[PATCH 4/4] arm64: dts: qcom: nord-rrd: Enable eDP0/1 display output

[Shawn Guo <shengchao.guo@oss.qualcomm.com>]

From: Ritesh Kumar <ritesh.kumar@oss.qualcomm.com>

Enable the MDSS, DP0/1 controllers and eDP0/1 PHYs on the Nord RRD
board and describe the eDP0/1 connector, its 4 data lanes and supported
link frequencies.

Signed-off-by: Ritesh Kumar <ritesh.kumar@oss.qualcomm.com>
Signed-off-by: Nabige Aala <nabige.aala@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/nord-rrd.dts | 62 +++++++++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/nord-rrd.dts b/arch/arm64/boot/dts/qcom/nord-rrd.dts
index c547963371b4..802987da3cfd 100644
--- a/arch/arm64/boot/dts/qcom/nord-rrd.dts
+++ b/arch/arm64/boot/dts/qcom/nord-rrd.dts
@@ -53,6 +53,30 @@ bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk {
 			clock-div = <2>;
 		};
 	};
+
+	dp0_connector: connector-dp0 {
+		compatible = "dp-connector";
+		label = "eDP0";
+		type = "full-size";
+
+		port {
+			dp0_connector_in: endpoint {
+				remote-endpoint = <&mdss_dp0_out>;
+			};
+		};
+	};
+
+	dp1_connector: connector-dp1 {
+		compatible = "dp-connector";
+		label = "eDP1";
+		type = "full-size";
+
+		port {
+			dp1_connector_in: endpoint {
+				remote-endpoint = <&mdss_dp1_out>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -366,6 +390,20 @@ vreg_l3l_1p8: ldo3 {
 	};
 };
 
+&dp0_phy {
+	vdda-phy-supply = <&vreg_l2h_1p2>;
+	vdda-pll-supply = <&vreg_l1h_0p9>;
+
+	status = "okay";
+};
+
+&dp1_phy {
+	vdda-phy-supply = <&vreg_l2h_1p2>;
+	vdda-pll-supply = <&vreg_l1h_0p9>;
+
+	status = "okay";
+};
+
 &i2c7 {
 	clock-frequency = <400000>;
 
@@ -377,6 +415,30 @@ rtc@32 {
 	};
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+	remote-endpoint = <&dp0_connector_in>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+	remote-endpoint = <&dp1_connector_in>;
+};
+
 &qupv3_0 {
 	firmware-name = "qcom/nord/qupv3fw.elf";
 
-- 
2.43.0