From: Rudraksha Gupta via B4 Relay <devnull+guptarud.gmail.com@kernel.org>
To: Lee Jones <lee@kernel.org>, Pavel Machek <pavel@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Linus Walleij <linusw@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>
Cc: linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
phone-devel@vger.kernel.org,
Rudraksha Gupta <guptarud@gmail.com>
Subject: [PATCH v5 2/3] leds: flash: rt8515: Support single-GPIO flash ICs with vin supply
Date: Sun, 03 May 2026 14:43:16 -0700 [thread overview]
Message-ID: <20260503-expressatt_camera_flash-v5-2-95524506a799@gmail.com> (raw)
In-Reply-To: <20260503-expressatt_camera_flash-v5-0-95524506a799@gmail.com>
From: Rudraksha Gupta <guptarud@gmail.com>
Extend the RT8515 driver to support flash ICs that use only a single
GPIO for both flash and torch modes (no separate ENT pin), with an
optional vin regulator that gates power to the flash IC.
When vin-supply is provided, the driver enables the regulator before
activating the LED and disables it when turning off.
Make ent-gpios optional. When ent-gpios is absent, the driver uses
enf-gpios for both flash and torch brightness control.
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
---
drivers/leds/flash/leds-rt8515.c | 130 +++++++++++++++++++++++++++++++--------
1 file changed, 105 insertions(+), 25 deletions(-)
diff --git a/drivers/leds/flash/leds-rt8515.c b/drivers/leds/flash/leds-rt8515.c
index f6b439674c03..4459874e6a6c 100644
--- a/drivers/leds/flash/leds-rt8515.c
+++ b/drivers/leds/flash/leds-rt8515.c
@@ -31,6 +31,7 @@
#include <linux/platform_device.h>
#include <linux/property.h>
#include <linux/regulator/consumer.h>
+#include <linux/workqueue.h>
#include <media/v4l2-flash-led-class.h>
@@ -52,7 +53,7 @@ struct rt8515 {
struct regulator *reg;
struct gpio_desc *enable_torch;
struct gpio_desc *enable_flash;
- struct timer_list powerdown_timer;
+ struct delayed_work powerdown_work;
u32 max_timeout; /* Flash max timeout */
int flash_max_intensity;
int torch_max_intensity;
@@ -63,16 +64,50 @@ static struct rt8515 *to_rt8515(struct led_classdev_flash *fled)
return container_of(fled, struct rt8515, fled);
}
-static void rt8515_gpio_led_off(struct rt8515 *rt)
+static int rt8515_gpio_led_off(struct rt8515 *rt)
{
+ int ret;
+
gpiod_set_value(rt->enable_flash, 0);
gpiod_set_value(rt->enable_torch, 0);
+
+ if (!rt->reg)
+ return 0;
+
+ /* Disable regulator */
+ ret = regulator_is_enabled(rt->reg);
+ if (ret < 0)
+ return ret;
+ if (ret > 0)
+ return regulator_disable(rt->reg);
+
+ return 0;
}
-static void rt8515_gpio_brightness_commit(struct gpio_desc *gpiod,
- int brightness)
+static int rt8515_gpio_brightness_commit(struct rt8515 *rt,
+ struct gpio_desc *gpiod,
+ int brightness)
{
int i;
+ int ret;
+
+ /*
+ * Reset the IC to start brightness from zero,
+ * then re-enable and pulse to the desired level.
+ */
+ ret = rt8515_gpio_led_off(rt);
+ if (ret)
+ return ret;
+
+ /* IC needs time to reset its brightness counter */
+ usleep_range(100, 200);
+
+ /* Enable regulator */
+ if (rt->reg) {
+ ret = regulator_enable(rt->reg);
+ if (ret)
+ return ret;
+ }
/*
* Toggling a GPIO line with a small delay increases the
@@ -84,6 +119,8 @@ static void rt8515_gpio_brightness_commit(struct gpio_desc *gpiod,
gpiod_set_value(gpiod, 1);
udelay(1);
}
+
+ return 0;
}
/* This is setting the torch light level */
@@ -92,23 +129,38 @@ static int rt8515_led_brightness_set(struct led_classdev *led,
{
struct led_classdev_flash *fled = lcdev_to_flcdev(led);
struct rt8515 *rt = to_rt8515(fled);
+ int ret = 0;
mutex_lock(&rt->lock);
if (brightness == LED_OFF) {
/* Off */
- rt8515_gpio_led_off(rt);
+ ret = rt8515_gpio_led_off(rt);
+ if (ret)
+ goto out;
} else if (brightness < RT8515_TORCH_MAX) {
- /* Step it up to movie mode brightness using the flash pin */
- rt8515_gpio_brightness_commit(rt->enable_torch, brightness);
+ /*
+ * Step it up to movie mode brightness.
+ * If there is no separate torch pin, use the flash pin
+ * for torch as well.
+ */
+ ret = rt8515_gpio_brightness_commit(rt,
+ rt->enable_torch ?: rt->enable_flash, brightness);
+ if (ret)
+ goto out;
} else {
- /* Max torch brightness requested */
- gpiod_set_value(rt->enable_torch, 1);
+ /*
+ * Max torch brightness requested.
+ * If there is no separate torch pin, use the flash pin
+ * for torch as well.
+ */
+ gpiod_set_value(rt->enable_torch ?: rt->enable_flash, 1);
}
+out:
mutex_unlock(&rt->lock);
- return 0;
+ return ret;
}
static int rt8515_led_flash_strobe_set(struct led_classdev_flash *fled,
@@ -117,27 +169,34 @@ static int rt8515_led_flash_strobe_set(struct led_classdev_flash *fled,
struct rt8515 *rt = to_rt8515(fled);
struct led_flash_setting *timeout = &fled->timeout;
int brightness = rt->flash_max_intensity;
+ int ret = 0;
mutex_lock(&rt->lock);
if (state) {
/* Enable LED flash mode and set brightness */
- rt8515_gpio_brightness_commit(rt->enable_flash, brightness);
+ ret = rt8515_gpio_brightness_commit(rt, rt->enable_flash, brightness);
+ if (ret)
+ goto out;
+
/* Set timeout */
- mod_timer(&rt->powerdown_timer,
- jiffies + usecs_to_jiffies(timeout->val));
+ schedule_delayed_work(&rt->powerdown_work,
+ usecs_to_jiffies(timeout->val));
} else {
- timer_delete_sync(&rt->powerdown_timer);
+ cancel_delayed_work(&rt->powerdown_work);
/* Turn the LED off */
- rt8515_gpio_led_off(rt);
+ ret = rt8515_gpio_led_off(rt);
+ if (ret)
+ goto out;
}
fled->led_cdev.brightness = LED_OFF;
/* After this the torch LED will be disabled */
+out:
mutex_unlock(&rt->lock);
- return 0;
+ return ret;
}
static int rt8515_led_flash_strobe_get(struct led_classdev_flash *fled,
@@ -145,7 +204,7 @@ static int rt8515_led_flash_strobe_get(struct led_classdev_flash *fled,
{
struct rt8515 *rt = to_rt8515(fled);
- *state = timer_pending(&rt->powerdown_timer);
+ *state = delayed_work_pending(&rt->powerdown_work);
return 0;
}
@@ -163,12 +222,18 @@ static const struct led_flash_ops rt8515_flash_ops = {
.timeout_set = rt8515_led_flash_timeout_set,
};
-static void rt8515_powerdown_timer(struct timer_list *t)
+static void rt8515_powerdown_work(struct work_struct *work)
{
- struct rt8515 *rt = timer_container_of(rt, t, powerdown_timer);
+ struct rt8515 *rt = container_of(work, struct rt8515, powerdown_work.work);
+ int ret;
/* Turn the LED off */
- rt8515_gpio_led_off(rt);
+ mutex_lock(&rt->lock);
+ ret = rt8515_gpio_led_off(rt);
+ mutex_unlock(&rt->lock);
+
+ if (ret)
+ dev_err(rt->dev, "failed to turn off LED (%d)\n", ret);
}
static void rt8515_init_flash_timeout(struct rt8515 *rt)
@@ -298,12 +363,22 @@ static int rt8515_probe(struct platform_device *pdev)
return dev_err_probe(dev, PTR_ERR(rt->enable_flash),
"cannot get ENF (enable flash) GPIO\n");
- /* ENT - Enable Torch line */
- rt->enable_torch = devm_gpiod_get(dev, "ent", GPIOD_OUT_LOW);
+ /* ENT - Enable Torch line (optional for single-GPIO flash ICs) */
+ rt->enable_torch = devm_gpiod_get_optional(dev, "ent", GPIOD_OUT_LOW);
if (IS_ERR(rt->enable_torch))
return dev_err_probe(dev, PTR_ERR(rt->enable_torch),
"cannot get ENT (enable torch) GPIO\n");
+ /* Optional VIN supply */
+ rt->reg = devm_regulator_get_optional(dev, "vin");
+ if (IS_ERR(rt->reg)) {
+ ret = PTR_ERR(rt->reg);
+ if (ret != -ENODEV)
+ return dev_err_probe(dev, ret,
+ "failed to get vin supply\n");
+ rt->reg = NULL;
+ }
+
child = device_get_next_child_node(dev, NULL);
if (!child) {
dev_err(dev,
@@ -328,12 +403,17 @@ static int rt8515_probe(struct platform_device *pdev)
dev_warn(dev,
"flash-max-timeout-us property missing\n");
}
- timer_setup(&rt->powerdown_timer, rt8515_powerdown_timer, 0);
+ INIT_DELAYED_WORK(&rt->powerdown_work, rt8515_powerdown_work);
rt8515_init_flash_timeout(rt);
fled->ops = &rt8515_flash_ops;
- led->max_brightness = rt->torch_max_intensity;
+ /*
+ * If there is no separate torch pin, use the flash max intensity
+ * as the max brightness instead.
+ */
+ led->max_brightness = rt->enable_torch ?
+ rt->torch_max_intensity : rt->flash_max_intensity;
led->brightness_set_blocking = rt8515_led_brightness_set;
led->flags |= LED_CORE_SUSPENDRESUME | LED_DEV_CAP_FLASH;
@@ -372,7 +452,7 @@ static void rt8515_remove(struct platform_device *pdev)
struct rt8515 *rt = platform_get_drvdata(pdev);
rt8515_v4l2_flash_release(rt);
- timer_delete_sync(&rt->powerdown_timer);
+ cancel_delayed_work_sync(&rt->powerdown_work);
mutex_destroy(&rt->lock);
}
--
2.54.0
next prev parent reply other threads:[~2026-05-03 21:43 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-03 21:43 [PATCH v5 0/3] Samsung Expressatt: Camera Flash Rudraksha Gupta via B4 Relay
2026-05-03 21:43 ` [PATCH v5 1/3] dt-bindings: leds: rt8515: Support single-GPIO flash ICs with vin supply Rudraksha Gupta via B4 Relay
2026-05-03 21:43 ` Rudraksha Gupta via B4 Relay [this message]
2026-05-03 21:43 ` [PATCH v5 3/3] ARM: dts: qcom: msm8960: expressatt: Add camera flash Rudraksha Gupta via B4 Relay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260503-expressatt_camera_flash-v5-2-95524506a799@gmail.com \
--to=devnull+guptarud.gmail.com@kernel.org \
--cc=andersson@kernel.org \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=guptarud@gmail.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=lee@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linusw@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=pavel@kernel.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox