[PATCH v2 3/3] riscv: dts: spacemit: Enable USB3.0 on BananaPi-F3

[Ze Huang <huang.ze@linux.dev>]

Enable the DWC3 USB 3.0 controller and its associated usbphy2 on the
Banana Pi F3 board.

The board utilizes a VLI VL817 hub, which requires two separate power
supplies: one VBUS and one for hub itself. Add two GPIO-controlled
fixed-regulators to manage this.

Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ze Huang <huang.ze@linux.dev>
---
 arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 48 +++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index 3f10efd925dc..013df91c6a4c 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -59,6 +59,26 @@ reg_vcc_4v: vcc-4v {
 		regulator-always-on;
 		vin-supply = <&reg_dc_in>;
 	};
+
+	usb3_vbus: regulator-vbus-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "USB30_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		gpio = <&gpio K1_GPIO(97) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usb3_vhub: regulator-vhub-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "USB30_VHUB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		gpio = <&gpio K1_GPIO(123) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &combo_phy {
@@ -67,6 +87,34 @@ &combo_phy {
 	status = "okay";
 };
 
+&usbphy2 {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "host";
+	vbus-supply = <&usb3_vbus>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	hub_2_0: hub@1 {
+		compatible = "usb2109,2817";
+		reg = <0x1>;
+		vdd-supply = <&usb3_vhub>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio K1_GPIO(124) GPIO_ACTIVE_LOW>;
+	};
+
+	hub_3_0: hub@2 {
+		compatible = "usb2109,817";
+		reg = <0x2>;
+		vdd-supply = <&usb3_vhub>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio K1_GPIO(124) GPIO_ACTIVE_LOW>;
+	};
+};
+
 &emmc {
 	bus-width = <8>;
 	mmc-hs400-1_8v;

-- 
2.52.0