[PATCH v2 0/4] phy: nuvoton: extend MA35D1 USB2 PHY driver for dual-port OTG support

[Joey Lu <a0987203069@gmail.com>]

The MA35D1 SoC has two USB PHY ports managed by a shared hardware block:

  - PHY0 (USB0): OTG port shared between the DWC2 gadget controller and
    the EHCI0/OHCI0 host controllers.  A hardware mux automatically routes
    USB0 signals to the correct controller based on the USB ID pin.

  - PHY1 (USB1): dedicated host-only port for EHCI1/OHCI1.

A previous series [1] added a separate phy-ma35d1-otg.c driver for this.
Following reviewer suggestion to reuse the existing phy-ma35d1-usb2.c
driver rather than introduce a new one, that series has been dropped and
this series instead extends the existing driver.

Changes in this series:

  Patch 1 (new) adds simple-mfd support to the nuvoton,ma35d1-reset
  syscon binding.  The sys node needs to act as an MFD parent so that
  usb-phy@60 can be its DT child.  This patch is a prerequisite for
  patch 2 and has no functional impact on existing users of the syscon.

  Patch 2 updates the nuvoton,ma35d1-usb2-phy binding: the PHY node
  becomes a child of the syscon node (reg = <0x60 0x14>), nuvoton,sys
  phandle and clocks are removed, and #phy-cells changes from 0 to 1
  for per-port selection.  Optional nuvoton,rcalcode and
  nuvoton,oc-active-high properties are added.

  Patch 3 updates the MA35D1 DTS: sys gains simple-mfd, usb-phy@60 is
  added as a syscon child, and DWC2/EHCI0/EHCI1/OHCI0/OHCI1 nodes are
  added.  Board files enable the nodes and add pinctrl for the HSUSB
  signals (VBUSVLD, PWREN, OVC).

  Patch 4 extends phy-ma35d1-usb2.c: a loop creates two struct phy
  objects; a unified .init handles both ports with parametric register
  macros; clock management is removed (each controller gates its own
  clock); a read-only USB role switch is registered for PHY0 reporting
  the USB ID pin via PWRONOTP[16].

Changes since v1:

  - New patch 1: nuvoton,ma35d1-reset binding extended for simple-mfd
    and child node support; required as a prerequisite for the PHY
    binding which places usb-phy@60 as a syscon child.

  - Patch 2 (was patch 1): nuvoton,rcalcode description updated to
    clarify that both PHY entries are individually optional; example
    reg corrected from 4-cell to 2-cell format.

  - Patch 3 (was patch 2): ehci1 node address corrected to lowercase
    (401c0000).

  - Patch 4 (was patch 3): register definition section header comments
    added; HOST_READY and DEV_READY macro comments made more
    descriptive; ma35_role_switch_exit() added to the PHY provider
    registration error path to prevent a role switch leak.

Link: [1] https://lore.kernel.org/linux-phy/20260604101220.1092822-1-a0987203069@gmail.com/T/#t

Joey Lu (4):
  dt-bindings: reset: nuvoton,ma35d1-reset: add simple-mfd and child
    node support
  dt-bindings: phy: nuvoton,ma35d1-usb2-phy: extend for dual-port OTG
    support
  arm64: dts: nuvoton: ma35d1: add USB controllers and dual-port PHY
    node
  phy: nuvoton: phy-ma35d1-usb2: extend to dual-port with OTG support

 .../bindings/phy/nuvoton,ma35d1-usb2-phy.yaml |  62 +++-
 .../bindings/reset/nuvoton,ma35d1-reset.yaml  |  13 +-
 .../boot/dts/nuvoton/ma35d1-iot-512m.dts      |  36 +++
 .../boot/dts/nuvoton/ma35d1-som-256m.dts      |  36 +++
 arch/arm64/boot/dts/nuvoton/ma35d1.dtsi       |  68 ++++-
 drivers/phy/nuvoton/phy-ma35d1-usb2.c         | 267 +++++++++++++-----
 6 files changed, 391 insertions(+), 91 deletions(-)

-- 
2.43.0