* [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
2021-09-21 10:38 [PATCH V9 0/8] Add QSPI and QUPv3 DT nodes for SC7280 SoC Rajesh Patil
@ 2021-09-21 10:39 ` Rajesh Patil
2021-09-21 18:17 ` Stephen Boyd
0 siblings, 1 reply; 5+ messages in thread
From: Rajesh Patil @ 2021-09-21 10:39 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rob Herring
Cc: linux-arm-msm, linux-kernel, devicetree, rnayak,
saiprakash.ranjan, msavaliy, skakit, sboyd, mka, dianders,
Roja Rani Yarubandi, Rajesh Patil
From: Roja Rani Yarubandi <rojay@codeaurora.org>
Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
Changes in V9:
- As per Stephen's comments,
1. Moved back qup_opp_table from /soc@0/geniqup@9c0000 to /
2. changed node names to "qup_spi0_cs_gpio: qup-spi0-cs-gpio" beacuse
node names should have dashes instead of underscores.
Changes in V8:
- As per Matthias' comments, Added back qup_spiN_cs_gpio nodes in all spi ports
Changes in V7:
- As per Matthias' comments
Configuring cs pin with gpio (qup_spiN_cs_gpio) definitions are removed.
- As per Stephen's comments
Added qup_opp_table under /soc@0/geniqup@9c0000
Changes in V6:
- As per Matthias' comments,
1. Changed convention "clocks" followed by "clock-names"
2. Moved qup_opp_table from /soc to /
arch/arm64/boot/dts/qcom/sc7280.dtsi | 724 ++++++++++++++++++++++++++++++++++-
1 file changed, 722 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 2fbcb0a..b65c5da 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -434,6 +434,25 @@
};
};
+ qup_opp_table: qup-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-128000000 {
+ opp-hz = /bits/ 64 <128000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
@@ -536,24 +555,425 @@
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x2000>;
- clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ clock-names = "m-ahb", "s-ahb";
#address-cells = <2>;
#size-cells = <2>;
ranges;
+ iommus = <&apps_smmu 0x123 0x0>;
status = "disabled";
+ i2c0: i2c@980000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00980000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c0_data_clk>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi0: spi@980000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00980000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart0: serial@980000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00980000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c1: i2c@984000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00984000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_data_clk>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi1: spi@984000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00984000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>, <&qup_spi1_cs_gpio>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart1: serial@984000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00984000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c2: i2c@988000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00988000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_data_clk>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi2: spi@988000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00988000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>, <&qup_spi2_cs_gpio>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart2: serial@988000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00988000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c3: i2c@98c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0098c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_data_clk>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi3: spi@98c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0098c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>, <&qup_spi3_cs_gpio>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart3: serial@98c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0098c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c4: i2c@990000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00990000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_data_clk>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi4: spi@990000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00990000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>, <&qup_spi4_cs_gpio>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart4: serial@990000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00990000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c5: i2c@994000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00994000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_data_clk>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi5: spi@994000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00994000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>, <&qup_spi5_cs_gpio>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
uart5: serial@994000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x00994000 0 0x4000>;
- clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
pinctrl-names = "default";
pinctrl-0 = <&qup_uart5_default>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
+
+ i2c6: i2c@998000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00998000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_data_clk>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi6: spi@998000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00998000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>, <&qup_spi6_cs_gpio>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart6: serial@998000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00998000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c7: i2c@99c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0099c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c7_data_clk>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi7: spi@99c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0099c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>, <&qup_spi7_cs_gpio>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart7: serial@99c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0099c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
};
cnoc2: interconnect@1500000 {
@@ -1574,11 +1994,311 @@
function = "qspi_data";
};
+ qup_i2c0_data_clk: qup-i2c0-data-clk {
+ pins = "gpio0", "gpio1";
+ function = "qup00";
+ };
+
+ qup_i2c1_data_clk: qup-i2c1-data-clk {
+ pins = "gpio4", "gpio5";
+ function = "qup01";
+ };
+
+ qup_i2c2_data_clk: qup-i2c2-data-clk {
+ pins = "gpio8", "gpio9";
+ function = "qup02";
+ };
+
+ qup_i2c3_data_clk: qup-i2c3-data-clk {
+ pins = "gpio12", "gpio13";
+ function = "qup03";
+ };
+
+ qup_i2c4_data_clk: qup-i2c4-data-clk {
+ pins = "gpio16", "gpio17";
+ function = "qup04";
+ };
+
+ qup_i2c5_data_clk: qup-i2c5-data-clk {
+ pins = "gpio20", "gpio21";
+ function = "qup05";
+ };
+
+ qup_i2c6_data_clk: qup-i2c6-data-clk {
+ pins = "gpio24", "gpio25";
+ function = "qup06";
+ };
+
+ qup_i2c7_data_clk: qup-i2c7-data-clk {
+ pins = "gpio28", "gpio29";
+ function = "qup07";
+ };
+
+ qup_spi0_data_clk: qup-spi0-data-clk {
+ pins = "gpio0", "gpio1", "gpio2";
+ function = "qup00";
+ };
+
+ qup_spi0_cs: qup-spi0-cs {
+ pins = "gpio3";
+ function = "qup00";
+ };
+
+ qup_spi0_cs_gpio: qup-spi0-cs-gpio {
+ pins = "gpio3";
+ function = "gpio";
+ };
+
+ qup_spi1_data_clk: qup-spi1-data-clk {
+ pins = "gpio4", "gpio5", "gpio6";
+ function = "qup01";
+ };
+
+ qup_spi1_cs: qup-spi1-cs {
+ pins = "gpio7";
+ function = "qup01";
+ };
+
+ qup_spi1_cs_gpio: qup-spi1-cs-gpio {
+ pins = "gpio7";
+ function = "gpio";
+ };
+
+ qup_spi2_data_clk: qup-spi2-data-clk {
+ pins = "gpio8", "gpio9", "gpio10";
+ function = "qup02";
+ };
+
+ qup_spi2_cs: qup-spi2-cs {
+ pins = "gpio11";
+ function = "qup02";
+ };
+
+ qup_spi2_cs_gpio: qup-spi2-cs-gpio {
+ pins = "gpio11";
+ function = "gpio";
+ };
+
+ qup_spi3_data_clk: qup-spi3-data-clk {
+ pins = "gpio12", "gpio13", "gpio14";
+ function = "qup03";
+ };
+
+ qup_spi3_cs: qup-spi3-cs {
+ pins = "gpio15";
+ function = "qup03";
+ };
+
+ qup_spi3_cs_gpio: qup-spi3-cs-gpio {
+ pins = "gpio15";
+ function = "gpio";
+ };
+
+ qup_spi4_data_clk: qup-spi4-data-clk {
+ pins = "gpio16", "gpio17", "gpio18";
+ function = "qup04";
+ };
+
+ qup_spi4_cs: qup-spi4-cs {
+ pins = "gpio19";
+ function = "qup04";
+ };
+
+ qup_spi4_cs_gpio: qup-spi4-cs-gpio {
+ pins = "gpio19";
+ function = "gpio";
+ };
+
+ qup_spi5_data_clk: qup-spi5-data-clk {
+ pins = "gpio20", "gpio21", "gpio22";
+ function = "qup05";
+ };
+
+ qup_spi5_cs: qup-spi5-cs {
+ pins = "gpio23";
+ function = "qup05";
+ };
+
+ qup_spi5_cs_gpio: qup-spi5-cs-gpio {
+ pins = "gpio23";
+ function = "gpio";
+ };
+
+ qup_spi6_data_clk: qup-spi6-data-clk {
+ pins = "gpio24", "gpio25", "gpio26";
+ function = "qup06";
+ };
+
+ qup_spi6_cs: qup-spi6-cs {
+ pins = "gpio27";
+ function = "qup06";
+ };
+
+ qup_spi6_cs_gpio: qup-spi6-cs-gpio {
+ pins = "gpio27";
+ function = "gpio";
+ };
+
+ qup_spi7_data_clk: qup-spi7-data-clk {
+ pins = "gpio28", "gpio29", "gpio30";
+ function = "qup07";
+ };
+
+ qup_spi7_cs: qup-spi7-cs {
+ pins = "gpio31";
+ function = "qup07";
+ };
+
+ qup_spi7_cs_gpio: qup-spi7-cs-gpio {
+ pins = "gpio31";
+ function = "gpio";
+ };
+
+ qup_uart0_cts: qup-uart0-cts {
+ pins = "gpio0";
+ function = "qup00";
+ };
+
+ qup_uart0_rts: qup-uart0-rts {
+ pins = "gpio1";
+ function = "qup00";
+ };
+
+ qup_uart0_tx: qup-uart0-tx {
+ pins = "gpio2";
+ function = "qup00";
+ };
+
+ qup_uart0_rx: qup-uart0-rx {
+ pins = "gpio3";
+ function = "qup00";
+ };
+
+ qup_uart1_cts: qup-uart1-cts {
+ pins = "gpio4";
+ function = "qup01";
+ };
+
+ qup_uart1_rts: qup-uart1-rts {
+ pins = "gpio5";
+ function = "qup01";
+ };
+
+ qup_uart1_tx: qup-uart1-tx {
+ pins = "gpio6";
+ function = "qup01";
+ };
+
+ qup_uart1_rx: qup-uart1-rx {
+ pins = "gpio7";
+ function = "qup01";
+ };
+
+ qup_uart2_cts: qup-uart2-cts {
+ pins = "gpio8";
+ function = "qup02";
+ };
+
+ qup_uart2_rts: qup-uart2-rts {
+ pins = "gpio9";
+ function = "qup02";
+ };
+
+ qup_uart2_tx: qup-uart2-tx {
+ pins = "gpio10";
+ function = "qup02";
+ };
+
+ qup_uart2_rx: qup-uart2-rx {
+ pins = "gpio11";
+ function = "qup02";
+ };
+
+ qup_uart3_cts: qup-uart3-cts {
+ pins = "gpio12";
+ function = "qup03";
+ };
+
+ qup_uart3_rts: qup-uart3-rts {
+ pins = "gpio13";
+ function = "qup03";
+ };
+
+ qup_uart3_tx: qup-uart3-tx {
+ pins = "gpio14";
+ function = "qup03";
+ };
+
+ qup_uart3_rx: qup-uart3-rx {
+ pins = "gpio15";
+ function = "qup03";
+ };
+
+ qup_uart4_cts: qup-uart4-cts {
+ pins = "gpio16";
+ function = "qup04";
+ };
+
+ qup_uart4_rts: qup-uart4-rts {
+ pins = "gpio17";
+ function = "qup04";
+ };
+
+ qup_uart4_tx: qup-uart4-tx {
+ pins = "gpio18";
+ function = "qup04";
+ };
+
+ qup_uart4_rx: qup-uart4-rx {
+ pins = "gpio19";
+ function = "qup04";
+ };
+
qup_uart5_default: qup-uart5-default {
pins = "gpio46", "gpio47";
function = "qup13";
};
+ qup_uart6_cts: qup-uart6-cts {
+ pins = "gpio24";
+ function = "qup06";
+ };
+
+ qup_uart6_rts: qup-uart6-rts {
+ pins = "gpio25";
+ function = "qup06";
+ };
+
+ qup_uart6_tx: qup-uart6-tx {
+ pins = "gpio26";
+ function = "qup06";
+ };
+
+ qup_uart6_rx: qup-uart6-rx {
+ pins = "gpio27";
+ function = "qup06";
+ };
+
+ qup_uart7_cts: qup-uart7-cts {
+ pins = "gpio28";
+ function = "qup07";
+ };
+
+ qup_uart7_rts: qup-uart7-rts {
+ pins = "gpio29";
+ function = "qup07";
+ };
+
+ qup_uart7_tx: qup-uart7-tx {
+ pins = "gpio30";
+ function = "qup07";
+ };
+
+ qup_uart7_rx: qup-uart7-rx {
+ pins = "gpio31";
+ function = "qup07";
+ };
+
sdc1_on: sdc1-on {
clk {
pins = "sdc1_clk";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
2021-09-21 10:39 ` [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes Rajesh Patil
@ 2021-09-21 18:17 ` Stephen Boyd
0 siblings, 0 replies; 5+ messages in thread
From: Stephen Boyd @ 2021-09-21 18:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Rajesh Patil, Rob Herring
Cc: linux-arm-msm, linux-kernel, devicetree, rnayak,
saiprakash.ranjan, msavaliy, skakit, mka, dianders,
Roja Rani Yarubandi
Quoting Rajesh Patil (2021-09-21 03:39:02)
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 2fbcb0a..b65c5da 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -536,24 +555,425 @@
> qupv3_id_0: geniqup@9c0000 {
> compatible = "qcom,geni-se-qup";
> reg = <0 0x009c0000 0 0x2000>;
> - clock-names = "m-ahb", "s-ahb";
> clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + clock-names = "m-ahb", "s-ahb";
> #address-cells = <2>;
> #size-cells = <2>;
> ranges;
> + iommus = <&apps_smmu 0x123 0x0>;
> status = "disabled";
>
> + i2c0: i2c@980000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0 0x00980000 0 0x4000>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + clock-names = "se";
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c0_data_clk>;
> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
> + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
> + <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "qup-core", "qup-config",
> + "qup-memory";
> + status = "disabled";
> + };
> +
> + spi0: spi@980000 {
> + compatible = "qcom,geni-spi";
> + reg = <0 0x00980000 0 0x4000>;
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + clock-names = "se";
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
This should only have qup_spi0_data_clk and qup_spi0_cs, not
qup_spi0_cs_gpio. Both qup controlled and gpio controlled options are
provided in case a board wants to use the qup version of chipselect, but
having them both used by default leads to conflicts and confusion. This
same comment applies to all spi pinctrl properties in this file. Please
keep the cs_gpio variants though so that boards can use them if they
want. They will be unused, but that's OK.
> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-domains = <&rpmhpd SC7280_CX>;
> + operating-points-v2 = <&qup_opp_table>;
> + interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
> + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
> + interconnect-names = "qup-core", "qup-config";
> + status = "disabled";
> + };
> +
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
@ 2021-09-22 12:31 rajpat
2021-09-22 14:54 ` Doug Anderson
0 siblings, 1 reply; 5+ messages in thread
From: rajpat @ 2021-09-22 12:31 UTC (permalink / raw)
To: Stephen Boyd
Cc: Andy Gross, Bjorn Andersson, Rob Herring, linux-arm-msm,
linux-kernel, devicetree, rnayak, saiprakash.ranjan, msavaliy,
skakit, mka, dianders, Roja Rani Yarubandi
On 2021-09-21 23:47, Stephen Boyd wrote:
> Quoting Rajesh Patil (2021-09-21 03:39:02)
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> index 2fbcb0a..b65c5da 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> @@ -536,24 +555,425 @@
>> qupv3_id_0: geniqup@9c0000 {
>> compatible = "qcom,geni-se-qup";
>> reg = <0 0x009c0000 0 0x2000>;
>> - clock-names = "m-ahb", "s-ahb";
>> clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
>> <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
>> + clock-names = "m-ahb", "s-ahb";
>> #address-cells = <2>;
>> #size-cells = <2>;
>> ranges;
>> + iommus = <&apps_smmu 0x123 0x0>;
>> status = "disabled";
>>
>> + i2c0: i2c@980000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0 0x00980000 0 0x4000>;
>> + clocks = <&gcc
>> GCC_QUPV3_WRAP0_S0_CLK>;
>> + clock-names = "se";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c0_data_clk>;
>> + interrupts = <GIC_SPI 601
>> IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interconnects = <&clk_virt
>> MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>> + <&gem_noc
>> MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
>> + <&aggre1_noc
>> MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
>> + interconnect-names = "qup-core",
>> "qup-config",
>> + "qup-memory";
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi@980000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0 0x00980000 0 0x4000>;
>> + clocks = <&gcc
>> GCC_QUPV3_WRAP0_S0_CLK>;
>> + clock-names = "se";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi0_data_clk>,
>> <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
>
> This should only have qup_spi0_data_clk and qup_spi0_cs, not
> qup_spi0_cs_gpio. Both qup controlled and gpio controlled options are
> provided in case a board wants to use the qup version of chipselect,
> but
> having them both used by default leads to conflicts and confusion. This
> same comment applies to all spi pinctrl properties in this file. Please
> keep the cs_gpio variants though so that boards can use them if they
> want. They will be unused, but that's OK.
Okay. Shall we remove only "<&qup_spiN_cs_gpio>" in each SPI node?
>
>> + interrupts = <GIC_SPI 601
>> IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + power-domains = <&rpmhpd SC7280_CX>;
>> + operating-points-v2 =
>> <&qup_opp_table>;
>> + interconnects = <&clk_virt
>> MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
>> + <&gem_noc
>> MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
>> + interconnect-names = "qup-core",
>> "qup-config";
>> + status = "disabled";
>> + };
>> +
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
2021-09-22 12:31 [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes rajpat
@ 2021-09-22 14:54 ` Doug Anderson
2021-09-23 10:13 ` rajpat
0 siblings, 1 reply; 5+ messages in thread
From: Doug Anderson @ 2021-09-22 14:54 UTC (permalink / raw)
To: Rajesh Patil
Cc: Stephen Boyd, Andy Gross, Bjorn Andersson, Rob Herring,
linux-arm-msm, LKML,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Rajendra Nayak, Sai Prakash Ranjan, msavaliy, satya priya,
Matthias Kaehlcke, Roja Rani Yarubandi
Hi,
On Wed, Sep 22, 2021 at 5:31 AM <rajpat@codeaurora.org> wrote:
>
> >> + spi0: spi@980000 {
> >> + compatible = "qcom,geni-spi";
> >> + reg = <0 0x00980000 0 0x4000>;
> >> + clocks = <&gcc
> >> GCC_QUPV3_WRAP0_S0_CLK>;
> >> + clock-names = "se";
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&qup_spi0_data_clk>,
> >> <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
> >
> > This should only have qup_spi0_data_clk and qup_spi0_cs, not
> > qup_spi0_cs_gpio. Both qup controlled and gpio controlled options are
> > provided in case a board wants to use the qup version of chipselect,
> > but
> > having them both used by default leads to conflicts and confusion. This
> > same comment applies to all spi pinctrl properties in this file. Please
> > keep the cs_gpio variants though so that boards can use them if they
> > want. They will be unused, but that's OK.
>
> Okay. Shall we remove only "<&qup_spiN_cs_gpio>" in each SPI node?
Right. So for this one:
pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
-Doug
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
2021-09-22 14:54 ` Doug Anderson
@ 2021-09-23 10:13 ` rajpat
0 siblings, 0 replies; 5+ messages in thread
From: rajpat @ 2021-09-23 10:13 UTC (permalink / raw)
To: Doug Anderson
Cc: Stephen Boyd, Andy Gross, Bjorn Andersson, Rob Herring,
linux-arm-msm, LKML,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Rajendra Nayak, Sai Prakash Ranjan, msavaliy, satya priya,
Matthias Kaehlcke, Roja Rani Yarubandi
On 2021-09-22 20:24, Doug Anderson wrote:
> Hi,
>
> On Wed, Sep 22, 2021 at 5:31 AM <rajpat@codeaurora.org> wrote:
>>
>> >> + spi0: spi@980000 {
>> >> + compatible = "qcom,geni-spi";
>> >> + reg = <0 0x00980000 0 0x4000>;
>> >> + clocks = <&gcc
>> >> GCC_QUPV3_WRAP0_S0_CLK>;
>> >> + clock-names = "se";
>> >> + pinctrl-names = "default";
>> >> + pinctrl-0 = <&qup_spi0_data_clk>,
>> >> <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
>> >
>> > This should only have qup_spi0_data_clk and qup_spi0_cs, not
>> > qup_spi0_cs_gpio. Both qup controlled and gpio controlled options are
>> > provided in case a board wants to use the qup version of chipselect,
>> > but
>> > having them both used by default leads to conflicts and confusion. This
>> > same comment applies to all spi pinctrl properties in this file. Please
>> > keep the cs_gpio variants though so that boards can use them if they
>> > want. They will be unused, but that's OK.
>>
>> Okay. Shall we remove only "<&qup_spiN_cs_gpio>" in each SPI node?
>
> Right. So for this one:
>
> pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
>
> -Doug
Okay.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-09-23 10:13 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2021-09-22 12:31 [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes rajpat
2021-09-22 14:54 ` Doug Anderson
2021-09-23 10:13 ` rajpat
-- strict thread matches above, loose matches on Subject: below --
2021-09-21 10:38 [PATCH V9 0/8] Add QSPI and QUPv3 DT nodes for SC7280 SoC Rajesh Patil
2021-09-21 10:39 ` [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes Rajesh Patil
2021-09-21 18:17 ` Stephen Boyd
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).