From: Leonardo Costa <leoreis.costa@gmail.com>
To: laurent.pinchart@ideasonboard.com, neil.armstrong@linaro.org,
jesszhan0024@gmail.com, maarten.lankhorst@linux.intel.com,
mripard@kernel.org, tzimmermann@suse.de, airlied@gmail.com,
simona@ffwll.ch, robh@kernel.org, krzk+dt@kernel.org,
conor+dt@kernel.org, nm@ti.com, vigneshr@ti.com,
kristo@kernel.org, prabhakar.mahadev-lad.rj@bp.renesas.com,
thierry.reding@gmail.com, sam@ravnborg.org
Cc: leonardo.costa@toradex.com, dri-devel@lists.freedesktop.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/5] arm64: dts: ti: k3-am62-verdin: Add Mezzanine with Toradex Display 10.1" LVDS
Date: Tue, 23 Jun 2026 16:57:41 -0300 [thread overview]
Message-ID: <20260623195741.495734-6-leoreis.costa@gmail.com> (raw)
In-Reply-To: <20260623195741.495734-1-leoreis.costa@gmail.com>
From: Leonardo Costa <leonardo.costa@toradex.com>
Add a device tree overlay enabling the Toradex Capacitive Touch Display
10.1" LVDS V2 on the Verdin Development Board with Verdin AM62 Mezzanine
expansion board. The panel connects via the AM62 OLDI0 on the Mezzanine
LVDS interface (J10). The panel is an Opto Logic SCX1001511GGC49 10.1" WXGA
TFT LCD LVDS and the touch input is provided by an ILITEK ILI251x
capacitive touch controller.
Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
---
arch/arm64/boot/dts/ti/Makefile | 5 +
...zanine-panel-cap-touch-10inch-lvds-v2.dtso | 109 ++++++++++++++++++
2 files changed, 114 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 8b90fef11cb32..d9e0b1b80b28d 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -31,6 +31,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-tqma62xx-mba62xx.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-dev-mezzanine-can.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-dev-nau8822-btl.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-dsi-to-hdmi.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-dsi-to-lvds-panel-cap-touch-10inch.dtbo
@@ -240,6 +241,9 @@ k3-am625-verdin-wifi-dev-mezzanine-can-dtbs := k3-am625-verdin-wifi-dev.dtb \
k3-am625-verdin-wifi-dev-mezzanine-panel-cap-touch-10inch-lvds-dtbs := \
k3-am625-verdin-wifi-dev.dtb \
k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds.dtbo
+k3-am625-verdin-wifi-dev-mezzanine-panel-cap-touch-10inch-lvds-v2-dtbs := \
+ k3-am625-verdin-wifi-dev.dtb \
+ k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtbo
k3-am625-verdin-wifi-dev-nau8822-btl-dtbs := k3-am625-verdin-wifi-dev.dtb \
k3-am625-verdin-dev-nau8822-btl.dtbo
k3-am625-verdin-wifi-dev-ov5640-24mhz-dtbs := k3-am625-verdin-wifi-dev.dtb \
@@ -362,6 +366,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am625-verdin-wifi-dev-dsi-to-lvds-v2-panel-cap-touch-10inch.dtb \
k3-am625-verdin-wifi-dev-mezzanine-can.dtb \
k3-am625-verdin-wifi-dev-mezzanine-panel-cap-touch-10inch-lvds.dtb \
+ k3-am625-verdin-wifi-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtb \
k3-am625-verdin-wifi-dev-nau8822-btl.dtb \
k3-am625-verdin-wifi-dev-ov5640-24mhz.dtb \
k3-am625-verdin-wifi-dev-ov5640.dtb \
diff --git a/arch/arm64/boot/dts/ti/k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtso b/arch/arm64/boot/dts/ti/k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtso
new file mode 100644
index 0000000000000..26f6715463986
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-verdin-dev-mezzanine-panel-cap-touch-10inch-lvds-v2.dtso
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Toradex Capacitive Touch Display 10.1" LVDS V2 on the Verdin AM62 Mezzanine
+ * LVDS interface (J10), used with the Verdin Development Board.
+ *
+ * https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
+ * https://www.toradex.com/accessories/capacitive-touch-display-10.1-inch-lvds
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+&{/} {
+ backlight_pwm2: backlight-pwm2 {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 45 63 88 119 158 203 255>;
+ default-brightness-level = <4>;
+ /* Verdin GPIO_4 (SODIMM 212) - LVDS_BKL_EN */
+ enable-gpios = <&mcu_gpio0 4 GPIO_ACTIVE_HIGH>;
+ /* Verdin PWM_2 (SODIMM 16) - LVDS_PWM */
+ pwms = <&epwm0 1 6666667 0>;
+ };
+
+ panel-lvds-native {
+ compatible = "optologic,scx1001511ggc49", "panel-lvds";
+ backlight = <&backlight_pwm2>;
+ data-mapping = "vesa-24";
+ height-mm = <136>;
+ width-mm = <217>;
+
+ panel-timing {
+ clock-frequency = <64500000>;
+ hactive = <1280>;
+ hback-porch = <20>;
+ hfront-porch = <20>;
+ hsync-len = <2>;
+ vactive = <800>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ vsync-len = <3>;
+ de-active = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pixelclk-active = <0>;
+ };
+
+ port {
+ panel_lvds_native_in: endpoint {
+ remote-endpoint = <&oldi0_out>;
+ };
+ };
+ };
+};
+
+&dss {
+ status = "okay";
+};
+
+&dss_ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* DSS VP1: internal DPI output to OLDIx */
+ port@0 {
+ reg = <0>;
+
+ dss0_out: endpoint {
+ remote-endpoint = <&oldi0_in>;
+ };
+ };
+};
+
+/* Verdin I2C_2_DSI */
+&main_i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ touchscreen@41 {
+ compatible = "ilitek,ili251x";
+ reg = <0x41>;
+ /* Verdin GPIO_3 (SODIMM 210) - LVDS_TOUCH_INT# */
+ interrupt-parent = <&mcu_gpio0>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ /* Verdin GPIO_2 (SODIMM 208) - LVDS_TOUCH_RST# */
+ reset-gpios = <&mcu_gpio0 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&oldi0 {
+ status = "okay";
+};
+
+&oldi0_port0 {
+ oldi0_in: endpoint {
+ remote-endpoint = <&dss0_out>;
+ };
+};
+
+&oldi0_port1 {
+ oldi0_out: endpoint {
+ remote-endpoint = <&panel_lvds_native_in>;
+ };
+};
prev parent reply other threads:[~2026-06-23 19:58 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-06-23 19:57 [PATCH 0/5] arm64: dts: ti: k3-am62-verdin: Add Toradex Capacitive Touch Display 10.1" LVDS Leonardo Costa
2026-06-23 19:57 ` [PATCH 1/5] dt-bindings: vendor-prefixes: Add Opto Logic Leonardo Costa
2026-06-23 19:57 ` [PATCH 2/5] dt-bindings: display: panel-lvds: Add compatible for Opto Logic SCX1001511GGC49 Leonardo Costa
2026-06-23 19:57 ` [PATCH 3/5] arm64: dts: ti: k3-am62-verdin: Add Toradex Capacitive Touch Display 10.1" LVDS V2 Leonardo Costa
2026-06-23 19:57 ` [PATCH 4/5] arm64: dts: ti: k3-am62-verdin: Add Toradex DSI to LVDS adapter with the 10.1" V2 display Leonardo Costa
2026-06-23 19:57 ` Leonardo Costa [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260623195741.495734-6-leoreis.costa@gmail.com \
--to=leoreis.costa@gmail.com \
--cc=airlied@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=jesszhan0024@gmail.com \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=leonardo.costa@toradex.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=nm@ti.com \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=robh@kernel.org \
--cc=sam@ravnborg.org \
--cc=simona@ffwll.ch \
--cc=thierry.reding@gmail.com \
--cc=tzimmermann@suse.de \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox