Re: [PATCH v2 3/3] arm64: dts: allwinner: h6: Add TaiqiCat (TQC) A01 support

[Jun Yan <jerrysteve1101@gmail.com>]

Hi,
> On Fri, 27 Feb 2026 23:58:00 +0800
> Jun Yan <jerrysteve1101@gmail.com> wrote:
> 
> Hi,
> 
> > TaiqiCat (TQC) A01 is a set-top box powered by an Allwinner H6 SoC,
> > equipped with an AXP305 PMIC, 1GB LPDDR3 RAM, 8GB eMMC, an AP6212
> > WiFi/BT combo module, one 100M Ethernet port, one USB 3.0 Type-A port,
> > one USB 2.0 Type-A port, one Micro USB port, HDMI, SPDIF, Micro-SD, and
> > infrared input.
> 
> Many thanks for sending this upstream, this looks very good overall,
> only some small things below...
>  
> > It was released by Ultrapower(UQSoft) as a blockchain-based terminal and is
> > now discontinued and no longer supported.
> > 
> >   https://web.archive.org/web/20190409213228/https://tq.ultrapower.com.cn/product.html
> > 
> > Hardware schematics are not available at this time; however, the
> > dts from the vendor firmware is provided for reference [1].
> > 
> > Based on the PCB silkscreen marking "AZW-KT02 2.0", the ODM/OEM
> > can be confirmed as AZW, and the overall hardware circuit design
> > is highly similar to the Beelink GS1.
> > 
> > Tested, works:
> > - debug UART
> > - status LED
> > - USB 3.0 Type-A port
> > - USB 2.0 Type-A port
> > - Micro USB port (Host)
> > - MicroSD
> > - eMMC
> > - WiFi/Bluetooth
> > - HDMI video output
> > 
> > Does not work:
> > - Ethernet (requires AC200 MFD/EPHY driver)
> > - HDMI audio
> > 
> > Untested:
> > - SPDIF
> > - IR receiver
> > 
> > [1] https://archive.org/download/tqc-a01-stock-fw/tqc-a01-stock-fw.dts
> > 
> > Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
> > ---
> >  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
> >  .../dts/allwinner/sun50i-h6-taiqicat-a01.dts  | 361 ++++++++++++++++++
> >  2 files changed, 362 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts
> > 
> > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> > index 2edfa7bf4ab3..d116864b6c2b 100644
> > --- a/arch/arm64/boot/dts/allwinner/Makefile
> > +++ b/arch/arm64/boot/dts/allwinner/Makefile
> > @@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-taiqicat-a01.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h313-tanix-tx1.dtb
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts
> > new file mode 100644
> > index 000000000000..381479553f5f
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts
> > @@ -0,0 +1,361 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +// Copyright (C) 2026 Jun Yan <jerrysteve1101@gmail.com>
> > +
> > +/dts-v1/;
> > +
> > +#include "sun50i-h6.dtsi"
> > +#include "sun50i-h6-cpu-opp.dtsi"
> > +#include "sun50i-h6-gpu-opp.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +
> > +/ {
> > +	model = "TaiqiCat (TQC) A01";
> > +	compatible = "ultrapower,taiqicat-a01", "allwinner,sun50i-h6";
> > +
> > +	aliases {
> > +		serial0 = &uart0;
> > +		serial1 = &uart1;
> 
> I don't think we need the serial1 alias? Bluetooth should work even
> without knowing the ttyS<x> device name, shouldn't it?
> 
> But you should add an alias for the WiFi (ethernet0 = &brcm;), so that
> U-Boot assigns an ideally unique MAC address.
> 
> The rest looks correct, from a pure upstream DT perspective, and by
> comparing it to other H6 .dts files, even though I cannot test it, of
> course. But I trust you that those things you mentioned work.

Thank you for the review. 

I will implement the changes you suggested in PATCH v3:
1. drop the serial1 alias
2. add an ethernet0 alias for WiFi.

Best regards,
Jun Yan
> 
> So with the aliases changed:
> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
> 
> Cheers,
> Andre
> 
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +
> > +	connector {
> > +		compatible = "hdmi-connector";
> > +		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
> > +		type = "a";
> > +
> > +		port {
> > +			hdmi_con_in: endpoint {
> > +				remote-endpoint = <&hdmi_out_con>;
> > +			};
> > +		};
> > +	};
> > +
> > +	ext_osc32k: ext-osc32k-clk {
> > +		#clock-cells = <0>;
> > +		compatible = "fixed-clock";
> > +		clock-frequency = <32768>;
> > +		clock-output-names = "ext_osc32k";
> > +	};
> > +
> > +	leds {
> > +		compatible = "gpio-leds";
> > +
> > +		led-0 {
> > +			label = "taiqicat:blue:power";
> > +			gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > +			default-state = "on";
> > +		};
> > +	};
> > +
> > +	reg_vcc5v: vcc5v {
> > +		/* board wide 5V supply directly from the DC jack */
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vcc-5v";
> > +		regulator-min-microvolt = <5000000>;
> > +		regulator-max-microvolt = <5000000>;
> > +		regulator-always-on;
> > +	};
> > +
> > +	sound-spdif {
> > +		compatible = "simple-audio-card";
> > +		simple-audio-card,name = "sun50i-h6-spdif";
> > +
> > +		simple-audio-card,cpu {
> > +			sound-dai = <&spdif>;
> > +		};
> > +
> > +		simple-audio-card,codec {
> > +			sound-dai = <&spdif_out>;
> > +		};
> > +	};
> > +
> > +	spdif_out: spdif-out {
> > +		#sound-dai-cells = <0>;
> > +		compatible = "linux,spdif-dit";
> > +	};
> > +
> > +	wifi_pwrseq: wifi-pwrseq {
> > +		compatible = "mmc-pwrseq-simple";
> > +		clocks = <&rtc CLK_OSC32K_FANOUT>;
> > +		clock-names = "ext_clock";
> > +		reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
> > +		post-power-on-delay-ms = <200>;
> > +	};
> > +};
> > +
> > +&cpu0 {
> > +	cpu-supply = <&reg_dcdca>;
> > +};
> > +
> > +&de {
> > +	status = "okay";
> > +};
> > +
> > +&dwc3 {
> > +	status = "okay";
> > +};
> > +
> > +&ehci0 {
> > +	status = "okay";
> > +};
> > +
> > +&ehci3 {
> > +	status = "okay";
> > +};
> > +
> > +&gpu {
> > +	mali-supply = <&reg_dcdcc>;
> > +	status = "okay";
> > +};
> > +
> > +&hdmi {
> > +	hvcc-supply = <&reg_bldo2>;
> > +	status = "okay";
> > +};
> > +
> > +&hdmi_out {
> > +	hdmi_out_con: endpoint {
> > +		remote-endpoint = <&hdmi_con_in>;
> > +	};
> > +};
> > +
> > +&mmc0 {
> > +	vmmc-supply = <&reg_cldo1>;
> > +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> > +	bus-width = <4>;
> > +	disable-wp;
> > +	status = "okay";
> > +};
> > +
> > +&mmc1 {
> > +	vmmc-supply = <&reg_cldo3>;
> > +	vqmmc-supply = <&reg_bldo3>;
> > +	mmc-pwrseq = <&wifi_pwrseq>;
> > +	bus-width = <4>;
> > +	non-removable;
> > +	keep-power-in-suspend;
> > +	status = "okay";
> > +
> > +	brcm: sdio-wifi@1 {
> > +		reg = <1>;
> > +		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac";
> > +		interrupt-parent = <&r_pio>;
> > +		interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
> > +		interrupt-names = "host-wake";
> > +	};
> > +};
> > +
> > +&mmc2 {
> > +	vmmc-supply = <&reg_cldo1>;
> > +	vqmmc-supply = <&reg_bldo2>;
> > +	cap-mmc-hw-reset;
> > +	non-removable;
> > +	mmc-hs200-1_8v;
> > +	bus-width = <8>;
> > +	status = "okay";
> > +};
> > +
> > +&ohci0 {
> > +	status = "okay";
> > +};
> > +
> > +&ohci3 {
> > +	status = "okay";
> > +};
> > +
> > +&pio {
> > +	vcc-pc-supply = <&reg_bldo2>;
> > +	vcc-pd-supply = <&reg_cldo1>;
> > +	vcc-pg-supply = <&reg_bldo3>;
> > +};
> > +
> > +&r_i2c {
> > +	status = "okay";
> > +
> > +	axp805: pmic@36 {
> > +		compatible = "x-powers,axp805", "x-powers,axp806";
> > +		reg = <0x36>;
> > +		interrupt-parent = <&r_intc>;
> > +		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
> > +		interrupt-controller;
> > +		#interrupt-cells = <1>;
> > +		x-powers,self-working-mode;
> > +		vina-supply = <&reg_vcc5v>;
> > +		vinb-supply = <&reg_vcc5v>;
> > +		vinc-supply = <&reg_vcc5v>;
> > +		vind-supply = <&reg_vcc5v>;
> > +		vine-supply = <&reg_vcc5v>;
> > +		aldoin-supply = <&reg_vcc5v>;
> > +		bldoin-supply = <&reg_vcc5v>;
> > +		cldoin-supply = <&reg_vcc5v>;
> > +
> > +		regulators {
> > +			reg_aldo1: aldo1 {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-name = "vcc-pl-led-ir-pg-pm-ts";
> > +			};
> > +
> > +			reg_aldo2: aldo2 {
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-name = "vcc-ac200";
> > +				regulator-enable-ramp-delay = <100000>;
> > +			};
> > +
> > +			aldo3 {
> > +				/* unused */
> > +			};
> > +
> > +			reg_bldo1: bldo1 {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <1800000>;
> > +				regulator-max-microvolt = <1800000>;
> > +				regulator-name = "vcc18-dram-bias-pll";
> > +			};
> > +
> > +			reg_bldo2: bldo2 {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <1800000>;
> > +				regulator-max-microvolt = <1800000>;
> > +				regulator-name = "vcc-pc-emmc-efuse-hdmi";
> > +			};
> > +
> > +			reg_bldo3: bldo3 {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <1800000>;
> > +				regulator-max-microvolt = <1800000>;
> > +				regulator-name = "vcc-pg-wifiio";
> > +			};
> > +
> > +			bldo4 {
> > +				/* unused */
> > +			};
> > +
> > +			reg_cldo1: cldo1 {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-name = "vcc33-io-pd-emmc-sd-usb-uart";
> > +			};
> > +
> > +			/* This regulator is connected with CLDO3 */
> > +			reg_cldo2: cldo2 {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-name = "vcc-wifi-1";
> > +			};
> > +
> > +			reg_cldo3: cldo3 {
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-name = "vcc-wifi-2";
> > +			};
> > +
> > +			reg_dcdca: dcdca {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <810000>;
> > +				regulator-max-microvolt = <1160000>;
> > +				regulator-ramp-delay = <2500>;
> > +				regulator-name = "vdd-cpu";
> > +			};
> > +
> > +			reg_dcdcc: dcdcc {
> > +				regulator-enable-ramp-delay = <32000>;
> > +				regulator-min-microvolt = <810000>;
> > +				regulator-max-microvolt = <1080000>;
> > +				regulator-ramp-delay = <2500>;
> > +				regulator-name = "vdd-gpu";
> > +			};
> > +
> > +			reg_dcdcd: dcdcd {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <960000>;
> > +				regulator-max-microvolt = <960000>;
> > +				regulator-name = "vdd-sys-hdmi-usb";
> > +			};
> > +
> > +			reg_dcdce: dcdce {
> > +				regulator-always-on;
> > +				regulator-min-microvolt = <1200000>;
> > +				regulator-max-microvolt = <1200000>;
> > +				regulator-name = "vcc-dram";
> > +			};
> > +
> > +			sw {
> > +				/* unused */
> > +			};
> > +		};
> > +	};
> > +};
> > +
> > +&r_ir {
> > +	status = "okay";
> > +};
> > +
> > +&r_pio {
> > +	/*
> > +	 * PL0 and PL1 are used for PMIC I2C
> > +	 * don't enable the pl-supply else
> > +	 * it will fail at boot
> > +	 *
> > +	 * vcc-pl-supply = <&reg_aldo1>;
> > +	 */
> > +	vcc-pm-supply = <&reg_aldo1>;
> > +};
> > +
> > +&rtc {
> > +	clocks = <&ext_osc32k>;
> > +};
> > +
> > +&spdif {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&spdif_tx_pin>;
> > +	status = "okay";
> > +};
> > +
> > +&uart0 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart0_ph_pins>;
> > +	status = "okay";
> > +};
> > +
> > +&uart1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > +	uart-has-rtscts;
> > +	status = "okay";
> > +
> > +	bluetooth {
> > +		compatible = "brcm,bcm43430a1-bt";
> > +		clocks = <&rtc CLK_OSC32K_FANOUT>;
> > +		clock-names = "lpo";
> > +		vbat-supply = <&reg_cldo3>;
> > +		vddio-supply = <&reg_bldo3>;
> > +		device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
> > +		host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
> > +		shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
> > +		max-speed = <1500000>;
> > +	};
> > +};
> > +
> > +&usb2otg {
> > +	dr_mode = "host";
> > +	status = "okay";
> > +};
> > +
> > +&usb2phy {
> > +	usb0_vbus-supply = <&reg_vcc5v>;
> > +	usb3_vbus-supply = <&reg_vcc5v>;
> > +	status = "okay";
> > +};
> > +
> > +&usb3phy {
> > +	status = "okay";
> > +};