Devicetree
 help / color / mirror / Atom feed
From: Luo Liu <Luo.Liu@cixtech.com>
To: maarten.lankhorst@linux.intel.com, mripard@kernel.org,
	tzimmermann@suse.de, robh@kernel.org, krzk+dt@kernel.org,
	conor+dt@kernel.org
Cc: dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
	Luo.Liu@cixtech.com, wuyi.shen@cixtech.com,
	cix-kernel-upstream@cixtech.com
Subject: [PATCH v2 0/2] drm/cix: add Sky1 DisplayPort transmitter
Date: Tue, 17 Nov 2026 14:45:50 +0800	[thread overview]
Message-ID: <20261117064552.85256-1-Luo.Liu@cixtech.com> (raw)

Add the CIX Sky1 DisplayPort transmitter as a DRM bridge. The USB-C
transmitters and the native DP/eDP transmitter use separate compatibles
because their RCSU video-adapter layouts differ. The Sky1 devicetree
nodes are not included in this posting.

Scope: DPTX hardware and bindings only. Komeda (the Sky1 display
controller that feeds these bridges) and the board DTS are separate
series. Nothing in this posting wires a full display stack.

Connector handling in this driver:

  The Komeda display pipeline (ARM Mali DPU on Sky1, posted separately)
  calls drm_bridge_attach() with attach flags 0 and does not register a
  connector for these DP outputs. This driver therefore registers a
  DisplayPort drm_connector from bridge .attach(). Detect, EDID read, mode
  enumeration and validation run through drm_connector_funcs and helper
  hooks on that connector.

v1 -> v2:
- Split the compatible into "cix,sky1-usbdp" and "cix,sky1-dp", and
  rename the binding to cix,sky1-dp.yaml.
- Drop cix,adapter-port, cix,stream-id and cix,dp-max-rate. Every
  transmitter uses stream 0, and the maximum link rate is HBR2.
- Require phys and port in the binding; example follows Sky1-Orion graph
  (DPU pipeline@0 to DPTX, USB-C dp-port PHY).
- Keep only the documented DPTX node in the binding example; reference
  the DPU and USB-C PHY through phandles instead of copying their nodes.
- Allow COMPILE_TEST.
- Serialize mode selection with link retraining, and roll back the PHY
  and the IRQ disable depth when enable or resume fails.
- Pair phy_init/phy_exit with host_init/deinit; use phy_power_on/off
  only from core_on/off.
- Stop active streams before host teardown on remove and shutdown.
- Match YCbCr 4:2:0 against the original CEA mode, and avoid a 64-bit
  division in the pixel-clock adjustment.
- Initialize train_done before the clock-recovery and channel-equalization
  loops.
- Serialize sessions with a plain mutex and AUX with a separate lock
  instead of a hand-written recursive lock; use ops->session_lock in DRM
  paths and _locked helpers for the internal steps. Document the
  session_lock -> aux_lock order.
- Roll back the bridge enable path with an explicit unprepare step when
  mode selection or stream enable fails.
- Poll the PHY ready status with readl_poll_timeout(), check only the
  AUX reply field that matches the request type, and drop the redundant
  DPCD power-up retry loop.
- Wait for AUX reply with readl_poll_timeout(); register devm teardown
  via devm_add_action_or_reset().
- Document INTERRUPT_CAUSE read-to-clear (Sky1 TRM).
- Use GENMASK()/FIELD_PREP() for adapter format fields; drop unused
  link-training parameters.

Luo Liu (2):
  dt-bindings: display: add CIX Sky1 DisplayPort transmitter
  drm/cix: add Sky1 DisplayPort transmitter driver

 .../bindings/display/cix,sky1-dp.yaml         |   99 +
 MAINTAINERS                                   |    9 +
 drivers/gpu/drm/Kconfig                       |    1 +
 drivers/gpu/drm/Makefile                      |    1 +
 drivers/gpu/drm/cix/Kconfig                   |    3 +
 drivers/gpu/drm/cix/Makefile                  |    3 +
 drivers/gpu/drm/cix/dptx/Kconfig              |   17 +
 drivers/gpu/drm/cix/dptx/Makefile             |    4 +
 drivers/gpu/drm/cix/dptx/cix_dptx.c           | 2434 +++++++++++++++++
 drivers/gpu/drm/cix/dptx/cix_dptx.h           |  408 +++
 drivers/gpu/drm/cix/dptx/cix_dptx_drm.c       |  771 ++++++
 drivers/gpu/drm/cix/dptx/cix_dptx_drm.h       |   16 +
 12 files changed, 3766 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/cix,sky1-dp.yaml
 create mode 100644 drivers/gpu/drm/cix/Kconfig
 create mode 100644 drivers/gpu/drm/cix/Makefile
 create mode 100644 drivers/gpu/drm/cix/dptx/Kconfig
 create mode 100644 drivers/gpu/drm/cix/dptx/Makefile
 create mode 100644 drivers/gpu/drm/cix/dptx/cix_dptx.c
 create mode 100644 drivers/gpu/drm/cix/dptx/cix_dptx.h
 create mode 100644 drivers/gpu/drm/cix/dptx/cix_dptx_drm.c
 create mode 100644 drivers/gpu/drm/cix/dptx/cix_dptx_drm.h


base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4

             reply	other threads:[~2026-11-17  6:46 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-17  6:45 Luo Liu [this message]
2026-11-17  6:45 ` [PATCH v2 1/2] dt-bindings: display: add CIX Sky1 DisplayPort transmitter Luo Liu
2026-11-17  6:45 ` [PATCH v2 2/2] drm/cix: add Sky1 DisplayPort transmitter driver Luo Liu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20261117064552.85256-1-Luo.Liu@cixtech.com \
    --to=luo.liu@cixtech.com \
    --cc=cix-kernel-upstream@cixtech.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=krzk+dt@kernel.org \
    --cc=maarten.lankhorst@linux.intel.com \
    --cc=mripard@kernel.org \
    --cc=robh@kernel.org \
    --cc=tzimmermann@suse.de \
    --cc=wuyi.shen@cixtech.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox