From: Elson Serrao <elson.serrao@oss.qualcomm.com>
To: Bjorn Andersson <andersson@kernel.org>,
Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Rob Herring <robh@kernel.org>, Conor Dooley <conor+dt@kernel.org>,
Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v4 9/9] arm64: dts: qcom: Map USB connector to EUD on Kodiak boards
Date: Fri, 1 May 2026 10:06:35 -0700 [thread overview]
Message-ID: <20260501170635.2641748-10-elson.serrao@oss.qualcomm.com> (raw)
In-Reply-To: <20260501170635.2641748-1-elson.serrao@oss.qualcomm.com>
On Kodiak-based boards, the primary USB connector is connected through
the EUD on the High-Speed path. Update the board-level descriptions to
map the USB connector endpoint to EUD, reflecting the intended hardware
topology.
Signed-off-by: Elson Serrao <elson.serrao@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts | 10 +++++-----
arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts | 10 +++++-----
arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 10 +++++-----
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 10 +++++-----
.../boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts | 10 +++++-----
arch/arm64/boot/dts/qcom/sm7325-nothing-spacewar.dts | 10 +++++-----
6 files changed, 30 insertions(+), 30 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts b/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
index 04cb9230d29f..c213e06a4428 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
@@ -98,7 +98,7 @@ port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
+ remote-endpoint = <&eud_con>;
};
};
@@ -1478,10 +1478,6 @@ &usb_1 {
status = "okay";
};
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
&usb_1_hsphy {
vdda-pll-supply = <&vreg_l10c>;
vdda18-supply = <&vreg_l1c>;
@@ -1521,3 +1517,7 @@ &wifi {
qcom,calibration-variant = "Fairphone_5";
status = "okay";
};
+
+&eud_con {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
diff --git a/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts b/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
index bf18c4852081..e9c0463daa53 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
@@ -74,7 +74,7 @@ port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
+ remote-endpoint = <&eud_con>;
};
};
@@ -826,10 +826,6 @@ &usb_1 {
status = "okay";
};
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
&usb_1_hsphy {
vdda-pll-supply = <&vreg_l10c_0p88>;
vdda33-supply = <&vreg_l2b_3p072>;
@@ -862,3 +858,7 @@ &usb_2_hsphy {
&usb_dp_qmpphy_out {
remote-endpoint = <&pmic_glink_ss_in>;
};
+
+&eud_con {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
index 797f37596bf1..650c4fbc1606 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
@@ -84,7 +84,7 @@ port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
+ remote-endpoint = <&eud_con>;
};
};
@@ -952,10 +952,6 @@ &usb_1 {
status = "okay";
};
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
&usb_1_hsphy {
vdda-pll-supply = <&vreg_l10c>;
vdda18-supply = <&vreg_l1c>;
@@ -986,6 +982,10 @@ &usb_dp_qmpphy_out {
remote-endpoint = <&pmic_glink_ss_in>;
};
+&eud_con {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
&venus {
firmware-name = "qcom/qcm6490/SHIFT/otter/venus.mbn";
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index e393ccf1884a..a0db2a2745d2 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -194,7 +194,7 @@ port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
+ remote-endpoint = <&eud_con>;
};
};
@@ -1371,14 +1371,14 @@ &usb_1 {
status = "okay";
};
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
&usb_1_dwc3_ss {
remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
};
+&eud_con {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
&usb_1_hsphy {
vdda-pll-supply = <&vreg_l10c_0p88>;
vdda33-supply = <&vreg_l2b_3p072>;
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
index f47efca42d48..387c38aa87d2 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
@@ -93,7 +93,7 @@ port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
+ remote-endpoint = <&eud_con>;
};
};
@@ -1090,10 +1090,6 @@ &usb_1 {
status = "okay";
};
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
&usb_1_hsphy {
vdda-pll-supply = <&vreg_l10c_0p88>;
vdda33-supply = <&vreg_l2b_3p072>;
@@ -1127,6 +1123,10 @@ &usb_dp_qmpphy_out {
remote-endpoint = <&pmic_glink_ss_in>;
};
+&eud_con {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
&ufs_mem_hc {
reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
vcc-supply = <&vreg_l7b_2p952>;
diff --git a/arch/arm64/boot/dts/qcom/sm7325-nothing-spacewar.dts b/arch/arm64/boot/dts/qcom/sm7325-nothing-spacewar.dts
index cb59c122f6f6..a2e160f3f46e 100644
--- a/arch/arm64/boot/dts/qcom/sm7325-nothing-spacewar.dts
+++ b/arch/arm64/boot/dts/qcom/sm7325-nothing-spacewar.dts
@@ -99,7 +99,7 @@ port@0 {
reg = <0>;
pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
+ remote-endpoint = <&eud_con>;
};
};
@@ -1440,10 +1440,6 @@ &usb_1 {
status = "okay";
};
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
&usb_1_hsphy {
vdda-pll-supply = <&vdd_a_usbhs_core>;
vdda18-supply = <&vdd_a_usbhs_1p8>;
@@ -1459,3 +1455,7 @@ &venus {
&wifi {
status = "okay";
};
+
+&eud_con {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
--
2.34.1
prev parent reply other threads:[~2026-05-01 17:06 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-01 17:06 [PATCH v4 0/9] Improve Qualcomm EUD driver and platform support Elson Serrao
2026-05-01 17:06 ` [PATCH v4 1/9] dt-bindings: soc: qcom: eud: Add per-path child nodes for UTMI routing Elson Serrao
2026-05-01 17:06 ` [PATCH v4 2/9] usb: misc: qcom_eud: add sysfs attribute for port selection Elson Serrao
2026-05-01 17:06 ` [PATCH v4 3/9] usb: misc: qcom_eud: add per-path High-Speed PHY control Elson Serrao
2026-05-01 17:06 ` [PATCH v4 4/9] usb: misc: qcom_eud: add per-path role switch support Elson Serrao
2026-05-01 17:06 ` [PATCH v4 5/9] usb: misc: qcom_eud: improve enable_store API Elson Serrao
2026-05-01 17:06 ` [PATCH v4 6/9] usb: misc: qcom_eud: add host mode coordination Elson Serrao
2026-05-01 17:06 ` [PATCH v4 7/9] usb: misc: qcom_eud: fix virtual attach/detach event handling Elson Serrao
2026-05-01 17:06 ` [PATCH v4 8/9] arm64: dts: qcom: kodiak: Describe EUD UTMI path using child node Elson Serrao
2026-05-01 17:06 ` Elson Serrao [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260501170635.2641748-10-elson.serrao@oss.qualcomm.com \
--to=elson.serrao@oss.qualcomm.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@oss.qualcomm.com \
--cc=gregkh@linuxfoundation.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=quic_schowdhu@quicinc.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox