Re: [PATCH v4 1/2] ARM: dts: sun7i: Add Iteaduino Plus A20

["Jernej Škrabec" <jernej.skrabec@gmail.com>]

Dne petek, 06. oktober 2023 ob 11:01:30 CEST je Julian Ribbeck napisal(a):
> Iteaduino Plus A20 is very similar to Iteaduino Plus A10. In fact it
> shares the same breakout board and the Itead Core A20 on top of it, is
> only adapted to support the dual-core A20.
> 
> This commits enables the following hardware:
> 
> * HDMI Video output
> * USB
> * SATA (untested due to lack of hardware I could attach)
> * Ethernet
> * MMC storage
> * UART
> * USB OTG (untested, because I don't own an USB OTG cable/device)
> 
> Signed-off-by: Julian Ribbeck <julian.ribbeck@gmx.de>
> ---
>  arch/arm/boot/dts/allwinner/Makefile          |   1 +
>  .../sun7i-a20-itead-iteaduino-plus.dts        | 104 ++++++++++++++++++
>  2 files changed, 105 insertions(+)
>  create mode 100644 arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts
> 
> diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> index eebb5a0c873a..39af5ad94590 100644
> --- a/arch/arm/boot/dts/allwinner/Makefile
> +++ b/arch/arm/boot/dts/allwinner/Makefile
> @@ -124,6 +124,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
>  	sun7i-a20-haoyu-marsboard.dtb \
>  	sun7i-a20-hummingbird.dtb \
>  	sun7i-a20-itead-ibox.dtb \
> +	sun7i-a20-itead-iteaduino-plus.dts \

This should be .dtb.

Other than that:
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>

I'll fix it while applying.

For future reference, please follow proper patch submission procedure:
- each revision should be sent in separate thread
- each new revision should contain changelog, either in cover letter (when
there is more than one patch) or below --- line in each patch
- compatible description patch comes before first usage (I'll invert order
when applying)

Best regards,
Jernej

>  	sun7i-a20-i12-tvbox.dtb \
>  	sun7i-a20-icnova-a20-adb4006.dtb \
>  	sun7i-a20-icnova-swac.dtb \
> diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts
> new file mode 100644
> index 000000000000..c9f9b0275381
> --- /dev/null
> +++ b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-iteaduino-plus.dts
> @@ -0,0 +1,104 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-itead-core-common.dtsi"
> +
> +/ {
> +	model = "Itead Iteaduino Plus A20";
> +	compatible = "itead,iteaduino-plus-a20", "allwinner,sun7i-a20";
> +
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +};
> +
> +&ac_power_supply {
> +	status = "okay";
> +};
> +
> +&ahci {
> +	target-supply = <&reg_ahci_5v>;
> +	status = "okay";
> +};
> +
> +&axp209 {
> +	interrupt-parent = <&nmi_intc>;
> +	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +};
> +
> +&battery_power_supply {
> +	status = "okay";
> +};
> +
> +&codec {
> +	stauts = "okay";
> +};
> +
> +&de {
> +	status = "okay";
> +};
> +
> +&emac {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emac_pa_pins>;
> +	phy-handle = <&phy1>;
> +	status = "okay";
> +};
> +
> +&emac_sram {
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	status = "okay";
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +&mdio {
> +	status = "okay";
> +
> +	phy1: ethernet-phy@1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
> +	status = "okay";
> +};
> +
> +&otg_sram {
> +	status = "okay";
> +};
> +
> +&reg_ahci_5v {
> +	status = "okay";
> +};
> +
> +&reg_usb0_vbus {
> +	status = "okay";
> +};
> +
> +&usb_otg {
> +	status = "okay";
> +	dr_mode = "host";
> +};
> +
> +&usbphy {
> +	usb0_vbus-supply = <&reg_usb0_vbus>;
> +};
> --
> 2.42.0
> 
>