[PATCH v2 00/10] Add basic support for Rockchip RK1108 SOC

[PATCH v2 00/10] Add basic support for Rockchip RK1108 SOC

[Andy Yan]

RK1108 is embedded with an ARM Cortex-A7 single core and a DSP core.
It is designed for varies application scenario such as car DVR, sports
DV, secure camera and UAV camera.
This patch series add basic support for it, which can boot a board with
initramfs into shell.
More new feathers will come soon.

Changes in v2:
- split dt-binding header from clk driver
- fix some CodingStyle issues
- add dt-binding documentation for pinctrl
- add pull and drive-strength functionality for pinctrl
- fix timer and gic dt description
- ordering devices by register address
- move the board in the rockchip.txt to the block of Rockchip boards

Andy Yan (6):
  dt-bindings: add documentation for rk1108 pinctrl
  pinctrl: rockchip: add support for rk1108
  ARM: add low level debug uart for rk1108
  ARM: dts: add basic support for Rockchip RK1108 SOC
  ARM: rockchip: enable support for RK1108 SoC
  ARM: dts: rockchip: add rockchip RK1108 Evaluation board

Shawn Lin (4):
  dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description
  dt-bindings: add documentation for rk1108 cru
  clk: rockchip: add dt-binding header for rk1108
  clk: rockchip: add clock controller for rk1108

 Documentation/devicetree/bindings/arm/rockchip.txt |   5 +-
 .../bindings/clock/rockchip,rk1108-cru.txt         |  60 +++
 .../devicetree/bindings/mmc/rockchip-dw-mshc.txt   |   1 +
 .../bindings/pinctrl/rockchip,pinctrl.txt          |   9 +-
 arch/arm/Kconfig.debug                             |  30 ++
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/rk1108-evb.dts                   |  69 ++++
 arch/arm/boot/dts/rk1108.dtsi                      | 428 +++++++++++++++++++
 arch/arm/mach-rockchip/rockchip.c                  |   1 +
 drivers/clk/rockchip/Makefile                      |   1 +
 drivers/clk/rockchip/clk-rk1108.c                  | 451 +++++++++++++++++++++
 drivers/clk/rockchip/clk.h                         |  14 +
 drivers/pinctrl/pinctrl-rockchip.c                 |  87 +++-
 include/dt-bindings/clock/rk1108-cru.h             | 270 ++++++++++++
 14 files changed, 1421 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
 create mode 100644 arch/arm/boot/dts/rk1108-evb.dts
 create mode 100644 arch/arm/boot/dts/rk1108.dtsi
 create mode 100644 drivers/clk/rockchip/clk-rk1108.c
 create mode 100644 include/dt-bindings/clock/rk1108-cru.h

-- 
2.7.4

[PATCH v2 01/10] dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description

[Andy Yan]

From: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

Add "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc" for
dwmmc on rk1108 platform.

Signed-off-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

---

Changes in v2: None

 Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
index 07184e8..ea9c1c9 100644
--- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
@@ -13,6 +13,7 @@ Required Properties:
 	- "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following,
 							before RK3288
 	- "rockchip,rk3288-dw-mshc": for Rockchip RK3288
+	- "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK1108
 	- "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036
 	- "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368
 	- "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399
-- 
2.7.4

Re: [PATCH v2 01/10] dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description

[Heiko Stuebner]

Am Montag, 14. November 2016, 20:01:05 CET schrieb Andy Yan:
> From: Shawn Lin <shawn.lin@rock-chips.com>
> 
> Add "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc" for
> dwmmc on rk1108 platform.
> 
> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>

applied to my dts32 branch with Rob's Ack taken from the unchanged v1.


Heiko

[PATCH v2 02/10] dt-bindings: add documentation for rk1108 cru

[Andy Yan]

From: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

This adds the dt-binding documentation for the clock and reset unit
found on Rockchip rk1108 SoCs.

Signed-off-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
---

Changes in v2: None

 .../bindings/clock/rockchip,rk1108-cru.txt         | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt

diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
new file mode 100644
index 0000000..4d2356b
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
@@ -0,0 +1,60 @@
+* Rockchip RK1108 Clock and Reset Unit
+
+The RK1108 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk1108-cru"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+  If missing pll rates are not changeable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk1108-cru.h headers and can be
+used in device tree sources. Similar macros exist for the reset sources in
+these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "cif_clkout" - output clock for the cif - optional
+ - "mipi_csi_clkout" - output clock for the mipi csi - optional
+ - "pclkin_vip" - external VIP clock - optional
+ - "ext_i2s" - external I2S clock - optional
+ - "ext_gmac" - external GMAC clock - optional
+ - "mac_ref_clkout" - output clock of the pll in the mac phy
+
+Example: Clock controller node:
+
+	cru: cru@20200000 {
+		compatible = "rockchip,rk1108-cru";
+		reg = <0x20200000 0x1000>;
+		rockchip,grf = <&grf>;
+
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller:
+
+	uart0: serial@10230000 {
+		compatible = "rockchip,rk1108-uart", "snps,dw-apb-uart";
+		reg = <0x10230000 0x100>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clocks = <&cru SCLK_UART0>;
+	};
-- 
2.7.4


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 02/10] dt-bindings: add documentation for rk1108 cru

[Heiko Stuebner]

Hi Andy,

Am Montag, 14. November 2016, 20:03:01 CET schrieb Andy Yan:
> From: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> 
> This adds the dt-binding documentation for the clock and reset unit
> found on Rockchip rk1108 SoCs.
> 
> Signed-off-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> ---
> 
> Changes in v2: None
> 
>  .../bindings/clock/rockchip,rk1108-cru.txt         | 60
> ++++++++++++++++++++++ 1 file changed, 60 insertions(+)
>  create mode 100644
> Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
> 
> diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
> b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt new file
> mode 100644
> index 0000000..4d2356b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
> @@ -0,0 +1,60 @@
> +* Rockchip RK1108 Clock and Reset Unit
> +
> +The RK1108 clock controller generates and supplies clock to various
> +controllers within the SoC and also implements a reset controller for SoC
> +peripherals.
> +
> +Required Properties:
> +
> +- compatible: should be "rockchip,rk1108-cru"
> +- reg: physical base address of the controller and length of memory mapped
> +  region.
> +- #clock-cells: should be 1.
> +- #reset-cells: should be 1.
> +
> +Optional Properties:
> +
> +- rockchip,grf: phandle to the syscon managing the "general register files"
> +  If missing pll rates are not changeable, due to the missing pll lock
> status. +
> +Each clock is assigned an identifier and client nodes can use this
> identifier +to specify the clock which they consume. All available clocks
> are defined as +preprocessor macros in the dt-bindings/clock/rk1108-cru.h
> headers and can be +used in device tree sources. Similar macros exist for
> the reset sources in +these files.
> +
> +External clocks:
> +
> +There are several clocks that are generated outside the SoC. It is expected
> +that they are defined using standard clock bindings with following
> +clock-output-names:
> + - "xin24m" - crystal input - required,
> + - "cif_clkout" - output clock for the cif - optional
> + - "mipi_csi_clkout" - output clock for the mipi csi - optional
> + - "pclkin_vip" - external VIP clock - optional
> + - "ext_i2s" - external I2S clock - optional
> + - "ext_gmac" - external GMAC clock - optional
> + - "mac_ref_clkout" - output clock of the pll in the mac phy

we really only want to list the actual input clocks here, not outputs.

Also, the list of actual input clocks seems incomplete (hdmiphy, usbphy) and 
some clocks listed here do not match the clock controller 2 patches later 
(pclkin_vip, ext_gmac [rk1108 only has 10/100], ext_i2s, ...)


Heiko
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 02/10] dt-bindings: add documentation for rk1108 cru

[Shawn Lin]

On 2016/11/15 17:35, Heiko Stuebner wrote:
> Hi Andy,
>
> Am Montag, 14. November 2016, 20:03:01 CET schrieb Andy Yan:
>> From: Shawn Lin <shawn.lin@rock-chips.com>
>>
>> This adds the dt-binding documentation for the clock and reset unit
>> found on Rockchip rk1108 SoCs.
>>
>> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
>> Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
>> ---
>>
>> Changes in v2: None
>>
>>  .../bindings/clock/rockchip,rk1108-cru.txt         | 60
>> ++++++++++++++++++++++ 1 file changed, 60 insertions(+)
>>  create mode 100644
>> Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
>>
>> diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
>> b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt new file
>> mode 100644
>> index 0000000..4d2356b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/rockchip,rk1108-cru.txt
>> @@ -0,0 +1,60 @@
>> +* Rockchip RK1108 Clock and Reset Unit
>> +
>> +The RK1108 clock controller generates and supplies clock to various
>> +controllers within the SoC and also implements a reset controller for SoC
>> +peripherals.
>> +
>> +Required Properties:
>> +
>> +- compatible: should be "rockchip,rk1108-cru"
>> +- reg: physical base address of the controller and length of memory mapped
>> +  region.
>> +- #clock-cells: should be 1.
>> +- #reset-cells: should be 1.
>> +
>> +Optional Properties:
>> +
>> +- rockchip,grf: phandle to the syscon managing the "general register files"
>> +  If missing pll rates are not changeable, due to the missing pll lock
>> status. +
>> +Each clock is assigned an identifier and client nodes can use this
>> identifier +to specify the clock which they consume. All available clocks
>> are defined as +preprocessor macros in the dt-bindings/clock/rk1108-cru.h
>> headers and can be +used in device tree sources. Similar macros exist for
>> the reset sources in +these files.
>> +
>> +External clocks:
>> +
>> +There are several clocks that are generated outside the SoC. It is expected
>> +that they are defined using standard clock bindings with following
>> +clock-output-names:
>> + - "xin24m" - crystal input - required,
>> + - "cif_clkout" - output clock for the cif - optional
>> + - "mipi_csi_clkout" - output clock for the mipi csi - optional
>> + - "pclkin_vip" - external VIP clock - optional
>> + - "ext_i2s" - external I2S clock - optional
>> + - "ext_gmac" - external GMAC clock - optional
>> + - "mac_ref_clkout" - output clock of the pll in the mac phy
>
> we really only want to list the actual input clocks here, not outputs.
>
> Also, the list of actual input clocks seems incomplete (hdmiphy, usbphy) and
> some clocks listed here do not match the clock controller 2 patches later
> (pclkin_vip, ext_gmac [rk1108 only has 10/100], ext_i2s, ...)
>

yup, I was just listing the basic clock for Andy to bring up rk1108
board, so some of them was missing here. I will fix them here as well
as adding all of the input clocks in the clock driver. :)

>
> Heiko
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>


-- 
Best Regards
Shawn Lin

[PATCH v2 03/10] clk: rockchip: add dt-binding header for rk1108

[Andy Yan]

From: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

Add the dt-bindings header for the rk1108, that gets shared
between the clock controller and the clock references in the dts.

Signed-off-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
---

Changes in v2:
- split dt-binding header from clk driver

 include/dt-bindings/clock/rk1108-cru.h | 270 +++++++++++++++++++++++++++++++++
 1 file changed, 270 insertions(+)
 create mode 100644 include/dt-bindings/clock/rk1108-cru.h

diff --git a/include/dt-bindings/clock/rk1108-cru.h b/include/dt-bindings/clock/rk1108-cru.h
new file mode 100644
index 0000000..6f30008
--- /dev/null
+++ b/include/dt-bindings/clock/rk1108-cru.h
@@ -0,0 +1,270 @@
+/*
+ * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
+ * Author: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
+#define _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
+
+/* pll id */
+#define RK1108_APLL_ID			0
+#define RK1108_DPLL_ID			1
+#define RK1108_GPLL_ID			2
+#define RK1108_ARMCLK			3
+
+/* sclk gates (special clocks) */
+#define SCLK_SPI0			65
+#define SCLK_NANDC			67
+#define SCLK_SDMMC			68
+#define SCLK_SDIO			69
+#define SCLK_EMMC			71
+#define SCLK_UART0			72
+#define SCLK_UART1			73
+#define SCLK_UART2			74
+#define SCLK_I2S0			75
+#define SCLK_I2S1			76
+#define SCLK_I2S2			77
+#define SCLK_TIMER0			78
+#define SCLK_TIMER1			79
+#define SCLK_SFC			80
+#define SCLK_SDMMC_DRV			81
+#define SCLK_SDIO_DRV			82
+#define SCLK_EMMC_DRV			83
+#define SCLK_SDMMC_SAMPLE		84
+#define SCLK_SDIO_SAMPLE		85
+#define SCLK_EMMC_SAMPLE		86
+
+/* aclk gates */
+#define ACLK_DMAC			251
+#define ACLK_PRE			252
+#define ACLK_CORE			253
+#define ACLK_ENMCORE			254
+
+/* pclk gates */
+#define PCLK_GPIO1			321
+#define PCLK_GPIO2			322
+#define PCLK_GPIO3			323
+#define PCLK_GRF			329
+#define PCLK_I2C1			333
+#define PCLK_I2C2			334
+#define PCLK_I2C3			335
+#define PCLK_SPI			338
+#define PCLK_SFC			339
+#define PCLK_UART0			341
+#define PCLK_UART1			342
+#define PCLK_UART2			343
+#define PCLK_TSADC			344
+#define PCLK_PWM			350
+#define PCLK_TIMER			353
+#define PCLK_PERI			363
+
+/* hclk gates */
+#define HCLK_I2S0_8CH			442
+#define HCLK_I2S1_8CH			443
+#define HCLK_I2S2_2CH			444
+#define HCLK_NANDC			453
+#define HCLK_SDMMC			456
+#define HCLK_SDIO			457
+#define HCLK_EMMC			459
+#define HCLK_PERI			478
+#define HCLK_SFC			479
+
+#define CLK_NR_CLKS			(HCLK_SFC + 1)
+
+/* reset id */
+#define SRST_CORE_PO_AD			0
+#define SRST_CORE_AD			1
+#define SRST_L2_AD			2
+#define SRST_CPU_NIU_AD			3
+#define SRST_CORE_PO			4
+#define SRST_CORE			5
+#define SRST_L2				6
+#define SRST_CORE_DBG			8
+#define PRST_DBG			9
+#define RST_DAP				10
+#define PRST_DBG_NIU			11
+#define ARST_STRC_SYS_AD		15
+
+#define SRST_DDRPHY_CLKDIV		16
+#define SRST_DDRPHY			17
+#define PRST_DDRPHY			18
+#define PRST_HDMIPHY			19
+#define PRST_VDACPHY			20
+#define PRST_VADCPHY			21
+#define PRST_MIPI_CSI_PHY		22
+#define PRST_MIPI_DSI_PHY		23
+#define PRST_ACODEC			24
+#define ARST_BUS_NIU			25
+#define PRST_TOP_NIU			26
+#define ARST_INTMEM			27
+#define HRST_ROM			28
+#define ARST_DMAC			29
+#define SRST_MSCH_NIU			30
+#define PRST_MSCH_NIU			31
+
+#define PRST_DDRUPCTL			32
+#define NRST_DDRUPCTL			33
+#define PRST_DDRMON			34
+#define HRST_I2S0_8CH			35
+#define MRST_I2S0_8CH			36
+#define HRST_I2S1_2CH			37
+#define MRST_IS21_2CH			38
+#define HRST_I2S2_2CH			39
+#define MRST_I2S2_2CH			40
+#define HRST_CRYPTO			41
+#define SRST_CRYPTO			42
+#define PRST_SPI			43
+#define SRST_SPI			44
+#define PRST_UART0			45
+#define PRST_UART1			46
+#define PRST_UART2			47
+
+#define SRST_UART0			48
+#define SRST_UART1			49
+#define SRST_UART2			50
+#define PRST_I2C1			51
+#define PRST_I2C2			52
+#define PRST_I2C3			53
+#define SRST_I2C1			54
+#define SRST_I2C2			55
+#define SRST_I2C3			56
+#define PRST_PWM1			58
+#define SRST_PWM1			60
+#define PRST_WDT			61
+#define PRST_GPIO1			62
+#define PRST_GPIO2			63
+
+#define PRST_GPIO3			64
+#define PRST_GRF			65
+#define PRST_EFUSE			66
+#define PRST_EFUSE512			67
+#define PRST_TIMER0			68
+#define SRST_TIMER0			69
+#define SRST_TIMER1			70
+#define PRST_TSADC			71
+#define SRST_TSADC			72
+#define PRST_SARADC			73
+#define SRST_SARADC			74
+#define HRST_SYSBUS			75
+#define PRST_USBGRF			76
+
+#define ARST_PERIPH_NIU			80
+#define HRST_PERIPH_NIU			81
+#define PRST_PERIPH_NIU			82
+#define HRST_PERIPH			83
+#define HRST_SDMMC			84
+#define HRST_SDIO			85
+#define HRST_EMMC			86
+#define HRST_NANDC			87
+#define NRST_NANDC			88
+#define HRST_SFC			89
+#define SRST_SFC			90
+#define ARST_GMAC			91
+#define HRST_OTG			92
+#define SRST_OTG			93
+#define SRST_OTG_ADP			94
+#define HRST_HOST0			95
+
+#define HRST_HOST0_AUX			96
+#define HRST_HOST0_ARB			97
+#define SRST_HOST0_EHCIPHY		98
+#define SRST_HOST0_UTMI			99
+#define SRST_USBPOR			100
+#define SRST_UTMI0			101
+#define SRST_UTMI1			102
+
+#define ARST_VIO0_NIU			102
+#define ARST_VIO1_NIU			103
+#define HRST_VIO_NIU			104
+#define PRST_VIO_NIU			105
+#define ARST_VOP			106
+#define HRST_VOP			107
+#define DRST_VOP			108
+#define ARST_IEP			109
+#define HRST_IEP			110
+#define ARST_RGA			111
+#define HRST_RGA			112
+#define SRST_RGA			113
+#define PRST_CVBS			114
+#define PRST_HDMI			115
+#define SRST_HDMI			116
+#define PRST_MIPI_DSI			117
+
+#define ARST_ISP_NIU			118
+#define HRST_ISP_NIU			119
+#define HRST_ISP			120
+#define SRST_ISP			121
+#define ARST_VIP0			122
+#define HRST_VIP0			123
+#define PRST_VIP0			124
+#define ARST_VIP1			125
+#define HRST_VIP1			126
+#define PRST_VIP1			127
+#define ARST_VIP2			128
+#define HRST_VIP2			129
+#define PRST_VIP2			120
+#define ARST_VIP3			121
+#define HRST_VIP3			122
+#define PRST_VIP4			123
+
+#define PRST_CIF1TO4			124
+#define SRST_CVBS_CLK			125
+#define HRST_CVBS			126
+
+#define ARST_VPU_NIU			140
+#define HRST_VPU_NIU			141
+#define ARST_VPU			142
+#define HRST_VPU			143
+#define ARST_RKVDEC_NIU			144
+#define HRST_RKVDEC_NIU			145
+#define ARST_RKVDEC			146
+#define HRST_RKVDEC			147
+#define SRST_RKVDEC_CABAC		148
+#define SRST_RKVDEC_CORE		149
+#define ARST_RKVENC_NIU			150
+#define HRST_RKVENC_NIU			151
+#define ARST_RKVENC			152
+#define HRST_RKVENC			153
+#define SRST_RKVENC_CORE		154
+
+#define SRST_DSP_CORE			156
+#define SRST_DSP_SYS			157
+#define SRST_DSP_GLOBAL			158
+#define SRST_DSP_OECM			159
+#define PRST_DSP_IOP_NIU		160
+#define ARST_DSP_EPP_NIU		161
+#define ARST_DSP_EDP_NIU		162
+#define PRST_DSP_DBG_NIU		163
+#define PRST_DSP_CFG_NIU		164
+#define PRST_DSP_GRF			165
+#define PRST_DSP_MAILBOX		166
+#define PRST_DSP_INTC			167
+#define PRST_DSP_PFM_MON		169
+#define SRST_DSP_PFM_MON		170
+#define ARST_DSP_EDAP_NIU		171
+
+#define SRST_PMU			172
+#define SRST_PMU_I2C0			173
+#define PRST_PMU_I2C0			174
+#define PRST_PMU_GPIO0			175
+#define PRST_PMU_INTMEM			176
+#define PRST_PMU_PWM0			177
+#define SRST_PMU_PWM0			178
+#define PRST_PMU_GRF			179
+#define SRST_PMU_NIU			180
+#define SRST_PMU_PVTM			181
+#define ARST_DSP_EDP_PERF		184
+#define ARST_DSP_EPP_PERF		185
+
+#endif /* _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H */
+
-- 
2.7.4

Re: [PATCH v2 03/10] clk: rockchip: add dt-binding header for rk1108

[Heiko Stuebner]

Am Montag, 14. November 2016, 20:04:52 CET schrieb Andy Yan:
> From: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> 
> Add the dt-bindings header for the rk1108, that gets shared
> between the clock controller and the clock references in the dts.
> 
> Signed-off-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> ---
> 
> Changes in v2:
> - split dt-binding header from clk driver
> 
>  include/dt-bindings/clock/rk1108-cru.h | 270
> +++++++++++++++++++++++++++++++++ 1 file changed, 270 insertions(+)
>  create mode 100644 include/dt-bindings/clock/rk1108-cru.h
> 
> diff --git a/include/dt-bindings/clock/rk1108-cru.h
> b/include/dt-bindings/clock/rk1108-cru.h new file mode 100644
> index 0000000..6f30008
> --- /dev/null
> +++ b/include/dt-bindings/clock/rk1108-cru.h
> @@ -0,0 +1,270 @@
> +/*
> + * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
> + * Author: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
> +#define _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
> +
> +/* pll id */
> +#define RK1108_APLL_ID			0
> +#define RK1108_DPLL_ID			1
> +#define RK1108_GPLL_ID			2
> +#define RK1108_ARMCLK			3

any particular reason for diverging from namings set in the other binding 
headers (PLL_APLL, ARMCLK, ...)?


> +
> +/* sclk gates (special clocks) */
> +#define SCLK_SPI0			65
> +#define SCLK_NANDC			67
> +#define SCLK_SDMMC			68
> +#define SCLK_SDIO			69
> +#define SCLK_EMMC			71
> +#define SCLK_UART0			72
> +#define SCLK_UART1			73
> +#define SCLK_UART2			74
> +#define SCLK_I2S0			75
> +#define SCLK_I2S1			76
> +#define SCLK_I2S2			77
> +#define SCLK_TIMER0			78
> +#define SCLK_TIMER1			79
> +#define SCLK_SFC			80
> +#define SCLK_SDMMC_DRV			81
> +#define SCLK_SDIO_DRV			82
> +#define SCLK_EMMC_DRV			83
> +#define SCLK_SDMMC_SAMPLE		84
> +#define SCLK_SDIO_SAMPLE		85
> +#define SCLK_EMMC_SAMPLE		86

the rk1108 seems to have a pretty small clock tree, so maybe you can reduce 
the gap here a bit, like starting at 128 or 192 for the ACLKs and move 
everything up a bit?

That way you save a bit of space, as we're allocation CLK_NR_CLKS entries or 
the lookup array when probing the clock driver.


Heiko

> +/* aclk gates */
> +#define ACLK_DMAC			251
> +#define ACLK_PRE			252
> +#define ACLK_CORE			253
> +#define ACLK_ENMCORE			254
> +
> +/* pclk gates */
> +#define PCLK_GPIO1			321
> +#define PCLK_GPIO2			322
> +#define PCLK_GPIO3			323
> +#define PCLK_GRF			329
> +#define PCLK_I2C1			333
> +#define PCLK_I2C2			334
> +#define PCLK_I2C3			335
> +#define PCLK_SPI			338
> +#define PCLK_SFC			339
> +#define PCLK_UART0			341
> +#define PCLK_UART1			342
> +#define PCLK_UART2			343
> +#define PCLK_TSADC			344
> +#define PCLK_PWM			350
> +#define PCLK_TIMER			353
> +#define PCLK_PERI			363
> +
> +/* hclk gates */
> +#define HCLK_I2S0_8CH			442
> +#define HCLK_I2S1_8CH			443
> +#define HCLK_I2S2_2CH			444
> +#define HCLK_NANDC			453
> +#define HCLK_SDMMC			456
> +#define HCLK_SDIO			457
> +#define HCLK_EMMC			459
> +#define HCLK_PERI			478
> +#define HCLK_SFC			479
> +
> +#define CLK_NR_CLKS			(HCLK_SFC + 1)
> +
> +/* reset id */
> +#define SRST_CORE_PO_AD			0
> +#define SRST_CORE_AD			1
> +#define SRST_L2_AD			2
> +#define SRST_CPU_NIU_AD			3
> +#define SRST_CORE_PO			4
> +#define SRST_CORE			5
> +#define SRST_L2				6
> +#define SRST_CORE_DBG			8
> +#define PRST_DBG			9
> +#define RST_DAP				10
> +#define PRST_DBG_NIU			11
> +#define ARST_STRC_SYS_AD		15
> +
> +#define SRST_DDRPHY_CLKDIV		16
> +#define SRST_DDRPHY			17
> +#define PRST_DDRPHY			18
> +#define PRST_HDMIPHY			19
> +#define PRST_VDACPHY			20
> +#define PRST_VADCPHY			21
> +#define PRST_MIPI_CSI_PHY		22
> +#define PRST_MIPI_DSI_PHY		23
> +#define PRST_ACODEC			24
> +#define ARST_BUS_NIU			25
> +#define PRST_TOP_NIU			26
> +#define ARST_INTMEM			27
> +#define HRST_ROM			28
> +#define ARST_DMAC			29
> +#define SRST_MSCH_NIU			30
> +#define PRST_MSCH_NIU			31
> +
> +#define PRST_DDRUPCTL			32
> +#define NRST_DDRUPCTL			33
> +#define PRST_DDRMON			34
> +#define HRST_I2S0_8CH			35
> +#define MRST_I2S0_8CH			36
> +#define HRST_I2S1_2CH			37
> +#define MRST_IS21_2CH			38
> +#define HRST_I2S2_2CH			39
> +#define MRST_I2S2_2CH			40
> +#define HRST_CRYPTO			41
> +#define SRST_CRYPTO			42
> +#define PRST_SPI			43
> +#define SRST_SPI			44
> +#define PRST_UART0			45
> +#define PRST_UART1			46
> +#define PRST_UART2			47
> +
> +#define SRST_UART0			48
> +#define SRST_UART1			49
> +#define SRST_UART2			50
> +#define PRST_I2C1			51
> +#define PRST_I2C2			52
> +#define PRST_I2C3			53
> +#define SRST_I2C1			54
> +#define SRST_I2C2			55
> +#define SRST_I2C3			56
> +#define PRST_PWM1			58
> +#define SRST_PWM1			60
> +#define PRST_WDT			61
> +#define PRST_GPIO1			62
> +#define PRST_GPIO2			63
> +
> +#define PRST_GPIO3			64
> +#define PRST_GRF			65
> +#define PRST_EFUSE			66
> +#define PRST_EFUSE512			67
> +#define PRST_TIMER0			68
> +#define SRST_TIMER0			69
> +#define SRST_TIMER1			70
> +#define PRST_TSADC			71
> +#define SRST_TSADC			72
> +#define PRST_SARADC			73
> +#define SRST_SARADC			74
> +#define HRST_SYSBUS			75
> +#define PRST_USBGRF			76
> +
> +#define ARST_PERIPH_NIU			80
> +#define HRST_PERIPH_NIU			81
> +#define PRST_PERIPH_NIU			82
> +#define HRST_PERIPH			83
> +#define HRST_SDMMC			84
> +#define HRST_SDIO			85
> +#define HRST_EMMC			86
> +#define HRST_NANDC			87
> +#define NRST_NANDC			88
> +#define HRST_SFC			89
> +#define SRST_SFC			90
> +#define ARST_GMAC			91
> +#define HRST_OTG			92
> +#define SRST_OTG			93
> +#define SRST_OTG_ADP			94
> +#define HRST_HOST0			95
> +
> +#define HRST_HOST0_AUX			96
> +#define HRST_HOST0_ARB			97
> +#define SRST_HOST0_EHCIPHY		98
> +#define SRST_HOST0_UTMI			99
> +#define SRST_USBPOR			100
> +#define SRST_UTMI0			101
> +#define SRST_UTMI1			102
> +
> +#define ARST_VIO0_NIU			102
> +#define ARST_VIO1_NIU			103
> +#define HRST_VIO_NIU			104
> +#define PRST_VIO_NIU			105
> +#define ARST_VOP			106
> +#define HRST_VOP			107
> +#define DRST_VOP			108
> +#define ARST_IEP			109
> +#define HRST_IEP			110
> +#define ARST_RGA			111
> +#define HRST_RGA			112
> +#define SRST_RGA			113
> +#define PRST_CVBS			114
> +#define PRST_HDMI			115
> +#define SRST_HDMI			116
> +#define PRST_MIPI_DSI			117
> +
> +#define ARST_ISP_NIU			118
> +#define HRST_ISP_NIU			119
> +#define HRST_ISP			120
> +#define SRST_ISP			121
> +#define ARST_VIP0			122
> +#define HRST_VIP0			123
> +#define PRST_VIP0			124
> +#define ARST_VIP1			125
> +#define HRST_VIP1			126
> +#define PRST_VIP1			127
> +#define ARST_VIP2			128
> +#define HRST_VIP2			129
> +#define PRST_VIP2			120
> +#define ARST_VIP3			121
> +#define HRST_VIP3			122
> +#define PRST_VIP4			123
> +
> +#define PRST_CIF1TO4			124
> +#define SRST_CVBS_CLK			125
> +#define HRST_CVBS			126
> +
> +#define ARST_VPU_NIU			140
> +#define HRST_VPU_NIU			141
> +#define ARST_VPU			142
> +#define HRST_VPU			143
> +#define ARST_RKVDEC_NIU			144
> +#define HRST_RKVDEC_NIU			145
> +#define ARST_RKVDEC			146
> +#define HRST_RKVDEC			147
> +#define SRST_RKVDEC_CABAC		148
> +#define SRST_RKVDEC_CORE		149
> +#define ARST_RKVENC_NIU			150
> +#define HRST_RKVENC_NIU			151
> +#define ARST_RKVENC			152
> +#define HRST_RKVENC			153
> +#define SRST_RKVENC_CORE		154
> +
> +#define SRST_DSP_CORE			156
> +#define SRST_DSP_SYS			157
> +#define SRST_DSP_GLOBAL			158
> +#define SRST_DSP_OECM			159
> +#define PRST_DSP_IOP_NIU		160
> +#define ARST_DSP_EPP_NIU		161
> +#define ARST_DSP_EDP_NIU		162
> +#define PRST_DSP_DBG_NIU		163
> +#define PRST_DSP_CFG_NIU		164
> +#define PRST_DSP_GRF			165
> +#define PRST_DSP_MAILBOX		166
> +#define PRST_DSP_INTC			167
> +#define PRST_DSP_PFM_MON		169
> +#define SRST_DSP_PFM_MON		170
> +#define ARST_DSP_EDAP_NIU		171
> +
> +#define SRST_PMU			172
> +#define SRST_PMU_I2C0			173
> +#define PRST_PMU_I2C0			174
> +#define PRST_PMU_GPIO0			175
> +#define PRST_PMU_INTMEM			176
> +#define PRST_PMU_PWM0			177
> +#define SRST_PMU_PWM0			178
> +#define PRST_PMU_GRF			179
> +#define SRST_PMU_NIU			180
> +#define SRST_PMU_PVTM			181
> +#define ARST_DSP_EDP_PERF		184
> +#define ARST_DSP_EPP_PERF		185
> +
> +#endif /* _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H */
> +

Re: [PATCH v2 03/10] clk: rockchip: add dt-binding header for rk1108

[Shawn Lin]

On 2016/11/15 17:41, Heiko Stuebner wrote:
> Am Montag, 14. November 2016, 20:04:52 CET schrieb Andy Yan:
>> From: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>>
>> Add the dt-bindings header for the rk1108, that gets shared
>> between the clock controller and the clock references in the dts.
>>
>> Signed-off-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>> Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>> ---
>>
>> Changes in v2:
>> - split dt-binding header from clk driver
>>
>>  include/dt-bindings/clock/rk1108-cru.h | 270
>> +++++++++++++++++++++++++++++++++ 1 file changed, 270 insertions(+)
>>  create mode 100644 include/dt-bindings/clock/rk1108-cru.h
>>
>> diff --git a/include/dt-bindings/clock/rk1108-cru.h
>> b/include/dt-bindings/clock/rk1108-cru.h new file mode 100644
>> index 0000000..6f30008
>> --- /dev/null
>> +++ b/include/dt-bindings/clock/rk1108-cru.h
>> @@ -0,0 +1,270 @@
>> +/*
>> + * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
>> + * Author: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#ifndef _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
>> +#define _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
>> +
>> +/* pll id */
>> +#define RK1108_APLL_ID			0
>> +#define RK1108_DPLL_ID			1
>> +#define RK1108_GPLL_ID			2
>> +#define RK1108_ARMCLK			3
>
> any particular reason for diverging from namings set in the other binding
> headers (PLL_APLL, ARMCLK, ...)?
>

nope, will make it consistent with others. :)

>
>> +
>> +/* sclk gates (special clocks) */
>> +#define SCLK_SPI0			65
>> +#define SCLK_NANDC			67
>> +#define SCLK_SDMMC			68
>> +#define SCLK_SDIO			69
>> +#define SCLK_EMMC			71
>> +#define SCLK_UART0			72
>> +#define SCLK_UART1			73
>> +#define SCLK_UART2			74
>> +#define SCLK_I2S0			75
>> +#define SCLK_I2S1			76
>> +#define SCLK_I2S2			77
>> +#define SCLK_TIMER0			78
>> +#define SCLK_TIMER1			79
>> +#define SCLK_SFC			80
>> +#define SCLK_SDMMC_DRV			81
>> +#define SCLK_SDIO_DRV			82
>> +#define SCLK_EMMC_DRV			83
>> +#define SCLK_SDMMC_SAMPLE		84
>> +#define SCLK_SDIO_SAMPLE		85
>> +#define SCLK_EMMC_SAMPLE		86
>
> the rk1108 seems to have a pretty small clock tree, so maybe you can reduce
> the gap here a bit, like starting at 128 or 192 for the ACLKs and move
> everything up a bit?
>

okay.

> That way you save a bit of space, as we're allocation CLK_NR_CLKS entries or
> the lookup array when probing the clock driver.
>
>
> Heiko
>
>> +/* aclk gates */
>> +#define ACLK_DMAC			251
>> +#define ACLK_PRE			252
>> +#define ACLK_CORE			253
>> +#define ACLK_ENMCORE			254
>> +
>> +/* pclk gates */
>> +#define PCLK_GPIO1			321
>> +#define PCLK_GPIO2			322
>> +#define PCLK_GPIO3			323
>> +#define PCLK_GRF			329
>> +#define PCLK_I2C1			333
>> +#define PCLK_I2C2			334
>> +#define PCLK_I2C3			335
>> +#define PCLK_SPI			338
>> +#define PCLK_SFC			339
>> +#define PCLK_UART0			341
>> +#define PCLK_UART1			342
>> +#define PCLK_UART2			343
>> +#define PCLK_TSADC			344
>> +#define PCLK_PWM			350
>> +#define PCLK_TIMER			353
>> +#define PCLK_PERI			363
>> +
>> +/* hclk gates */
>> +#define HCLK_I2S0_8CH			442
>> +#define HCLK_I2S1_8CH			443
>> +#define HCLK_I2S2_2CH			444
>> +#define HCLK_NANDC			453
>> +#define HCLK_SDMMC			456
>> +#define HCLK_SDIO			457
>> +#define HCLK_EMMC			459
>> +#define HCLK_PERI			478
>> +#define HCLK_SFC			479
>> +
>> +#define CLK_NR_CLKS			(HCLK_SFC + 1)
>> +
>> +/* reset id */
>> +#define SRST_CORE_PO_AD			0
>> +#define SRST_CORE_AD			1
>> +#define SRST_L2_AD			2
>> +#define SRST_CPU_NIU_AD			3
>> +#define SRST_CORE_PO			4
>> +#define SRST_CORE			5
>> +#define SRST_L2				6
>> +#define SRST_CORE_DBG			8
>> +#define PRST_DBG			9
>> +#define RST_DAP				10
>> +#define PRST_DBG_NIU			11
>> +#define ARST_STRC_SYS_AD		15
>> +
>> +#define SRST_DDRPHY_CLKDIV		16
>> +#define SRST_DDRPHY			17
>> +#define PRST_DDRPHY			18
>> +#define PRST_HDMIPHY			19
>> +#define PRST_VDACPHY			20
>> +#define PRST_VADCPHY			21
>> +#define PRST_MIPI_CSI_PHY		22
>> +#define PRST_MIPI_DSI_PHY		23
>> +#define PRST_ACODEC			24
>> +#define ARST_BUS_NIU			25
>> +#define PRST_TOP_NIU			26
>> +#define ARST_INTMEM			27
>> +#define HRST_ROM			28
>> +#define ARST_DMAC			29
>> +#define SRST_MSCH_NIU			30
>> +#define PRST_MSCH_NIU			31
>> +
>> +#define PRST_DDRUPCTL			32
>> +#define NRST_DDRUPCTL			33
>> +#define PRST_DDRMON			34
>> +#define HRST_I2S0_8CH			35
>> +#define MRST_I2S0_8CH			36
>> +#define HRST_I2S1_2CH			37
>> +#define MRST_IS21_2CH			38
>> +#define HRST_I2S2_2CH			39
>> +#define MRST_I2S2_2CH			40
>> +#define HRST_CRYPTO			41
>> +#define SRST_CRYPTO			42
>> +#define PRST_SPI			43
>> +#define SRST_SPI			44
>> +#define PRST_UART0			45
>> +#define PRST_UART1			46
>> +#define PRST_UART2			47
>> +
>> +#define SRST_UART0			48
>> +#define SRST_UART1			49
>> +#define SRST_UART2			50
>> +#define PRST_I2C1			51
>> +#define PRST_I2C2			52
>> +#define PRST_I2C3			53
>> +#define SRST_I2C1			54
>> +#define SRST_I2C2			55
>> +#define SRST_I2C3			56
>> +#define PRST_PWM1			58
>> +#define SRST_PWM1			60
>> +#define PRST_WDT			61
>> +#define PRST_GPIO1			62
>> +#define PRST_GPIO2			63
>> +
>> +#define PRST_GPIO3			64
>> +#define PRST_GRF			65
>> +#define PRST_EFUSE			66
>> +#define PRST_EFUSE512			67
>> +#define PRST_TIMER0			68
>> +#define SRST_TIMER0			69
>> +#define SRST_TIMER1			70
>> +#define PRST_TSADC			71
>> +#define SRST_TSADC			72
>> +#define PRST_SARADC			73
>> +#define SRST_SARADC			74
>> +#define HRST_SYSBUS			75
>> +#define PRST_USBGRF			76
>> +
>> +#define ARST_PERIPH_NIU			80
>> +#define HRST_PERIPH_NIU			81
>> +#define PRST_PERIPH_NIU			82
>> +#define HRST_PERIPH			83
>> +#define HRST_SDMMC			84
>> +#define HRST_SDIO			85
>> +#define HRST_EMMC			86
>> +#define HRST_NANDC			87
>> +#define NRST_NANDC			88
>> +#define HRST_SFC			89
>> +#define SRST_SFC			90
>> +#define ARST_GMAC			91
>> +#define HRST_OTG			92
>> +#define SRST_OTG			93
>> +#define SRST_OTG_ADP			94
>> +#define HRST_HOST0			95
>> +
>> +#define HRST_HOST0_AUX			96
>> +#define HRST_HOST0_ARB			97
>> +#define SRST_HOST0_EHCIPHY		98
>> +#define SRST_HOST0_UTMI			99
>> +#define SRST_USBPOR			100
>> +#define SRST_UTMI0			101
>> +#define SRST_UTMI1			102
>> +
>> +#define ARST_VIO0_NIU			102
>> +#define ARST_VIO1_NIU			103
>> +#define HRST_VIO_NIU			104
>> +#define PRST_VIO_NIU			105
>> +#define ARST_VOP			106
>> +#define HRST_VOP			107
>> +#define DRST_VOP			108
>> +#define ARST_IEP			109
>> +#define HRST_IEP			110
>> +#define ARST_RGA			111
>> +#define HRST_RGA			112
>> +#define SRST_RGA			113
>> +#define PRST_CVBS			114
>> +#define PRST_HDMI			115
>> +#define SRST_HDMI			116
>> +#define PRST_MIPI_DSI			117
>> +
>> +#define ARST_ISP_NIU			118
>> +#define HRST_ISP_NIU			119
>> +#define HRST_ISP			120
>> +#define SRST_ISP			121
>> +#define ARST_VIP0			122
>> +#define HRST_VIP0			123
>> +#define PRST_VIP0			124
>> +#define ARST_VIP1			125
>> +#define HRST_VIP1			126
>> +#define PRST_VIP1			127
>> +#define ARST_VIP2			128
>> +#define HRST_VIP2			129
>> +#define PRST_VIP2			120
>> +#define ARST_VIP3			121
>> +#define HRST_VIP3			122
>> +#define PRST_VIP4			123
>> +
>> +#define PRST_CIF1TO4			124
>> +#define SRST_CVBS_CLK			125
>> +#define HRST_CVBS			126
>> +
>> +#define ARST_VPU_NIU			140
>> +#define HRST_VPU_NIU			141
>> +#define ARST_VPU			142
>> +#define HRST_VPU			143
>> +#define ARST_RKVDEC_NIU			144
>> +#define HRST_RKVDEC_NIU			145
>> +#define ARST_RKVDEC			146
>> +#define HRST_RKVDEC			147
>> +#define SRST_RKVDEC_CABAC		148
>> +#define SRST_RKVDEC_CORE		149
>> +#define ARST_RKVENC_NIU			150
>> +#define HRST_RKVENC_NIU			151
>> +#define ARST_RKVENC			152
>> +#define HRST_RKVENC			153
>> +#define SRST_RKVENC_CORE		154
>> +
>> +#define SRST_DSP_CORE			156
>> +#define SRST_DSP_SYS			157
>> +#define SRST_DSP_GLOBAL			158
>> +#define SRST_DSP_OECM			159
>> +#define PRST_DSP_IOP_NIU		160
>> +#define ARST_DSP_EPP_NIU		161
>> +#define ARST_DSP_EDP_NIU		162
>> +#define PRST_DSP_DBG_NIU		163
>> +#define PRST_DSP_CFG_NIU		164
>> +#define PRST_DSP_GRF			165
>> +#define PRST_DSP_MAILBOX		166
>> +#define PRST_DSP_INTC			167
>> +#define PRST_DSP_PFM_MON		169
>> +#define SRST_DSP_PFM_MON		170
>> +#define ARST_DSP_EDAP_NIU		171
>> +
>> +#define SRST_PMU			172
>> +#define SRST_PMU_I2C0			173
>> +#define PRST_PMU_I2C0			174
>> +#define PRST_PMU_GPIO0			175
>> +#define PRST_PMU_INTMEM			176
>> +#define PRST_PMU_PWM0			177
>> +#define SRST_PMU_PWM0			178
>> +#define PRST_PMU_GRF			179
>> +#define SRST_PMU_NIU			180
>> +#define SRST_PMU_PVTM			181
>> +#define ARST_DSP_EDP_PERF		184
>> +#define ARST_DSP_EPP_PERF		185
>> +
>> +#endif /* _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H */
>> +
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>


-- 
Best Regards
Shawn Lin

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 08/10] ARM: dts: add basic support for Rockchip RK1108 SOC

[Andy Yan]

RK1108 is embedded with an ARM Cortex-A7 single core and a DSP core.
It is designed for varies application scenario such as car DVR, sports
DV, secure camera and UAV camera.

This patch add basic support for it with DMAC / UART / CRU / pinctrl / MMC
enabled.

Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Tested-by: Jacob Chen <jacob2.chen-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

---

Changes in v2:
- fix timer and gic dt description
- ordering devices by register address

 arch/arm/boot/dts/rk1108.dtsi | 428 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 428 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk1108.dtsi

diff --git a/arch/arm/boot/dts/rk1108.dtsi b/arch/arm/boot/dts/rk1108.dtsi
new file mode 100644
index 0000000..636c294
--- /dev/null
+++ b/arch/arm/boot/dts/rk1108.dtsi
@@ -0,0 +1,428 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/rk1108-cru.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	compatible = "rockchip,rk1108";
+
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@f00 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+		clock-frequency = <24000000>;
+	};
+
+	xin24m: oscillator {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xin24m";
+		#clock-cells = <0>;
+	};
+
+	bus_intmem@10080000 {
+		compatible = "mmio-sram";
+		reg = <0x10080000 0x2000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x10080000 0x2000>;
+	};
+
+	amba {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		pdma: pdma@102a0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x102a0000 0x4000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			arm,pl330-broken-no-flushp;
+			clocks = <&cru ACLK_DMAC>;
+			clock-names = "apb_pclk";
+		};
+	};
+
+	uart2: serial@10210000 {
+		compatible = "rockchip,rk1108-uart", "snps,dw-apb-uart";
+		reg = <0x10210000 0x100>;
+		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+		clock-names = "baudclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2m0_xfer>;
+		status = "disabled";
+	};
+
+	uart1: serial@10220000 {
+		compatible = "rockchip,rk1108-uart", "snps,dw-apb-uart";
+		reg = <0x10220000 0x100>;
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+		clock-names = "baudclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1_xfer>;
+		status = "disabled";
+	};
+
+	uart0: serial@10230000 {
+		compatible = "rockchip,rk1108-uart", "snps,dw-apb-uart";
+		reg = <0x10230000 0x100>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+		clock-names = "baudclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+		status = "disabled";
+	};
+
+	grf: syscon@10300000 {
+		compatible = "rockchip,rk1108-grf", "syscon";
+		reg = <0x10300000 0x1000>;
+	};
+
+	pmugrf: syscon@20060000 {
+		compatible = "rockchip,rk1108-pmugrf", "syscon";
+		reg = <0x20060000 0x1000>;
+	};
+
+	cru: clock-controller@20200000 {
+		compatible = "rockchip,rk1108-cru";
+		reg = <0x20200000 0x1000>;
+		rockchip,grf = <&grf>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+	emmc: dwmmc@30110000 {
+		compatible = "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc";
+		clock-freq-min-max = <400000 150000000>;
+		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x30110000 0x4000>;
+		status = "disabled";
+	};
+
+	sdio: dwmmc@30120000 {
+		compatible = "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc";
+		clock-freq-min-max = <400000 150000000>;
+		clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
+			 <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x30120000 0x4000>;
+		status = "disabled";
+	};
+
+	sdmmc: dwmmc@30130000 {
+		compatible = "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc";
+		clock-freq-min-max = <400000 100000000>;
+		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+			 <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x30130000 0x4000>;
+		status = "disabled";
+	};
+
+	gic: interrupt-controller@32010000 {
+		compatible = "arm,gic-400";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+
+		reg = <0x32011000 0x1000>,
+		      <0x32012000 0x1000>,
+		      <0x32014000 0x2000>,
+		      <0x32016000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	pinctrl: pinctrl {
+		compatible = "rockchip,rk1108-pinctrl";
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmugrf>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio0@20030000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x20030000 0x100>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&xin24m>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio1@10310000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x10310000 0x100>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&xin24m>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio2@10320000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x10320000 0x100>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&xin24m>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio3@10330000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x10330000 0x100>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&xin24m>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pcfg_pull_up: pcfg-pull-up {
+			bias-pull-up;
+		};
+
+		pcfg_pull_down: pcfg-pull-down {
+			bias-pull-down;
+		};
+
+		pcfg_pull_none: pcfg-pull-none {
+			bias-disable;
+		};
+
+		pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+			drive-strength = <8>;
+		};
+
+		pcfg_pull_none_drv_12ma: pcfg-pull-none-drv-12ma {
+			drive-strength = <12>;
+		};
+
+		pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+			bias-pull-up;
+			drive-strength = <8>;
+		};
+
+		pcfg_pull_none_drv_4ma: pcfg-pull-none-drv-4ma {
+			drive-strength = <4>;
+		};
+
+		pcfg_pull_up_drv_4ma: pcfg-pull-up-drv-4ma {
+			bias-pull-up;
+			drive-strength = <4>;
+		};
+
+		pcfg_output_high: pcfg-output-high {
+			output-high;
+		};
+
+		pcfg_output_low: pcfg-output-low {
+			output-low;
+		};
+
+		pcfg_input_high: pcfg-input-high {
+			bias-pull-up;
+			input-enable;
+		};
+
+		i2c1 {
+			i2c1_xfer: i2c1-xfer {
+				rockchip,pins = <2 RK_PD3 RK_FUNC_1 &pcfg_pull_up>,
+						<2 RK_PD4 RK_FUNC_1 &pcfg_pull_up>;
+			};
+		};
+
+		i2c2m1 {
+			i2c2m1_xfer: i2c2m1-xfer {
+				rockchip,pins = <0 RK_PC2 RK_FUNC_2 &pcfg_pull_none>,
+						<0 RK_PC6 RK_FUNC_3 &pcfg_pull_none>;
+			};
+
+			i2c2m1_gpio: i2c2m1-gpio {
+				rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,
+						<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+			};
+		};
+
+		i2c2m05v {
+			i2c2m05v_xfer: i2c2m05v-xfer {
+				rockchip,pins = <1 RK_PD5 RK_FUNC_2 &pcfg_pull_none>,
+						<1 RK_PD4 RK_FUNC_2 &pcfg_pull_none>;
+			};
+
+			i2c2m05v_gpio: i2c2m05v-gpio {
+				rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
+						<1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+			};
+		};
+
+		i2c3 {
+			i2c3_xfer: i2c3-xfer {
+				rockchip,pins = <0 RK_PB6 RK_FUNC_1 &pcfg_pull_none>,
+						<0 RK_PC4 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+
+		uart0 {
+			uart0_xfer: uart0-xfer {
+				rockchip,pins = <3 RK_PA6 RK_FUNC_1 &pcfg_pull_up>,
+						<3 RK_PA5 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart0_cts: uart0-cts {
+				rockchip,pins = <3 RK_PA4 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart0_rts: uart0-rts {
+				rockchip,pins = <3 RK_PA3 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart0_rts_gpio: uart0-rts-gpio {
+				rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+			};
+		};
+
+		uart1 {
+			uart1_xfer: uart1-xfer {
+				rockchip,pins = <1 RK_PD3 RK_FUNC_1 &pcfg_pull_up>,
+						<1 RK_PD2 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart1_cts: uart1-cts {
+				rockchip,pins = <1 RK_PD0 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart1_rts: uart1-rts {
+				rockchip,pins = <1 RK_PD1 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		uart2m0 {
+			uart2m0_xfer: uart2m0-xfer {
+				rockchip,pins = <2 RK_PD2 RK_FUNC_1 &pcfg_pull_up>,
+						<2 RK_PD1 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+
+		uart2m1 {
+			uart2m1_xfer: uart2m1-xfer {
+				rockchip,pins = <3 RK_PC3 RK_FUNC_2 &pcfg_pull_up>,
+						<3 RK_PC2 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+
+		uart2_5v {
+			uart2_5v_cts: uart2_5v-cts {
+				rockchip,pins = <1 RK_PD4 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			uart2_5v_rts: uart2_5v-rts {
+				rockchip,pins = <1 RK_PD5 RK_FUNC_1 &pcfg_pull_none>;
+			};
+		};
+	};
+};
-- 
2.7.4


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 08/10] ARM: dts: add basic support for Rockchip RK1108 SOC

[Heiko Stuebner]

Am Montag, 14. November 2016, 20:14:48 CET schrieb Andy Yan:
> RK1108 is embedded with an ARM Cortex-A7 single core and a DSP core.
> It is designed for varies application scenario such as car DVR, sports
> DV, secure camera and UAV camera.
> 
> This patch add basic support for it with DMAC / UART / CRU / pinctrl / MMC
> enabled.
> 
> Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> Tested-by: Jacob Chen <jacob2.chen-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> 
> ---
> 
> Changes in v2:
> - fix timer and gic dt description
> - ordering devices by register address
> 
>  arch/arm/boot/dts/rk1108.dtsi | 428
> ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 428
> insertions(+)
>  create mode 100644 arch/arm/boot/dts/rk1108.dtsi
> 
> diff --git a/arch/arm/boot/dts/rk1108.dtsi b/arch/arm/boot/dts/rk1108.dtsi
> new file mode 100644
> index 0000000..636c294
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk1108.dtsi
> @@ -0,0 +1,428 @@
> +/*
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/rk1108-cru.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +/ {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +	compatible = "rockchip,rk1108";
> +
> +	interrupt-parent = <&gic>;
> +
> +	aliases {
> +		serial0 = &uart0;
> +		serial1 = &uart1;
> +		serial2 = &uart2;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@f00 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0xf00>;
> +		};
> +	};
> +
> +	arm-pmu {
> +		compatible = "arm,cortex-a7-pmu";
> +		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +

unnecessary empty line (only 1 please)

otherwise looks fine now, just needs to wait for fixed clock ids now.


Heiko
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 08/10] ARM: dts: add basic support for Rockchip RK1108 SOC

[Heiko Stuebner]

Am Dienstag, 15. November 2016, 12:45:16 CET schrieb Heiko Stuebner:
> Am Montag, 14. November 2016, 20:14:48 CET schrieb Andy Yan:
> > RK1108 is embedded with an ARM Cortex-A7 single core and a DSP core.
> > It is designed for varies application scenario such as car DVR, sports
> > DV, secure camera and UAV camera.
> > 
> > This patch add basic support for it with DMAC / UART / CRU / pinctrl / MMC
> > enabled.
> > 
> > Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> > Tested-by: Jacob Chen <jacob2.chen-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> > 
> > ---
> > 
> > Changes in v2:
> > - fix timer and gic dt description
> > - ordering devices by register address
> > 
> >  arch/arm/boot/dts/rk1108.dtsi | 428
> > 
> > ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 428
> > insertions(+)
> > 
> >  create mode 100644 arch/arm/boot/dts/rk1108.dtsi
> > 
> > diff --git a/arch/arm/boot/dts/rk1108.dtsi b/arch/arm/boot/dts/rk1108.dtsi
> > new file mode 100644
> > index 0000000..636c294
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/rk1108.dtsi
> > @@ -0,0 +1,428 @@
> > +/*
> > + * This file is dual-licensed: you can use it either under the terms
> > + * of the GPL or the X11 license, at your option. Note that this dual
> > + * licensing only applies to this file, and not this project as a
> > + * whole.
> > + *
> > + *  a) This file is free software; you can redistribute it and/or
> > + *     modify it under the terms of the GNU General Public License as
> > + *     published by the Free Software Foundation; either version 2 of the
> > + *     License, or (at your option) any later version.
> > + *
> > + *     This file is distributed in the hope that it will be useful,
> > + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + *     GNU General Public License for more details.
> > + *
> > + * Or, alternatively,
> > + *
> > + *  b) Permission is hereby granted, free of charge, to any person
> > + *     obtaining a copy of this software and associated documentation
> > + *     files (the "Software"), to deal in the Software without
> > + *     restriction, including without limitation the rights to use,
> > + *     copy, modify, merge, publish, distribute, sublicense, and/or
> > + *     sell copies of the Software, and to permit persons to whom the
> > + *     Software is furnished to do so, subject to the following
> > + *     conditions:
> > + *
> > + *     The above copyright notice and this permission notice shall be
> > + *     included in all copies or substantial portions of the Software.
> > + *
> > + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > + *     OTHER DEALINGS IN THE SOFTWARE.
> > + */
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/clock/rk1108-cru.h>
> > +#include <dt-bindings/pinctrl/rockchip.h>
> > +/ {
> > +	#address-cells = <1>;
> > +	#size-cells = <1>;
> > +
> > +	compatible = "rockchip,rk1108";
> > +
> > +	interrupt-parent = <&gic>;
> > +
> > +	aliases {
> > +		serial0 = &uart0;
> > +		serial1 = &uart1;
> > +		serial2 = &uart2;
> > +	};
> > +
> > +	cpus {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		cpu0: cpu@f00 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a7";
> > +			reg = <0xf00>;
> > +		};
> > +	};
> > +
> > +	arm-pmu {
> > +		compatible = "arm,cortex-a7-pmu";
> > +		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
> > +	};
> > +
> > +
> 
> unnecessary empty line (only 1 please)
> 
> otherwise looks fine now, just needs to wait for fixed clock ids now.

after Shawn fixed the clocks, applied now to my dts32 branch with that line 
removed.


Thanks
Heiko

[PATCH v2 10/10] ARM: dts: rockchip: add rockchip RK1108 Evaluation board

[Andy Yan]

RK1108 EVB is designed by Rockchip for CVR field.
This patch add basic support for it, which can boot with
initramfs into shell.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>

---

Changes in v2:
- move the board in the rockchip.txt to the block of Rockchip boards

 Documentation/devicetree/bindings/arm/rockchip.txt |  5 +-
 arch/arm/boot/dts/Makefile                         |  1 +
 arch/arm/boot/dts/rk1108-evb.dts                   | 69 ++++++++++++++++++++++
 3 files changed, 74 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/rk1108-evb.dts

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 10b92b5..e658b62 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -1,6 +1,5 @@
 Rockchip platforms device tree bindings
 ---------------------------------------
-
 - Kylin RK3036 board:
     Required root node properties:
       - compatible = "rockchip,kylin-rk3036", "rockchip,rk3036";
@@ -111,6 +110,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368";
 
+- Rockchip RK1108 Evaluation board
+    Required root node properties:
+      - compatible = "rockchip,rk1108-evb", "rockchip,rk1108";
+
 - Rockchip RK3368 evb:
     Required root node properties:
       - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e49476a..249dca9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -635,6 +635,7 @@ dtb-$(CONFIG_ARCH_REALVIEW) += \
 	arm-realview-pba8.dtb \
 	arm-realview-pbx-a9.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
+	rk1108-evb.dtb \
 	rk3036-evb.dtb \
 	rk3036-kylin.dtb \
 	rk3066a-bqcurie2.dtb \
diff --git a/arch/arm/boot/dts/rk1108-evb.dts b/arch/arm/boot/dts/rk1108-evb.dts
new file mode 100644
index 0000000..3956cff
--- /dev/null
+++ b/arch/arm/boot/dts/rk1108-evb.dts
@@ -0,0 +1,69 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk1108.dtsi"
+
+/ {
+	model = "Rockchip RK1108 Evaluation board";
+	compatible = "rockchip,rk1108-evb", "rockchip,rk1108";
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x08000000>;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
-- 
2.7.4

Re: [PATCH v2 10/10] ARM: dts: rockchip: add rockchip RK1108 Evaluation board

[Heiko Stuebner]

Am Montag, 14. November 2016, 20:17:43 CET schrieb Andy Yan:
> RK1108 EVB is designed by Rockchip for CVR field.
> This patch add basic support for it, which can boot with
> initramfs into shell.
> 
> Signed-off-by: Andy Yan <andy.yan-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> 
> ---
> 
> Changes in v2:
> - move the board in the rockchip.txt to the block of Rockchip boards
> 
>  Documentation/devicetree/bindings/arm/rockchip.txt |  5 +-
>  arch/arm/boot/dts/Makefile                         |  1 +
>  arch/arm/boot/dts/rk1108-evb.dts                   | 69
> ++++++++++++++++++++++ 3 files changed, 74 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boot/dts/rk1108-evb.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt
> b/Documentation/devicetree/bindings/arm/rockchip.txt index 10b92b5..e658b62
> 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.txt
> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt
> @@ -1,6 +1,5 @@
>  Rockchip platforms device tree bindings
>  ---------------------------------------
> -
>  - Kylin RK3036 board:
>      Required root node properties:
>        - compatible = "rockchip,kylin-rk3036", "rockchip,rk3036";

dropped this unrelated change

> @@ -111,6 +110,10 @@ Rockchip platforms device tree bindings
>      Required root node properties:
>        - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368";
> 
> +- Rockchip RK1108 Evaluation board
> +    Required root node properties:
> +      - compatible = "rockchip,rk1108-evb", "rockchip,rk1108";
> +
>  - Rockchip RK3368 evb:
>      Required root node properties:
>        - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368";

binding moved to a separate patch and applied to my dts64 to prevent conflicts 
with px5 addition.

And the actual board dts of course applied to my dts32 branch.


Thanks
Heiko

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html