[PATCH v2 3/3] ARM: dts: qcom: msm8960: expressatt: Add camera flash

[Rudraksha Gupta via B4 Relay <devnull+guptarud.gmail.com@kernel.org>]

From: Rudraksha Gupta <guptarud@gmail.com>

Add camera flash support for the Samsung Galaxy Express (expressatt).

The flash IC uses a one-wire pulse-count protocol on GPIO 3, powered
by a GPIO-controlled fixed regulator on PMIC MPP 4. The regulator is
modeled as a regulator-fixed node and supplied to the flash IC via
vin-supply.

Downstream references:
Link: https://github.com/LineageOS/android_kernel_samsung_d2/blob/stable/cm-12.0-YNG4N/drivers/leds/Makefile#L51
Link: https://github.com/LineageOS/android_kernel_samsung_d2/blob/stable/cm-12.0-YNG4N/arch/arm/mach-msm/board-apexq-camera.c#L591

Reviewed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
---
 .../dts/qcom/qcom-msm8960-samsung-expressatt.dts   | 43 ++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
index c4b98af6955d..ad5169a60937 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/reset/qcom,gcc-msm8960.h>
 
 #include "qcom-msm8960.dtsi"
@@ -61,6 +62,32 @@ touchkey_enable: touchkey-enable {
 		regulator-boot-on;
 	};
 
+	flash_gpio_reg: regulator-flash {
+		compatible = "regulator-fixed";
+		regulator-name = "flash_led_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pm8921_mpps 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-0 = <&flash_led_unlock>;
+		pinctrl-names = "default";
+	};
+
+	camera_flash: led-controller {
+		compatible = "richtek,rt8515";
+		enf-gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&flash_gpio_reg>;
+		richtek,rfs-ohms = <16000>;
+		pinctrl-0 = <&cam_flash_en>;
+		pinctrl-names = "default";
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+		};
+	};
+
 	i2c-gpio-touchkey {
 		compatible = "i2c-gpio";
 		#address-cells = <1>;
@@ -247,6 +274,13 @@ touchkey_irq_pin: touchkey-irq-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	cam_flash_en: cam-flash-en-state {
+		pins = "gpio3";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-down;
+	};
 };
 
 &pm8921 {
@@ -572,3 +606,12 @@ magnetometer@2e {
 		/* TODO: Figure out Mount Matrix */
 	};
 };
+
+&pm8921_mpps {
+	flash_led_unlock: flash-led-unlock-state {
+		pins = "mpp4";
+		function = "digital";
+		output-low;
+		power-source = <PM8921_GPIO_S4>;
+	};
+};

-- 
2.53.0