[PATCH v3 4/4] arm64: dts: qcom: milos-fairphone-fp6: Enable display

[Luca Weiss <luca.weiss@fairphone.com>]

Configure the MDSS nodes for the phone and add the panel node.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
---
 arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts | 64 ++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts b/arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts
index 4e8777162b53..11015c3fa331 100644
--- a/arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts
+++ b/arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts
@@ -709,6 +709,49 @@ &ipa {
 	status = "okay";
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l4b>;
+
+	status = "okay";
+
+	panel@0 {
+		compatible = "boe,bj631jhm-t71-d900";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+		vci-supply = <&vreg_l19b>;
+		vddio-supply = <&vreg_l9b>;
+		dvdd-supply = <&vreg_oled_dvdd_1p2>;
+
+		pinctrl-0 = <&disp_reset_n_active>, <&mdp_vsync>;
+		pinctrl-1 = <&disp_reset_n_suspend>, <&mdp_vsync>;
+		pinctrl-names = "default",
+				"sleep";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&panel_in>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l2b>;
+
+	status = "okay";
+};
+
 &pm8550vs_c {
 	status = "okay";
 };
@@ -872,6 +915,20 @@ &tlmm {
 			       <13 1>, /* NC */
 			       <63 2>; /* WLAN UART */
 
+	disp_reset_n_active: disp-reset-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	disp_reset_n_suspend: disp-reset-n-suspend-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
 	sdc2_card_det_n: sdc2-card-det-state {
 		pins = "gpio65";
 		function = "gpio";
@@ -906,6 +963,13 @@ pm8008_int_default: pm8008-int-default-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	mdp_vsync: mdp-vsync-state {
+		pins = "gpio129";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
 };
 
 &uart5 {

-- 
2.56.0