From: Richard Acayan <mailingradian@gmail.com>
To: Mauro Carvalho Chehab <mchehab@kernel.org>,
Rob Herring <robh@kernel.org>, Conor Dooley <conor+dt@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Sakari Ailus <sakari.ailus@linux.intel.com>,
Tianshu Qiu <tian.shu.qiu@intel.com>,
linux-media@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-msm@vger.kernel.org
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>,
Robert Mader <robert.mader@collabora.com>,
Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>,
David Heidelberg <david@ixit.cz>,
phone-devel@vger.kernel.org,
Richard Acayan <mailingradian@gmail.com>
Subject: [PATCH v5 0/5] media: i2c: IMX355 for the Pixel 3a
Date: Tue, 6 Jan 2026 23:24:46 -0500 [thread overview]
Message-ID: <20260107042451.92048-1-mailingradian@gmail.com> (raw)
This adds support for the IMX355 in devicetree and adds support for the
Pixel 3a front camera.
Changes since v4 (https://lore.kernel.org/r/20251211014846.16602-1-mailingradian@gmail.com):
- add NAK from Krzysztof (2/5)
- label the camss ports (3/5, 5/5)
- define endpoint properties correctly (1/5)
- use devm_regulator_bulk_get_const (2/5)
- remove clock-names (1/5, 5/5)
- set reset GPIO as active low (1/5, 2/5, 5/5)
- explicitly drive reset low at start of sequence (2/5)
- make data-lanes in endpoint optional and start at 1 (1/5, 5/5)
- add mclk3 pin (4/5)
- add Reviewed-by's (4/5)
Changes since v3 (https://lore.kernel.org/r/20250905215516.289998-6-mailingradian@gmail.com):
- separate camera mclk pins and move to different patch (4/5, 5/5)
- remove polarity from rear camera pin (5/5)
- remove output-low from front camera pins (5/5)
- mention effects of dcf6fb89e6f7 ("media: qcom: camss: remove a check for unavailable CAMSS endpoint") (3/5)
- specify single clock-name without items nesting (1/5)
- rebase on 49c6ac166cf7 ("media: i2c: imx355: Replace client->dev
usage") and eaa7d46d9654 ("media: i2c: imx335: Use V4L2 sensor clock
helper") (2/5)
- do not use of_match_ptr for OF match table (2/5)
- remove redundant GPIO validity checks (2/5)
- describe endpoint data-lanes (1/5)
Changes since v2 (https://lore.kernel.org/r/20250714210227.714841-6-mailingradian@gmail.com):
- use devm_v4l2_sensor_clk_get (2/4)
- require supplies and clock-names (1/4)
- move unevaluatedProperties down (1/4)
- disable clocks as last power-off action (2/4)
- use 0 in gpio pin power-supply (4/4)
Changes since v1 (https://lore.kernel.org/r/20250630225944.320755-7-mailingradian@gmail.com):
- too much to have a complete list (1-4/4)
- squash camera orientation patch (4/4, previously 5/5)
- squash driver changes (2/4, previously 3/5)
- remove labelled endpoint node in sdm670.dtsi (3/4, 4/4)
- change init sequence to match other similar drivers (2/4)
- retrieve clock frequency from devicetree-defined clock (4/4)
- remove clock-frequency from dt-bindings (1/4)
- remove redundant descriptions of child nodes (1/4)
- switch initial drive of the reset GPIO to low (2/4)
- set mclk frequency to 19.2 MHz (4/4)
- add vdda-pll supply for camss (4/4)
- use common power on and off functions (2/4)
- use devm_clk_get_optional (2/4)
- remove extra layer when describing mclk pin (4/4)
- rename regulators (1/4, 2/4, 4/4)
Richard Acayan (5):
dt-bindings: media: i2c: Add Sony IMX355
media: i2c: imx355: Support devicetree and power management
arm64: dts: qcom: sdm670: label the camss ports instead of endpoints
arm64: dts: qcom: sdm670: add camera mclk pins
arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera
.../bindings/media/i2c/sony,imx355.yaml | 115 +++++++++++++++++
.../boot/dts/qcom/sdm670-google-sargo.dts | 104 ++++++++++++++++
arch/arm64/boot/dts/qcom/sdm670.dtsi | 46 ++++---
drivers/media/i2c/imx355.c | 116 ++++++++++++++++--
4 files changed, 358 insertions(+), 23 deletions(-)
create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml
--
2.52.0
next reply other threads:[~2026-01-07 4:24 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-07 4:24 Richard Acayan [this message]
2026-01-07 4:28 ` [PATCH v5 0/5] media: i2c: IMX355 for the Pixel 3a Richard Acayan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260107042451.92048-1-mailingradian@gmail.com \
--to=mailingradian@gmail.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=david@ixit.cz \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=phone-devel@vger.kernel.org \
--cc=robert.mader@collabora.com \
--cc=robh@kernel.org \
--cc=sakari.ailus@linux.intel.com \
--cc=tian.shu.qiu@intel.com \
--cc=vladimir.zapolskiy@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox