From: Judith Mendez <jm@ti.com>
To: Judith Mendez <jm@ti.com>, Nishanth Menon <nm@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tero Kristo <kristo@kernel.org>, Rob Herring <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Andrew Davis <afd@ti.com>, Bryan Brattlof <bb@ti.com>
Subject: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Date: Fri, 1 May 2026 18:31:48 -0500 [thread overview]
Message-ID: <20260501233148.4180391-3-jm@ti.com> (raw)
In-Reply-To: <20260501233148.4180391-1-jm@ti.com>
BeagleBoard.org BeagleBadge is a compact, affordable open source
hardware single board computer based on the Texas Instruments AM62L3
SoC designed for IoT and embedded applications with low power consumption.
Expansion is provided over open standards based headers including
QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadge
Co-developed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 1 +
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts | 655 +++++++++++++++++++++
2 files changed, 656 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am62l3-badge.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 5269c9619b65..aa714777a3a0 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62d2-evm.dtb
# Boards with AM62Lx SoCs
dtb-$(CONFIG_ARCH_K3) += k3-am62l3-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am62l3-badge.dtb
# Boards with AM62Px SoC
dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am62l3-badge.dts b/arch/arm64/boot/dts/ti/k3-am62l3-badge.dts
new file mode 100644
index 000000000000..0125d3fec5e9
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62l3-badge.dts
@@ -0,0 +1,655 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * https://www.beagleboard.org/boards/beaglebadge
+ *
+ * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-am62l3.dtsi"
+#include "k3-pinctrl.h"
+
+/ {
+ compatible = "beagle,am62l3-badge", "ti,am62l3";
+ model = "BeagleBoard.org BeagleBadge";
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio2;
+ gpio2 = &wkup_gpio0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c4 = &wkup_i2c0;
+ mmc1 = &sdhci1;
+ mmc2 = &sdhci2;
+ serial3 = &uart1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ };
+
+ memory@80000000 {
+ /* 256MB */
+ reg = <0x00000000 0x80000000 0x00000000 0x10000000>;
+ device_type = "memory";
+ bootph-all;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usr_button_default_pins>;
+
+ button-select {
+ label = "SELECT";
+ linux,code = <KEY_SELECT>;
+ gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ };
+
+ button-back {
+ label = "BACK";
+ linux,code = <KEY_BACK>;
+ gpios = <&gpio0 104 GPIO_ACTIVE_LOW>;
+ };
+
+ button-up {
+ label = "UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio0 32 GPIO_ACTIVE_LOW>;
+ };
+
+ button-down {
+ label = "DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio0 42 GPIO_ACTIVE_LOW>;
+ };
+
+ button-left {
+ label = "LEFT";
+ linux,code = <KEY_LEFT>;
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ };
+
+ button-right {
+ label = "RIGHT";
+ linux,code = <KEY_RIGHT>;
+ gpios = <&gpio0 95 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ multicolor-led {
+ compatible = "pwm-leds-multicolor";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgb_led_default_pins>;
+
+ multi-led {
+ color = <LED_COLOR_ID_RGB>;
+ max-brightness = <255>;
+
+ led-red {
+ pwms = <&ecap2 0 255 0>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led-green {
+ pwms = <&ecap1 0 255 0>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led-blue {
+ pwms = <&epwm1 1 255 0>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+ };
+
+ seven-segment-left {
+ compatible = "gpio-7-segment";
+ segment-gpios = <&mcp23s18 0 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 1 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 2 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 3 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 4 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 5 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 6 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 7 GPIO_ACTIVE_LOW>;
+ };
+
+ seven-segment-right {
+ compatible = "gpio-7-segment";
+ segment-gpios = <&mcp23s18 8 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 9 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 10 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 11 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 12 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 13 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 14 GPIO_ACTIVE_LOW>,
+ <&mcp23s18 15 GPIO_ACTIVE_LOW>;
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&epwm0 1 1000000 0>;
+ amp-supply = <&sensor_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_beeper_default_pins>;
+ };
+
+ vsys_out: regulator-0 {
+ /* output of BQ24070 */
+ compatible = "regulator-fixed";
+ regulator-name = "VSYS_OUT";
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ bootph-all;
+ };
+
+ vcc_3v3_main: regulator-1 {
+ /* output of TPS62A06 */
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3_MAIN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vsys_out>;
+ regulator-always-on;
+ regulator-boot-on;
+ bootph-all;
+ };
+
+ vdd_3v3: regulator-2 {
+ /* output of TPS22965 */
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vsys_out>;
+ regulator-always-on;
+ regulator-boot-on;
+ bootph-all;
+ };
+
+ vdd_3v3_sd: regulator-3 {
+ /* TPS22918DBVR */
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3_SD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vdd_3v3>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_3v3_sd_ena_default_pins>;
+ bootph-all;
+ };
+
+ sensor_3v3: regulator-4 {
+ /* TPS22918DBVR */
+ compatible = "regulator-fixed";
+ regulator-name = "Sensor_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vdd_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&wkup_gpio0 1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sensor_3v3_ena_default_pins>;
+ bootph-all;
+ };
+
+ wlan_en: regulator-5 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan_en";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpios = <&gpio0 51 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_en_pins_default>;
+ };
+};
+
+&pmx0 {
+ uart0_default_pins: uart0-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x01b8, PIN_OUTPUT, 0) /* (C13) UART0_TXD */
+ AM62LX_IOPAD(0x01b4, PIN_INPUT, 0) /* (D13) UART0_RXD */
+ >;
+ bootph-all;
+ };
+
+ uart0_wakeup_pins: uart0-wakeup-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x01b8, PIN_OUTPUT, 0) /* (C13) UART0_TXD */
+ AM62LX_IOPAD(0x01b4, PIN_INPUT | PIN_WKUP_EN, 0) /* (D13) UART0_RXD */
+ >;
+ bootph-all;
+ };
+
+ uart1_default_pins: uart1-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x019c, PIN_OUTPUT, 2) /* (A12) UART1_TXD */
+ AM62LX_IOPAD(0x0198, PIN_INPUT, 2) /* (C11) UART1_RXD */
+ AM62LX_IOPAD(0x0180, PIN_INPUT, 2) /* (A8) UART1_CTS */
+ AM62LX_IOPAD(0x0184, PIN_OUTPUT, 2) /* (B10) UART1_RTS */
+ >;
+ bootph-all;
+ };
+
+ usr_button_default_pins: usr-button-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x00a4, PIN_INPUT, 7) /* (H18) GPMC0_AD11.GPIO0_26 */
+ AM62LX_IOPAD(0x01e4, PIN_INPUT, 7) /* (D16) EXT_REFCLK1.GPIO0_104 */
+ AM62LX_IOPAD(0x00c0, PIN_INPUT, 7) /* (N19) GPMC0_ADVn_ALE.GPIO0_32 */
+ AM62LX_IOPAD(0x00e8, PIN_INPUT, 7) /* (L19) GPMC0_CSn1.GPIO0_42 */
+ AM62LX_IOPAD(0x00b8, PIN_INPUT, 7) /* (L21) GPMC0_CLK.GPIO0_31 */
+ AM62LX_IOPAD(0x01c0, PIN_INPUT, 7) /* (B13) UART0_RTSn.GPIO0_95 */
+ >;
+ };
+
+ i2c0_default_pins: i2c0-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x01cc, PIN_INPUT_PULLUP, 0) /* (B7) I2C0_SCL */
+ AM62LX_IOPAD(0x01d0, PIN_INPUT_PULLUP, 0) /* (A7) I2C0_SDA */
+ >;
+ bootph-all;
+ };
+
+ i2c1_default_pins: i2c1-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x01d4, PIN_INPUT_PULLUP, 0) /* (D7) I2C1_SCL */
+ AM62LX_IOPAD(0x01d8, PIN_INPUT_PULLUP, 0) /* (A6) I2C1_SDA */
+ >;
+ bootph-all;
+ };
+
+ vdd_3v3_sd_ena_default_pins: vdd-3v3-sd-ena-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x07c, PIN_OUTPUT, 7) /* (L23) GPMC0_AD1.GPIO0_16 */
+ >;
+ bootph-all;
+ };
+
+ sensor_3v3_ena_default_pins: sensor-3v3-ena-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x004, PIN_OUTPUT, 7) /* (AA23) WKUP_UART0_TXD.WKUP_GPIO0_1 */
+ >;
+ };
+
+ mmc1_default_pins: mmc1-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x0230, PIN_INPUT, 0) /* (Y3) MMC1_CMD */
+ AM62LX_IOPAD(0x0228, PIN_OUTPUT, 0) /* (Y2) MMC1_CLK */
+ AM62LX_IOPAD(0x0224, PIN_INPUT, 0) /* (AA1) MMC1_DAT0 */
+ AM62LX_IOPAD(0x0220, PIN_INPUT, 0) /* (Y4) MMC1_DAT1 */
+ AM62LX_IOPAD(0x021c, PIN_INPUT, 0) /* (AA2) MMC1_DAT2 */
+ AM62LX_IOPAD(0x0218, PIN_INPUT, 0) /* (AB2) MMC1_DAT3 */
+ AM62LX_IOPAD(0x0234, PIN_INPUT, 0) /* (B6) MMC1_SDCD */
+ >;
+ bootph-all;
+ };
+
+ mmc2_pins_default: mmc2-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x010c, PIN_INPUT, 0) /* (U23) MMC2_CMD */
+ AM62LX_IOPAD(0x0104, PIN_OUTPUT, 0) /* (R23) MMC2_CLK */
+ AM62LX_IOPAD(0x0108, PIN_INPUT, 0) /* () MMC2_CLKLB */
+ AM62LX_IOPAD(0x0100, PIN_INPUT, 0) /* (U22) MMC2_DAT0 */
+ AM62LX_IOPAD(0x00fc, PIN_INPUT, 0) /* (T22) MMC2_DAT1 */
+ AM62LX_IOPAD(0x00f8, PIN_INPUT, 0) /* (T23) MMC2_DAT2 */
+ AM62LX_IOPAD(0x00f4, PIN_INPUT, 0) /* (R22) MMC2_DAT3 */
+ >;
+ };
+
+ wlan_en_pins_default: wlan-en-pins-default {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x0110, PIN_OUTPUT, 7) /* (T20) MMC2_SDCD.GPIO0_51 */
+ >;
+ };
+
+ wlirq_pins_default: wlirq-pins-default {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x0114, PIN_INPUT, 7) /* (T21) MMC2_SDWP.GPIO0_52 */
+ >;
+ };
+
+ usb1_default_pins: usb1-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x0248, PIN_INPUT | PIN_DS_PULLUD_ENABLE | PIN_DS_PULL_UP, 0) /* (A5) USB1_DRVVBUS */
+ >;
+ bootph-all;
+ };
+
+ pwm_beeper_default_pins: pwm-beeper-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x00b0, PIN_OUTPUT, 4) /* (F22) GPMC0_AD14.EHRPWM0_B */
+ >;
+ };
+
+ pmic_irq_default_pins: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x01e8, PIN_INPUT, 0) /* (C8) EXTINTn */
+ >;
+ bootph-all;
+ };
+
+ wkup_i2c0_default_pins: wkup-i2c0-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x0010, PIN_INPUT_PULLUP, 0) /* (AB22) WKUP_I2C0_SCL */
+ AM62LX_IOPAD(0x0014, PIN_INPUT_PULLUP, 0) /* (AA22) WKUP_I2C0_SDA */
+ >;
+ bootph-all;
+ };
+
+ rgb_led_default_pins: rgb-led-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x0190, PIN_OUTPUT, 2) /* (A11) MCASP0_ACLKX.ECAP2_IN_APWM_OUT */
+ AM62LX_IOPAD(0x0188, PIN_OUTPUT, 2) /* (A9) MCASP0_AXR1.ECAP1_IN_APWM_OUT */
+ AM62LX_IOPAD(0x018c, PIN_OUTPUT, 5) /* (B9) MCASP0_AXR0.EHRPWM1_B */
+ >;
+ };
+
+ spi1_pins_default: spi1-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x008c, PIN_OUTPUT, 4) /* (H22) GPMC0_AD5.SPI1_CLK */
+ AM62LX_IOPAD(0x0088, PIN_OUTPUT, 4) /* (K23) GPMC0_AD4.SPI1_CS0 */
+ AM62LX_IOPAD(0x0080, PIN_INPUT, 4) /* (K22) GPMC0_AD2.SPI1_D0 */
+ AM62LX_IOPAD(0x0084, PIN_OUTPUT, 4) /* (J23) GPMC0_AD3.SPI1_D1 */
+ >;
+ bootph-all;
+ };
+
+ spi3_pins_default: spi3-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x00d0, PIN_OUTPUT, 5) /* (P22) GPMC0_BE1n.SPI3_CLK */
+ AM62LX_IOPAD(0x00cc, PIN_OUTPUT, 5) /* (P23) GPMC0_BE0n_CLE.SPI3_CS0 */
+ AM62LX_IOPAD(0x00d4, PIN_INPUT, 5) /* (N23) GPMC0_WAIT0.SPI3_D0 */
+ AM62LX_IOPAD(0x00d8, PIN_OUTPUT, 5) /* (N22) GPMC0_WAIT1.SPI3_D1 */
+ >;
+ };
+
+ mcp23s18_reset_pins_default: mcp23s18-reset-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x00a0, PIN_OUTPUT, 4) /* (H21) GPMC0_AD10.GPIO0_25 */
+ >;
+ };
+
+ lora_control_pins_default: lora-control-default-pins {
+ pinctrl-single,pins = <
+ AM62LX_IOPAD(0x00c8, PIN_OUTPUT, 7) /* (M19) GPMC0_WEn.GPIO0_34 */
+ AM62LX_IOPAD(0x00e4, PIN_OUTPUT, 7) /* (L20) GPMC0_CSn0.GPIO0_41 */
+ AM62LX_IOPAD(0x01a4, PIN_INPUT, 7) /* (D11) SPI0_CS1.GPIO0_88 */
+ AM62LX_IOPAD(0x01bc, PIN_INPUT, 7) /* (B14) UART0_CTSn.GPIO0_94 */
+ >;
+ };
+};
+
+&uart0 {
+ wakeup-source;
+ pinctrl-0 = <&uart0_default_pins>;
+ pinctrl-1 = <&uart0_wakeup_pins>;
+ pinctrl-names = "default", "wakeup";
+ bootph-all;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_default_pins>;
+ bootph-all;
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_default_pins>;
+ bootph-all;
+ status = "okay";
+
+ /* EEPROM */
+ eeprom@50 {
+ /* FT24C32A-ELRT */
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+
+ /* Fuel Gauge */
+ fuel-gauge@55 {
+ compatible = "ti,bq27541";
+ reg = <0x55>;
+ };
+
+ /* IMU Sensor */
+ accelerometer@6a {
+ compatible = "st,lsm6ds3tr-c";
+ reg = <0x6a>;
+ vdd-supply = <&vcc_3v3_main>;
+ vddio-supply = <&vcc_3v3_main>;
+ };
+
+ /* T&H Sensor */
+ th-sensor@44 {
+ compatible = "sensirion,sht4x";
+ reg = <0x44>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_default_pins>;
+ bootph-all;
+ status = "okay";
+};
+
+&wkup_i2c0 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_i2c0_default_pins>;
+ status = "okay";
+
+ tps65214: pmic@30 {
+ compatible = "ti,tps65214";
+ reg = <0x30>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ buck1-supply = <&vcc_3v3_main>;
+ buck2-supply = <&vcc_3v3_main>;
+ buck3-supply = <&vcc_3v3_main>;
+ ldo1-supply = <&vcc_3v3_main>;
+ ldo2-supply = <&vcc_3v3_main>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_default_pins>;
+ ti,power-button;
+
+ regulators {
+ buck1_reg: buck1 {
+ regulator-name = "VDD_CORE";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: buck2 {
+ regulator-name = "VDD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: buck3 {
+ regulator-name = "VDD_LPDDR4";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo1_reg: ldo1 {
+ regulator-name = "VDDA_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-name = "PMIC_VDD_RTC";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&gpio0 {
+ gpio-line-names ="","","","","","","","","","", /* 0-9 */
+ "","","","","","","VDD_3V3_SD_ENA","","","", /* 10-19 */
+ "","","","","","MCP23S18_RESET","USR0","","","", /* 20-29 */
+ "","USR1","USR2","","LORA_RESET","","","","","", /* 30-39 */
+ "","LORA_RFSW","USR3","","","","","","","", /* 40-49 */
+ "","VDD_WLAN_EN","WL_IRQ","","","","","","","", /* 50-59 */
+ "","","","","","","","","","", /* 60-69 */
+ "","","","","","","","","","", /* 70-79 */
+ "","","","","","","","","LORA_BUSY","", /* 80-89 */
+ "","","","","LORA_DIO","USR4","","","","", /* 90-99 */
+ "","","","","USR5","","","","",""; /* 100-109 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&lora_control_pins_default>;
+ bootph-all;
+ status = "okay";
+};
+
+&gpio2 {
+ bootph-all;
+ status = "okay";
+};
+
+&wkup_gpio0 {
+ gpio-line-names ="","SENSOR_3V3_ENA","","","","","",""; /* 0-7 */
+ bootph-all;
+ status = "okay";
+};
+
+&sdhci1 {
+ /* SD/MMC */
+ vmmc-supply = <&vdd_3v3_sd>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_default_pins>;
+ bootph-all;
+ status = "okay";
+};
+
+&sdhci2 {
+ vmmc-supply = <&wlan_en>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ ti,fails-without-test-cd;
+ status = "okay";
+
+ wlcore: wlcore@2 {
+ compatible = "ti,cc3300";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <52 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlirq_pins_default>;
+ };
+};
+
+&epwm0 {
+ status = "okay";
+};
+
+&epwm1 {
+ status = "okay";
+};
+
+&ecap1 {
+ status = "okay";
+};
+
+&ecap2 {
+ status = "okay";
+};
+
+&usbss0 {
+ ti,vbus-divider;
+ status = "okay";
+};
+
+&usb0 {
+ usb-role-switch;
+ bootph-all;
+ status = "okay";
+};
+
+&usbss1 {
+ ti,vbus-divider;
+ bootph-all;
+ status = "okay";
+};
+
+&usb1 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_default_pins>;
+ bootph-all;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins_default>;
+ status = "okay";
+
+ mcp23s18: gpio@0 {
+ compatible = "microchip,mcp23s18";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ reset-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcp23s18_reset_pins_default>;
+ microchip,spi-present-mask = <0x01>;
+ };
+};
+
+&spi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins_default>;
+ status = "okay";
+
+ sx1262_lora: lora@0 {
+ compatible = "rohm,dh2228fv";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ };
+};
--
2.53.0
prev parent reply other threads:[~2026-05-01 23:31 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-01 23:31 [PATCH 0/2] arm64: dts/bindings: Add support for BeagleBadge Judith Mendez
2026-05-01 23:31 ` [PATCH 1/2] dt-bindings: arm: ti: Add am62l3-badge Judith Mendez
2026-05-01 23:31 ` Judith Mendez [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260501233148.4180391-3-jm@ti.com \
--to=jm@ti.com \
--cc=afd@ti.com \
--cc=bb@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox