From: Janani Sunil <janani.sunil@analog.com>
To: "Nuno Sá" <nuno.sa@analog.com>,
"Michael Hennerich" <Michael.Hennerich@analog.com>,
"Jonathan Cameron" <jic23@kernel.org>,
"David Lechner" <dlechner@baylibre.com>,
"Andy Shevchenko" <andy@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Olivier Moysan" <olivier.moysan@foss.st.com>,
"Philipp Zabel" <p.zabel@pengutronix.de>,
"Linus Walleij" <linusw@kernel.org>,
"Bartosz Golaszewski" <brgl@kernel.org>,
"Jonathan Corbet" <corbet@lwn.net>,
"Shuah Khan" <skhan@linuxfoundation.org>,
"Michael Walle" <mwalle@kernel.org>
Cc: linux@analog.com, linux-iio@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-gpio@vger.kernel.org, linux-doc@vger.kernel.org,
jananisunil.dev@gmail.com,
"Uwe Kleine-König" <u.kleine-koenig@baylibre.com>,
"Janani Sunil" <janani.sunil@analog.com>
Subject: [PATCH v5 14/20] iio: adc: ad7768: Add per-channel conversion delay
Date: Fri, 28 Aug 2026 17:30:37 +0200 [thread overview]
Message-ID: <20260828-ad7768-driver-v5-14-e33ca6f841a2@analog.com> (raw)
In-Reply-To: <20260828-ad7768-driver-v5-0-e33ca6f841a2@analog.com>
Expose the per-channel synchronization phase offset through the IIO
conversion-delay attribute.
Derive the delay resolution from MCLK, power mode and decimation rate.
Validate the requested delay and program the corresponding phase
register when applying the active channel configuration.
Signed-off-by: Janani Sunil <janani.sunil@analog.com>
---
drivers/iio/adc/ad7768.c | 129 +++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 129 insertions(+)
diff --git a/drivers/iio/adc/ad7768.c b/drivers/iio/adc/ad7768.c
index f2f318ebf964..4133e3a033b4 100644
--- a/drivers/iio/adc/ad7768.c
+++ b/drivers/iio/adc/ad7768.c
@@ -154,6 +154,12 @@ struct ad7768_freq_config {
unsigned int dec_rate;
};
+struct ad7768_convdelay_params {
+ unsigned int shift;
+ unsigned int max_raw;
+ u64 step_ps;
+};
+
struct ad7768_avail_freq {
unsigned int n_freqs;
struct ad7768_freq_config freq_cfg[AD7768_MAX_FREQ_PER_MODE];
@@ -182,6 +188,7 @@ struct ad7768_state {
unsigned int n_freqs;
int freqs[AD7768_MAX_FREQS];
unsigned int ch_freq[AD7768_MAX_CHANNEL];
+ u64 ch_convdelay_ps[AD7768_MAX_CHANNEL];
enum ad7768_filter_type ch_filter[AD7768_MAX_CHANNEL];
struct iio_backend *back;
unsigned int vref_uV[2];
@@ -251,6 +258,12 @@ static unsigned int ad7768_gain_reg(const struct ad7768_state *st,
return AD7768_REG_GAIN(st->chip_info->chan_map[ch]);
}
+static unsigned int ad7768_phase_reg(const struct ad7768_state *st,
+ unsigned int ch)
+{
+ return AD7768_REG_PHASE(st->chip_info->chan_map[ch]);
+}
+
static u8 ad7768_precharge_buf1_mask(const struct ad7768_state *st, u16 val)
{
return val & GENMASK(st->chip_info->prebuf_split - 1, 0);
@@ -661,6 +674,92 @@ static int ad7768_find_matching_mode(const bool *mode_used,
return -EINVAL;
}
+static int ad7768_get_convdelay_params(struct ad7768_state *st, unsigned int ch,
+ struct ad7768_convdelay_params *params)
+{
+ const struct ad7768_freq_config *freq_cfg;
+ unsigned int dec_rate;
+ unsigned int mclk_div;
+ unsigned int mult;
+ u64 mclk;
+
+ freq_cfg = ad7768_find_freq_config(st, st->power_mode_idx,
+ st->ch_freq[ch]);
+ if (!freq_cfg)
+ return -EINVAL;
+
+ dec_rate = ad7768_dec_rate[freq_cfg->dec_rate];
+ switch (dec_rate) {
+ case 32:
+ params->shift = 3;
+ params->max_raw = 31;
+ mult = 1;
+ break;
+ case 64:
+ params->shift = 2;
+ params->max_raw = 63;
+ mult = 1;
+ break;
+ case 128:
+ params->shift = 1;
+ params->max_raw = 127;
+ mult = 1;
+ break;
+ case 256:
+ params->shift = 0;
+ params->max_raw = 255;
+ mult = 1;
+ break;
+ case 512:
+ params->shift = 0;
+ params->max_raw = 255;
+ mult = 2;
+ break;
+ case 1024:
+ params->shift = 0;
+ params->max_raw = 255;
+ mult = 4;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mclk = clk_get_rate(st->mclk);
+ if (!mclk)
+ return -EINVAL;
+
+ mclk_div = ad7768_power_modes[st->power_mode_idx].mclk_div;
+ params->step_ps = DIV_ROUND_CLOSEST_ULL((u64)mult * PSEC_PER_SEC *
+ mclk_div, mclk);
+
+ return 0;
+}
+
+static int ad7768_set_channel_convdelay(struct ad7768_state *st,
+ unsigned int ch)
+{
+ u64 delay_ps = st->ch_convdelay_ps[ch];
+ struct ad7768_convdelay_params params;
+ u64 max_delay_ps;
+ u64 raw;
+ int ret;
+
+ ret = ad7768_get_convdelay_params(st, ch, ¶ms);
+ if (ret)
+ return ret;
+
+ max_delay_ps = (u64)params.max_raw * params.step_ps;
+ if (delay_ps > max_delay_ps)
+ return -EINVAL;
+
+ raw = DIV_ROUND_CLOSEST_ULL(delay_ps, params.step_ps);
+ if (raw > params.max_raw)
+ return -EINVAL;
+
+ return regmap_write(st->regmap, ad7768_phase_reg(st, ch),
+ raw << params.shift);
+}
+
static void ad7768_filter_wait(const unsigned int *mode_freq,
const enum ad7768_filter_type *mode_filter,
const bool *mode_used)
@@ -766,6 +865,16 @@ static int ad7768_apply_channel_modes(struct iio_dev *indio_dev,
max_freq = max(max_freq, mode_freq[mode]);
}
+ for_each_set_bit(c, scan_mask, st->chip_info->num_channels) {
+ ret = ad7768_set_channel_convdelay(st, c);
+ if (ret == -EINVAL)
+ return dev_err_probe(regmap_get_device(st->regmap), ret,
+ "Invalid conversion delay for channel %u\n",
+ c);
+ if (ret)
+ return ret;
+ }
+
ret = ad7768_set_clk_divs(st, max_freq);
if (ret)
return ret;
@@ -880,6 +989,13 @@ static int ad7768_read_raw(struct iio_dev *indio_dev,
*val = calib;
return IIO_VAL_INT;
}
+ case IIO_CHAN_INFO_CONVDELAY: {
+ guard(mutex)(&st->lock);
+ iio_val_s64_decompose(st->ch_convdelay_ps[chan->channel],
+ val, val2);
+
+ return IIO_VAL_DECIMAL64_PICO;
+ }
default:
return -EINVAL;
}
@@ -893,6 +1009,8 @@ static int ad7768_write_raw_get_fmt(struct iio_dev *indio_dev,
case IIO_CHAN_INFO_CALIBBIAS:
case IIO_CHAN_INFO_CALIBSCALE:
return IIO_VAL_INT;
+ case IIO_CHAN_INFO_CONVDELAY:
+ return IIO_VAL_DECIMAL64_PICO;
default:
return -EINVAL;
}
@@ -904,6 +1022,7 @@ static int ad7768_write_raw(struct iio_dev *indio_dev,
{
struct ad7768_state *st = iio_priv(indio_dev);
unsigned int base_reg;
+ s64 delay_ps;
IIO_DEV_ACQUIRE_DIRECT_MODE(indio_dev, claim);
if (IIO_DEV_ACQUIRE_FAILED(claim))
@@ -924,6 +1043,15 @@ static int ad7768_write_raw(struct iio_dev *indio_dev,
base_reg = ad7768_get_calib_reg_base(st, chan, true);
return ad7768_write_calib_value(st, base_reg, val);
+ case IIO_CHAN_INFO_CONVDELAY: {
+ delay_ps = iio_val_s64_compose(val, val2);
+ if (delay_ps < 0)
+ return -EINVAL;
+
+ guard(mutex)(&st->lock);
