Devicetree
 help / color / mirror / Atom feed
From: Stoyan Bogdanov <sbogdanov@baylibre.com>
To: jbrunet@baylibre.com, linux@roeck-us.net, robh@kernel.org,
	krzk+dt@kernel.org, conor+dt@kernel.org, corbet@lwn.net,
	skhan@linuxfoundation.org
Cc: linux-hwmon@vger.kernel.org, devicetree@vger.kernel.org,
	linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org,
	Stoyan Bogdanov <sbogdanov@baylibre.com>
Subject: [PATCH v6 3/3] hwmon: (pmbus/tps25990): Add TPS1689 support
Date: Wed,  5 Aug 2026 12:03:57 +0300	[thread overview]
Message-ID: <20260805090400.2059006-4-sbogdanov@baylibre.com> (raw)
In-Reply-To: <20260805090400.2059006-1-sbogdanov@baylibre.com>

Extend the existing TPS25990 driver to support the TPS1689 eFuse,
as both devices share the same command interface and functionality.

Update the documentation to include TPS1689 support.

Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
---
 Documentation/hwmon/tps25990.rst |  15 +++--
 drivers/hwmon/pmbus/tps25990.c   | 106 ++++++++++++++++++++++++++++---
 2 files changed, 107 insertions(+), 14 deletions(-)

diff --git a/Documentation/hwmon/tps25990.rst b/Documentation/hwmon/tps25990.rst
index 04faec780d26..e8bc9a550bda 100644
--- a/Documentation/hwmon/tps25990.rst
+++ b/Documentation/hwmon/tps25990.rst
@@ -9,26 +9,31 @@ Supported chips:
 
     Prefix: 'tps25990'
 
-  * Datasheet
+    Datasheet: Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps25990
 
-    Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps25990
+  * TI TPS1689
+
+    Prefix: 'tps1689'
+
+    Datasheet: Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps1689
 
 Author:
 
 	Jerome Brunet <jbrunet@baylibre.com>
+	Stoyan Bogdanov <sbogdanov@baylibre.com>
 
 Description
 -----------
 
-This driver implements support for TI TPS25990 eFuse.
+This driver implements support for TI TPS25990 and TI TPS1689 eFuse chips.
 This is an integrated, high-current circuit protection and power
 management device with PMBUS interface
 
-Device compliant with:
+Devices are compliant with:
 
 - PMBus rev 1.3 interface.
 
-Device supports direct format for reading input voltages,
+Devices supports direct format for reading input voltages,
 output voltage, input current, input power and temperature.
 
 Due to the specificities of the chip, all history reset attributes
diff --git a/drivers/hwmon/pmbus/tps25990.c b/drivers/hwmon/pmbus/tps25990.c
index 7634ac743025..a91ea8f33b29 100644
--- a/drivers/hwmon/pmbus/tps25990.c
+++ b/drivers/hwmon/pmbus/tps25990.c
@@ -47,7 +47,14 @@
 					 PK_MIN_AVG_RST_AVG  | \
 					 PK_MIN_AVG_RST_MIN)
 
+#define TPS1689_VIN_OV_RANGE_SEL_MASK	GENMASK(7, 6)
+#define TPS1689_VIN_VOV_MASK		GENMASK(5, 0)
+#define TPS1689_VIN_SCALING		251
+#define TPS1689_VIN_VOV_STEP_MV		250
+#define TPS1689_VIN_RANGE_SPAN_MV	16000
+
 enum chips {
+	tps1689,
 	tps25990,
 };
 
@@ -105,6 +112,8 @@ static int tps25990_mfr_write_protect_get(struct i2c_client *client)
 static int tps25990_read_word_data(struct i2c_client *client,
 				   int page, int phase, int reg)
 {
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tps25990_data *data = container_of(info, struct tps25990_data, info);
 	int ret;
 
 	switch (reg) {
@@ -193,9 +202,18 @@ static int tps25990_read_word_data(struct i2c_client *client,
 		ret = pmbus_read_word_data(client, page, phase, reg);
 		if (ret < 0)
 			break;
-		ret = DIV_ROUND_CLOSEST(ret * TPS25990_VIN_OVF_NUM,
-					TPS25990_VIN_OVF_DIV);
-		ret += TPS25990_VIN_OVF_OFF;
+		if (data->chip_id == tps25990) {
+			ret = DIV_ROUND_CLOSEST(ret * TPS25990_VIN_OVF_NUM,
+						TPS25990_VIN_OVF_DIV);
+			ret += TPS25990_VIN_OVF_OFF;
+		} else if (data->chip_id == tps1689) {
+			ret = DIV_ROUND_CLOSEST(
+				((FIELD_GET(TPS1689_VIN_OV_RANGE_SEL_MASK, ret) + 1) *
+				TPS1689_VIN_RANGE_SPAN_MV) +
+				(FIELD_GET(TPS1689_VIN_VOV_MASK, ret) *
+				TPS1689_VIN_VOV_STEP_MV - TPS1689_VIN_RANGE_SPAN_MV),
+				TPS1689_VIN_SCALING);
+		}
 		break;
 
 	case PMBUS_IIN_OC_FAULT_LIMIT:
@@ -208,7 +226,7 @@ static int tps25990_read_word_data(struct i2c_client *client,
 		if (ret < 0)
 			break;
 		ret = DIV_ROUND_CLOSEST(ret * TPS25990_IIN_OCF_NUM,
-					TPS25990_IIN_OCF_DIV);
+						TPS25990_IIN_OCF_DIV);
 		ret += TPS25990_IIN_OCF_OFF;
 		break;
 
@@ -238,6 +256,8 @@ static int tps25990_read_word_data(struct i2c_client *client,
 static int tps25990_write_word_data(struct i2c_client *client,
 				    int page, int reg, u16 value)
 {
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tps25990_data *data = container_of(info, struct tps25990_data, info);
 	int ret;
 
 	switch (reg) {
@@ -255,10 +275,23 @@ static int tps25990_write_word_data(struct i2c_client *client,
 		break;
 
 	case PMBUS_VIN_OV_FAULT_LIMIT:
-		value -= TPS25990_VIN_OVF_OFF;
-		value = DIV_ROUND_CLOSEST(((unsigned int)value) * TPS25990_VIN_OVF_DIV,
-					  TPS25990_VIN_OVF_NUM);
-		value = clamp_val(value, 0, 0xf);
+		if (data->chip_id == tps25990) {
+			value -= TPS25990_VIN_OVF_OFF;
+			value = DIV_ROUND_CLOSEST(((unsigned int)value) * TPS25990_VIN_OVF_DIV,
+						  TPS25990_VIN_OVF_NUM);
+			value = clamp_val(value, 0, 0xf);
+		} else if (data->chip_id == tps1689) {
+			u32 scaled_value = value * TPS1689_VIN_SCALING + TPS1689_VIN_RANGE_SPAN_MV;
+			u32 tmp_scaled_value = scaled_value;
+			u8 ov_rng_sel = 0;
+			u32 ov_set = 0;
+
+			ov_rng_sel = tmp_scaled_value / TPS1689_VIN_RANGE_SPAN_MV;
+			ov_set = tmp_scaled_value - (TPS1689_VIN_RANGE_SPAN_MV * ov_rng_sel);
+			value = FIELD_PREP(TPS1689_VIN_OV_RANGE_SEL_MASK, ov_rng_sel - 1) |
+						FIELD_PREP(TPS1689_VIN_VOV_MASK,
+						(ov_set / TPS1689_VIN_VOV_STEP_MV));
+		}
 		ret = pmbus_write_word_data(client, page, reg, value);
 		break;
 
@@ -347,6 +380,60 @@ static const struct regulator_desc tps25990_reg_desc[] = {
 #endif
 
 static const struct pmbus_driver_info tps25990_base_info[] = {
+	[tps1689] = {
+		.pages = 1,
+		.format[PSC_VOLTAGE_IN] = direct,
+		.m[PSC_VOLTAGE_IN] = 3984,
+		.b[PSC_VOLTAGE_IN] = -63750,
+		.R[PSC_VOLTAGE_IN] = -3,
+		.format[PSC_VOLTAGE_OUT] = direct,
+		.m[PSC_VOLTAGE_OUT] = 1166,
+		.b[PSC_VOLTAGE_OUT] = 0,
+		.R[PSC_VOLTAGE_OUT] = -2,
+		.format[PSC_TEMPERATURE] = direct,
+		.m[PSC_TEMPERATURE] = 140,
+		.b[PSC_TEMPERATURE] = 32103,
+		.R[PSC_TEMPERATURE] = -2,
+		/*
+		 * Current and Power measurement depends on the ohm value
+		 * of Rimon. m is multiplied by 1000 below to have an integer
+		 * and -3 is added to R to compensate.
+		 */
+		.format[PSC_CURRENT_IN] = direct,
+		.m[PSC_CURRENT_IN] = 9548,
+		.b[PSC_CURRENT_IN] = 0,
+		.R[PSC_CURRENT_IN] = -6,
+		.format[PSC_CURRENT_OUT] = direct,
+		.m[PSC_CURRENT_OUT] = 24347,
+		.b[PSC_CURRENT_OUT] = 0,
+		.R[PSC_CURRENT_OUT] = -3,
+		.format[PSC_POWER] = direct,
+		.m[PSC_POWER] = 2775,
+		.b[PSC_POWER] = 0,
+		.R[PSC_POWER] = -4,
+		.func[0] = (PMBUS_HAVE_VIN |
+			    PMBUS_HAVE_VOUT |
+			    PMBUS_HAVE_VMON |
+			    PMBUS_HAVE_IIN |
+			    PMBUS_HAVE_IOUT |
+			    PMBUS_HAVE_PIN |
+			    PMBUS_HAVE_TEMP |
+			    PMBUS_HAVE_STATUS_VOUT |
+			    PMBUS_HAVE_STATUS_IOUT |
+			    PMBUS_HAVE_STATUS_INPUT |
+			    PMBUS_HAVE_STATUS_TEMP |
+			    PMBUS_HAVE_SAMPLES),
+
+		.read_word_data = tps25990_read_word_data,
+		.write_word_data = tps25990_write_word_data,
+		.read_byte_data = tps25990_read_byte_data,
+		.write_byte_data = tps25990_write_byte_data,
+
+#if IS_ENABLED(CONFIG_SENSORS_TPS25990_REGULATOR)
+		.reg_desc = tps25990_reg_desc,
+		.num_regulators = ARRAY_SIZE(tps25990_reg_desc),
+#endif
+		},
 	[tps25990] = {
 		.pages = 1,
 		.format[PSC_VOLTAGE_IN] = direct,
@@ -389,7 +476,6 @@ static const struct pmbus_driver_info tps25990_base_info[] = {
 		.write_word_data = tps25990_write_word_data,
 		.read_byte_data = tps25990_read_byte_data,
 		.write_byte_data = tps25990_write_byte_data,
-
 #if IS_ENABLED(CONFIG_SENSORS_TPS25990_REGULATOR)
 		.reg_desc = tps25990_reg_desc,
 		.num_regulators = ARRAY_SIZE(tps25990_reg_desc),
@@ -398,12 +484,14 @@ static const struct pmbus_driver_info tps25990_base_info[] = {
 };
 
 static const struct i2c_device_id tps25990_i2c_id[] = {
+	{ .name = "tps1689", .driver_data = tps1689 },
 	{ .name = "tps25990", .driver_data = tps25990 },
 	{}
 };
 MODULE_DEVICE_TABLE(i2c, tps25990_i2c_id);
 
 static const struct of_device_id tps25990_of_match[] = {
+	{ .compatible = "ti,tps1689", .data = (void *)tps1689 },
 	{ .compatible = "ti,tps25990", .data = (void *)tps25990 },
 	{}
 };
-- 
2.43.0


  parent reply	other threads:[~2026-08-05  9:04 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-08-05  9:03 [PATCH v6 0/3] Rework TPS25990 direct conversions and add TPS1689 support Stoyan Bogdanov
2026-08-05  9:03 ` [PATCH v6 1/3] hwmon: (pmbus/tps25990): Rework driver for multi-device support Stoyan Bogdanov
2026-08-05  9:09   ` sashiko-bot
2026-08-05  9:03 ` [PATCH v6 2/3] dt-bindings: hwmon: pmbus/tps25990: Add TPS1689 Stoyan Bogdanov
2026-08-05  9:07   ` sashiko-bot
2026-08-05  9:03 ` Stoyan Bogdanov [this message]
2026-08-05  9:20   ` [PATCH v6 3/3] hwmon: (pmbus/tps25990): Add TPS1689 support sashiko-bot
2026-08-05 15:28     ` Guenter Roeck

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260805090400.2059006-4-sbogdanov@baylibre.com \
    --to=sbogdanov@baylibre.com \
    --cc=conor+dt@kernel.org \
    --cc=corbet@lwn.net \
    --cc=devicetree@vger.kernel.org \
    --cc=jbrunet@baylibre.com \
    --cc=krzk+dt@kernel.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-hwmon@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@roeck-us.net \
    --cc=robh@kernel.org \
    --cc=skhan@linuxfoundation.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox