devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: E Shattow <e@freeshell.de>
To: Conor Dooley <conor@kernel.org>,
	Emil Renner Berthing <kernel@esmil.dk>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Paul Walmsley <pjw@kernel.org>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Albert Ou <aou@eecs.berkeley.edu>,
	Alexandre Ghiti <alex@ghiti.fr>
Cc: linux-kernel@vger.kernel.org, linux-riscv@lists.infradead.org,
	devicetree@vger.kernel.org, E Shattow <e@freeshell.de>,
	Icenowy Zheng <uwu@icenowy.me>,
	Conor Dooley <conor+dt@kernel.org>
Subject: [PATCH v3 2/2] riscv: dts: starfive: add Orange Pi RV
Date: Sun, 23 Nov 2025 14:50:45 -0800	[thread overview]
Message-ID: <20251123225059.49665-3-e@freeshell.de> (raw)
In-Reply-To: <20251123225059.49665-1-e@freeshell.de>

From: Icenowy Zheng <uwu@icenowy.me>

Orange Pi RV is a SBC based on the StarFive VisionFive 2 board.

Orange Pi RV features:

- StarFive JH7110 SoC
- GbE port connected to JH7110 GMAC0 via YT8531 PHY
- 4x USB ports via VL805 PCIe USB controller connected to JH7110 pcie0
- M.2 M-key slot connected to JH7110 pcie1
- HDMI video output
- 3.5mm audio output
- Ampak AP6256 SDIO Wi-Fi/Bluetooth module on mmc0
- microSD slot on mmc1
- SPI NOR flash memory
- 24c02 EEPROM (read only by default)

Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: E Shattow <e@freeshell.de>
---
 arch/riscv/boot/dts/starfive/Makefile         |  1 +
 .../boot/dts/starfive/jh7110-orangepi-rv.dts  | 76 +++++++++++++++++++
 2 files changed, 77 insertions(+)
 create mode 100644 arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts

diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
index 62b659f89ba7..d34c8c79bc10 100644
--- a/arch/riscv/boot/dts/starfive/Makefile
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-emmc.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-lite.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-orangepi-rv.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
diff --git a/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
new file mode 100644
index 000000000000..16ec2767134e
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "jh7110-common.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi RV";
+	compatible = "xunlong,orangepi-rv", "starfive,jh7110";
+
+	/* This regulator is always on by hardware */
+	reg_vcc3v3_pcie: regulator-vcc3v3-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3-pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&sysgpio 62 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gmac0 {
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+	starfive,tx-use-rgmii-clk;
+	status = "okay";
+};
+
+&mmc0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cap-sd-highspeed;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	vmmc-supply = <&reg_vcc3v3_pcie>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+
+	ap6256: wifi@1 {
+		compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+		/* TODO: out-of-band IRQ on GPIO21 */
+	};
+};
+
+&mmc1 {
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&phy0 {
+	rx-internal-delay-ps = <1500>;
+	tx-internal-delay-ps = <1500>;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-10-inverted;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+};
+
+&pwmdac {
+	status = "okay";
+};
-- 
2.50.0


  parent reply	other threads:[~2025-11-23 22:53 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-11-23 22:50 [PATCH v3 0/2] riscv: dts: starfive: Add OrangePi RV board E Shattow
2025-11-23 22:50 ` [PATCH v3 1/2] dt-bindings: riscv: starfive: add xunlong,orangepi-rv E Shattow
2025-11-24  7:28   ` Krzysztof Kozlowski
2025-11-24 13:22     ` Conor Dooley
2025-11-24 21:59       ` E Shattow
2025-11-25  7:28         ` Krzysztof Kozlowski
2025-11-25  7:33           ` Icenowy Zheng
2025-11-25  7:48             ` Krzysztof Kozlowski
2025-11-25  8:01               ` Icenowy Zheng
2025-11-25 13:07                 ` E Shattow
2025-11-25 19:14                   ` Conor Dooley
2025-11-26 20:34                     ` E Shattow
2025-11-26  8:23                   ` Krzysztof Kozlowski
2025-11-23 22:50 ` E Shattow [this message]
2025-11-24 11:07   ` [PATCH v3 2/2] riscv: dts: starfive: add Orange Pi RV Conor Dooley
2025-11-24 11:08     ` Icenowy Zheng
2025-11-24 13:21       ` Conor Dooley
2025-11-24 21:56         ` E Shattow
2025-11-25 22:24 ` [PATCH v3 0/2] riscv: dts: starfive: Add OrangePi RV board Conor Dooley
2025-11-26 13:48   ` Emil Renner Berthing

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20251123225059.49665-3-e@freeshell.de \
    --to=e@freeshell.de \
    --cc=alex@ghiti.fr \
    --cc=aou@eecs.berkeley.edu \
    --cc=conor+dt@kernel.org \
    --cc=conor@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kernel@esmil.dk \
    --cc=krzk+dt@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=palmer@dabbelt.com \
    --cc=pjw@kernel.org \
    --cc=robh@kernel.org \
    --cc=uwu@icenowy.me \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).