+ st->ch_convdelay_ps[chan->channel] = delay_ps;
+ return 0;
+ }
default:
return -EINVAL;
}
@@ -1141,6 +1269,7 @@ static int ad7768_parse_config(struct iio_dev *indio_dev,
.type = IIO_VOLTAGE,
.info_mask_separate = BIT(IIO_CHAN_INFO_CALIBBIAS) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
+ BIT(IIO_CHAN_INFO_CONVDELAY) |
BIT(IIO_CHAN_INFO_SCALE) |
BIT(IIO_CHAN_INFO_SAMP_FREQ),
.info_mask_separate_available =
--
2.43.0
next prev parent reply other threads:[~2026-08-28 15:31 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-08-28 15:30 [PATCH v5 00/20] iio: adc: Add AD7768/AD7768-4 ADC driver support Janani Sunil
2026-08-28 15:30 ` [PATCH v5 01/20] iio: adc: adi-axi-adc: Initialize state mutex Janani Sunil
2026-08-28 15:30 ` [PATCH v5 02/20] dt-bindings: iio: adc: Add AD7768 Janani Sunil
2026-08-28 15:30 ` [PATCH v5 03/20] iio: backend: Add support for CRC Janani Sunil
2026-08-28 15:30 ` [PATCH v5 04/20] iio: adc: adi-axi-adc: " Janani Sunil
2026-08-28 15:30 ` [PATCH v5 05/20] iio: adc: Add AD7768 and AD7768-4 core support Janani Sunil
2026-08-28 15:30 ` [PATCH v5 06/20] iio: adc: ad7768: Validate master clock rate Janani Sunil
2026-08-28 15:30 ` [PATCH v5 07/20] iio: adc: ad7768: Add power mode helper Janani Sunil
2026-08-28 15:30 ` [PATCH v5 08/20] iio: adc: ad7768: Derive output data rates Janani Sunil
2026-08-28 15:30 ` [PATCH v5 09/20] iio: adc: ad7768: Configure channel sampling profiles Janani Sunil
2026-08-28 15:30 ` [PATCH v5 10/20] iio: adc: ad7768: Add sampling frequency controls Janani Sunil
2026-08-28 15:30 ` [PATCH v5 11/20] iio: adc: ad7768: Add per-channel filter controls Janani Sunil
2026-08-28 15:30 ` [PATCH v5 12/20] iio: adc: ad7768: Wait for digital filters to settle Janani Sunil
2026-08-28 15:30 ` [PATCH v5 13/20] iio: adc: ad7768: Add calibration controls Janani Sunil
2026-08-28 15:30 ` Janani Sunil [this message]
2026-08-28 15:30 ` [PATCH v5 15/20] iio: adc: ad7768: Add VCM regulator support Janani Sunil
2026-08-28 15:30 ` [PATCH v5 16/20] iio: adc: ad7768: Register GPIO auxiliary device Janani Sunil
2026-08-28 15:30 ` [PATCH v5 17/20] gpio: regmap: Use regmap_test_bits() for single bit reads Janani Sunil
2026-08-28 15:30 ` [PATCH v5 18/20] gpio: regmap: Add optional runtime PM support Janani Sunil
2026-08-28 15:30 ` [PATCH v5 19/20] gpio: ad7768: Add AD7768 GPIO auxiliary driver Janani Sunil
2026-08-28 15:30 ` [PATCH v5 20/20] Documentation: iio: Add AD7768 Documentation Janani Sunil
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260828-ad7768-driver-v5-14-e33ca6f841a2@analog.com \
--to=janani.sunil@analog.com \
--cc=Michael.Hennerich@analog.com \
--cc=andy@kernel.org \
--cc=brgl@kernel.org \
--cc=conor+dt@kernel.org \
--cc=corbet@lwn.net \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=jananisunil.dev@gmail.com \
--cc=jic23@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linusw@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@analog.com \
--cc=mwalle@kernel.org \
--cc=nuno.sa@analog.com \
--cc=olivier.moysan@foss.st.com \
--cc=p.zabel@pengutronix.de \
--cc=robh@kernel.org \
--cc=skhan@linuxfoundation.org \
--cc=u.kleine-koenig@baylibre.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox