Devicetree
 help / color / mirror / Atom feed
From: sashiko-bot@kernel.org
To: "Yu-Chun Lin" <eleanor.lin@realtek.com>
Cc: devicetree@vger.kernel.org, robh@kernel.org, conor+dt@kernel.org
Subject: Re: [PATCH v2 2/2] spi: spi-mem: Add Realtek SPI flash controller driver
Date: Sun, 06 Sep 2026 15:09:55 +0000	[thread overview]
Message-ID: <20260906150956.1EE1D1F00A3A@smtp.kernel.org> (raw)
In-Reply-To: <20260906145755.1230079-3-eleanor.lin@realtek.com>

Thank you for your contribution! Sashiko AI review found 7 potential issue(s) to consider:
- [Critical] The driver fails to configure the hardware's address length dynamically based on the requested `op->addr.nbytes`, relying instead on snooping `EN4B` opcodes, which breaks stateless 4-byte addressing.
- [Critical] The controller's 4-byte addressing mode configuration (SFC_ADR_FOUR_BYTE_EN) is lost across runtime suspends, leading to address truncation and data corruption.
- [High] Multi-byte writes and reads via `exec_op` are fragmented into independent 1-byte SPI transactions due to a byte-wise I/O loop, breaking register accesses and fallback operations.
- [High] The driver intercepts SPI commands and enforces a fixed ~4-second timeout by internally polling the flash WIP bit using a hardcoded RDSR command, breaking long-running operations.
- [High] The driver advertises support for Dual I/O operations for all commands but fails to configure the Dual mode hardware bit for writes and `exec_op` reads.
- [High] The driver lacks bounds checking against the `dirmap` memory resource size, allowing out-of-bounds physical memory accesses.
- [Medium] Unbalanced clk_disable_unprepare() if pm_runtime_get_sync() fails during device removal.
--

commit 76380ef4b88916eb9469e84777c4aa38898c403e
Author: Jyan Chou <jyanchou@realtek.com>

spi: spi-mem: Add Realtek SPI flash controller driver

This commit adds a spi-mem driver for the Realtek SPI Flash Controller
found on DHC SoCs. It implements single and dual I/O transfers with support
for hardware-accelerated dirmap reads and writes.

> diff --git a/drivers/spi/spi-rtk-nor.c b/drivers/spi/spi-rtk-nor.c
> new file mode 100644
> index 0000000000000..0206ea99f3c95
> --- /dev/null
> +++ b/drivers/spi/spi-rtk-nor.c
[ ... ]
> +static int rtk_spi_read_status(struct rtk_spi_host *host)
> +{
> +	int timeout = SFC_DMA_TIMEOUT;
> +	u8 status;
> +
> +	while (timeout--) {
> +		writel(RTK_SPI_OP_RDSR, host->regbase + SFC_OPCODE);
> +		writel(RW_DATAEN, host->regbase + SFC_CTL);
> +
> +		status = readb(host->iobase);
> +		if (!(status & SFC_SR_WIP))
> +			return 0;
> +
> +		usleep_range(100, 200);
> +	}

[Severity: High]
Does this hardcoded loop enforce a fixed timeout of around 4 seconds 
(20,000 iterations of ~200us) for all polled operations? 

Long-running flash operations like Chip Erase might prematurely abort from 
the kernel's perspective even if the hardware continues working. Furthermore,
if a command like Deep Power Down is issued, the flash might stop responding
to RDSR, causing this loop to constantly see 0xFF and eventually time out.

> +
> +	dev_err(host->dev, "Timeout waiting for Flash ready\n");
> +
> +	return -ETIMEDOUT;
> +}
[ ... ]
> +static void rtk_spi_read_mode(struct rtk_spi_host *host, const struct spi_mem_op *op)
> +{
> +	u32 opcode = op->cmd.opcode;
> +	u32 dummy_cycles, val;
> +
> +	if (op->data.buswidth == 2)
> +		opcode |= DUAL_MODE_EN;
> +
> +	writel(opcode, host->regbase + SFC_OPCODE);
> +
> +	val = readl(host->regbase + SFC_CTL);
> +	val |= RW_DATAEN | ADDR_EN;

[Severity: Critical]
Will this instruct the hardware to send an address without ever specifying
its length based on op->addr.nbytes? 

If the spi-nor core issues stateless 4-byte opcodes (where
op->addr.nbytes == 4) without a dedicated EN4B command, the hardware might
only send 3 address bytes, causing data corruption for reading and writing
on flashes larger than 16MB.

> +
> +	dummy_cycles = rtk_spi_calc_dummy_cycles(op);
[ ... ]
> +static void rtk_spi_write_mode(struct rtk_spi_host *host,
> +			       const struct spi_mem_op *op)
> +{
> +	u32 opcode = op->cmd.opcode;
> +	u32 val;
> +
> +	writel(opcode, host->regbase + SFC_OPCODE);
> +
> +	val = readl(host->regbase + SFC_CTL);
> +	val |= RW_DATAEN | ADDR_EN;
> +	writel(val, host->regbase + SFC_CTL);

[Severity: High]
Is the DUAL_MODE_EN bit missing for write operations? 

If the SPI subsystem determines dual mode is supported and issues a
dual-lane write, the flash will expect two lanes of data but the controller
will operate in single-lane mode, which could scramble the bits.

> +}
[ ... ]
> +static int rtk_spi_command_read(struct rtk_spi_host *host, const struct spi_mem_op *op)
> +{
> +	size_t len = op->data.nbytes;
> +	loff_t offset = op->addr.val;
> +	u8 opcode = op->cmd.opcode;
> +	u32 dummy_cycles, val;
> +
> +	writel(opcode, host->regbase + SFC_OPCODE);

[Severity: High]
Similarly to the write mode setup, is the DUAL_MODE_EN bit also omitted here
when exec_op is used for fallback dual reads?

> +
> +	val = readl(host->regbase + SFC_CTL);
> +	val &= ~(SFC_CTL_DMYCNT_MASK | ADDR_EN);
> +	val |= RW_DATAEN;
> +
> +	if (op->addr.nbytes > 0)
> +		val |= ADDR_EN;
> +
> +	dummy_cycles = rtk_spi_calc_dummy_cycles(op);
> +	val |= (dummy_cycles << SFC_CTL_DMYCNT_SHIFT) & SFC_CTL_DMYCNT_MASK;
> +	writel(val, host->regbase + SFC_CTL);
> +
> +	memcpy_fromio(op->data.buf.in, host->iobase + offset, len);

[Severity: High]
Could this memory I/O read split restart address-less commands like RDID
multiple times since it triggers discrete read transactions?

Also, is there any bounds checking against the mapped dirmap resource size?
If offset (derived from op->addr.val) or len exceeds the physical memory
window mapped by devm_ioremap_resource(), it could lead to out-of-bounds
physical memory accesses, kernel panics, or Data Aborts.

> +
> +	return 0;
> +}
> +
> +static int rtk_spi_do_write_and_cmds(struct rtk_spi_host *host, const struct spi_mem_op *op)
> +{
> +	u8 opcode = op->cmd.opcode;
> +	u32 ctl_val = 0;
> +	int ret = 0;
> +
> +	writel(opcode, host->regbase + SFC_OPCODE);
> +
> +	if (op->data.nbytes > 0)
> +		ctl_val |= RW_DATAEN;
> +	if (op->addr.nbytes > 0)
> +		ctl_val |= ADDR_EN;
> +
> +	writel(ctl_val, host->regbase + SFC_CTL);
> +
> +	if (op->data.nbytes > 0) {
> +		const u8 *buf = op->data.buf.out;
> +		size_t i;
> +
> +		for (i = 0; i < op->data.nbytes; i++)
> +			writeb(buf[i], host->iobase + op->addr.val + i);

[Severity: High]
Does this byte-wise loop fragment a contiguous write transfer into
independent 1-byte SPI transactions? 

Each writeb to the mapped memory generates a discrete bus sequence (CS
assert -> command -> data -> CS deassert). Commands requiring multiple
contiguous data bytes, like WRSR or fallback Page Programs, could fail
or corrupt state.

Also, similar to rtk_spi_command_read(), this seems to write directly to
physical memory using an unbounded op->addr.val, which could exceed the
size of the mapped dirmap resource.

> +	} else if (op->addr.nbytes > 0) {
> +		readb(host->iobase + op->addr.val);
> +
> +		/* Wait for internal flash erase/programming to complete */
> +		ret = rtk_spi_read_status(host);
> +	} else {
> +		readb(host->iobase);
> +
> +		/*
> +		 * For pure commands that require internal state synchronization
> +		 * (such as Chip Erase), poll the flash status.
> +		 */
> +		ret = rtk_spi_read_status(host);

[Severity: High]
Does this intercept the spi-mem command completion and force the hardware
driver to synchronously poll the flash status internally? 

This polling is usually intended for the spi-nor core, and combined with
the ~4-second timeout, could cause longer operations like Chip Erase to
abort prematurely.

> +	}
> +
> +	if (ret) {
> +		dev_err(host->dev, "opcode 0x%02x failed: %d\n", opcode, ret);
> +		return ret;
> +	}
> +
> +	/*
> +	 * Hardware Workaround:
> +	 * The controller's auto-mode engine requires SFC_ADR_FOUR_BYTE_EN to be
> +	 * explicitly updated when the flash enters or exits 4-byte mode via control
> +	 * commands.
> +	 */
> +	if (opcode == RTK_SPI_OP_EN4B)
> +		writel(0x1, host->regbase + SFC_ADR_FOUR_BYTE_EN);
> +	else if (opcode == RTK_SPI_OP_EX4B)
> +		writel(0x0, host->regbase + SFC_ADR_FOUR_BYTE_EN);

[Severity: Critical]
Is it possible for the hardware to get permanently stuck in 3-byte address
mode if the spi-nor core uses stateless 4-byte opcodes instead of explicitly
issuing EN4B? 

Additionally, this dynamic SFC_ADR_FOUR_BYTE_EN state appears to be lost
across runtime suspends because rtk_spi_runtime_resume() resets the hardware
and does not restore this setting. If the controller resumes and defaults
back to 3-byte mode while the flash chip is in 4-byte mode, subsequent
reads and writes could be globally corrupted.

> +
> +	return ret;
> +}
[ ... ]
> +static bool rtk_spi_supports_op(struct spi_mem *mem,
> +				const struct spi_mem_op *op)
> +{
> +	if (op->cmd.buswidth != 1)
> +		return false;
> +
> +	if (op->cmd.dtr || op->addr.dtr || op->data.dtr)
> +		return false;
> +
> +	if (op->addr.nbytes != 0) {
> +		if (op->addr.buswidth > 1)
> +			return false;
> +		if (op->addr.nbytes < 3 || op->addr.nbytes > 4)
> +			return false;
> +	}
> +
> +	if (op->dummy.nbytes != 0) {
> +		if (op->dummy.buswidth > 1 || op->dummy.nbytes > 7)
> +			return false;
> +	}
> +
> +	if (op->data.nbytes != 0 && op->data.buswidth > 2)
> +		return false;

[Severity: High]
Does this check allow 2-lane wide writes to proceed? 

As noted in rtk_spi_write_mode(), the hardware is not configured with
DUAL_MODE_EN for writes, leading to a mismatch between what is advertised
here and what the controller actually does.

> +
> +	return spi_mem_default_supports_op(mem, op);
> +}
> +
> +static int rtk_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
> +{

[Severity: High]
Does this function fail to check if desc->info.length exceeds the hardware's
mapped memory window size? 

Failing to reject oversized dirmap descriptions could result in out-of-bounds
physical memory accesses later during transfers.

> +	const struct spi_mem_op *op = desc->info.op_tmpl;
> +
> +	if (op->data.dir == SPI_MEM_DATA_IN && op->addr.nbytes != 3 && op->addr.nbytes != 4)
> +		return -EOPNOTSUPP;
[ ... ]
> +static void rtk_spi_remove(struct platform_device *pdev)
> +{
> +	struct spi_controller *ctrl = platform_get_drvdata(pdev);
> +	struct rtk_spi_host *host = spi_controller_get_devdata(ctrl);
> +	struct device *dev = &pdev->dev;
> +
> +	spi_unregister_controller(ctrl);
> +
> +	pm_runtime_get_sync(dev);
> +	pm_runtime_disable(dev);
> +	clk_disable_unprepare(host->clk);

[Severity: Medium]
If pm_runtime_get_sync(dev) fails during module removal (for instance, when
the device is suspended and runtime resume encounters an error), the device
clock is not enabled. 

Will this lead to an unbalanced clk_disable_unprepare() call and a clock
enable count underflow?

> +	pm_runtime_put_noidle(dev);
> +	pm_runtime_set_suspended(dev);
> +}
[ ... ]
> +static int rtk_spi_runtime_resume(struct device *dev)
> +{
> +	struct spi_controller *ctlr = dev_get_drvdata(dev);
> +	struct rtk_spi_host *host = spi_controller_get_devdata(ctlr);
> +	int ret;
> +
> +	ret = clk_prepare_enable(host->clk);
> +	if (ret < 0) {
> +		dev_err(dev, "clk_prepare_enable failed: %d\n", ret);
> +		return ret;
> +	}
> +
> +	reset_control_assert(host->rstc);
> +	usleep_range(10, 20);
> +	reset_control_deassert(host->rstc);
> +
> +	rtk_spi_init(host);

[Severity: Critical]
When the hardware is reset and initialized upon resume, the dynamic 
SFC_ADR_FOUR_BYTE_EN state is wiped. 

Since rtk_spi_init() doesn't restore this state, could the controller revert
to 3-byte address mode while the flash chip remains in 4-byte mode, leading
to address truncation and data corruption?

> +
> +	return 0;
> +}

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260906145755.1230079-1-eleanor.lin@realtek.com?part=2

  reply	other threads:[~2026-09-06 15:10 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-09-06 14:57 [PATCH v2 0/2] spi: realtek: Add support for RTD1625 SPI Flash Controller Yu-Chun Lin
2026-09-06 14:57 ` [PATCH v2 1/2] dt-bindings: spi: Add Realtek RTD1625 SPI support Yu-Chun Lin
2026-09-07 17:29   ` Conor Dooley
2026-09-06 14:57 ` [PATCH v2 2/2] spi: spi-mem: Add Realtek SPI flash controller driver Yu-Chun Lin
2026-09-06 15:09   ` sashiko-bot [this message]
2026-09-06 15:18   ` Kuan-Wei Chiu
2026-09-07 13:47   ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260906150956.1EE1D1F00A3A@smtp.kernel.org \
    --to=sashiko-bot@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=eleanor.lin@realtek.com \
    --cc=robh@kernel.org \
    --cc=sashiko-reviews@lists.linux.dev \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox