[PATCH v5 1/2] dt-bindings: iio: proximity: move LIDAR-Lite v2 out of trivial-devices

[Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>]

The PulsedLight LIDAR-Lite v2 is currently described as a trivial device,
but it is not one: besides the I2C interface it exposes a power-enable
pin and a mode-control pin.

The mode-control pin can trigger acquisitions and report the measured
distance through a PWM signal, entirely bypassing I2C. That usage is
bidirectional and non-cyclic, so it doesn't map onto any existing
binding for describing pin behaviour, and is intentionally left
undocumented here. The same pin can, however, also be used as a plain
status output while I2C remains the active interface, which is
described through the new interrupts property.

Move the device to a dedicated binding file and document the
power-enable, power-supply and interrupt properties that
trivial-devices.yaml has no way to express.

Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
---
 .../proximity/pulsedlight,lidar-lite-v2.yaml  | 64 +++++++++++++++++++
 .../devicetree/bindings/trivial-devices.yaml  |  2 -
 2 files changed, 64 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/iio/proximity/pulsedlight,lidar-lite-v2.yaml

diff --git a/Documentation/devicetree/bindings/iio/proximity/pulsedlight,lidar-lite-v2.yaml b/Documentation/devicetree/bindings/iio/proximity/pulsedlight,lidar-lite-v2.yaml
new file mode 100644
index 000000000000..e19c8d166b81
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/pulsedlight,lidar-lite-v2.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/pulsedlight,lidar-lite-v2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Pulsedlight LIDAR-Lite v2 range-finding sensor
+
+maintainers:
+  - Matt Ranostay <mranostay@gmail.com>
+
+description: |
+  This binding covers the I2C interface of the Pulsedlight LIDAR-Lite v2
+  laser rangefinder.
+
+  Besides I2C, the mode control pin can also trigger acquisitions and
+  report the measured distance through a PWM signal, without using I2C
+  at all. That usage is bidirectional and non-cyclic, and is not
+  described by this binding. The same pin can also be used, while I2C
+  remains the active interface, as a plain status output signalling
+  when an acquisition has completed.
+
+  Datasheet:
+    https://github.com/PulsedLight3D/LIDAR-Lite-Documentation/blob/master/Docs/LIDAR-Lite-v2-Docs.pdf
+
+properties:
+  compatible:
+    const: pulsedlight,lidar-lite-v2
+
+  reg:
+    maxItems: 1
+
+  powerdown-gpios:
+    description: GPIO that can be driven low to shut off power to the device.
+    maxItems: 1
+
+  vdd-supply: true
+
+  interrupts:
+    description:
+      Mode control pin used as a status output, driven while the device is
+      busy performing an acquisition. Can be used to signal completion
+      instead of polling over I2C.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - vdd-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        lidar@62 {
+            compatible = "pulsedlight,lidar-lite-v2";
+            reg = <0x62>;
+            vdd-supply = <&vdd_5v0>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
index 435c4baab436..74b640c48598 100644
--- a/Documentation/devicetree/bindings/trivial-devices.yaml
+++ b/Documentation/devicetree/bindings/trivial-devices.yaml
@@ -396,8 +396,6 @@ properties:
           - onnn,adt7462
             # 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
           - plx,pex8648
-            # Pulsedlight LIDAR range-finding sensor
-          - pulsedlight,lidar-lite-v2
             # Renesas HS3001 Temperature and Relative Humidity Sensors
           - renesas,hs3001
             # Renesas ISL29501 time-of-flight sensor
-- 
2.48.1