[PATCH 0/4] timers: Add support for RZ/N1 SoCs timers

[PATCH 0/4] timers: Add support for RZ/N1 SoCs timers

[Herve Codina (Schneider Electric)]

The Renesas RZ/N1 SoCs family has two timers block controller
available.

Each controller is charge of 8 timers (six 16-bit timers + two 32-bit
timers).

Each timer has its own interrupt, its own prescaler that can be used to
device the clock by 25 (timers block are fed with a 25 MHz clock) and
all timers can work in either one-shot or periodic mode.

This series adds support for those timers blocks.

Best regards,
Hervé

Herve Codina (Schneider Electric) (4):
  dt-bindings: timer: Add the Renesas RZ/N1 timer
  clocksource/drivers: Add support for the Renesas RZ/N1 timers
  ARM: dts: r9a06g032: Add support for timers
  MAINTAINERS: Add the Renesas RZ/N1 timers driver entry

 .../bindings/timer/renesas,rzn1-timer.yaml    |  75 +++
 MAINTAINERS                                   |   7 +
 arch/arm/boot/dts/renesas/r9a06g032.dtsi      |  34 ++
 drivers/clocksource/Kconfig                   |  10 +
 drivers/clocksource/Makefile                  |   1 +
 drivers/clocksource/timer-rzn1.c              | 442 ++++++++++++++++++
 6 files changed, 569 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,rzn1-timer.yaml
 create mode 100644 drivers/clocksource/timer-rzn1.c

-- 
2.53.0

[PATCH 1/4] dt-bindings: timer: Add the Renesas RZ/N1 timer

[Herve Codina (Schneider Electric)]

The Renesas RZ/N1 timer block controller is the controller in charge of
timers available in the Renesas RZ/N1 SoCs family.

This controller handles 8 timers:
 - 6 16-bit timers
 - 2 32-bit timers

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
---
 .../bindings/timer/renesas,rzn1-timer.yaml    | 75 +++++++++++++++++++
 1 file changed, 75 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/timer/renesas,rzn1-timer.yaml

diff --git a/Documentation/devicetree/bindings/timer/renesas,rzn1-timer.yaml b/Documentation/devicetree/bindings/timer/renesas,rzn1-timer.yaml
new file mode 100644
index 000000000000..b9a725837d7c
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/renesas,rzn1-timer.yaml
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/timer/renesas,rzn1-timer.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas RZ/N1 timers
+
+maintainers:
+  - Herve Codina <herve.codina@bootlin.com>
+
+description: |
+  The Renesas RZ/N1 SoCs timers block controller is composed of 8 independent
+  timers.
+    - 6 are 16-bit timers
+    - 2 are 32-bit timers
+
+  Each timer has its own interrupt line and can work in either one-shot or
+  periodic mode.
+
+properties:
+  compatible:
+    items:
+      - const: renesas,r9a06g032-timer   # RZ/N1D
+      - const: renesas,rzn1-timer
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: APB internal bus clock
+
+  clock-names:
+    items:
+      - const: pclk
+
+  power-domains:
+    maxItems: 1
+
+  interrupts:
+    minItems: 8
+    maxItems: 8
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - power-domains
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/r9a06g032-sysctrl.h>
+
+    timer@51001000 {
+        compatible = "renesas,r9a06g032-timer", "renesas,rzn1-timer";
+        reg = <0x51001000 0x400>;
+        clocks = <&sysctrl R9A06G032_HCLK_TIMER0>;
+        clock-names = "pclk";
+        power-domains = <&sysctrl>;
+        interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+    };
+...
-- 
2.53.0

[PATCH 2/4] clocksource/drivers: Add support for the Renesas RZ/N1 timers

[Herve Codina (Schneider Electric)]

The Renesas RZ/N1 timer block controller is the controller in charge of
timers available in the Renesas RZ/N1 SoCs family.

This controller handles 8 timers:
  - 6 16-bit timers
  - 2 32-bit timers

Each timer has its own interrupt, its own prescaler that can be used to
device the clock by 25 and all of them can work in either one-shot or
periodic mode.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
---
 drivers/clocksource/Kconfig      |  10 +
 drivers/clocksource/Makefile     |   1 +
 drivers/clocksource/timer-rzn1.c | 442 +++++++++++++++++++++++++++++++
 3 files changed, 453 insertions(+)
 create mode 100644 drivers/clocksource/timer-rzn1.c

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index fd9112706545..31cf40880ece 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -152,6 +152,16 @@ config REALTEK_OTTO_TIMER
 	  RT8391, RTL8392, RTL8393 and RTL8396 and chips of the RTL930x series
 	  such as RTL9301, RTL9302 or RTL9303.
 
+config RZN1_TIMER
+	bool "Renesas RZ/N1 Timer"
+	depends on HAS_IOMEM && COMMON_CLK && (ARCH_RZN1 || COMPILE_TEST)
+	help
+	  Enables support for RZ/N1 SoC timers.
+	  A timers block in RZ/N1 SoCs is composed of 8 timers
+	    - 6 16-bit timers
+	    - 2 32-bit timers
+	  Two timers blocks are available in RZ/N1 SoCs.
+
 config SUN4I_TIMER
 	bool "Sun4i timer driver" if COMPILE_TEST
 	depends on HAS_IOMEM
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index b46376af6b49..464ec6690ab6 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -96,3 +96,4 @@ obj-$(CONFIG_EP93XX_TIMER)		+= timer-ep93xx.o
 obj-$(CONFIG_RALINK_TIMER)		+= timer-ralink.o
 obj-$(CONFIG_NXP_STM_TIMER)		+= timer-nxp-stm.o
 obj-$(CONFIG_RTK_SYSTIMER)		+= timer-realtek.o
+obj-$(CONFIG_RZN1_TIMER)		+= timer-rzn1.o
diff --git a/drivers/clocksource/timer-rzn1.c b/drivers/clocksource/timer-rzn1.c
new file mode 100644
index 000000000000..1b95b0b5cd3b
--- /dev/null
+++ b/drivers/clocksource/timer-rzn1.c
@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * RZ/N1 timers driver
+ *
+ * Copyright (C) 2026 Schneider-Electric
+ *
+ * Author: Herve Codina <herve.codina@bootlin.com>
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/cpuhotplug.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/sched_clock.h>
+
+/* Per-timer register offsets */
+#define RZN1_TIMER_LOAD_COUNT_REG	0x00
+#define RZN1_TIMER_CURRENT_COUNT_REG	0x04
+#define RZN1_TIMER_CONTROL_REG		0x08
+#define   RZN1_TIMER_CONTROL_INT_UNMASK		BIT(3)
+#define   RZN1_TIMER_CONTROL_ENABLE		BIT(2)
+#define   RZN1_TIMER_CONTROL_AUTORELOAD		BIT(1)
+#define   RZN1_TIMER_CONTROL_PRESCALER_DIV25	BIT(0)
+#define RZN1_TIMER_CLEAR_INT_REG	0x0c
+#define RZN1_TIMER_STATUS_INT0_REG	0x10
+#define RZN1_TIMER_STATUS_INT1_REG	0x14
+
+/*
+ * 8 timers are available. Among those 8 timers, the first 6 timers are 16-bit
+ * timers and the last two ones are 32-bit timers.
+ */
+#define RZN1_TIMER_BASE_INDEX_16BIT_TIMERS 0
+#define RZN1_TIMER_NB_16BIT_TIMERS 6
+
+#define RZN1_TIMER_BASE_INDEX_32BIT_TIMER 6
+#define RZN1_TIMER_NB_32BIT_TIMERS 2
+
+#define RZN1_TIMER_IS_16BIT_TIMER(_i) ((_i) < RZN1_TIMER_BASE_INDEX_32BIT_TIMER)
+
+/* Total numbers of timers */
+#define RZN1_TIMER_NB_TIMERS	(RZN1_TIMER_NB_16BIT_TIMERS + \
+				 RZN1_TIMER_NB_32BIT_TIMERS)
+
+/* Offset of registers related to the timer number _i in the timers regs area */
+#define RZN1_TIMER_REGS_OFFSET(_i) (0x20 * (_i))
+
+struct rzn1_timer {
+	void __iomem *base;
+	unsigned int width;
+	unsigned long rate;
+	unsigned long hz_period;
+	struct clock_event_device ced;
+};
+
+static int rzn1_timer_config(struct rzn1_timer *timer, u32 period, bool is_periodic)
+{
+	u32 ctrl;
+
+	ctrl = readl(timer->base + RZN1_TIMER_CONTROL_REG);
+
+	/* Disable the timer */
+	writel(ctrl & ~RZN1_TIMER_CONTROL_ENABLE,
+	       timer->base + RZN1_TIMER_CONTROL_REG);
+
+	/* Set the new period */
+	writel(period, timer->base + RZN1_TIMER_LOAD_COUNT_REG);
+
+	/* Prepare the timer mode */
+	if (is_periodic)
+		ctrl |= RZN1_TIMER_CONTROL_AUTORELOAD;
+	else
+		ctrl &= ~RZN1_TIMER_CONTROL_AUTORELOAD;
+
+	/*
+	 * Enable the timer.
+	 *
+	 * This automatically resets the CURRENT_COUNT register.
+	 */
+	ctrl |= RZN1_TIMER_CONTROL_ENABLE;
+	writel(ctrl, timer->base + RZN1_TIMER_CONTROL_REG);
+
+	return 0;
+}
+
+static void rzn1_timer_disable(struct rzn1_timer *timer)
+{
+	u32 ctrl;
+
+	ctrl = readl(timer->base + RZN1_TIMER_CONTROL_REG);
+	ctrl &= ~RZN1_TIMER_CONTROL_ENABLE;
+	writel(ctrl, timer->base + RZN1_TIMER_CONTROL_REG);
+}
+
+static void rzn1_timer_int_enable(struct rzn1_timer *timer)
+{
+	u32 ctrl;
+
+	ctrl = readl(timer->base + RZN1_TIMER_CONTROL_REG);
+	ctrl |= RZN1_TIMER_CONTROL_INT_UNMASK;
+	writel(ctrl, timer->base + RZN1_TIMER_CONTROL_REG);
+}
+
+static irqreturn_t rzn1_timer_interrupt(int irq, void *dev_id)
+{
+	struct rzn1_timer *timer = dev_id;
+
+	/* Ack the interrupt */
+	readl(timer->base + RZN1_TIMER_CLEAR_INT_REG);
+
+	timer->ced.event_handler(&timer->ced);
+	return IRQ_HANDLED;
+}
+
+static int rzn1_clkevt_set_next_event(unsigned long cycles,
+				      struct clock_event_device *evt)
+{
+	struct rzn1_timer *timer = container_of(evt, struct rzn1_timer, ced);
+
+	return rzn1_timer_config(timer, cycles, false);
+}
+
+static int rzn1_clkevt_shutdown(struct clock_event_device *evt)
+{
+	struct rzn1_timer *timer = container_of(evt, struct rzn1_timer, ced);
+
+	rzn1_timer_disable(timer);
+	return 0;
+}
+
+static int rzn1_clkevt_set_periodic(struct clock_event_device *evt)
+{
+	struct rzn1_timer *timer = container_of(evt, struct rzn1_timer, ced);
+
+	rzn1_timer_config(timer, timer->hz_period, true);
+	return 0;
+}
+
+/*
+ * This global lock is used to prevent race conditions during global timers
+ * test and set operation in case the driver is using the async probe option.
+ */
+static DEFINE_MUTEX(rzn1_global_timers_lock);
+
+static int rzn1_timer_instance;
+
+/* scheduler and clocksource */
+static struct rzn1_timer *rzn1_sched_clock;
+
+static u64 notrace rzn1_sched_read(void)
+{
+	return readl_relaxed(rzn1_sched_clock->base + RZN1_TIMER_CURRENT_COUNT_REG);
+}
+
+static u64 rzn1_clksrc_read(struct clocksource *cs)
+{
+	return readl_relaxed(rzn1_sched_clock->base + RZN1_TIMER_CURRENT_COUNT_REG);
+}
+
+static struct clocksource rzn1_clocksource = {
+	.name = "rzn1_timer_clocksource",
+	.rating = 200,
+	.flags = CLOCK_SOURCE_IS_CONTINUOUS | CLOCK_SOURCE_SUSPEND_NONSTOP,
+	.read = rzn1_clksrc_read,
+};
+
+/* Timers table where 32-bit timers will be assigned per-cpu */
+static struct rzn1_timer *rzn1_tab_timers;
+
+static int rzn1_local_timer_starting_cpu(unsigned int cpu)
+{
+	struct rzn1_timer *timer;
+
+	if (cpu > RZN1_TIMER_NB_32BIT_TIMERS)
+		return -EINVAL;
+
+	timer = &rzn1_tab_timers[cpu + RZN1_TIMER_BASE_INDEX_32BIT_TIMER];
+
+	timer->ced.cpumask = cpumask_of(cpu);
+	irq_force_affinity(timer->ced.irq, cpumask_of(cpu));
+	clockevents_config_and_register(&timer->ced, timer->rate, 1,
+					GENMASK(timer->width - 1, 0));
+
+	return 0;
+}
+
+static void rzn1_timer_init(struct rzn1_timer *timer, unsigned int index,
+			    void __iomem *timers_base, unsigned long clock_rate)
+{
+	timer->base = timers_base + RZN1_TIMER_REGS_OFFSET(index);
+
+	/* Disable the timer */
+	writel(0, timer->base + RZN1_TIMER_CONTROL_REG);
+
+	/* Clear potential interrupts */
+	readl(timer->base + RZN1_TIMER_CLEAR_INT_REG);
+
+	if (RZN1_TIMER_IS_16BIT_TIMER(index)) {
+		timer->width = 16;
+		/*
+		 * Enable pre-scaler for 16-bit timers.
+		 *
+		 * Timers are fed by a 25MHz clock. With this pre-scaler (1/25)
+		 * enabled, the 16-bit timers resolution is 1 microsecond.
+		 */
+		writel(RZN1_TIMER_CONTROL_PRESCALER_DIV25,
+		       timer->base + RZN1_TIMER_CONTROL_REG);
+		timer->rate = clock_rate / 25;
+	} else {
+		timer->width = 32;
+		timer->rate = clock_rate;
+	}
+	timer->hz_period = DIV_ROUND_UP(timer->rate, HZ);
+}
+
+static void rzn1_timer_clkevt_init_ced(struct rzn1_timer *timer, const char *name,
+				       int irq)
+{
+	timer->ced.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
+	timer->ced.set_next_event = rzn1_clkevt_set_next_event;
+	timer->ced.set_state_shutdown = rzn1_clkevt_shutdown;
+	timer->ced.set_state_periodic = rzn1_clkevt_set_periodic;
+	timer->ced.cpumask = cpu_possible_mask;
+
+	/*
+	 * 32-bit timers are fed with a 25 MHz clock directly derived from the
+	 * main PLL (1 GHz). The arch timer, ARMv7 CP15 in RZ/N1 SoCs, is fed
+	 * with to a 6.25 MHz clock.
+	 *
+	 * The clock of the RZ/N1 timers block is a stable one and the RZ/N1
+	 * timers have a higher resolution than the ARM CP15 one.
+	 *
+	 * Also those 32-bit RZ/N1 timers are assigned per-cpu.
+	 *
+	 * Use a high rating for the 32-bit RZ/N1 timers in order to have them
+	 * chosen by the system.
+	 */
+	timer->ced.rating = timer->width == 16 ? 200 : 460;
+	timer->ced.owner = THIS_MODULE;
+	timer->ced.name = name;
+	timer->ced.irq = irq;
+}
+
+static int rzn1_timer_probe_first(struct platform_device *pdev, struct rzn1_timer *tab_timers,
+				  void __iomem *base, unsigned long clock_rate)
+{
+	struct device *dev = &pdev->dev;
+	struct rzn1_timer *timer;
+	unsigned int i;
+	char *name;
+	int irq;
+	int ret;
+
+	/*
+	 * Probe the first instance. In that case, timers are assigned as
+	 * follow:
+	 *   - First 16-bit timer: clocksource and sched_clock
+	 *   - Other 16-bit timers: clock events for all possible CPUs
+	 *   - 32-bit timers: clock events per CPU
+	 *
+	 * First step, perform all operation that could fail without calling
+	 * clockevents_config_and_register(), sched_clock_register() nor
+	 * cpuhp_setup_state(). Those operation don't have unregister nor
+	 * teardown counterparts and so, once called, we cannot remove the
+	 * related resource.
+	 */
+
+	/*
+	 * First step for 16-bit timers except the first one and all 32-bit
+	 * timers.
+	 */
+	for (i = RZN1_TIMER_BASE_INDEX_16BIT_TIMERS + 1; i < RZN1_TIMER_NB_TIMERS; i++) {
+		timer = &tab_timers[i];
+
+		rzn1_timer_init(timer, i, base, clock_rate);
+
+		irq = platform_get_irq(pdev, i);
+		if (irq < 0)
+			return irq;
+
+		name = devm_kasprintf(dev, GFP_KERNEL, "%s-%u", dev_name(dev), i);
+		if (!name)
+			return -ENOMEM;
+
+		rzn1_timer_clkevt_init_ced(timer, name, irq);
+
+		ret = devm_request_irq(dev, timer->ced.irq, rzn1_timer_interrupt,
+				       IRQF_TIMER, timer->ced.name, timer);
+		if (ret < 0)
+			return dev_err_probe(dev, irq, "timer%d: Failed to request IRQ\n", i);
+
+		rzn1_timer_int_enable(timer);
+	}
+
+	/*
+	 * Second step, almost all operations that can fail have been called.
+	 * Timers are ready to work. Start with the last operation that can fail,
+	 * installing and invoking hotplug callbacks
+	 */
+	rzn1_tab_timers = tab_timers;
+	ret = cpuhp_setup_state(CPUHP_AP_ONLINE_DYN,
+				"clockevents/rzn1/global_timer:starting",
+				rzn1_local_timer_starting_cpu, NULL);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Setup CPU hotplug state failed\n");
+
+	/*
+	 * At this point, no more operations can fail. Perform remaining
+	 * operations. Starting by handling the first 16-bit timer
+	 */
+	timer = &tab_timers[RZN1_TIMER_BASE_INDEX_16BIT_TIMERS];
+
+	rzn1_timer_init(timer, RZN1_TIMER_BASE_INDEX_16BIT_TIMERS, base, clock_rate);
+	rzn1_timer_config(timer, GENMASK(timer->width - 1, 0), true);
+
+	rzn1_sched_clock = timer;
+
+	sched_clock_register(rzn1_sched_read, rzn1_sched_clock->width, rzn1_sched_clock->rate);
+
+	rzn1_clocksource.mask = CLOCKSOURCE_MASK(rzn1_sched_clock->width);
+	clocksource_register_hz(&rzn1_clocksource, rzn1_sched_clock->rate);
+
+	/*
+	 * Register clockevents only for 16-bit timers. 32-bit timers clockevents
+	 * are registered by CPU hotplug startup function set previously by the
+	 * cpuhp_setup_state() call.
+	 */
+	for (i = RZN1_TIMER_BASE_INDEX_16BIT_TIMERS + 1; i < RZN1_TIMER_NB_16BIT_TIMERS; i++) {
+		timer = &tab_timers[i];
+		clockevents_config_and_register(&timer->ced, timer->rate,
+						1, GENMASK(timer->width - 1, 0));
+	}
+
+	return 0;
+}
+
+static int rzn1_timer_probe_other(struct platform_device *pdev, struct rzn1_timer *tab_timers,
+				  void __iomem *base, unsigned long clock_rate)
+{
+	struct device *dev = &pdev->dev;
+	struct rzn1_timer *timer;
+	unsigned int i;
+	char *name;
+	int irq;
+	int ret;
+
+	/*
+	 * Probe other instance(s), i.e. not the first one. In that case,
+	 * all timers are used as clock events and available for all possible
+	 * CPUs
+	 *
+	 * First step, perform all operation that could fail without calling
+	 * clockevents_config_and_register(). Unregister counterpart does not
+	 * exist and so, once called, we cannot remove the related resource.
+	 */
+	for (i = 0; i < RZN1_TIMER_NB_TIMERS; i++) {
+		timer = &tab_timers[i];
+
+		rzn1_timer_init(timer, i, base, clock_rate);
+
+		irq = platform_get_irq(pdev, i);
+		if (irq < 0)
+			return irq;
+
+		name = devm_kasprintf(dev, GFP_KERNEL, "%s-%u", dev_name(dev), i);
+		if (!name)
+			return -ENOMEM;
+
+		rzn1_timer_clkevt_init_ced(timer, name, irq);
+
+		ret = devm_request_irq(dev, timer->ced.irq, rzn1_timer_interrupt,
+				       IRQF_TIMER, timer->ced.name, timer);
+		if (ret < 0)
+			return dev_err_probe(dev, irq, "timer%d: Failed to request IRQ\n", i);
+
+		rzn1_timer_int_enable(timer);
+	}
+
+	/*
+	 * Second step, all operation that can fail have been called. We can
+	 * register our timers
+	 */
+
+	for (i = 0; i < RZN1_TIMER_NB_TIMERS; i++) {
+		timer = &tab_timers[i];
+		clockevents_config_and_register(&timer->ced, timer->rate,
+						1, GENMASK(timer->width - 1, 0));
+	}
+
+	return 0;
+}
+
+static int rzn1_timer_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rzn1_timer *tab_timers;
+	unsigned long clock_rate;
+	void __iomem *base;
+	struct clk *clk;
+	int ret;
+
+	tab_timers = devm_kcalloc(dev, RZN1_TIMER_NB_TIMERS, sizeof(*tab_timers),
+				  GFP_KERNEL);
+	if (!tab_timers)
+		return -ENOMEM;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	clk = devm_clk_get_enabled(dev, "pclk");
+	if (IS_ERR(clk))
+		return dev_err_probe(dev, PTR_ERR(clk), "Failed to get pclk\n");
+
+	clock_rate = clk_get_rate(clk);
+
+	scoped_guard(mutex, &rzn1_global_timers_lock) {
+		ret = !rzn1_timer_instance ?
+			rzn1_timer_probe_first(pdev, tab_timers, base, clock_rate) :
+			rzn1_timer_probe_other(pdev, tab_timers, base, clock_rate);
+		if (!ret)
+			rzn1_timer_instance++;
+	}
+
+	return ret;
+}
+
+static const struct of_device_id rzn1_timer_of_match[] = {
+	{ .compatible = "renesas,rzn1-timer", },
+	{ /* sentinel */ }
+};
+
+static struct platform_driver rzn1_timer_driver = {
+	.driver = {
+		.name = "rzn1_timer",
+		.of_match_table = rzn1_timer_of_match,
+	},
+};
+builtin_platform_driver_probe(rzn1_timer_driver, rzn1_timer_probe);
-- 
2.53.0

[PATCH 3/4] ARM: dts: r9a06g032: Add support for timers

[Herve Codina (Schneider Electric)]

In the Renesas RZ/N1 SoCs family, two timers block are available.

Each block contains 8 timers composed of 6 16-bits timers and 2 32-bits
timers.

Each timer has its own interrupt line.

Describe those timers blocks.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 34 ++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index f4f760aff28b..7d736e1e835a 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -674,6 +674,40 @@ gpioirqmux: interrupt-controller@51000480 {
 			status = "disabled";
 		};
 
+		timer0: timer@51001000 {
+			compatible = "renesas,r9a06g032-timer", "renesas,rzn1-timer";
+			reg = <0x51001000 0x400>;
+			clocks = <&sysctrl R9A06G032_HCLK_TIMER0>;
+			clock-names = "pclk";
+			power-domains = <&sysctrl>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		timer1: timer@51002000 {
+			compatible = "renesas,r9a06g032-timer", "renesas,rzn1-timer";
+			reg = <0x51002000 0x400>;
+			clocks = <&sysctrl R9A06G032_HCLK_TIMER1>;
+			clock-names = "pclk";
+			power-domains = <&sysctrl>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		can0: can@52104000 {
 			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
 			reg = <0x52104000 0x800>;
-- 
2.53.0

[PATCH 4/4] MAINTAINERS: Add the Renesas RZ/N1 timers driver entry

[Herve Codina (Schneider Electric)]

After contributing the driver, add myself as the maintainer for the
Renesas RZ/N1 timers driver.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 55af015174a5..5655d8b0c89e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22512,6 +22512,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/rtc/renesas,rzn1-rtc.yaml
 F:	drivers/rtc/rtc-rzn1.c
 
+RENESAS RZ/N1 TIMERS DRIVER
+M:	Herve Codina <herve.codina@bootlin.com>
+L:	linux-renesas-soc@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/timer/renesas,rzn1-timer.yaml
+F:	drivers/clocksource/timer-rzn1.c
+
 RENESAS RZ/N1 USBF CONTROLLER DRIVER
 M:	Herve Codina <herve.codina@bootlin.com>
 L:	linux-renesas-soc@vger.kernel.org
-- 
2.53.0

Re: [PATCH 1/4] dt-bindings: timer: Add the Renesas RZ/N1 timer

[Krzysztof Kozlowski]

On Tue, Mar 31, 2026 at 05:26:12PM +0200, Herve Codina (Schneider Electric) wrote:
> +properties:
> +  compatible:
> +    items:
> +      - const: renesas,r9a06g032-timer   # RZ/N1D
> +      - const: renesas,rzn1-timer
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: APB internal bus clock
> +
> +  clock-names:
> +    items:
> +      - const: pclk
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  interrupts:
> +    minItems: 8

Drop minItems

With this:

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof