Re: [PATCH v13 3/5] arm64: dts: qcom: ipq9574: Add USB related nodes

[Dmitry Baryshkov <dmitry.baryshkov@linaro.org>]

On 08/06/2023 12:28, Varadarajan Narayanan wrote:
> Add USB phy and controller related nodes
> 
> SS PHY need two supplies and HS PHY needs three supplies. 0.925V
> and 3.3V are from fixed regulators and 1.8V is generated from
> PMIC's LDO
> 
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> ---
>   Changes in v13:
> 	- Move fixed regulator definitions from SoC dtsi to board dts
> 	- Remove 'dr_mode' from SoC dtsi
> 	- Move 'status' property to the end
>   Changes in v12:
> 	- Rebase
>   Changes in v11:
> 	- Rename dwc_0 -> usb_0_dwc3
>   Changes in v10:
> 	- Fix regulator definitions
>   Changes in v8:
> 	- Change clocks order to match the bindings
>   Changes in v7:
> 	- Change com_aux -> cfg_ahb
>   Changes in v6:
> 	- Introduce fixed regulators for the phy
> 	- Resolved all 'make dtbs_check' messages
> 
>   Changes in v5:
> 	- Fix additional comments
> 	- Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml
> 	- 'make dtbs_check' giving the following messages since
> 	  ipq9574 doesn't have power domains. Hope this is ok
> 
> 		/local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property
>          	From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml
> 		/local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property
>          	From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> 
>   Changes in v4:
> 	- Use newer bindings without subnodes
> 	- Fix coding style issues
> 
>   Changes in v3:
> 	- Insert the nodes at proper location
> 
>   Changes in v2:
> 	- Fixed issues flagged by Krzysztof
> 	- Fix issues reported by make dtbs_check
> 	- Remove NOC related clocks (to be added with proper
> 	  interconnect support)
> ---
>   arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 18 ++++++
>   arch/arm64/boot/dts/qcom/ipq9574.dtsi       | 85 +++++++++++++++++++++++++++++
>   2 files changed, 103 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> index 2b3ed8d..8261a2b 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> @@ -21,6 +21,24 @@
>   	chosen {
>   		stdout-path = "serial0:115200n8";
>   	};
> +
> +	regulator_fixed_3p3: s3300 {

Nit: these two regulators are not references from SoC dtsi. So they can 
be moved to one of the next commits.

> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		regulator-name = "fixed_3p3";
> +	};
> +
> +	regulator_fixed_0p925: s0925 {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <925000>;
> +		regulator-max-microvolt = <925000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		regulator-name = "fixed_0p925";
> +	};
>   };
>   
>   &blsp1_uart2 {
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 0baeb10..feabc19 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -465,6 +465,91 @@
>   			status = "disabled";
>   		};
>   
> +		usb_0_qusbphy: phy@7b000 {
> +			compatible = "qcom,ipq9574-qusb2-phy";
> +			reg = <0x0007b000 0x180>;
> +			#phy-cells = <0>;
> +
> +			clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> +				 <&xo_board_clk>;
> +			clock-names = "cfg_ahb",
> +				      "ref";
> +
> +			resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
> +			status = "disabled";
> +		};
> +
> +		usb_0_qmpphy: phy@7d000 {
> +			compatible = "qcom,ipq9574-qmp-usb3-phy";
> +			reg = <0x0007d000 0xa00>;
> +			#phy-cells = <0>;
> +
> +			clocks = <&gcc GCC_USB0_AUX_CLK>,
> +				 <&xo_board_clk>,
> +				 <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> +				 <&gcc GCC_USB0_PIPE_CLK>;
> +			clock-names = "aux",
> +				      "ref",
> +				      "cfg_ahb",
> +				      "pipe";
> +
> +			resets = <&gcc GCC_USB0_PHY_BCR>,
> +				 <&gcc GCC_USB3PHY_0_PHY_BCR>;
> +			reset-names = "phy",
> +				      "phy_phy";
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "usb0_pipe_clk";
> +
> +			status = "disabled";
> +		};
> +
> +		usb3: usb@8af8800 {
> +			compatible = "qcom,ipq9574-dwc3", "qcom,dwc3";
> +			reg = <0x08af8800 0x400>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			clocks = <&gcc GCC_SNOC_USB_CLK>,
> +				 <&gcc GCC_USB0_MASTER_CLK>,
> +				 <&gcc GCC_ANOC_USB_AXI_CLK>,
> +				 <&gcc GCC_USB0_SLEEP_CLK>,
> +				 <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> +
> +			clock-names = "cfg_noc",
> +				      "core",
> +				      "iface",
> +				      "sleep",
> +				      "mock_utmi";
> +
> +			assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>,
> +					  <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> +			assigned-clock-rates = <200000000>,
> +					       <24000000>;
> +
> +			interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "pwr_event";
> +
> +			resets = <&gcc GCC_USB_BCR>;
> +			status = "disabled";
> +
> +			usb_0_dwc3: usb@8a00000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x8a00000 0xcd00>;
> +				clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> +				clock-names = "ref";
> +				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> +				phys = <&usb_0_qusbphy>, <&usb_0_qmpphy>;
> +				phy-names = "usb2-phy", "usb3-phy";
> +				tx-fifo-resize;
> +				snps,is-utmi-l1-suspend;
> +				snps,hird-threshold = /bits/ 8 <0x0>;
> +				snps,dis_u2_susphy_quirk;
> +				snps,dis_u3_susphy_quirk;
> +			};
> +		};
> +
>   		intc: interrupt-controller@b000000 {
>   			compatible = "qcom,msm-qgic2";
>   			reg = <0x0b000000 0x1000>,  /* GICD */

-- 
With best wishes
Dmitry