[PATCH 2/4] arm64: dts: renesas: add support for solidrun rzg2l som and hb-iiot evb

[Josua Mayer <josua@solid-run.com>]

Add support for the SolidRun RZ/G2L SoM on Hummingboard IIoT.

The SoM features:
- 2x 1Gbps Ethernet with PHY
- eMMC
- 1/2GB DDR
- WiFi + Bluetooth
- SDHI Mux switching between eMMC and Carrier Board

The HummingBoard IIoT features:
- 3x USB-2.0 Type A connector
- 2x 1Gbps RJ45 Ethernet
- USB Type-C Console Port
- microSD connector
- RTC with backup battery
- RGB Status LED
- 1x M.2 B-Key connector with USB-2.0 + SIM card holder
- 1x DSI Display Connector
- GPIO header
- 2x RS232/RS485 ports (configurable)
- 2x CAN

Descriptions for eMMC, microSD and RS485 are provided as overlays due to
their dependency on configurable mux states.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 arch/arm64/boot/dts/renesas/Makefile               |  13 +
 .../dts/renesas/r9a07g044l2-hummingboard-iiot.dts  |  16 +
 .../renesas/rzg2l-hummingboard-iiot-common.dtsi    | 580 +++++++++++++++++++++
 .../renesas/rzg2l-hummingboard-iiot-microsd.dtso   |  26 +
 .../renesas/rzg2l-hummingboard-iiot-rs485-a.dtso   |  21 +
 .../renesas/rzg2l-hummingboard-iiot-rs485-b.dtso   |  21 +
 .../boot/dts/renesas/rzg2l-hummingboard-iiot.dtsi  |  49 ++
 arch/arm64/boot/dts/renesas/rzg2l-sr-som-emmc.dtso |  44 ++
 arch/arm64/boot/dts/renesas/rzg2l-sr-som.dtsi      | 420 +++++++++++++++
 9 files changed, 1190 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index ca45d2857ea7f..37cfefe66a308 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -169,6 +169,19 @@ dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044c2-smarc-cru-csi-ov5645.dtbo
 r9a07g044c2-smarc-cru-csi-ov5645-dtbs := r9a07g044c2-smarc.dtb r9a07g044c2-smarc-cru-csi-ov5645.dtbo
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044c2-smarc-cru-csi-ov5645.dtb
 
+dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-hummingboard-iiot.dtb
+dtb-$(CONFIG_ARCH_R9A07G044) += rzg2l-sr-som-emmc.dtbo
+r9a07g044l2-hummingboard-iiot-emmc-dtbs += r9a07g044l2-hummingboard-iiot.dtb rzg2l-sr-som-emmc.dtbo
+dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-hummingboard-iiot-emmc.dtb
+dtb-$(CONFIG_ARCH_R9A07G044) += rzg2l-hummingboard-iiot-microsd.dtbo
+r9a07g044l2-hummingboard-iiot-microsd-dtbs += r9a07g044l2-hummingboard-iiot.dtb rzg2l-hummingboard-iiot-microsd.dtbo
+dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-hummingboard-iiot-microsd.dtb
+dtb-$(CONFIG_ARCH_R9A07G044) += rzg2l-hummingboard-iiot-rs485-a.dtbo
+r9a07g044l2-hummingboard-iiot-rs485-a-dtbs += r9a07g044l2-hummingboard-iiot.dtb rzg2l-hummingboard-iiot-rs485-a.dtbo
+dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-hummingboard-iiot-rs485-a.dtb
+dtb-$(CONFIG_ARCH_R9A07G044) += rzg2l-hummingboard-iiot-rs485-b.dtbo
+r9a07g044l2-hummingboard-iiot-rs485-b-dtbs += r9a07g044l2-hummingboard-iiot.dtb rzg2l-hummingboard-iiot-rs485-b.dtbo
+dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-hummingboard-iiot-rs485-b.dtb
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-remi-pi.dtb
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-smarc.dtb
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-smarc-cru-csi-ov5645.dtbo
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044l2-hummingboard-iiot.dts b/arch/arm64/boot/dts/renesas/r9a07g044l2-hummingboard-iiot.dts
new file mode 100644
index 0000000000000..eba4f423c8f05
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g044l2-hummingboard-iiot.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright 2025 Josua Mayer <josua@solid-run.com>
+ */
+
+/dts-v1/;
+
+#include "r9a07g044l2.dtsi"
+#include "rzg2l-sr-som.dtsi"
+#include "rzg2l-hummingboard-iiot.dtsi"
+
+/ {
+	compatible = "solidrun,rzg2l-hummingboard-iiot", "solidrun,rzg2l-sr-som",
+		     "renesas,r9a07g044l2", "renesas,r9a07g044";
+	model = "SolidRun RZ/G2L HummingBoard IIoT";
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-common.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-common.dtsi
new file mode 100644
index 0000000000000..ff2c42bcffe2f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-common.dtsi
@@ -0,0 +1,580 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright 2025 Josua Mayer <josua@solid-run.com>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+/ {
+	/* power for M.2 B-Key connector (J6) */
+	regulator-m2-b {
+		compatible = "regulator-fixed";
+		regulator-name = "m2-b";
+		gpios = <&tca6416_u20 5 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	/* power for M.2 M-Key connector (J4) */
+	regulator-m2-m {
+		compatible = "regulator-fixed";
+		regulator-name = "m2-m";
+		gpios = <&tca6416_u20 6 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	/* power for USB-A J27 behind USB Hub Port 3 */
+	regulator-vbus-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus2";
+		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		gpio = <&tca6416_u20 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	/* power for USB-A J27 behind USB Hub Port 4 */
+	regulator-vbus-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus3";
+		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		gpio = <&tca6416_u20 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	aliases {
+		gpio1 = &tca6408_u48;
+		gpio2 = &tca6408_u37;
+		gpio3 = &tca6416_u20;
+		gpio4 = &tca6416_u21;
+		i2c3 = &i2c_exp;
+		i2c4 = &i2c_csi;
+		i2c5 = &i2c_dsi;
+		i2c6 = &i2c_lvds;
+		rtc0 = &carrier_rtc;
+		rtc1 = &pmic;
+		serial3 = &scif3;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		wakeup-event {
+			interrupts-extended = <&tca6416_u21 11 IRQ_TYPE_EDGE_FALLING>;
+			label = "m2-m-wakeup";
+			wakeup-source;
+			linux,code = <KEY_WAKEUP>;
+		};
+	};
+
+	can_mux: mux-controller-1 {
+		compatible = "gpio-mux";
+		/* default J9-55/57/59/61 to on-board transceivers */
+		idle-state = <0>;
+		#mux-control-cells = <0>;
+		/*
+		 * Mux routes CAN bus signals between SoM connector pins,
+		 * expansion connector (J22) and on-board transceivers using
+		 * two GPIO:
+		 * - IO3: 0 = on-board transceivers, 1 = expansion connector
+		 * - IO4: 0 = J9-55/57/59/61, 1 = J7-12/16 & J9-54/56
+		 */
+		mux-gpios = <&tca6416_u20 3 GPIO_ACTIVE_HIGH>,
+			    <&tca6416_u20 4 GPIO_ACTIVE_HIGH>;
+	};
+
+	spi_mux: mux-controller-2 {
+		compatible = "gpio-mux";
+		/* default on-board */
+		idle-state = <0>;
+		/*
+		 * Mux switches spi bus between on-board tpm
+		 * and expansion connector (J22).
+		 */
+		mux-gpios = <&tca6416_u21 0 GPIO_ACTIVE_HIGH>;
+		#mux-control-cells = <0>;
+	};
+
+	scif1_scif3_b2b_mux: mux-controller-3 {
+		compatible = "gpio-mux";
+		/* default on-board */
+		idle-state = <0>;
+		#mux-control-cells = <0>;
+		/*
+		 * Mux switches both scif1 and scif3 tx/rx between expansion
+		 * connector (J22) and on-board rs232/rs485 transceivers
+		 * using one GPIO: 0 = on-board, 1 = connector.
+		 */
+		mux-gpios = <&tca6416_u20 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	scif1_rs_232_485_mux: mux-controller-4 {
+		compatible = "gpio-mux";
+		/* default rs232 */
+		idle-state = <0>;
+		#mux-control-cells = <0>;
+		/*
+		 * Mux switches scif1 tx/rx between rs232 and rs485
+		 * transceivers. using one GPIO: 0 = rs232, 1 = rs485.
+		 */
+		mux-gpios = <&tca6416_u20 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	scif3_rs_232_485_mux: mux-controller-5 {
+		compatible = "gpio-mux";
+		/* default rs232 */
+		idle-state = <0>;
+		#mux-control-cells = <0>;
+		/*
+		 * Mux switches scif3 tx/rx between rs232 and rs485
+		 * transceivers. using one GPIO: 0 = rs232, 1 = rs485.
+		 */
+		mux-gpios = <&tca6416_u20 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	v_1_2: regulator-1-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v2";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+	};
+
+	v_3_3: regulator-3-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+	};
+
+	reg_dsi_panel: regulator-dsi-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "dsi-panel";
+		gpios = <&tca6416_u20 15 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <11200000>;
+		regulator-min-microvolt = <11200000>;
+		enable-active-high;
+	};
+
+	vmmc: regulator-mmc {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		startup-delay-us = <250>;
+		vin-supply = <&v_3_3>;
+		gpio = <&pinctrl RZG2L_GPIO(4, 1) GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
+
+	/* power for USB-A J5003 */
+	vbus1: regulator-vbus-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus1";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		gpio = <&tca6416_u20 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	rfkill-m2-b-gnss {
+		compatible = "rfkill-gpio";
+		/* rfkill-gpio inverts internally */
+		shutdown-gpios = <&tca6416_u20 10 GPIO_ACTIVE_HIGH>;
+		label = "m2-b gnss";
+		radio-type = "gps";
+	};
+
+	rfkill-m2-b-wwan {
+		compatible = "rfkill-gpio";
+		/* rfkill-gpio inverts internally */
+		shutdown-gpios = <&tca6416_u20 9 GPIO_ACTIVE_HIGH>;
+		label = "m2-b radio";
+		radio-type = "wwan";
+	};
+};
+
+&ehci1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub_2_0: hub@1 {
+		compatible = "usb4b4,6502", "usb4b4,6506";
+		reg = <1>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&tca6416_u20 11 GPIO_ACTIVE_LOW>;
+		vdd2-supply = <&v_3_3>;
+		vdd-supply = <&v_1_2>;
+	};
+
+	/* this device is not visible because host supports 2.0 only */
+	hub_3_0: hub@2 {
+		compatible = "usb4b4,6500", "usb4b4,6504";
+		reg = <2>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&tca6416_u20 11 GPIO_ACTIVE_LOW>;
+		vdd2-supply = <&v_3_3>;
+		vdd-supply = <&v_1_2>;
+	};
+};
+
+&i2c0 {
+	/* highest i2c clock supported by all peripherals is 400kHz */
+
+	tca6416_u20: gpio@20 {
+		compatible = "ti,tcal6416";
+		reg = <0x20>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-line-names = "TCA_INT/EXT_UART", "TCA_UARTA_232/485",
+				  "TCA_UARTB_232/485", "TCA_INT/EXT_CAN",
+				  "TCA_NXP/REN", "TCA_M.2B_3V3_EN",
+				  "TCA_M.2M_3V3_EN", "TCA_M.2M_RESET#",
+				  "TCA_M.2B_RESET#", "TCA_M.2B_W_DIS#",
+				  "TCA_M.2B_GPS_EN#", "TCA_USB-HUB_RST#",
+				  "TCA_USB_HUB3_PWR_EN", "TCA_USB_HUB4_PWR_EN",
+				  "TCA_USB1_PWR_EN", "TCA_VIDEO_PWR_EN";
+
+		m2-b-reset-hog {
+			gpios = <8 GPIO_ACTIVE_LOW>;
+			gpio-hog;
+			line-name = "m2-b-reset";
+			output-low;
+		};
+
+		m2-m-reset-hog {
+			gpios = <7 GPIO_ACTIVE_LOW>;
+			gpio-hog;
+			line-name = "m2-m-reset";
+			/*
+			 * M.2 Key-M connector only supports PCI,
+			 * but RZ/G2L(C) has no pci controller.
+			 * Keep any card in reset.
+			 */
+			output-high;
+		};
+	};
+
+	tca6416_u21: gpio@21 {
+		compatible = "ti,tcal6416";
+		reg = <0x21>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-line-names = "TCA_SPI_TPM/EXT", "TCA_TPM_RST#",
+				  "TCA_I2C_RST", "TCA_RS232_SHTD#",
+				  "TCA_LCD_I2C_RST", "TCA_DIG_OUT1",
+				  "TCA_bDIG_IN1", "TCA_SENS_INT",
+				  "TCA_ALERT#", "TCA_TPM_PIRQ#",
+				  "TCA_RTC_INT", "TCA_M.2M_WAKW_ON_LAN",
+				  "TCA_M.2M_CLKREQ#", "TCA_LVDS_INT#",
+				  "", "TCA_POE_AT";
+		interrupts-extended = <&pinctrl RZG2L_GPIO(4, 0) IRQ_TYPE_EDGE_FALLING>;
+
+		lcd-i2c-reset-hog {
+			gpios = <4 (GPIO_ACTIVE_LOW|GPIO_PULL_UP|GPIO_OPEN_DRAIN)>;
+			line-name = "lcd-i2c-reset";
+			output-low;
+			/*
+			 * reset shared between U37 and U48, to be
+			 * supported once gpio-pca953x switches to
+			 * reset framework.
+			 */
+			gpio-hog;
+		};
+
+		lvds-irq-hog {
+			gpios = <13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP | GPIO_OPEN_DRAIN)>;
+			gpio-hog;
+			input;
+			line-name = "lvds-irq";
+		};
+
+		m2-m-clkreq-hog {
+			gpios = <12 GPIO_ACTIVE_LOW>;
+			gpio-hog;
+			input;
+			line-name = "m2-m-clkreq";
+		};
+
+		rs232_shutdown: rs232-shutdown-hog {
+			gpios = <3 GPIO_ACTIVE_LOW>;
+			gpio-hog;
+			line-name = "rs232-shutdown";
+			output-low;
+		};
+
+		sensor-irq-hog {
+			gpios = <7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP | GPIO_OPEN_DRAIN)>;
+			gpio-hog;
+			input;
+			line-name = "sensor-irq";
+		};
+
+		tpm-irq-hog {
+			gpios = <9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP | GPIO_OPEN_DRAIN)>;
+			gpio-hog;
+			input;
+			line-name = "tpm-irq";
+		};
+	};
+
+	led-controller@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* use internal clock, could use external generated by rtc */
+		clock-mode = /bits/ 8 <1>;
+
+		multi-led@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			color = <LED_COLOR_ID_RGB>;
+			label = "D7";
+
+			led@0 {
+				reg = <0x0>;
+				color = <LED_COLOR_ID_RED>;
+				led-cur = /bits/ 8 <0x32>;
+				max-cur = /bits/ 8 <0x64>;
+			};
+
+			led@1 {
+				reg = <0x1>;
+				color = <LED_COLOR_ID_GREEN>;
+				led-cur = /bits/ 8 <0x19>;
+				max-cur = /bits/ 8 <0x32>;
+			};
+
+			led@2 {
+				reg = <0x2>;
+				color = <LED_COLOR_ID_BLUE>;
+				led-cur = /bits/ 8 <0x19>;
+				max-cur = /bits/ 8 <0x32>;
+			};
+		};
+
+		led@3 {
+			reg = <0x3>;
+			chan-name = "D8";
+			color = <LED_COLOR_ID_GREEN>;
+			label = "D8";
+			led-cur = /bits/ 8 <0x19>;
+			max-cur = /bits/ 8 <0x64>;
+		};
+	};
+
+	light-sensor@44 {
+		compatible = "isil,isl29023";
+		reg = <0x44>;
+		/* IRQ shared between accelerometer, light-sensor and Tamper input (J5007) */
+		interrupts-extended = <&tca6416_u21 7 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	accelerometer@53 {
+		compatible = "adi,adxl345";
+		reg = <0x53>;
+		interrupts-extended = <&tca6416_u21 7 IRQ_TYPE_EDGE_FALLING>;
+		/* IRQ shared between accelerometer, light-sensor and Tamper input (J5007) */
+		interrupt-names = "INT1";
+	};
+
+	carrier_eeprom: eeprom@57 {
+		compatible = "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <8>;
+	};
+
+	carrier_rtc: rtc@69 {
+		compatible = "abracon,ab1805";
+		reg = <0x69>;
+		/*
+		 * AM1805 RTC used on this board has only nTIRQ pins wired,
+		 * which is for countdown timer irqs only.
+		 * Driver does not support this, disable for now.
+		 *
+		 * interrupts-extended = <&tca6416_u21 10 IRQ_TYPE_EDGE_FALLING>;
+		 */
+		abracon,tc-diode = "schottky";
+		abracon,tc-resistor = <3>;
+	};
+};
+
+&i2c1 {
+	/* highest i2c clock supported by all peripherals is 400kHz */
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/*
+		 * This reset is open drain,
+		 * but reset core does not support GPIO_OPEN_DRAIN flag.
+		 */
+		reset-gpios = <&tca6416_u21 2 GPIO_ACTIVE_LOW>;
+
+		/* channel 0 routed to expansion connector (J22) */
+		i2c_exp: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		/* channel 1 routed to mipi-csi connector (J23) */
+		i2c_csi: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		/* channel 2 routed to mipi-dsi connector (J25) */
+		i2c_dsi: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tca6408_u48: gpio@21 {
+				compatible = "ti,tca6408";
+				reg = <0x21>;
+				#gpio-cells = <2>;
+				gpio-line-names = "CAM_RST#", "DSI_RESET",
+						  "DSI_STBYB", "DSI_PWM_BL",
+						  "DSI_L/R", "DSI_U/D",
+						  "DSI_CTP_/RST", "CAM_TRIG";
+				/*
+				 * reset shared between U37 and U48, to be
+				 * supported once gpio-pca953x switches to
+				 * reset framework.
+				 *
+				 * reset-gpios = <&tca6416_u21 4
+				 *                (GPIO_ACTIVE_LOW|GPIO_PULL_UP|GPIO_OPEN_DRAIN)>;
+				 */
+				gpio-controller;
+			};
+		};
+
+		/* channel 2 routed to lvds connector (J24) */
+		i2c_lvds: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tca6408_u37: gpio@20 {
+				compatible = "ti,tca6408";
+				reg = <0x20>;
+				#gpio-cells = <2>;
+				gpio-line-names = "SELB", "LVDS_RESET",
+						  "LVDS_STBYB", "LVDS_PWM_BL",
+						  "LVDS_L/R", "LVDS_U/D",
+						  "LVDS_CTP_/RST", "";
+				/*
+				 * reset shared between U37 and U48, to be
+				 * supported once gpio-pca953x switches to
+				 * reset framework.
+				 *
+				 * reset-gpios = <&tca6416_u21 4
+				 *                (GPIO_ACTIVE_LOW|GPIO_PULL_UP|GPIO_OPEN_DRAIN)>;
+				 */
+				gpio-controller;
+			};
+		};
+	};
+};
+
+&phy0 {
+	leds {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* LED_0 pin */
+		led@0 {
+			reg = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "keep";
+			function = LED_FUNCTION_LAN;
+		};
+	};
+};
+
+&pinctrl {
+	/* UARTA */
+	scif1_pins: scif1 {
+		pinmux = <RZG2L_PORT_PINMUX(40, 1, 1)>, /* SCIF1_RXD */
+			 <RZG2L_PORT_PINMUX(40, 0, 1)>; /* SCIF1_TXD */
+	};
+
+	/* UARTA_RTS */
+	scif1_rts_pins: scif1-rts {
+		pinmux = <RZG2L_PORT_PINMUX(41, 1, 0)>; /* P41_1 */
+	};
+
+	/* UARTB */
+	scif3_pins: scif3 {
+		pinmux = <RZG2L_PORT_PINMUX(0, 1, 5)>, /* SCIF3_RXD */
+			 <RZG2L_PORT_PINMUX(0, 0, 5)>; /* SCIF3_TXD */
+	};
+
+	/* UARTB_RTS */
+	scif3_rts_pins: scif3-rts {
+		pinmux = <RZG2L_PORT_PINMUX(41, 0, 0)>; /* P41_0 */
+	};
+};
+
+&scif1 {
+	pinctrl-0 = <&scif1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&scif3 {
+	pinctrl-0 = <&scif3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&spi1 {
+	/* native cs does not support cs persistence required for tpm */
+	cs-gpios = <&pinctrl RZG2L_GPIO(44, 3) GPIO_ACTIVE_LOW>;
+	num-cs = <1>;
+	pinctrl-0 = <&spi1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	spi1_muxed: spi@0 {
+		compatible = "spi-mux";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-controls = <&spi_mux>;
+		/* mux bandwidth is 2GHz, soc max. spi clock is P0/2 = 50MHz */
+		spi-max-frequency = <50000000>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			reg = <0>;
+			interrupts-extended = <&tca6416_u21 9 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&tca6416_u21 1 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+			spi-max-frequency = <43000000>;
+		};
+	};
+};
+
+&usb2_phy0 {
+	dr_mode = "host";
+	vbus-supply = <&vbus1>;
+};
+
+&usb2_phy1 {
+	dr_mode = "host";
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-microsd.dtso b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-microsd.dtso
new file mode 100644
index 0000000000000..aa85054efa0c4
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-microsd.dtso
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+* Device Tree Overlay for the RZ/G2L(C) Solidrun SOM SD
+*
+* Copyright (C) 2024 SolidRun Ltd.
+*/
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+&sdhi0 {
+	bus-width = <4>;
+	full-pwr-cycle;
+	mux-states = <&sdhi0_mux 1>;
+	pinctrl-0 = <&sdhi0_pins>, <&sdhi0_cd_pins>;
+	pinctrl-1 = <&sdhi0_uhs_pins>, <&sdhi0_cd_pins>;
+	pinctrl-names = "default", "state_uhs";
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	vmmc-supply = <&vmmc>;
+	vqmmc-supply = <&reg_pmic_ldo1>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-rs485-a.dtso b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-rs485-a.dtso
new file mode 100644
index 0000000000000..886f4d4ecd67f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-rs485-a.dtso
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright 2025 Josua Mayer <josua@solid-run.com>
+ *
+ * Overlay for enabling HummingBoard IIoT on-board RS485 Port A on connector J5004.
+ *
+ * Because Renesas uart driver does not support rs485,
+ * users must manually toggle P41_1 between RX & TX.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&scif1 {
+	pinctrl-0 = <&scif1_pins>, <&scif1_rts_pins>;
+};
+
+&scif1_rs_232_485_mux {
+	/* select rs485 */
+	idle-state = <1>;
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-rs485-b.dtso b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-rs485-b.dtso
new file mode 100644
index 0000000000000..9cad7e2834f39
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot-rs485-b.dtso
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright 2025 Josua Mayer <josua@solid-run.com>
+ *
+ * Overlay for enabling HummingBoard IIoT on-board RS485 Port B on connector J5004.
+ *
+ * Because Renesas uart driver does not support rs485,
+ * users must manually toggle P41_0 between RX & TX.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&scif3 {
+	pinctrl-0 = <&scif3_pins>, <&scif3_rts_pins>;
+};
+
+&scif3_rs_232_485_mux {
+	/* select rs485 */
+	idle-state = <1>;
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot.dtsi
new file mode 100644
index 0000000000000..22f066079e69a
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-hummingboard-iiot.dtsi
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright 2025 Josua Mayer <josua@solid-run.com>
+ */
+
+#include "rzg2l-hummingboard-iiot-common.dtsi"
+
+&canfd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins>, <&can1_pins>;
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+
+	channel1 {
+		status = "okay";
+	};
+};
+
+&phy1 {
+	leds {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* LED_0 pin */
+		led@0 {
+			reg = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			default-state = "keep";
+		};
+	};
+};
+
+&pinctrl {
+	/* CANA */
+	can0_pins: can0 {
+		pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* CAN0_TX */
+			 <RZG2L_PORT_PINMUX(11, 0, 2)>; /* CAN0_RX */
+	};
+
+	/* CANB */
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* CAN1_TX */
+			 <RZG2L_PORT_PINMUX(13, 0, 2)>; /* CAN1_RX */
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-sr-som-emmc.dtso b/arch/arm64/boot/dts/renesas/rzg2l-sr-som-emmc.dtso
new file mode 100644
index 0000000000000..c59c7e7e70bfa
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-sr-som-emmc.dtso
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+* Device Tree Overlay for the RZ/G2L(C) Solidrun SOM eMMC
+*
+* Copyright (C) 2024 SolidRun Ltd.
+*/
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+&reg_pmic_ldo1 {
+	/*
+	 * This ldo can switch mmc host controller io voltage between
+	 * 1.8V and 3.3V. The eMMC IO voltage however is supplied from
+	 * reg_pmic_buck3 which is fixed at 1.8V.
+	 * Lower this ldo maximum voltage to 1.8V to prevent setting 3.3V.
+	 */
+	regulator-max-microvolt = <1800000>;
+};
+
+&sdhi0 {
+	/*
+	 * Host controller and eMMC have separate io voltage regulators:
+	 * reg_pmic_ldo1 (1.8V/3.3V); reg_pmic_buck3 (1.8V only).
+	 * Link to the switchable regulator ensuring that it gets configured.
+	 */
+	vqmmc-supply = <&reg_pmic_ldo1>;
+	bus-width = <8>;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	mux-states = <&sdhi0_mux 0>;
+	non-removable;
+	no-sdio;
+	pinctrl-0 = <&sdhi0_uhs_pins>, <&sdhi0_rst_pins>;
+	pinctrl-1 = <&sdhi0_uhs_pins>, <&sdhi0_rst_pins>;
+	pinctrl-names = "default", "state_uhs";
+	vmmc-supply = <&reg_pmic_buck4>;
+	/* emmc io voltage is hard-wired for 1.8V, disable sd modes */
+	no-sd;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-sr-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-sr-som.dtsi
new file mode 100644
index 0000000000000..1d52530dcf43c
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-sr-som.dtsi
@@ -0,0 +1,420 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2L Solidrun SoM
+ *
+ * Copyright 2023 SolidRun Ltd.
+ * Copyright 2025 Josua Mayer <josua@solid-run.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+/ {
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+		gpio0 = &pinctrl;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c3;
+		mmc0 = &sdhi0;
+		mmc1 = &sdhi1;
+		rtc0 = &pmic;
+		serial0 = &scif0;
+		serial1 = &scif1;
+		serial2 = &scif2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sdhi0_mux: mux-controller-0 {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		#mux-state-cells = <1>;
+		/*
+		 * Mux switches SD0_DATA[0-3], SD0_CMD & SD0_CLK between
+		 * on-SoM eMMC and board-to-board connector using one gpio:
+		 * 1 = connector, 0 = eMMC.
+		 */
+		mux-gpios = <&pinctrl RZG2L_GPIO(22, 1) GPIO_ACTIVE_LOW>;
+	};
+
+	clk_pmic_32k: pmic-32k-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	reg_pmic_buck1: regulator-pmic-buck1 {
+		compatible = "regulator-fixed";
+		regulator-name = "pmic-buck1";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1100000>;
+		regulator-min-microvolt = <1100000>;
+	};
+
+	reg_pmic_buck3: regulator-pmic-buck3 {
+		compatible = "regulator-fixed";
+		regulator-name = "pmic-buck3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+	};
+
+	reg_pmic_buck4: regulator-pmic-buck4 {
+		compatible = "regulator-fixed";
+		regulator-name = "pmic-buck4";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+	};
+
+	reg_pmic_ldo1: regulator-pmic-ldo1 {
+		compatible = "regulator-gpio";
+		regulator-name = "pmic-ldo1";
+		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <1800000>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	reg_pmic_ldo2: regulator-pmic-ldo2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pmic-ldo2";
+		/*
+		 * This ldo can switch mmc host controller io voltage between
+		 * 1.8V and 3.3V by assembly option of pull-up / pull-dow.
+		 * Default assembly is 3.3V.
+		 */
+		regulator-min-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reserved-memory {
+		ranges;
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		mmp_reserved: linux,multimedia {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x68000000 0x0 0x8000000>;
+			reusable;
+		};
+
+		global_cma: linux,cma@58000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x58000000 0x0 0x10000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	sdhi1_pwrseq: sdhi1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pinctrl RZG2L_GPIO(23, 1) GPIO_ACTIVE_LOW>;
+	};
+
+	/* 32.768kHz crystal */
+	x2: x2-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	memory@40000000 {
+		reg = <0x0 0x40000000 0x0 0x20000000>;
+		device_type = "memory";
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+	pinctrl-0 = <&eth0_pins>;
+	pinctrl-names = "default";
+	/*
+	 * ravb driver does not configure mac internal delays for RZ/G2L(C),
+	 * instead delays are added by the MxL86110 phy driver.
+	 */
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		interrupts-extended = <&pinctrl RZG2L_GPIO(27, 0) IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&eth1 {
+	phy-handle = <&phy1>;
+	pinctrl-0 = <&eth1_pins>;
+	pinctrl-names = "default";
+	/*
+	 * ravb driver does not configure mac internal delays for RZ/G2L(C),
+	 * instead delays are added by the MxL86110 phy driver.
+	 */
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy1: ethernet-phy@4 {
+		reg = <4>;
+		interrupts-extended = <&pinctrl RZG2L_GPIO(42, 4) IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <24000000>;
+};
+
+&gpu {
+	mali-supply = <&reg_pmic_buck1>;
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pmic: pmic@12 {
+		compatible = "renesas,raa215300";
+		reg = <0x12>, <0x6f>;
+		reg-names = "main", "rtc";
+		clocks = <&x2>;
+		clock-names = "xin";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ostm1 {
+	status = "okay";
+};
+
+&ostm2 {
+	status = "okay";
+};
+
+&phyrst {
+	status = "okay";
+};
+
+&pinctrl {
+	eth0_pins: eth0 {
+		pinmux = <RZG2L_PORT_PINMUX(28, 1, 1)>, /* ET0_LINKSTA */
+			 <RZG2L_PORT_PINMUX(27, 1, 1)>, /* ET0_MDC */
+			 <RZG2L_PORT_PINMUX(28, 0, 1)>, /* ET0_MDIO */
+			 <RZG2L_PORT_PINMUX(20, 0, 1)>, /* ET0_TXC */
+			 <RZG2L_PORT_PINMUX(20, 1, 1)>, /* ET0_TX_CTL */
+			 <RZG2L_PORT_PINMUX(20, 2, 1)>, /* ET0_TXD0 */
+			 <RZG2L_PORT_PINMUX(21, 0, 1)>, /* ET0_TXD1 */
+			 <RZG2L_PORT_PINMUX(21, 1, 1)>, /* ET0_TXD2 */
+			 <RZG2L_PORT_PINMUX(22, 0, 1)>, /* ET0_TXD3 */
+			 <RZG2L_PORT_PINMUX(24, 0, 1)>, /* ET0_RXC */
+			 <RZG2L_PORT_PINMUX(24, 1, 1)>, /* ET0_RX_CTL */
+			 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
+			 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
+			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
+			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
+	};
+
+	eth1_pins: eth1 {
+		pinmux = <RZG2L_PORT_PINMUX(37, 2, 1)>, /* ET1_LINKSTA */
+			 <RZG2L_PORT_PINMUX(37, 0, 1)>, /* ET1_MDC */
+			 <RZG2L_PORT_PINMUX(37, 1, 1)>, /* ET1_MDIO */
+			 <RZG2L_PORT_PINMUX(29, 0, 1)>, /* ET1_TXC */
+			 <RZG2L_PORT_PINMUX(29, 1, 1)>, /* ET1_TX_CTL */
+			 <RZG2L_PORT_PINMUX(30, 0, 1)>, /* ET1_TXD0 */
+			 <RZG2L_PORT_PINMUX(30, 1, 1)>, /* ET1_TXD1 */
+			 <RZG2L_PORT_PINMUX(31, 0, 1)>, /* ET1_TXD2 */
+			 <RZG2L_PORT_PINMUX(31, 1, 1)>, /* ET1_TXD3 */
+			 <RZG2L_PORT_PINMUX(33, 1, 1)>, /* ET1_RXC */
+			 <RZG2L_PORT_PINMUX(34, 0, 1)>, /* ET1_RX_CTL */
+			 <RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */
+			 <RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */
+			 <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
+			 <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */
+	};
+
+	i2c0_pins: i2c0 {
+		input-enable;
+		pins = "RIIC0_SDA", "RIIC0_SCL";
+	};
+
+	i2c1_pins: i2c1 {
+		input-enable;
+		pins = "RIIC1_SDA", "RIIC1_SCL";
+	};
+
+	i2c3_pins: i2c3 {
+		pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* RIIC3_SDA */
+			 <RZG2L_PORT_PINMUX(18, 1, 3)>; /* RIIC3_SCL */
+	};
+
+	qspi0_pins: qspi0 {
+		pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3",
+		       "QSPI0_SPCLK", "QSPI0_SSL";
+		power-source = <1800>;
+	};
+
+	scif0_pins: scif0 {
+		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>, /* SCIF0_TXD */
+			 <RZG2L_PORT_PINMUX(38, 1, 1)>; /* SCIF0_RXD */
+	};
+
+	scif2_pins: scif2 {
+		pinmux = <RZG2L_PORT_PINMUX(48, 0, 1)>, /* SCIF2_TXD */
+			 <RZG2L_PORT_PINMUX(48, 1, 1)>, /* SCIF2_RXD */
+			 <RZG2L_PORT_PINMUX(48, 3, 1)>, /* SCIF2_CTS# */
+			 <RZG2L_PORT_PINMUX(48, 4, 1)>; /* SCIF2_RTS# */
+	};
+
+	sdhi0_pins: sdhi0 {
+		pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+		       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7",
+		       "SD0_CLK", "SD0_CMD";
+		power-source = <3300>;
+	};
+
+	sdhi0_uhs_pins: sdhi0 {
+		pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+		       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7",
+		       "SD0_CLK", "SD0_CMD";
+		power-source = <1800>;
+	};
+
+	sdhi0_cd_pins: sdhi0-cd {
+		pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
+	};
+
+	/* SD0_RST is only routed to eMMC which uses fixed 1.8V IO voltage */
+	sdhi0_rst_pins: sdhi0-rst {
+		pins = "SD0_RST#";
+		power-source = <1800>;
+	};
+
+	sdhi1_pins: sdhi1 {
+		pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3",
+		       "SD1_CLK", "SD1_CMD";
+		power-source = <3300>;
+	};
+
+	spi1_pins: spi1 {
+		pinmux = <RZG2L_PORT_PINMUX(44, 2, 1)>, /* RSPI1_MISO */
+			 <RZG2L_PORT_PINMUX(44, 1, 1)>, /* RSPI1_MOSI# */
+			 <RZG2L_PORT_PINMUX(44, 0, 1)>;
+	};
+
+	spi1_cs_pins: spi1-cs {
+		pinmux = <RZG2L_PORT_PINMUX(44, 3, 1)>; /* RSPI1_SSL */
+	};
+
+	usb0_vbus_pins: usb0-vbus {
+		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>; /* USB0_VBUSEN */
+	};
+
+	usb1_vbus_pins: usb1-vbus {
+		pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>; /* USB1_VBUSEN */
+	};
+};
+
+&sbc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "winbond,w25q80bl", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+	};
+};
+
+&scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* WiFi */
+&sdhi1 {
+	/* Murata 1MW max rate is 50MHz */
+	max-frequency = <50000000>;
+	bus-width = <4>;
+	mmc-pwrseq = <&sdhi1_pwrseq>;
+	non-removable;
+	no-1-8-v;
+	no-sd;
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_pmic_buck4>;
+	/*
+	 * Host controller IO voltage is provided from reg_pmic_ldo2,
+	 * WiFi module IO voltage from reg_pmic_buck4.
+	 * Neither is configurable at run-time so either can be set here.
+	 */
+	vqmmc-supply = <&reg_pmic_ldo2>;
+	status = "okay";
+};
+
+&usb2_phy0 {
+	vbus-supply = <&usb0_vbus_otg>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	status = "okay";
+};
+
+&wdt0 {
+	status = "okay";
+};

-- 
2.51.0