn_dp_display_info_update(struct cdn_dp_device *dp,
 static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_atomic_state *state)
 {
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
 	struct drm_connector *connector;
 	int ret, val;
 
@@ -580,7 +677,7 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 
 	cdn_dp_display_info_update(dp, &connector->display_info);
 
-	ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, &dp->encoder.encoder);
+	ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, &dp_bridge->encoder.encoder);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dp->dev, "Could not get vop id, %d", ret);
 		return;
@@ -599,6 +696,9 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 
 	mutex_lock(&dp->lock);
 
+	if (dp->next_bridge_valid)
+		dp->active_port = dp_bridge->id;
+
 	ret = cdn_dp_enable(dp);
 	if (ret) {
 		DRM_DEV_ERROR(dp->dev, "Failed to enable bridge %d\n",
@@ -631,6 +731,7 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 		goto out;
 	}
 
+	dp_bridge->enabled = true;
 out:
 	mutex_unlock(&dp->lock);
 }
@@ -638,9 +739,11 @@ static void cdn_dp_bridge_atomic_enable(struct drm_bridge *bridge, struct drm_at
 static void cdn_dp_bridge_atomic_disable(struct drm_bridge *bridge, struct drm_atomic_state *state)
 {
 	struct cdn_dp_device *dp = bridge_to_dp(bridge);
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
 	int ret;
 
 	mutex_lock(&dp->lock);
+	dp_bridge->enabled = false;
 
 	if (dp->active) {
 		ret = cdn_dp_disable(dp);
@@ -827,6 +930,16 @@ static int cdn_dp_audio_mute_stream(struct drm_bridge *bridge,
 	return ret;
 }
 
+static void cdn_dp_bridge_hpd_notify(struct drm_bridge *bridge,
+			   enum drm_connector_status status)
+{
+	struct cdn_dp_bridge *dp_bridge = bridge_to_dp_bridge(bridge);
+	struct cdn_dp_device *dp = bridge_to_dp(bridge);
+
+	dp->bridge_list[dp_bridge->id]->connected = status == connector_status_connected;
+	schedule_work(&dp->event_work);
+}
+
 static const struct drm_bridge_funcs cdn_dp_bridge_funcs = {
 	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
 	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
@@ -837,6 +950,7 @@ static const struct drm_bridge_funcs cdn_dp_bridge_funcs = {
 	.atomic_disable = cdn_dp_bridge_atomic_disable,
 	.mode_valid = cdn_dp_bridge_mode_valid,
 	.mode_set = cdn_dp_bridge_mode_set,
+	.hpd_notify = cdn_dp_bridge_hpd_notify,
 
 	.dp_audio_prepare = cdn_dp_audio_prepare,
 	.dp_audio_mute_stream = cdn_dp_audio_mute_stream,
@@ -885,7 +999,8 @@ static void cdn_dp_pd_event_work(struct work_struct *work)
 {
 	struct cdn_dp_device *dp = container_of(work, struct cdn_dp_device,
 						event_work);
-	int ret;
+	bool connected;
+	int i, ret;
 
 	mutex_lock(&dp->lock);
 
@@ -944,9 +1059,12 @@ static void cdn_dp_pd_event_work(struct work_struct *work)
 
 out:
 	mutex_unlock(&dp->lock);
-	drm_bridge_hpd_notify(&dp->bridge,
-			      dp->connected ? connector_status_connected
-					    : connector_status_disconnected);
+	for (i = 0; i < dp->bridge_count; i++) {
+		connected = dp->connected && dp->bridge_list[i]->connected;
+		drm_bridge_hpd_notify(&dp->bridge_list[i]->bridge,
+				      connected ? connector_status_connected
+						: connector_status_disconnected);
+	}
 }
 
 static int cdn_dp_pd_event(struct notifier_block *nb,
@@ -966,28 +1084,16 @@ static int cdn_dp_pd_event(struct notifier_block *nb,
 	return NOTIFY_DONE;
 }
 
-static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
+static int cdn_bridge_add(struct device *dev,
+			  struct drm_bridge *bridge,
+			  struct drm_bridge *next_bridge,
+			  struct drm_encoder *encoder)
 {
 	struct cdn_dp_device *dp = dev_get_drvdata(dev);
-	struct drm_encoder *encoder;
+	struct drm_device *drm_dev = dp->drm_dev;
+	struct drm_bridge *last_bridge = NULL;
 	struct drm_connector *connector;
-	struct cdn_dp_port *port;
-	struct drm_device *drm_dev = data;
-	int ret, i;
-
-	ret = cdn_dp_parse_dt(dp);
-	if (ret < 0)
-		return ret;
-
-	dp->drm_dev = drm_dev;
-	dp->connected = false;
-	dp->active = false;
-	dp->active_port = -1;
-	dp->fw_loaded = false;
-
-	INIT_WORK(&dp->event_work, cdn_dp_pd_event_work);
-
-	encoder = &dp->encoder.encoder;
+	int ret;
 
 	encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev,
 							     dev->of_node);
@@ -1002,26 +1108,38 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 
 	drm_encoder_helper_add(encoder, &cdn_dp_encoder_helper_funcs);
 
-	dp->bridge.ops =
-			DRM_BRIDGE_OP_DETECT |
-			DRM_BRIDGE_OP_EDID |
-			DRM_BRIDGE_OP_HPD |
-			DRM_BRIDGE_OP_DP_AUDIO;
-	dp->bridge.of_node = dp->dev->of_node;
-	dp->bridge.type = DRM_MODE_CONNECTOR_DisplayPort;
-	dp->bridge.hdmi_audio_dev = dp->dev;
-	dp->bridge.hdmi_audio_max_i2s_playback_channels = 8;
-	dp->bridge.hdmi_audio_spdif_playback = 1;
-	dp->bridge.hdmi_audio_dai_port = -1;
-
-	ret = devm_drm_bridge_add(dev, &dp->bridge);
+
+	bridge->ops =
+		DRM_BRIDGE_OP_DETECT |
+		DRM_BRIDGE_OP_EDID |
+		DRM_BRIDGE_OP_HPD |
+		DRM_BRIDGE_OP_DP_AUDIO;
+	bridge->of_node = dp->dev->of_node;
+	bridge->type = DRM_MODE_CONNECTOR_DisplayPort;
+	bridge->hdmi_audio_dev = dp->dev;
+	bridge->hdmi_audio_max_i2s_playback_channels = 8;
+	bridge->hdmi_audio_spdif_playback = 1;
+	bridge->hdmi_audio_dai_port = -1;
+
+	ret = devm_drm_bridge_add(dev, bridge);
 	if (ret)
 		return ret;
 
-	ret = drm_bridge_attach(encoder, &dp->bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+	ret = drm_bridge_attach(encoder, bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
 	if (ret)
 		return ret;
 
+	if (next_bridge) {
+		ret = drm_bridge_attach(encoder, next_bridge, bridge,
+					DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+		if (ret)
+			return ret;
+
+		last_bridge = next_bridge;
+		while (drm_bridge_get_next_bridge(last_bridge))
+			last_bridge = drm_bridge_get_next_bridge(last_bridge);
+	}
+
 	connector = drm_bridge_connector_init(drm_dev, encoder);
 	if (IS_ERR(connector)) {
 		ret = PTR_ERR(connector);
@@ -1029,8 +1147,102 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 		return ret;
 	}
 
+	if (last_bridge)
+		connector->fwnode = fwnode_handle_get(of_fwnode_handle(last_bridge->of_node));
+
 	drm_connector_attach_encoder(connector, encoder);
 
+	return 0;
+}
+
+static int cdn_dp_parse_next_bridge_dt(struct cdn_dp_device *dp)
+{
+	struct device_node *np = dp->dev->of_node;
+	struct device_node *port __free(device_node) = of_graph_get_port_by_id(np, 1);
+	struct drm_bridge *bridge;
+	int count = 0;
+	int ret = 0;
+	int i;
+
+	/* If device use extcon, do not use hpd bridge */
+	for (i = 0; i < dp->ports; i++) {
+		if (dp->port[i]->extcon) {
+			dp->bridge_count = 1;
+			return 0;
+		}
+	}
+
+
+	/* One endpoint may correspond to one next bridge. */
+	for_each_of_graph_port_endpoint(port, dp_ep) {
+		struct device_node *next_bridge_node __free(device_node) =
+			of_graph_get_remote_port_parent(dp_ep);
+
+		bridge = of_drm_find_bridge(next_bridge_node);
+		if (!bridge) {
+			ret = -EPROBE_DEFER;
+			goto out;
+		}
+
+		dp->next_bridge_valid = true;
+		dp->next_bridge_list[count].bridge = bridge;
+		dp->next_bridge_list[count].parent = dp;
+		dp->next_bridge_list[count].id = count;
+		count++;
+	}
+
+out:
+	dp->bridge_count = count ? count : 1;
+	return ret;
+}
+
+static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
+{
+	struct cdn_dp_device *dp = dev_get_drvdata(dev);
+	struct drm_bridge *bridge, *next_bridge;
+	struct drm_encoder *encoder;
+	struct cdn_dp_port *port;
+	struct drm_device *drm_dev = data;
+	struct cdn_dp_bridge *dp_bridge;
+	int ret, i;
+
+	ret = cdn_dp_parse_dt(dp);
+	if (ret < 0)
+		return ret;
+
+	ret = cdn_dp_parse_next_bridge_dt(dp);
+	if (ret)
+		return ret;
+
+	dp->drm_dev = drm_dev;
+	dp->connected = false;
+	dp->active = false;
+	dp->active_port = -1;
+	dp->fw_loaded = false;
+
+	for (i = 0; i < dp->bridge_count; i++) {
+		dp_bridge = devm_drm_bridge_alloc(dev, struct cdn_dp_bridge, bridge,
+						    &cdn_dp_bridge_funcs);
+		if (IS_ERR(dp_bridge))
+			return PTR_ERR(dp_bridge);
+		dp_bridge->id = i;
+		dp_bridge->parent = dp;
+		if (!dp->next_bridge_valid)
+			dp_bridge->connected = true;
+		dp->bridge_list[i] = dp_bridge;
+	}
+
+	for (i = 0; i < dp->bridge_count; i++) {
+		encoder = &dp->bridge_list[i]->encoder.encoder;
+		bridge = &dp->bridge_list[i]->bridge;
+		next_bridge = dp->next_bridge_list[i].bridge;
+		ret = cdn_bridge_add(dev, bridge, next_bridge, encoder);
+		if (ret)
+			return ret;
+	}
+
+	INIT_WORK(&dp->event_work, cdn_dp_pd_event_work);
+
 	for (i = 0; i < dp->ports; i++) {
 		port = dp->port[i];
 
@@ -1058,10 +1270,17 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
 static void cdn_dp_unbind(struct device *dev, struct device *master, void *data)
 {
 	struct cdn_dp_device *dp = dev_get_drvdata(dev);
-	struct drm_encoder *encoder = &dp->encoder.encoder;
+	struct drm_encoder *encoder;
+	int i;
 
 	cancel_work_sync(&dp->event_work);
-	encoder->funcs->destroy(encoder);
+	for (i = 0; i < dp->bridge_count; i++) {
+		encoder = &dp->bridge_list[i]->encoder.encoder;
+		encoder->funcs->destroy(encoder);
+	}
+
+	for (i = 0; i < MAX_PHY; i++)
+		drm_edid_free(dp->edid_cache[i]);
 
 	pm_runtime_disable(dev);
 	if (dp->fw_loaded)
@@ -1112,10 +1331,10 @@ static int cdn_dp_probe(struct platform_device *pdev)
 	int ret;
 	int i;
 
-	dp = devm_drm_bridge_alloc(dev, struct cdn_dp_device, bridge,
-				   &cdn_dp_bridge_funcs);
-	if (IS_ERR(dp))
-		return PTR_ERR(dp);
+	dp = devm_kzalloc(dev, sizeof(*dp), GFP_KERNEL);
+	if (!dp)
+		return -ENOMEM;
+
 	dp->dev = dev;
 
 	match = of_match_node(cdn_dp_dt_ids, pdev->dev.of_node);
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.h b/drivers/gpu/drm/rockchip/cdn-dp-core.h
index e9c30b9fd543..ce1707a5c746 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.h
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.h
@@ -38,6 +38,8 @@ enum vic_pxl_encoding_format {
 	Y_ONLY = 0x10,
 };
 
+struct cdn_dp_device;
+
 struct video_info {
 	bool h_sync_polarity;
 	bool v_sync_polarity;
@@ -63,16 +65,34 @@ struct cdn_dp_port {
 	u8 id;
 };
 
+struct cdn_dp_bridge {
+	struct cdn_dp_device *parent;
+	struct drm_bridge bridge;
+	struct rockchip_encoder encoder;
+	bool connected;
+	bool enabled;
+	int id;
+};
+
+struct cdn_dp_next_bridge {
+	struct cdn_dp_device *parent;
+	struct drm_bridge *bridge;
+	int id;
+};
+
 struct cdn_dp_device {
 	struct device *dev;
 	struct drm_device *drm_dev;
-	struct drm_bridge bridge;
-	struct rockchip_encoder encoder;
+	int bridge_count;
+	struct cdn_dp_bridge *bridge_list[MAX_PHY];
+	struct cdn_dp_next_bridge next_bridge_list[MAX_PHY];
+	const struct drm_edid *edid_cache[MAX_PHY];
 	struct drm_display_mode mode;
 	struct platform_device *audio_pdev;
 	struct work_struct event_work;
 
 	struct mutex lock;
+	bool next_bridge_valid;
 	bool connected;
 	bool active;
 	bool suspended;
-- 
2.49.0

[PATCH v6 7/8] arm64: dts: rockchip: Add missing dp_out port for RK3399 CDN-DP

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

Let's make the ports nodes of cdn_dp in the same style as the other
display interface, and match the style of ports's yaml.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

(no changes since v5)

Changes in v4:
- Remove unnecessary #address/#size-cells

(no changes since v1)

 arch/arm64/boot/dts/rockchip/rk3399-base.dtsi | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-base.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-base.dtsi
index 4dcceb9136b7..93b42820998f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-base.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-base.dtsi
@@ -618,7 +618,11 @@ cdn_dp: dp@fec00000 {
 		status = "disabled";
 
 		ports {
-			dp_in: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dp_in: port@0 {
+				reg = <0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -632,6 +636,10 @@ dp_in_vopl: endpoint@1 {
 					remote-endpoint = <&vopl_out_dp>;
 				};
 			};
+
+			dp_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};
 
-- 
2.49.0

[PATCH v6 8/8] arm64: dts: rockchip: rk3399-evb-ind: Add support for DisplayPort

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

The RK3399 EVB IND board has a Type-C interface DisplayPort.
It use fusb302 chip as Type-C controller.

fusb302 chip ---> USB/DP PHY0 <----> CDN-DP controller

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---

(no changes since v4)

Changes in v3:
- Fix wrong vdo value.
- Fix port node in usb-c-connector.

Changes in v2:
- Add endpoint to link DP PHY and DP controller.
- Fix devicetree coding style.

 .../boot/dts/rockchip/rk3399-evb-ind.dts      | 146 ++++++++++++++++++
 1 file changed, 146 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts
index 70aee1ab904c..aeeee6bd2973 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts
@@ -4,6 +4,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/usb/pd.h>
 #include "rk3399.dtsi"
 
 / {
@@ -19,6 +20,21 @@ chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
+	sound: sound {
+		compatible = "rockchip,rk3399-gru-sound";
+		rockchip,cpu = <&i2s0 &spdif>;
+	};
+
+	vbus_typec: regulator-vbus-typec {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_typec0_en>;
+		regulator-name = "vbus_typec";
+		vin-supply = <&vcc5v0_sys>;
+	};
+
 	vcc5v0_sys: regulator-vcc5v0-sys {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -31,6 +47,11 @@ vcc5v0_sys: regulator-vcc5v0-sys {
 	};
 };
 
+&cdn_dp {
+	phys = <&tcphy0_dp>;
+	status = "okay";
+};
+
 &cpu_b0 {
 	cpu-supply = <&vdd_cpu_b>;
 };
@@ -55,6 +76,12 @@ &cpu_l3 {
 	cpu-supply = <&vdd_cpu_l>;
 };
 
+&dp_out {
+	dp_controller_output: endpoint {
+		remote-endpoint = <&dp_phy_in>;
+	};
+};
+
 &emmc_phy {
 	status = "okay";
 };
@@ -341,6 +368,71 @@ regulator-state-mem {
 	};
 };
 
+&i2c4 {
+	i2c-scl-rising-time-ns = <475>;
+	i2c-scl-falling-time-ns = <26>;
+	status = "okay";
+
+	usbc0: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usbc0_int>;
+		vbus-supply = <&vbus_typec>;
+
+		usb_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "sink";
+			op-sink-microwatt = <1000000>;
+			sink-pdos =
+				<PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
+			source-pdos =
+				<PDO_FIXED(5000, 1500, PDO_FIXED_USB_COMM)>;
+
+			altmodes {
+				displayport {
+					svid = /bits/ 16 <0xff01>;
+					vdo = <0x00001c46>;
+				};
+			};
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usbc_hs: endpoint {
+						remote-endpoint = <&u2phy0_typec_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usbc_ss: endpoint {
+						remote-endpoint = <&tcphy0_typec_ss>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usbc_dp: endpoint {
+						remote-endpoint = <&tcphy0_typec_dp>;
+					};
+				};
+			};
+		};
+	};
+};
+
 &i2s2 {
 	status = "okay";
 };
@@ -354,6 +446,16 @@ &io_domains {
 };
 
 &pinctrl {
+	usb-typec {
+		usbc0_int: usbc0-int {
+			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vcc5v0_typec0_en: vcc5v0-typec0-en {
+			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		pmic_int_l: pmic-int-l {
 			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
@@ -400,10 +502,48 @@ &sdmmc {
 	status = "okay";
 };
 
+&sound {
+	rockchip,codec = <&cdn_dp>;
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
 &tcphy0 {
 	status = "okay";
 };
 
+&tcphy0_dp {
+	mode-switch;
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		tcphy0_typec_dp: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&usbc_dp>;
+		};
+
+		dp_phy_in: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&dp_controller_output>;
+		};
+	};
+};
+
+&tcphy0_usb3 {
+	orientation-switch;
+
+	port {
+		tcphy0_typec_ss: endpoint {
+			remote-endpoint = <&usbc_ss>;
+		};
+	};
+};
+
 &tcphy1 {
 	status = "okay";
 };
@@ -418,6 +558,12 @@ &tsadc {
 
 &u2phy0 {
 	status = "okay";
+
+	port {
+		u2phy0_typec_hs: endpoint {
+			remote-endpoint = <&usbc_hs>;
+		};
+	};
 };
 
 &u2phy0_host {
-- 
2.49.0

Re: [PATCH v6 0/8] Add Type-C DP support for RK3399 EVB IND board

[Rob Herring (Arm)]

On Thu, 16 Oct 2025 10:27:33 +0800, Chaoyi Chen wrote:
> From: Chaoyi Chen <chaoyi.chen@rock-chips.com>
> 
> This series focuses on adding Type-C DP support for USBDP PHY and DP
> driver. The USBDP PHY and DP will perceive the changes in cable status
> based on the USB PD and Type-C state machines provided by TCPM. Before
> this, the USBDP PHY and DP controller of RK3399 sensed cable state
> changes through extcon, and devices such as the RK3399 Gru-Chromebook
> rely on them. This series should not break them.
> 
> ====
> 1. DisplayPort HPD status notify
> 
> Before v4, I implemented a variety of DP HPD status notify. However,
> they all had various problems and it was difficult to become a common
> solution.
> 
> Under Dmitry's guidance, I try to add default DRM AUX HPD device when
> register DisplayPort altmode in patch 1. That makes it redundant for
> each Type-C chip driver to implement a similar registration process
> in embedded scenarios.
> 
> ====
> 2. Altmode switching and orientation switching for USBDP PHY
> 
> For USB Type-C interfaces, an external Type-C controller chip assists
> by detecting cable attachment, determining plug orientation, and
> reporting USB PD message. The USB/DP combo PHY supports software
> configurable pin mapping and DisplayPort lane assignment. Based on
> these message, the combo PHY can perform both altmode switching and
> orientation switching via software.
> 
> The RK3399 EVB IND board has a Type-C interface DisplayPort. It use
> fusb302 chip as Type-C controller. The connection diagram is shown below:
> 
> fusb302 chip +---> USB2.0 PHY ----> DWC3 USB controller
>              |
>              +---> USB/DP PHY0 +--> CDN-DP controller
>                                |
>                                +--> DWC3 USB controller
> 
> ====
> 3. Multiple bridge model for RK3399 CDN-DP
> 
> The RK3399 has two USB/DP combo PHY and one CDN-DP controller. And
> the CDN-DP can be switched to output to one of the PHYs.
> 
> USB/DP PHY0 ---+
>                | <----> CDN-DP controller
> USB/DP PHY1 ---+
> 
> In previous versions, if both PHY ports were connected to DP,
> the CDN-DP driver would select the first PHY port for output.
> 
> On Dmitry's suggestion, we introduced a multi-bridge model to support
> flexible selection of the output PHY port. For each PHY port, a
> separate encoder and bridge are registered.
> 
> The change is based on the DRM AUX HPD bridge, rather than the
> extcon approach. This requires the DT to correctly describe the
> connections between the first bridge in bridge chain and DP
> controller. And Once the first bridge is obtained, we can get the
> last bridge corresponding to the USB-C connector, and then set the
> DRM connector's fwnode to the corresponding one to enable HPD
> notification.
> 
> ====
> Patch1 add default HPD device when register Displayport altmode.
> Patch2 add new Type-C mode switch for RK3399 USBDP phy binding.
> Patch3 add typec_mux and typec_switch for RK3399 USBDP PHY.
> Patch4 add DRM AUX bridge support for RK3399 USBDP PHY.
> Patch5 drops CDN-DP's extcon dependency when Type-C is present.
> Patch6 add multiple bridges to support PHY port selection.
> Patch7 add missing dp_out port for RK3399 CDN-DP.
> Patch8 add Type-C DP support for RK3399 EVB IND board.
> 
> Changes in v6:
> - Link to V5: https://lore.kernel.org/all/20251011033233.97-1-kernel@airkyi.com/
> - Fix depend in Kconfig.
> - Check DP svid in tcphy_typec_mux_set().
> - Remove mode setting in tcphy_orien_sw_set().
> - Rename some variable names.
> - Attach the DP bridge to the next bridge.
> 
> Changes in v5:
> - Link to V4: https://lore.kernel.org/all/20250922012039.323-1-kernel@airkyi.com/
> - Remove the calls related to `drm_aux_hpd_bridge_notify()`.
> - Place the helper functions in the same compilation unit.
> - Add more comments about parent device.
> - Add DRM AUX bridge support for RK3399 USBDP PHY
> - By parsing the HPD bridge chain, set the connector's of_node to the
> of_node corresponding to the USB-C connector.
> - Return EDID cache when other port is already enabled.
> 
> Changes in v4:
> - Link to V3: https://lore.kernel.org/all/20250729090032.97-1-kernel@airkyi.com/
> - Add default HPD device for DisplayPort altmode.
> - Introduce multiple bridges for CDN-DP.
> - ...
> 
> Changes in v3:
> - Link to V2: https://lore.kernel.org/all/20250718062619.99-1-kernel@airkyi.com/
> - Add more descriptions to clarify the role of the PHY in switching.
> - Fix wrong vdo value.
> - Fix port node in usb-c-connector.
> 
> Changes in v2:
> - Link to V1: https://lore.kernel.org/all/20250715112456.101-1-kernel@airkyi.com/
> - Reuse dp-port/usb3-port in rk3399-typec-phy binding.
> - Fix compile error when CONFIG_TYPEC is not enabled.
> - Notify DP HPD state by USB/DP PHY.
> - Ignore duplicate HPD events.
> - Add endpoint to link DP PHY and DP controller.
> - Fix devicetree coding style.
> 
> Chaoyi Chen (8):
>   usb: typec: Add default HPD device when register DisplayPort altmode
>   dt-bindings: phy: rockchip: rk3399-typec-phy: Support mode-switch
>   phy: rockchip: phy-rockchip-typec: Add typec_mux/typec_switch support
>   phy: rockchip: phy-rockchip-typec: Add DRM AUX bridge
>   drm/rockchip: cdn-dp: Support handle lane info without extcon
>   drm/rockchip: cdn-dp: Add multiple bridges to support PHY port
>     selection
>   arm64: dts: rockchip: Add missing dp_out port for RK3399 CDN-DP
>   arm64: dts: rockchip: rk3399-evb-ind: Add support for DisplayPort
> 
>  .../phy/rockchip,rk3399-typec-phy.yaml        |   6 +
>  arch/arm64/boot/dts/rockchip/rk3399-base.dtsi |  10 +-
>  .../boot/dts/rockchip/rk3399-evb-ind.dts      | 146 ++++++
>  drivers/gpu/drm/rockchip/cdn-dp-core.c        | 354 ++++++++++++---
>  drivers/gpu/drm/rockchip/cdn-dp-core.h        |  24 +-
>  drivers/phy/rockchip/Kconfig                  |   3 +
>  drivers/phy/rockchip/phy-rockchip-typec.c     | 420 +++++++++++++++++-
>  drivers/usb/typec/Kconfig                     |   2 +
>  drivers/usb/typec/class.c                     |  26 ++
>  include/linux/usb/typec_altmode.h             |   2 +
>  10 files changed, 911 insertions(+), 82 deletions(-)
> 
> --
> 2.49.0
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: attempting to guess base-commit...
 Base: tags/v6.18-rc1-18-g924aa1d9e0ae (exact match)
 Base: tags/v6.18-rc1-18-g924aa1d9e0ae (use --merge-base to override)

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/rockchip/' for 20251016022741.91-1-kernel@airkyi.com:

arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dtb: syscon@ff770000 (rockchip,rk3399-grf): usb2phy@e450: 'port' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/soc/rockchip/grf.yaml#
arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dtb: syscon@ff770000 (rockchip,rk3399-grf): usb2phy@e450: Unevaluated properties are not allowed ('port' was unexpected)
	from schema $id: http://devicetree.org/schemas/soc/rockchip/grf.yaml#
arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dtb: usb2phy@e450 (rockchip,rk3399-usb2phy): 'port' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/phy/rockchip,inno-usb2phy.yaml#
arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dtb: /sound: failed to match any schema with compatible: ['rockchip,rk3399-gru-sound']