[PATCH net-next v9 10/11] net: phy: ncn26000: Support for onsemi's S2500 internal phy

[Selvamani Rajagopal via B4 Relay <devnull+Selvamani.Rajagopal.onsemi.com@kernel.org>]

From: Selvamani Rajagopal <Selvamani.Rajagopal@onsemi.com>

Adding support for internal PHY of the integrated
media access controller S2500. PLCA tx opportunity timer's
default value is correct in this device, compared to
the currently supported PHY NCN26000.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Selvamani Rajagopal <Selvamani.Rajagopal@onsemi.com>

---
changes in v9
  - Added Reviewed tag
changes in v8
  - changes to use newer API for read/write_mmd callback
changes in v7
  - No change
changes in v6
  - No change
changes in v5
  - No change
changes in v4
  - no change
changes in v3
   added new PHY support separate patch
   changed model comparison to use phy_id_compare_model
changes in v2
   Removed bug fixes. Retained only S2500 specific changes
changes in v1
   Added support for an internal PHY of onsemi's MAC-PHY S2500
---
 MAINTAINERS                |  1 +
 drivers/net/phy/ncn26000.c | 36 ++++++++++++++++++++++++++++++++----
 2 files changed, 33 insertions(+), 4 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 4e122a5eefa1..c114be851607 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -20435,6 +20435,7 @@ F:	arch/mips/boot/dts/ralink/omega2p.dts
 
 ONSEMI ETHERNET PHY DRIVERS
 M:	Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
+M:	Selva Rajagopal <selvamani.rajagopal@onsemi.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 W:	http://www.onsemi.com
diff --git a/drivers/net/phy/ncn26000.c b/drivers/net/phy/ncn26000.c
index 6d433f4e2c45..a33ebb2a7ece 100644
--- a/drivers/net/phy/ncn26000.c
+++ b/drivers/net/phy/ncn26000.c
@@ -2,7 +2,7 @@
 /*
  *  Driver for the onsemi 10BASE-T1S NCN26000 PHYs family.
  *
- * Copyright 2022 onsemi
+ * Copyright 2026 onsemi
  */
 #include <linux/kernel.h>
 #include <linux/bitfield.h>
@@ -14,6 +14,7 @@
 
 #include "mdio-open-alliance.h"
 
+#define PHY_ID_S2500			0x180FF411
 #define PHY_ID_NCN26000			0x180FF5A1
 
 #define NCN26000_REG_IRQ_CTL            16
@@ -41,13 +42,18 @@
 
 static int ncn26000_config_init(struct phy_device *phydev)
 {
+	int ret = 0;
+
 	/* HW bug workaround: the default value of the PLCA TO_TIMER should be
 	 * 32, where the current version of NCN26000 reports 24. This will be
 	 * fixed in future PHY versions. For the time being, we force the
 	 * correct default here.
 	 */
-	return phy_write_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_TOTMR,
-			     TO_TMR_DEFAULT);
+	if (phy_id_compare_model(phydev->drv->phy_id, PHY_ID_NCN26000))
+		ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
+				    MDIO_OATC14_PLCA_TOTMR,
+				    TO_TMR_DEFAULT);
+	return ret;
 }
 
 static int ncn26000_config_aneg(struct phy_device *phydev)
@@ -139,8 +145,8 @@ static irqreturn_t ncn26000_handle_interrupt(struct phy_device *phydev)
 
 static int ncn26000_config_intr(struct phy_device *phydev)
 {
-	int ret;
 	u16 irqe;
+	int ret;
 
 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
 		// acknowledge IRQs
@@ -163,6 +169,26 @@ static int ncn26000_config_intr(struct phy_device *phydev)
 }
 
 static struct phy_driver ncn26000_driver[] = {
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_S2500),
+		.name                  = "S2500",
+		.features              = PHY_BASIC_T1S_P2MP_FEATURES,
+		.config_init           = ncn26000_config_init,
+		.config_intr           = ncn26000_config_intr,
+		.config_aneg           = ncn26000_config_aneg,
+		.read_status           = ncn26000_read_status,
+		.handle_interrupt      = ncn26000_handle_interrupt,
+		.set_plca_cfg          = ncn26000_c45_plca_set_cfg,
+		.get_plca_cfg          = genphy_c45_plca_get_cfg,
+		.get_plca_status       = genphy_c45_plca_get_status,
+		.soft_reset            = genphy_soft_reset,
+		.get_sqi               = genphy_c45_oatc14_get_sqi,
+		.get_sqi_max           = genphy_c45_oatc14_get_sqi_max,
+		.read_mmd              = genphy_read_mmd_c45,
+		.write_mmd             = genphy_write_mmd_c45,
+		.cable_test_get_status = genphy_c45_oatc14_cable_test_get_status,
+		.cable_test_start      = genphy_c45_oatc14_cable_test_start,
+	},
 	{
 		PHY_ID_MATCH_MODEL(PHY_ID_NCN26000),
 		.name			= "NCN26000",
@@ -183,11 +209,13 @@ module_phy_driver(ncn26000_driver);
 
 static const struct mdio_device_id __maybe_unused ncn26000_tbl[] = {
 	{ PHY_ID_MATCH_MODEL(PHY_ID_NCN26000) },
+	{ PHY_ID_MATCH_MODEL(PHY_ID_S2500) },
 	{ }
 };
 
 MODULE_DEVICE_TABLE(mdio, ncn26000_tbl);
 
+MODULE_AUTHOR("Selva Rajagopal <selvamani.rajagopal@onsemi.com>");
 MODULE_AUTHOR("Piergiorgio Beruto");
 MODULE_DESCRIPTION("onsemi 10BASE-T1S PHY driver");
 MODULE_LICENSE("Dual BSD/GPL");

-- 
2.43.0