On Sat, Aug 29, 2026 at 01:59:21PM +0800, Kim Seer Paller wrote:
> Add device tree bindings for the Analog Devices AD5710R/AD5711R
> 8-channel 12-/16-bit Configurable IDAC/VDAC.
> 
> Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
> ---
>  .../devicetree/bindings/iio/dac/adi,ad5710r.yaml   | 143 +++++++++++++++++++++
>  MAINTAINERS                                        |   1 +
>  2 files changed, 144 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad5710r.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad5710r.yaml
> new file mode 100644
> index 000000000000..259866ca87cf
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad5710r.yaml
> @@ -0,0 +1,143 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/dac/adi,ad5710r.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices AD5710R/AD5711R 8-channel 12-/16-bit Configurable IDAC/VDAC
> +
> +maintainers:
> +  - Kim Seer Paller <kimseer.paller@analog.com>
> +
> +description: |
> +  The AD5710R (16-bit) and AD5711R (12-bit) are 8-channel, low-power,
> +  configurable current/voltage output digital-to-analog converters (DACs) with
> +  an on-chip 2.5V, 3ppm/°C reference. Each channel can be independently
> +  configured as a voltage output (0V to VREF or 0V to 2 x VREF) or a current
> +  output (0mA to 50mA). These devices operate from a single 2.7V to 5.5V
> +  supply and are guaranteed monotonic by design.
> +
> +  Datasheet can be found here:
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ad5711r-ad5710r.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,ad5710r
> +      - adi,ad5711r
> +
> +  reg:
> +    maxItems: 1
> +
> +  spi-max-frequency:
> +    maximum: 20000000
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 0
> +
> +  vdd-supply:
> +    description: Power Supply Input.
> +
> +  iovdd-supply:
> +    description: Digital Power Supply Input.
> +
> +  io-channels:
> +    description:
> +      ADC channel used to monitor internal die temperature, output voltages, and
> +      current of a selected channel via the MUXOUT pin.
> +    maxItems: 1
> +
> +  ref-supply:
> +    description:
> +      Reference Input/Output. The voltage at the REF pin sets the full-scale
> +      range of all channels. If not provided the internal reference is used and
> +      also provided on the VREF pin.
> +
> +  reset-gpios:
> +    description:
> +      Active low signal that is falling edge sensitive. When it is deasserted,
> +      the digital core initialization is performed and all DAC registers except
> +      the Interface Configuration A register are reset to their default values.
> +    maxItems: 1
> +
> +  ldac-gpios:
> +    description:
> +      LDAC pin to be used as a hardware trigger to update the DAC channels. If
> +      not present, the DAC channels are updated by Software LDAC.
> +    maxItems: 1
> +
> +  adi,range-double:
> +    description:
> +      Configure the output range for all channels. If the property is present,
> +      the output will range from 0V to 2 x Vref. If the property is not present,
> +      the output will range from 0V to Vref.

What was the rationale provided for this not being a userspace control?

> +    type: boolean
> +
> +patternProperties:
> +  "^channel@[0-7]$":
> +    $ref: /schemas/iio/dac/dac.yaml#
> +    type: object
> +    description:
> +      Represents the external channels which are connected to the DAC.
> +
> +    properties:
> +      reg:
> +        description: Channel number
> +        minimum: 0
> +        maximum: 7
> +
> +      adi,ch-func:
> +        description:
> +          Channel output type. Use CH_FUNC_VOLTAGE_OUTPUT for voltage
> +          output or CH_FUNC_CURRENT_OUTPUT for current output.
> +        $ref: /schemas/types.yaml#/definitions/uint32

Valid point from sashiko here that you never cover which is which (or
cite the header where the defines come from).
pw-bot: changes-requested

Cheers,
Conor.

> +        enum: [1, 2]
> +
> +    required:
> +      - reg
> +      - adi,ch-func
> +
> +    unevaluatedProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - vdd-supply
> +  - iovdd-supply
> +
> +allOf:
> +  - $ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/iio/addac/adi,ad74413r.h>
> +
> +    spi {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +        dac@0 {
> +            compatible = "adi,ad5710r";
> +            reg = <0>;
> +            spi-max-frequency = <1000000>;
> +            vdd-supply = <&vdd>;
> +            iovdd-supply = <&iovdd>;
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            channel@0 {
> +                reg = <0>;
> +                adi,ch-func = <CH_FUNC_VOLTAGE_OUTPUT>;
> +            };
> +
> +            channel@1 {
> +                reg = <1>;
> +                adi,ch-func = <CH_FUNC_CURRENT_OUTPUT>;
> +            };
> +        };
> +    };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3f5e7b2f524d..ec0f3812199c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1468,6 +1468,7 @@ L:	linux-iio@vger.kernel.org
>  S:	Supported
>  W:	https://ez.analog.com/linux-software-drivers
>  F:	Documentation/devicetree/bindings/iio/dac/adi,ad3530r.yaml
> +F:	Documentation/devicetree/bindings/iio/dac/adi,ad5710r.yaml
>  F:	drivers/iio/dac/ad3530r.c
>  
>  ANALOG DEVICES INC AD3552R DRIVER
> 
> -- 
> 2.34.1
>