From: Chen-Yu Tsai <wens@kernel.org>
To: Chen-Yu Tsai <wens@kernel.org>,
Jernej Skrabec <jernej@kernel.org>,
Samuel Holland <samuel@sholland.org>,
Mark Brown <broonie@kernel.org>, Stephen Boyd <sboyd@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Vinod Koul <vkoul@kernel.org>
Cc: linux-sunxi@lists.linux.dev, linux-sound@vger.kernel.org,
linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
devicetree@vger.kernel.org, dmaengine@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 08/11] arm64: dts: allwinner: a523: Add device node for SPDIF block
Date: Tue, 21 Oct 2025 01:10:54 +0800 [thread overview]
Message-ID: <20251020171059.2786070-9-wens@kernel.org> (raw)
In-Reply-To: <20251020171059.2786070-1-wens@kernel.org>
The A523 has a SPDIF interface that is capable of both playback and
capture.
Add a node for it.
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
---
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
index 8edbd3873199..33f991dbd00b 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
@@ -818,6 +818,21 @@ mcu_ccu: clock-controller@7102000 {
#reset-cells = <1>;
};
+ spdif: spdif@7116000 {
+ compatible = "allwinner,sun55i-a523-spdif";
+ reg = <0x07116000 0x400>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mcu_ccu CLK_BUS_MCU_SPDIF>,
+ <&mcu_ccu CLK_MCU_SPDIF_TX>,
+ <&mcu_ccu CLK_MCU_SPDIF_RX>;
+ clock-names = "apb", "tx", "rx";
+ resets = <&mcu_ccu RST_BUS_MCU_SPDIF>;
+ dmas = <&mcu_dma 2>, <&mcu_dma 2>;
+ dma-names = "rx", "tx";
+ #sound-dai-cells = <0>;
+ status = "disabled";
+ };
+
mcu_dma: dma-controller@7121000 {
compatible = "allwinner,sun55i-a523-mcu-dma",
"allwinner,sun50i-a100-dma";
--
2.47.3
next prev parent reply other threads:[~2025-10-20 17:11 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-20 17:10 [PATCH 00/11] allwinner: a523: Enable I2S and SPDIF TX Chen-Yu Tsai
2025-10-20 17:10 ` [PATCH 01/11] dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatibles for A523 Chen-Yu Tsai
2025-10-20 17:37 ` Conor Dooley
2025-10-20 17:10 ` [PATCH 02/11] ASoC: dt-bindings: allwinner,sun4i-a10-i2s: Add compatible " Chen-Yu Tsai
2025-10-20 17:38 ` Conor Dooley
2025-10-20 17:10 ` [PATCH 03/11] ASoC: dt-bindings: allwinner,sun4i-a10-spdif: " Chen-Yu Tsai
2025-10-20 17:38 ` Conor Dooley
2025-10-20 17:10 ` [PATCH 04/11] ASoC: sun4i-spdif: Support SPDIF output on A523 family Chen-Yu Tsai
2025-10-20 17:49 ` Jernej Škrabec
2025-10-21 3:50 ` Chen-Yu Tsai
2025-10-21 12:55 ` kernel test robot
2025-10-20 17:10 ` [PATCH 05/11] clk: sunxi-ng: sun55i-a523-r-ccu: Mark bus-r-dma as critical Chen-Yu Tsai
2025-10-20 17:51 ` Jernej Škrabec
2025-10-20 17:10 ` [PATCH 06/11] clk: sunxi-ng: sun55i-a523-ccu: Lower audio0 pll minimum rate Chen-Yu Tsai
2025-10-20 17:52 ` Jernej Škrabec
2025-10-20 18:09 ` Chen-Yu Tsai
2025-10-20 18:22 ` Jernej Škrabec
2025-10-20 17:10 ` [PATCH 07/11] arm64: dts: allwinner: a523: Add DMA controller device nodes Chen-Yu Tsai
2025-10-20 17:57 ` Jernej Škrabec
2025-10-20 17:10 ` Chen-Yu Tsai [this message]
2025-10-20 17:58 ` [PATCH 08/11] arm64: dts: allwinner: a523: Add device node for SPDIF block Jernej Škrabec
2025-10-20 17:10 ` [PATCH 09/11] arm64: dts: allwinner: a523: Add device nodes for I2S controllers Chen-Yu Tsai
2025-10-20 17:59 ` Jernej Škrabec
2025-10-20 17:10 ` [PATCH 10/11] arm64: dts: allwinner: a523: Add I2S2 pins on PI pin group Chen-Yu Tsai
2025-10-20 18:00 ` Jernej Škrabec
2025-10-20 17:10 ` [PATCH 11/11] [EXAMPLE] arm64: dts: allwinner: a527-cubie-a5e: Enable I2S and SPDIF output Chen-Yu Tsai
2025-10-21 21:14 ` kernel test robot
2025-10-22 19:07 ` (subset) [PATCH 00/11] allwinner: a523: Enable I2S and SPDIF TX Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251020171059.2786070-9-wens@kernel.org \
--to=wens@kernel.org \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=jernej@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sound@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=robh@kernel.org \
--cc=samuel@sholland.org \
--cc=sboyd@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).