* [PATCH v8 1/8] ARM: dts: twl6032: Add DTS file for TWL6032 PMIC
2026-02-23 13:49 Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 2/8] dt-bindings: vendor-prefixes: Add Doestek Mithil Bavishi
` (7 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap
Add a dedicated DTS file for the TWL6032 PMIC (Phoenix Lite). Already
has driver support with TWL6030 (Phoenix) since both of them are so
similar, some nodes can be reused from TWL6030 as well
This can be included in the board files like twl6030
Example:
...
&i2c1 {
twl: twl@48 {
reg = <0x48>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
interrupt-parent = <&gic>;
};
};
/include/ "twl6032.dtsi"
...
Used in devices like samsung-espresso, amazon-jem, epson-embt2ws etc
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
---
arch/arm/boot/dts/ti/omap/twl6032.dtsi | 77 ++++++++++++++++++++++++++
1 file changed, 77 insertions(+)
create mode 100644 arch/arm/boot/dts/ti/omap/twl6032.dtsi
diff --git a/arch/arm/boot/dts/ti/omap/twl6032.dtsi b/arch/arm/boot/dts/ti/omap/twl6032.dtsi
new file mode 100644
index 000000000..d599a2ca6
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/twl6032.dtsi
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Integrated Power Management Chip
+ * https://www.ti.com/lit/ds/symlink/twl6032.pdf
+ */
+
+&twl {
+ compatible = "ti,twl6032";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ rtc {
+ compatible = "ti,twl4030-rtc";
+ interrupts = <11>;
+ };
+
+ vio: regulator-vio {
+ compatible = "ti,twl6032-vio";
+ };
+
+ ldo1: regulator-ldo1 {
+ compatible = "ti,twl6032-ldo1";
+ };
+
+ ldo2: regulator-ldo2 {
+ compatible = "ti,twl6032-ldo2";
+ };
+
+ ldo3: regulator-ldo3 {
+ compatible = "ti,twl6032-ldo3";
+ };
+
+ ldo4: regulator-ldo4 {
+ compatible = "ti,twl6032-ldo4";
+ };
+
+ ldo5: regulator-ldo5 {
+ compatible = "ti,twl6032-ldo5";
+ };
+
+ ldo6: regulator-ldo6 {
+ compatible = "ti,twl6032-ldo6";
+ };
+
+ ldoln: regulator-ldoln {
+ compatible = "ti,twl6032-ldoln";
+ };
+
+ ldousb: regulator-ldousb {
+ compatible = "ti,twl6032-ldousb";
+ };
+
+ smps4: regulator-smps4 {
+ compatible = "ti,twl6032-smps4";
+ };
+
+ gpadc: gpadc {
+ compatible = "ti,twl6032-gpadc";
+ interrupts = <3>;
+ #io-channel-cells = <1>;
+ };
+
+ twl_usb_comparator: usb-comparator {
+ compatible = "ti,twl6030-usb";
+ interrupts = <4>, <10>;
+ };
+
+ twl_pwm: pwm {
+ compatible = "ti,twl6030-pwm";
+ #pwm-cells = <2>;
+ };
+
+ twl_pwmled: pwmled {
+ compatible = "ti,twl6030-pwmled";
+ #pwm-cells = <2>;
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v8 2/8] dt-bindings: vendor-prefixes: Add Doestek
2026-02-23 13:49 Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 1/8] ARM: dts: twl6032: Add DTS file for TWL6032 PMIC Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 3/8] dt-bindings: display: bridge: lvds-codec: add doestek,dtc34lm85am Mithil Bavishi
` (6 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap,
Krzysztof Kozlowski
Add vendor prefix for Doestek Co., Ltd.
Link: http://www.doestek.co.kr/
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index c7591b2ae..70a195fc6 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -437,6 +437,8 @@ patternProperties:
description: D-Link Corporation
"^dmo,.*":
description: Data Modul AG
+ "^doestek,.*":
+ description: Doestek Co., Ltd.
"^domintech,.*":
description: Domintech Co., Ltd.
"^dongwoon,.*":
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v8 3/8] dt-bindings: display: bridge: lvds-codec: add doestek,dtc34lm85am
2026-02-23 13:49 Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 1/8] ARM: dts: twl6032: Add DTS file for TWL6032 PMIC Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 2/8] dt-bindings: vendor-prefixes: Add Doestek Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-03-02 20:16 ` Andreas Kemnade
2026-02-23 13:49 ` [PATCH v8 4/8] dt-bindings: display: panel-lvds: Add compatibles for Samsung LTN070NL01 and LTN101AL03 panels Mithil Bavishi
` (5 subsequent siblings)
8 siblings, 1 reply; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap,
Krzysztof Kozlowski
Add compatible strings for the Doestek DTC34LM85AM Flat Panel Display
Transmitter
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
index 4f7d3e9cf..3ad01645c 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
@@ -33,6 +33,7 @@ properties:
oneOf:
- items:
- enum:
+ - doestek,dtc34lm85am # For the Doestek DTC34LM85AM Flat Panel Display (FPD) Transmitter
- ti,ds90c185 # For the TI DS90C185 FPD-Link Serializer
- ti,ds90c187 # For the TI DS90C187 FPD-Link Serializer
- ti,sn75lvds83 # For the TI SN75LVDS83 FlatLink transmitter
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v8 3/8] dt-bindings: display: bridge: lvds-codec: add doestek,dtc34lm85am
2026-02-23 13:49 ` [PATCH v8 3/8] dt-bindings: display: bridge: lvds-codec: add doestek,dtc34lm85am Mithil Bavishi
@ 2026-03-02 20:16 ` Andreas Kemnade
0 siblings, 0 replies; 13+ messages in thread
From: Andreas Kemnade @ 2026-03-02 20:16 UTC (permalink / raw)
To: Mithil Bavishi
Cc: aaro.koskinen, airlied, conor+dt, jernej.skrabec, jonas, khilman,
krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, devicetree, dri-devel, linux-kernel, linux-omap,
Krzysztof Kozlowski
On Mon, 23 Feb 2026 08:49:35 -0500
Mithil Bavishi <bavishimithil@gmail.com> wrote:
> Add compatible strings for the Doestek DTC34LM85AM Flat Panel Display
> Transmitter
>
> Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
does not apply anymore. Trivial rebase is needed.
Regards,
Andreas
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v8 4/8] dt-bindings: display: panel-lvds: Add compatibles for Samsung LTN070NL01 and LTN101AL03 panels
2026-02-23 13:49 Mithil Bavishi
` (2 preceding siblings ...)
2026-02-23 13:49 ` [PATCH v8 3/8] dt-bindings: display: bridge: lvds-codec: add doestek,dtc34lm85am Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 5/8] ARM: dts: ti: omap: espresso-common: Add common device tree for Samsung Galaxy Tab 2 series Mithil Bavishi
` (4 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap,
Krzysztof Kozlowski
The LTN070NL01 is a 7.0 inch 1024x600, 24 bit, VESA Compatible, TFT
display panel
The LTN101AL03 is a 10.1 inch 800x1280, 24 bit, VESA Compatible, TFT
display panel
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../devicetree/bindings/display/panel/panel-lvds.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml b/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml
index dbc01e640..b31c67bab 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml
@@ -58,6 +58,10 @@ properties:
- hydis,hv070wx2-1e0
# Jenson Display BL-JT60050-01A 7" WSVGA (1024x600) color TFT LCD LVDS panel
- jenson,bl-jt60050-01a
+ # Samsung LTN070NL01 7.0" WSVGA (1024x600) TFT LCD LVDS panel
+ - samsung,ltn070nl01
+ # Samsung LTN101AL03 10.1" WXGA (800x1280) TFT LCD LVDS panel
+ - samsung,ltn101al03
- tbs,a711-panel
# Winstar WF70A8SYJHLNGA 7" WSVGA (1024x600) color TFT LCD LVDS panel
- winstar,wf70a8syjhlnga
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v8 5/8] ARM: dts: ti: omap: espresso-common: Add common device tree for Samsung Galaxy Tab 2 series
2026-02-23 13:49 Mithil Bavishi
` (3 preceding siblings ...)
2026-02-23 13:49 ` [PATCH v8 4/8] dt-bindings: display: panel-lvds: Add compatibles for Samsung LTN070NL01 and LTN101AL03 panels Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-03-02 19:58 ` Andreas Kemnade
2026-02-23 13:49 ` [PATCH v8 6/8] dt-bindings: omap: Add Samsung Galaxy Tab 2 7.0 and 10.1 Mithil Bavishi
` (3 subsequent siblings)
8 siblings, 1 reply; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap
Create common device tree for Samsung Espresso series devices
Create a shared device tree for all variants first.
Device-specific trees will be added later based on screen size.
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
---
.../omap/omap4-samsung-espresso-common.dtsi | 744 ++++++++++++++++++
1 file changed, 744 insertions(+)
create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi
diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi
new file mode 100644
index 000000000..1c40c6bb3
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi
@@ -0,0 +1,744 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/dts-v1/;
+#include "dt-bindings/gpio/gpio.h"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include "omap443x.dtsi"
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ continuous_splash: framebuffer@bef00000{
+ reg = <0xbef00000 (1024 * 600 * 4)>;
+ no-map;
+ };
+ };
+
+ chosen {
+ stdout-path = &uart3;
+ #address-cells = <1>;
+ };
+
+ i2c-gpio5 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+ sda-gpios = <&gpio4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* TODO: SMB136 Charger for 7" variant at 0x4d */
+ };
+
+ i2c-gpio6 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_pins>;
+ sda-gpios = <&gpio3 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* TODO: STMPE811 ADC at 0x41 */
+ };
+
+ i2c-gpio7 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_pins>;
+ sda-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fuel-gauge@36 {
+ compatible = "maxim,max17042";
+ reg = <0x36>;
+ pinctrl-0 = <&fuel_alert_irq>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio2>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+ maxim,rsns-microohm = <10000>;
+ maxim,over-heat-temp = <500>;
+ maxim,dead-volt = <2500>;
+ maxim,over-volt = <4300>;
+ };
+ };
+
+ reg_espresso_wlan: regulator-espresso-wlan {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlanen_gpio>;
+ compatible = "regulator-fixed";
+ regulator-name = "espresso_wlan";
+ regulator-max-microvolt = <2000000>;
+ regulator-min-microvolt = <2000000>;
+ gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */
+ startup-delay-us = <70000>;
+ regulator-always-on;
+ enable-active-high;
+ };
+
+ wlan_pwrseq: wlan-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&twl 0>;
+ clock-names = "ext_clock";
+ };
+
+ reg_espresso_internal: regulator-espresso-internal {
+ compatible = "regulator-fixed";
+ regulator-name = "eMMC_LDO";
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; /* GPIO_63 */
+ startup-delay-us = <100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ enable-active-high;
+ };
+
+ reg_espresso_external: regulator-espresso-external {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmc1";
+ regulator-max-microvolt = <2800000>;
+ regulator-min-microvolt = <2800000>;
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; /* GPIO_34 */
+ enable-active-high;
+ };
+
+ reg_touch_ldo_en: regulator-touch-ldo-en {
+ compatible = "regulator-fixed";
+ regulator-name = "touch_ldo_en";
+ regulator-max-microvolt = <2800000>;
+ regulator-min-microvolt = <2800000>;
+ gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* GPIO_54 */
+ regulator-always-on;
+ enable-active-high;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+
+ key-power {
+ label = "power";
+
+ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; /* GPIO_wk3 */
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ button-volup {
+ linux,code = <KEY_VOLUMEUP>;
+ label = "volume_up"; /* GPIO_wk30 */
+ gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ };
+
+ button-voldown {
+ linux,code = <KEY_VOLUMEDOWN>;
+ label = "volume_down"; /* GPIO_wk8 */
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_lcd: regulator-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_en";
+ gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO_135 */
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ pwm10: pwm-10 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm10_default>;
+ compatible = "ti,omap-dmtimer-pwm";
+ #pwm-cells = <3>;
+ ti,timers = <&timer10>;
+ ti,clock-source = <0x00>;
+ };
+
+ lvds-encoder {
+ compatible = "doestek,dtc34lm85am", "lvds-encoder";
+ powerdown-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; /* GPIO_136 */
+ power-supply = <®_lcd>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ bridge_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ bridge_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
+
+ vibrator {
+ compatible = "gpio-vibrator";
+ enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; /* GPIO_38 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&vibrator_default>;
+ };
+
+ gp2a_shunt: current-sense-shunt {
+ compatible = "current-sense-shunt";
+ io-channels = <&gpadc 4>;
+ shunt-resistor-micro-ohms = <24000000>; /* 24 ohms */
+ #io-channel-cells = <0>;
+ };
+
+ led-ir {
+ compatible = "gpio-ir-tx";
+ gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* GPIO_59 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ledir_pins>;
+ };
+};
+
+&omap4_pmx_wkup {
+ gpio_keys: gpio-keys-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x046, PIN_INPUT | MUX_MODE3)
+ /* sim_cd.gpio_wk3 - EXT_WAKEUP */
+ OMAP4_IOPAD(0x056, | PIN_INPUT | MUX_MODE3)
+ /* fref_clk3_req.gpio_wk30 - VOL_UP */
+ OMAP4_IOPAD(0x05C, | PIN_INPUT | MUX_MODE3)
+ /* fref_clk4_out.gpio_wk8 - VOL_DN */
+ >;
+ };
+};
+
+&omap4_pmx_core {
+ backlight_pins: pinmux-backlight-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0X0D8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3)
+ /* usbb1_ulpitll_dat7.gpio_95 - LED_BACKLIGHT_RESET */
+ >;
+ };
+
+ bluetooth_pins: pinmux-bluetooth-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
+ /* gpmc_ncs6.gpio_103 - BT_EN */
+ OMAP4_IOPAD(0x0be, PIN_OUTPUT | MUX_MODE3)
+ /* cam_strobe.gpio_82 - BT_nRST */
+ OMAP4_IOPAD(0x0c0, PIN_INPUT | MUX_MODE3)
+ /* cam_globalreset.gpio_83 - BT_HOST_WAKE */
+ OMAP4_IOPAD(0x0d4, PIN_OUTPUT | MUX_MODE3)
+ /* usbb1_ulpitll_dat5.gpio_93 - BT_WAKE */
+ >;
+ };
+
+ dss_dpi_pins: pinmux-dss-dpi-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x162, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data23 */
+ OMAP4_IOPAD(0x164, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data22 */
+ OMAP4_IOPAD(0x166, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data21 */
+ OMAP4_IOPAD(0x168, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data20 */
+ OMAP4_IOPAD(0x16a, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data19 */
+ OMAP4_IOPAD(0x16c, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data18 */
+ OMAP4_IOPAD(0x16e, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data15 */
+ OMAP4_IOPAD(0x170, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data14 */
+ OMAP4_IOPAD(0x172, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data13 */
+ OMAP4_IOPAD(0x174, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data12 */
+ OMAP4_IOPAD(0x176, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data11 */
+ OMAP4_IOPAD(0x1b4, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data10 */
+ OMAP4_IOPAD(0x1b6, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data9 */
+ OMAP4_IOPAD(0x1b8, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data16 */
+ OMAP4_IOPAD(0x1ba, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data17 */
+ OMAP4_IOPAD(0x1bc, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_hsync */
+ OMAP4_IOPAD(0x1be, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_pclk */
+ OMAP4_IOPAD(0x1c0, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_vsync */
+ OMAP4_IOPAD(0x1c2, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_de */
+ OMAP4_IOPAD(0x1c4, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data8 */
+ OMAP4_IOPAD(0x1c6, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data7 */
+ OMAP4_IOPAD(0x1c8, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data6 */
+ OMAP4_IOPAD(0x1ca, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data5 */
+ OMAP4_IOPAD(0x1cc, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data4 */
+ OMAP4_IOPAD(0x1ce, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data3 */
+
+ OMAP4_IOPAD(0x1d0, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data2 */
+ OMAP4_IOPAD(0x1d2, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data1 */
+ OMAP4_IOPAD(0x1d4, PIN_OFF_OUTPUT_LOW | MUX_MODE5)
+ /* dispc2_data0 */
+ >;
+ };
+
+ fuel_alert_irq: pinmux-fuel-alert-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* gpmc_a20.gpio_44 */
+ >;
+ };
+
+ i2c1_pins: pinmux-i2c1-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c1_scl */
+ OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c1_sda */
+ >;
+ };
+
+ i2c2_pins: pinmux-i2c2-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c2_scl */
+ OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c2_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux-i2c3-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c3_scl */
+ OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c3_sda */
+ >;
+ };
+
+ i2c4_pins: pinmux-i2c4-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c4_scl */
+ OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* i2c4_sda */
+ >;
+ };
+
+ i2c5_pins: pinmux-i2c5-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x0de, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* usbc1_icusb_dp.gpio_98 */
+ OMAP4_IOPAD(0x0e0, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* usbc1_icusb_dm.gpio_99 */
+ >;
+ };
+
+ i2c6_pins: pinmux-i2c6-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* hdmi_ddc_scl.gpio_65 */
+ OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* hdmi_ddc_sda.gpio_66 */
+ >;
+ };
+
+ i2c7_pins: pinmux-i2c7-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x08a, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* gpmc_wait0.gpio_61 */
+ OMAP4_IOPAD(0x08c, PIN_INPUT_PULLUP | MUX_MODE3)
+ /* gpmc_wait1.gpio_62 */
+ >;
+ };
+
+ ledir_pins: pimux-ledir-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x086, PIN_INPUT_PULLDOWN | MUX_MODE7)
+ /* gpmc_nbe0_cle.gpio_59 */
+ OMAP4_IOPAD(0x156, PIN_INPUT_PULLDOWN | MUX_MODE7)
+ /* mcspi4_simo.gpio_152 */
+ >;
+ };
+
+ lvds_pins: pinmux-lvds-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0X136, PIN_OUTPUT | MUX_MODE3)
+ /* mcspi1_simo.gpio_136 - LVDS_nSHDN */
+ >;
+ };
+
+ mmc1_pins: pinmux-mmc1-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLDOWN | MUX_MODE0)
+ /* sdmmc1_clk */
+ OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmcc1_cmd */
+ OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmcc1_dat0 */
+ OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc1_dat1 */
+ OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc1_dat2 */
+ OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc1_dat3 */
+ >;
+ };
+
+ mmc2_pins: pinmux-mmc2-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x040, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat0 */
+ OMAP4_IOPAD(0x042, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat1 */
+ OMAP4_IOPAD(0x044, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat2 */
+ OMAP4_IOPAD(0x046, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat3 */
+ OMAP4_IOPAD(0x048, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat4 */
+ OMAP4_IOPAD(0x04a, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat5 */
+ OMAP4_IOPAD(0x04c, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat6 */
+ OMAP4_IOPAD(0x04e, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_dat7 */
+ OMAP4_IOPAD(0x082, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_clk */
+ OMAP4_IOPAD(0x084, PIN_INPUT_PULLUP | MUX_MODE1)
+ /* sdmmc2_cmd */
+ >;
+ };
+
+ mmc5_pins: pinmux-mmc5-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x148, PIN_INPUT_PULLDOWN | MUX_MODE0)
+ /* sdmmc5_clk.sdmmc5_clk */
+ OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc5_cmd.sdmmc5_cmd */
+ OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc5_dat0.sdmmc5_dat0 */
+ OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc5_dat1.sdmmc5_dat1 */
+ OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc5_dat2.sdmmc5_dat2 */
+ OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* sdmmc5_dat3.sdmmc5_dat3 */
+ >;
+ };
+
+ pwm10_default: pinmux-pwm10-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0X0D6, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE1)
+ /* usbb1_ulpitll_dat6.dmtimer10_pwm_evt - LED_BACKLIGHT_PWM */
+ >;
+ };
+
+ touch_pins: pinmux-touch-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x06c, PIN_INPUT | MUX_MODE3)
+ /* gpmc_a22.gpio_46 - TSP_INT */
+ >;
+ };
+
+ uart2_pins: pinmux-uart2-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* uart2_cts.uart2_cts */
+ OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* uart2_rts.uart2_rts */
+ OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* uart2_rx.uart2_rx */
+ OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE0)
+ /* uart2_tx.uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux-uart3-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0)
+ /* uart3_rx_irrx */
+ OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0)
+ /* uart3_tx_irtx */
+ >;
+ };
+
+ vibrator_default: pinmux-vibrator-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x05c, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ /* gpmc_ad14.gpio_38 - MOTOR_EN */
+ >;
+ };
+
+ wlanen_gpio: pinmux-wlanen-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
+ /* gpmc_ncs7.gpio_104 */
+ >;
+ };
+
+ wlan_host_wake: pinmux-wlan-host-wake-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x0bc, PIN_INPUT | MUX_MODE3)
+ /* cam_shutter.gpio_81 - WLAN_HOST_WAKE */
+ >;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+
+ interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
+ &omap4_pmx_core OMAP4_UART3_RX>;
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+
+ twl: pmic@48 {
+ reg = <0x48>;
+ #clock-cells = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &twl6030_pins
+ &twl6030_wkup_pins
+ >;
+
+ /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
+ interrupt-parent = <&gic>;
+ system-power-controller;
+ };
+};
+
+#include "twl6032.dtsi"
+#include "twl6030_omap4.dtsi"
+
+&ldo1 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
+
+&ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
+
+&ldo4 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+};
+
+&ldo5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&ldo6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+};
+
+&smps4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&ldousb {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+
+ accelerometer@18 {
+ compatible = "bosch,bma254";
+ reg = <0x18>;
+ vdd-supply = <&ldo4>;
+ vddio-supply = <&ldo5>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <25 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>,
+ <26 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+ };
+
+ magnetometer@2e {
+ compatible = "yamaha,yas530";
+ reg = <0x2e>;
+ vdd-supply = <&ldo4>;
+ iovdd-supply = <&ldo5>;
+ reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+ interrupts = <&gpio6 10 IRQ_TYPE_EDGE_RISING>;
+ };
+
+ light-sensor@44 {
+ compatible = "sharp,gp2ap002a00f";
+ reg = <0x44>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&ldo4>;
+ vio-supply = <&ldo4>;
+ io-channels = <&gp2a_shunt>;
+ io-channel-names = "alsout";
+ sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
+ sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;
+ };
+};
+
+&dss {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ port {
+ dpi_out: endpoint {
+ remote-endpoint = <&bridge_in>;
+ data-lines = <24>;
+ };
+ };
+};
+
+&twl_usb_comparator {
+ usb-supply = <&ldousb>;
+};
+
+&usb_otg_hs {
+ interface-type = <1>;
+ mode = <3>;
+ power = <50>;
+};
+
+&mmc1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+
+ vmmc-supply = <®_espresso_external>;
+ bus-width = <4>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+
+ vmmc-supply = <®_espresso_internal>;
+ ti,non-removable;
+ bus-width = <8>;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mmc4 {
+ status = "disabled";
+};
+
+&mmc5 {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ non-removable;
+ bus-width = <4>;
+ vmmc-supply = <®_espresso_wlan>;
+ mmc-pwrseq = <&wlan_pwrseq>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc5_pins>;
+
+ brcmf: wifi@1 {
+ compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupt-parent = <&gpio3>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_host_wake>;
+ };
+};
+
+&uart2 {
+ interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
+ &omap4_pmx_core OMAP4_UART2_RX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ bluetooth {
+ compatible = "brcm,bcm4330-bt";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bluetooth_pins>;
+ shutdown-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
+ device-wakeup-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wakeup";
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v8 5/8] ARM: dts: ti: omap: espresso-common: Add common device tree for Samsung Galaxy Tab 2 series
2026-02-23 13:49 ` [PATCH v8 5/8] ARM: dts: ti: omap: espresso-common: Add common device tree for Samsung Galaxy Tab 2 series Mithil Bavishi
@ 2026-03-02 19:58 ` Andreas Kemnade
0 siblings, 0 replies; 13+ messages in thread
From: Andreas Kemnade @ 2026-03-02 19:58 UTC (permalink / raw)
To: Mithil Bavishi
Cc: aaro.koskinen, airlied, conor+dt, jernej.skrabec, jonas, khilman,
krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, devicetree, dri-devel, linux-kernel, linux-omap
On Mon, 23 Feb 2026 08:49:37 -0500
Mithil Bavishi <bavishimithil@gmail.com> wrote:
> Create common device tree for Samsung Espresso series devices
>
> Create a shared device tree for all variants first.
> Device-specific trees will be added later based on screen size.
>
> Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
[...]
> +&omap4_pmx_wkup {
> + gpio_keys: gpio-keys-pins {
> + pinctrl-single,pins = <
> + OMAP4_IOPAD(0x046, PIN_INPUT | MUX_MODE3)
> + /* sim_cd.gpio_wk3 - EXT_WAKEUP */
> + OMAP4_IOPAD(0x056, | PIN_INPUT | MUX_MODE3)
> + /* fref_clk3_req.gpio_wk30 - VOL_UP */
> + OMAP4_IOPAD(0x05C, | PIN_INPUT | MUX_MODE3)
syntax error. stray | in these two lines. even for small cosmetic
changes, at the very least build it.
Regards,
Andreas
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v8 6/8] dt-bindings: omap: Add Samsung Galaxy Tab 2 7.0 and 10.1
2026-02-23 13:49 Mithil Bavishi
` (4 preceding siblings ...)
2026-02-23 13:49 ` [PATCH v8 5/8] ARM: dts: ti: omap: espresso-common: Add common device tree for Samsung Galaxy Tab 2 series Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 7/8] ARM: dts: ti: omap: samsung-espresso7: Add initial support for Galaxy Tab 2 7.0 Mithil Bavishi
` (2 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap,
Krzysztof Kozlowski
Add samsung-espresso7 codename for the 7 inch variant
Add samsung-espresso10 codename for the 10 inch variant
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
---
Documentation/devicetree/bindings/arm/ti/omap.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/ti/omap.yaml b/Documentation/devicetree/bindings/arm/ti/omap.yaml
index 14f1b9d8f..f694dcbf2 100644
--- a/Documentation/devicetree/bindings/arm/ti/omap.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/omap.yaml
@@ -144,6 +144,8 @@ properties:
- motorola,droid-bionic # Motorola Droid Bionic XT875
- motorola,xyboard-mz609
- motorola,xyboard-mz617
+ - samsung,espresso7
+ - samsung,espresso10
- ti,omap4-panda
- ti,omap4-sdp
- const: ti,omap4430
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v8 7/8] ARM: dts: ti: omap: samsung-espresso7: Add initial support for Galaxy Tab 2 7.0
2026-02-23 13:49 Mithil Bavishi
` (5 preceding siblings ...)
2026-02-23 13:49 ` [PATCH v8 6/8] dt-bindings: omap: Add Samsung Galaxy Tab 2 7.0 and 10.1 Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-02-23 13:49 ` [PATCH v8 8/8] ARM: dts: ti: omap: samsung-espresso10: Add initial support for Galaxy Tab 2 10.1 Mithil Bavishi
2026-03-26 9:02 ` (subset) Neil Armstrong
8 siblings, 0 replies; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap
Create a device tree for the 7 inch variants (P3100, P3110, P3113)
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
---
arch/arm/boot/dts/ti/omap/Makefile | 1 +
.../dts/ti/omap/omap4-samsung-espresso7.dts | 70 +++++++++++++++++++
2 files changed, 71 insertions(+)
create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso7.dts
diff --git a/arch/arm/boot/dts/ti/omap/Makefile b/arch/arm/boot/dts/ti/omap/Makefile
index 14e500846..d24f13efd 100644
--- a/arch/arm/boot/dts/ti/omap/Makefile
+++ b/arch/arm/boot/dts/ti/omap/Makefile
@@ -80,6 +80,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
omap4-sdp-es23plus.dtb \
omap4-var-dvk-om44.dtb \
omap4-var-stk-om44.dtb \
+ omap4-samsung-espresso7.dtb \
omap4-xyboard-mz609.dtb \
omap4-xyboard-mz617.dtb
dtb-$(CONFIG_SOC_AM33XX) += \
diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso7.dts b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso7.dts
new file mode 100644
index 000000000..cae37ff06
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso7.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/dts-v1/;
+
+#include "omap4-samsung-espresso-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy Tab 2 (7 inch)";
+ compatible = "samsung,espresso7", "ti,omap4430", "ti,omap4";
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_pins>;
+ pwms = <&pwm10 0 1200 0>;
+ power-supply = <®_lcd>;
+ enable-gpios = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <2>;
+ };
+
+ panel {
+ compatible = "samsung,ltn070nl01", "panel-lvds";
+ power-supply = <®_lcd>;
+ width-mm = <154>;
+ height-mm = <90>;
+ data-mapping = "vesa-24";
+ backlight = <&backlight>;
+
+ panel-timing {
+ clock-frequency = <47255554>;
+
+ hback-porch = <210>;
+ hactive = <1024>;
+ hfront-porch = <186>;
+ hsync-len = <50>;
+
+ vback-porch = <11>;
+ vactive = <600>;
+ vfront-porch = <24>;
+ vsync-len = <10>;
+
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ syncclk-active = <0>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&bridge_out>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ touchscreen@48 {
+ compatible = "melfas,mms136";
+ reg = <0x48>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <1024>;
+ touchscreen-size-y = <600>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pins>;
+ avdd-supply = <®_touch_ldo_en>;
+ vdd-supply = <&ldo6>;
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v8 8/8] ARM: dts: ti: omap: samsung-espresso10: Add initial support for Galaxy Tab 2 10.1
2026-02-23 13:49 Mithil Bavishi
` (6 preceding siblings ...)
2026-02-23 13:49 ` [PATCH v8 7/8] ARM: dts: ti: omap: samsung-espresso7: Add initial support for Galaxy Tab 2 7.0 Mithil Bavishi
@ 2026-02-23 13:49 ` Mithil Bavishi
2026-03-02 19:52 ` Andreas Kemnade
2026-03-26 9:02 ` (subset) Neil Armstrong
8 siblings, 1 reply; 13+ messages in thread
From: Mithil Bavishi @ 2026-02-23 13:49 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, bavishimithil
Cc: devicetree, dri-devel, linux-kernel, linux-omap
Create a device tree for the 10 inch variants (P5100, P5110, P5113)
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
---
arch/arm/boot/dts/ti/omap/Makefile | 1 +
.../dts/ti/omap/omap4-samsung-espresso10.dts | 104 ++++++++++++++++++
2 files changed, 105 insertions(+)
create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
diff --git a/arch/arm/boot/dts/ti/omap/Makefile b/arch/arm/boot/dts/ti/omap/Makefile
index d24f13efd..140ac39b3 100644
--- a/arch/arm/boot/dts/ti/omap/Makefile
+++ b/arch/arm/boot/dts/ti/omap/Makefile
@@ -81,6 +81,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
omap4-var-dvk-om44.dtb \
omap4-var-stk-om44.dtb \
omap4-samsung-espresso7.dtb \
+ omap4-samsung-espresso10.dtb \
omap4-xyboard-mz609.dtb \
omap4-xyboard-mz617.dtb
dtb-$(CONFIG_SOC_AM33XX) += \
diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
new file mode 100644
index 000000000..5c00d67ac
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/dts-v1/;
+
+#include "omap4-samsung-espresso-common.dtsi"
+#include <dt-bindings/power/summit,smb347-charger.h>
+/ {
+ model = "Samsung Galaxy Tab 2 (10 inch)";
+ compatible = "samsung,espresso10", "ti,omap4430", "ti,omap4";
+
+ i2c-gpio5 {
+ smb347: charger@6 {
+ compatible = "summit,smb347";
+ reg = <0x6>; // 0x0C >> 1
+ interrupt-parent = <&gpio2>;
+ interrupts = <0 IRQ_TYPE_EDGE_BOTH>;
+
+ summit,enable-usb-charging;
+ summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
+ summit,chip-temperature-threshold-celsius = <120>;
+ summit,usb-current-limit-microamp = <1800000>;
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_pins>;
+ pwms = <&pwm10 0 1600 0>;
+ power-supply = <®_lcd>;
+ enable-gpios = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ };
+
+ panel {
+ compatible = "samsung,ltn101al03", "panel-lvds";
+ power-supply = <®_lcd>;
+ width-mm = <223>;
+ height-mm = <125>;
+ data-mapping = "vesa-24";
+ backlight = <&backlight>;
+
+ panel-timing {
+ clock-frequency = <69818000>;
+
+ hback-porch = <64>;
+ hactive = <1280>;
+ hfront-porch = <16>;
+ hsync-len = <48>;
+
+ vback-porch = <11>;
+ vactive = <800>;
+ vfront-porch = <16>;
+ vsync-len = <3>;
+
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&bridge_out>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&gpio2>;
+ interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pins>;
+
+ //avdd-supply = <®_touch_ldo_en>;
+ vdd-supply = <&ldo6>;
+
+ syna,reset-delay-ms = <200>;
+ syna,startup-delay-ms = <200>;
+
+ touchscreen-size-x = <1280>;
+ touchscreen-size-y = <800>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f11@11 {
+ reg = <0x11>;
+ touchscreen-size-x = <1280>;
+ touchscreen-size-y = <800>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v8 8/8] ARM: dts: ti: omap: samsung-espresso10: Add initial support for Galaxy Tab 2 10.1
2026-02-23 13:49 ` [PATCH v8 8/8] ARM: dts: ti: omap: samsung-espresso10: Add initial support for Galaxy Tab 2 10.1 Mithil Bavishi
@ 2026-03-02 19:52 ` Andreas Kemnade
0 siblings, 0 replies; 13+ messages in thread
From: Andreas Kemnade @ 2026-03-02 19:52 UTC (permalink / raw)
To: Mithil Bavishi
Cc: aaro.koskinen, airlied, conor+dt, jernej.skrabec, jonas, khilman,
krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
neil.armstrong, prabhakar.mahadev-lad.rj, jesszhan0024, rfoss,
robh, rogerq, simona, thierry.reding, tony, tzimmermann,
andrzej.hajda, devicetree, dri-devel, linux-kernel, linux-omap
On Mon, 23 Feb 2026 08:49:40 -0500
Mithil Bavishi <bavishimithil@gmail.com> wrote:
> Create a device tree for the 10 inch variants (P5100, P5110, P5113)
>
> Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
> ---
> arch/arm/boot/dts/ti/omap/Makefile | 1 +
> .../dts/ti/omap/omap4-samsung-espresso10.dts | 104 ++++++++++++++++++
> 2 files changed, 105 insertions(+)
> create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
>
> diff --git a/arch/arm/boot/dts/ti/omap/Makefile b/arch/arm/boot/dts/ti/omap/Makefile
> index d24f13efd..140ac39b3 100644
> --- a/arch/arm/boot/dts/ti/omap/Makefile
> +++ b/arch/arm/boot/dts/ti/omap/Makefile
> @@ -81,6 +81,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
> omap4-var-dvk-om44.dtb \
> omap4-var-stk-om44.dtb \
> omap4-samsung-espresso7.dtb \
> + omap4-samsung-espresso10.dtb \
> omap4-xyboard-mz609.dtb \
> omap4-xyboard-mz617.dtb
> dtb-$(CONFIG_SOC_AM33XX) += \
> diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
> new file mode 100644
> index 000000000..5c00d67ac
> --- /dev/null
> +++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso10.dts
> @@ -0,0 +1,104 @@
[...]
> +&i2c3 {
> + touchscreen@20 {
> + compatible = "syna,rmi4-i2c";
> + reg = <0x20>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + interrupt-parent = <&gpio2>;
> + interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&touch_pins>;
> +
> + //avdd-supply = <®_touch_ldo_en>;
> + vdd-supply = <&ldo6>;
> +
> + syna,reset-delay-ms = <200>;
> + syna,startup-delay-ms = <200>;
> +
> + touchscreen-size-x = <1280>;
> + touchscreen-size-y = <800>;
> +
duplicated,
> + rmi4-f01@1 {
> + reg = <0x01>;
> + syna,nosleep-mode = <1>;
> + };
> +
> + rmi4-f11@11 {
> + reg = <0x11>;
> + touchscreen-size-x = <1280>;
> + touchscreen-size-y = <800>;
it is needed and accepted only here.
Regards,
Andreas
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: (subset)
2026-02-23 13:49 Mithil Bavishi
` (7 preceding siblings ...)
2026-02-23 13:49 ` [PATCH v8 8/8] ARM: dts: ti: omap: samsung-espresso10: Add initial support for Galaxy Tab 2 10.1 Mithil Bavishi
@ 2026-03-26 9:02 ` Neil Armstrong
8 siblings, 0 replies; 13+ messages in thread
From: Neil Armstrong @ 2026-03-26 9:02 UTC (permalink / raw)
To: aaro.koskinen, airlied, andreas, conor+dt, jernej.skrabec, jonas,
khilman, krzk+dt, laurent.pinchart, maarten.lankhorst, mripard,
prabhakar.mahadev-lad.rj, jesszhan0024, rfoss, robh, rogerq,
simona, thierry.reding, tony, tzimmermann, andrzej.hajda,
Mithil Bavishi
Cc: devicetree, dri-devel, linux-kernel, linux-omap
Hi,
On Mon, 23 Feb 2026 08:49:32 -0500, Mithil Bavishi wrote:
> Subject: [PATCH v7 0/8] Initial support for Samsung Galaxy Tab 2 series
>
> This series adds initial support for the Samsung Galaxy Tab 2
> (samsung-espresso7/10) series of devices. It adds support for 6 variants
> (P3100, P3110, P3113, P5100, P5110, P5113). Downstream categorised them
> based on 3G and WiFi, but since they use different panel, touch
> controllers, batteries, I decided to categorise them based on screen
> size as espresso7 and espresso10.
>
> [...]
Thanks, Applied to https://gitlab.freedesktop.org/drm/misc/kernel.git (drm-misc-next)
[2/8] dt-bindings: vendor-prefixes: Add Doestek
https://gitlab.freedesktop.org/drm/misc/kernel/-/commit/e1f4ecd21f04f766f2cad5cca806147f47553d2f
[3/8] dt-bindings: display: bridge: lvds-codec: add doestek,dtc34lm85am
https://gitlab.freedesktop.org/drm/misc/kernel/-/commit/0c74f4e8d7592122c9e2c7b6f0bbdd8fd51b7fb3
--
Neil
^ permalink raw reply [flat|nested] 13+ messages in thread