From: Joey Lu <a0987203069@gmail.com>
To: Vinod Koul <vkoul@kernel.org>,
Neil Armstrong <neil.armstrong@linaro.org>
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Arnd Bergmann <arnd@arndb.de>,
Catalin Marinas <catalin.marinas@arm.com>,
Jacky Huang <ychuang3@nuvoton.com>,
Shan-Chun Hung <schung@nuvoton.com>,
Hui-Ping Chen <hpchen0nvt@gmail.com>, Joey Lu <yclu4@nuvoton.com>,
linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Joey Lu <a0987203069@gmail.com>
Subject: [PATCH v4 2/3] arm64: dts: nuvoton: ma35d1: add USB controllers and dual-port PHY node
Date: Mon, 20 Jul 2026 18:22:21 +0800 [thread overview]
Message-ID: <20260720102222.251179-3-a0987203069@gmail.com> (raw)
In-Reply-To: <20260720102222.251179-1-a0987203069@gmail.com>
Add the USB subsystem nodes for the MA35D1 SoC and boards:
- usb_phy: standalone PHY node with #phy-cells = <1>, covering both
the OTG port (PHY0, index 0) and the host-only port (PHY1, index 1).
Uses nuvoton,sys phandle and HUSBH0_GATE clock per the binding.
- usb (DWC2 gadget, USB0): phys = <&usb_phy 0>, dr_mode = peripheral.
- ehci0/ohci0 (USB0 host): phys = <&usb_phy 0>, companion pairing.
- ehci1/ohci1 (USB1 host): phys = <&usb_phy 1>.
Board files (ma35d1-som-256m.dts, ma35d1-iot-512m.dts) add pinctrl for
VBUSVLD, PWREN and OVC signals and enable all USB nodes.
Signed-off-by: Joey Lu <a0987203069@gmail.com>
---
.../boot/dts/nuvoton/ma35d1-iot-512m.dts | 36 ++++++++++
.../boot/dts/nuvoton/ma35d1-som-256m.dts | 36 ++++++++++
arch/arm64/boot/dts/nuvoton/ma35d1.dtsi | 65 +++++++++++++++++++
3 files changed, 137 insertions(+)
diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts b/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts
index 78534d613486..0a068abda6e0 100644
--- a/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts
@@ -97,6 +97,16 @@ pinctrl_uart14: uart14-pins {
power-source = <1>;
};
};
+
+ hsusb {
+ pinctrl_hsusb: hsusb-pins {
+ nuvoton,pins = <5 15 1>, /* VBUSVLD */
+ <11 12 9>, /* PWREN */
+ <11 13 9>; /* OVC */
+ bias-disable;
+ power-source = <1>;
+ };
+ };
};
&uart0 {
@@ -151,3 +161,29 @@ eth_phy1: ethernet-phy@1 {
reg = <1>;
};
};
+
+&usb_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hsusb>;
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts b/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts
index a029b660e8dc..7f1e6d2a1fc2 100644
--- a/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts
@@ -100,6 +100,16 @@ pinctrl_uart16: uart16-pins {
power-source = <1>;
};
};
+
+ hsusb {
+ pinctrl_hsusb: hsusb-pins {
+ nuvoton,pins = <5 15 1>, /* VBUSVLD */
+ <11 12 9>, /* PWREN */
+ <11 13 9>; /* OVC */
+ bias-disable;
+ power-source = <1>;
+ };
+ };
};
&uart0 {
@@ -153,3 +163,29 @@ eth_phy1: ethernet-phy@1 {
reg = <1>;
};
};
+
+&usb_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hsusb>;
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi b/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
index 7228ad4735b5..5a7a39b1b514 100644
--- a/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
@@ -88,6 +88,14 @@ sys: system-management@40460000 {
#reset-cells = <1>;
};
+ usb_phy: usb-phy {
+ compatible = "nuvoton,ma35d1-usb2-phy";
+ clocks = <&clk HUSBH0_GATE>;
+ nuvoton,sys = <&sys>;
+ #phy-cells = <1>;
+ status = "disabled";
+ };
+
clk: clock-controller@40460200 {
compatible = "nuvoton,ma35d1-clk";
reg = <0x00000000 0x40460200 0x0 0x100>;
@@ -431,5 +439,62 @@ mdio1: mdio {
#size-cells = <0>;
};
};
+
+ usb: usb@40200000 {
+ compatible = "snps,dwc2";
+ reg = <0x0 0x40200000 0x0 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk USBD_GATE>;
+ clock-names = "otg";
+ phys = <&usb_phy 0>;
+ phy-names = "usb2-phy";
+ dr_mode = "peripheral";
+ g-np-tx-fifo-size = <16>;
+ g-rx-fifo-size = <0x100>;
+ g-tx-fifo-size = <256 256 64 64 64 32 32 32>;
+ status = "disabled";
+ };
+
+ ehci0: usb@40140000 {
+ compatible = "generic-ehci";
+ reg = <0x0 0x40140000 0x0 0x1000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk HUSBH0_GATE>;
+ phys = <&usb_phy 0>;
+ phy-names = "usb";
+ companion = <&ohci0>;
+ status = "disabled";
+ };
+
+ ehci1: usb@401c0000 {
+ compatible = "generic-ehci";
+ reg = <0x0 0x401c0000 0x0 0x1000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk HUSBH1_GATE>;
+ phys = <&usb_phy 1>;
+ phy-names = "usb";
+ companion = <&ohci1>;
+ status = "disabled";
+ };
+
+ ohci0: usb@40150000 {
+ compatible = "generic-ohci";
+ reg = <0x0 0x40150000 0x0 0x1000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk HUSBH0_GATE>;
+ phys = <&usb_phy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@401d0000 {
+ compatible = "generic-ohci";
+ reg = <0x0 0x401d0000 0x0 0x1000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk HUSBH1_GATE>;
+ phys = <&usb_phy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
};
};
--
2.43.0
next prev parent reply other threads:[~2026-07-20 10:22 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-20 10:22 [PATCH v4 0/3] phy: nuvoton: extend MA35D1 USB2 PHY driver for dual-port OTG support Joey Lu
2026-07-20 10:22 ` [PATCH v4 1/3] dt-bindings: phy: nuvoton,ma35d1-usb2-phy: extend for dual-port and OTG Joey Lu
2026-07-20 10:28 ` sashiko-bot
2026-07-20 10:22 ` Joey Lu [this message]
2026-07-20 10:32 ` [PATCH v4 2/3] arm64: dts: nuvoton: ma35d1: add USB controllers and dual-port PHY node sashiko-bot
2026-07-20 10:22 ` [PATCH v4 3/3] phy: nuvoton: phy-ma35d1-usb2: extend to dual-port with OTG support Joey Lu
2026-07-20 10:37 ` sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260720102222.251179-3-a0987203069@gmail.com \
--to=a0987203069@gmail.com \
--cc=arnd@arndb.de \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=hpchen0nvt@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=neil.armstrong@linaro.org \
--cc=robh@kernel.org \
--cc=schung@nuvoton.com \
--cc=vkoul@kernel.org \
--cc=ychuang3@nuvoton.com \
--cc=yclu4@nuvoton.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox