* [PATCH 2/3] arm64: dts: qcom: sm8650: add support for the SM8650-HDK board
2024-02-23 8:52 [PATCH 0/3] arm64: qcom: sm8650: add support for the SM8650-HDK board Neil Armstrong
2024-02-23 8:52 ` [PATCH 1/3] dt-bindings: arm: qcom: Document the HDK8650 board Neil Armstrong
@ 2024-02-23 8:52 ` Neil Armstrong
2024-03-02 23:26 ` Vladimir Zapolskiy
2024-03-12 14:48 ` Konrad Dybcio
2024-02-23 8:52 ` [PATCH 3/3] arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay Neil Armstrong
2 siblings, 2 replies; 11+ messages in thread
From: Neil Armstrong @ 2024-02-23 8:52 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Neil Armstrong
The SM8650-HDK is an embedded development platforms for the
Snapdragon 8 Gen 3 SoC aka SM8650, with the following features:
- Qualcomm SM8650 SoC
- 16GiB On-board LPDDR5
- On-board WiFi 7 + Bluetooth 5.3/BLE
- On-board UFS4.0
- M.2 Key B+M Gen3x2 PCIe Slot
- HDMI Output
- USB-C Connector with DP Almode & Audio Accessory mode
- Micro-SDCard Slot
- Audio Jack with Playback and Microphone
- 2 On-board Analog microphones
- 2 On-board Speakers
- 96Boards Compatible Low-Speed and High-Speed connectors [1]
- For Camera, Sensors and external Display cards
- Compatible with the Linaro Debug board [2]
- SIM Slot for Modem
- Debug connectors
- 6x On-Board LEDs
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 1259 +++++++++++++++++++++++++++++++
2 files changed, 1260 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..4f48c98451de 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8650-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
new file mode 100644
index 000000000000..cb1e0f569483
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
@@ -0,0 +1,1259 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8650.dtsi"
+#include "pm8010.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 8
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. SM8650 HDK";
+ compatible = "qcom,sm8650-hdk", "qcom,sm8650";
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart15;
+ serial1 = &uart14;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_out: endpoint {
+ remote-endpoint = <<9611_out>;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_BLUETOOTH;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pm8550b_gpios 9 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ panic-indicator;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_ORANGE>;
+ gpios = <&pm8550b_gpios 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sm8650-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&wcd_usbss_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ lt9611_1v2: regulator-lt9611-1v2 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "LT9611_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ vin-supply = <&vph_pwr>;
+ gpio = <&tlmm 79 GPIO_ACTIVE_HIGH>;
+
+ enable-active-high;
+ };
+
+ lt9611_3v3: regulator-lt9611-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "LT9611_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ vin-supply = <&vreg_bob_3v3>;
+ gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>;
+
+ enable-active-high;
+ };
+
+ sound {
+ compatible = "qcom,sm8650-sndcard", "qcom,sm8450-sndcard";
+ model = "SM8650-HDK";
+ audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA_SPK2 OUT",
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC1", "MIC BIAS1",
+ "AMIC2", "MIC BIAS2",
+ "AMIC5", "MIC BIAS4",
+ "TX SWR_INPUT0", "ADC1_OUTPUT",
+ "TX SWR_INPUT1", "ADC2_OUTPUT",
+ "TX SWR_INPUT3", "ADC4_OUTPUT";
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&wcd939x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ codec {
+ sound-dai = <&wcd939x 1>, <&swr2 0>, <&lpass_txmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_bob_3v3: regulator-vreg-bob-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_BOB_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ vin-supply = <&vph_pwr>;
+ };
+
+ wcd939x: audio-codec {
+ compatible = "qcom,wcd9395-codec", "qcom,wcd9390-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ reset-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_l15b_1p8>;
+ vdd-rxtx-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l15b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ #sound-dai-cells = <1>;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l3-supply = <&vreg_s1c_1p2>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob1>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l11-supply = <&vreg_s1c_1p2>;
+ vdd-l12-supply = <&vreg_s6c_1p8>;
+ vdd-l15-supply = <&vreg_s6c_1p8>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ qcom,pmic-id = "b";
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s1c_1p2>;
+ vdd-l2-supply = <&vreg_s1c_1p2>;
+ vdd-l3-supply = <&vreg_s1c_1p2>;
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+
+ qcom,pmic-id = "c";
+
+ vreg_s1c_1p2: smps1 {
+ regulator-name = "vreg_s1c_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1348000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2c_0p8: smps2 {
+ regulator-name = "vreg_s2c_0p8";
+ regulator-min-microvolt = <852000>;
+ regulator-max-microvolt = <1036000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3c_0p9: smps3 {
+ regulator-name = "vreg_s3c_0p9";
+ regulator-min-microvolt = <976000>;
+ regulator-max-microvolt = <1064000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4c_1p2: smps4 {
+ regulator-name = "vreg_s4c_1p2";
+ regulator-min-microvolt = <1224000>;
+ regulator-max-microvolt = <1280000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5c_0p7: smps5 {
+ regulator-name = "vreg_s5c_0p7";
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6c_1p8: smps6 {
+ regulator-name = "vreg_s6c_1p8";
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p2: ldo1 {
+ regulator-name = "vreg_l1c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_1p2: ldo3 {
+ regulator-name = "vreg_l3c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s3c_0p9>;
+
+ qcom,pmic-id = "d";
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l3-supply = <&vreg_s3c_0p9>;
+
+ qcom,pmic-id = "e";
+
+ vreg_l3e_0p9: ldo3 {
+ regulator-name = "vreg_l3e_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s3c_0p9>;
+ vdd-l3-supply = <&vreg_s3c_0p9>;
+
+ qcom,pmic-id = "g";
+
+ vreg_l1g_0p91: ldo1 {
+ regulator-name = "vreg_l1g_0p91";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_0p91: ldo3 {
+ regulator-name = "vreg_l3g_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s3c_0p9>;
+ vdd-l2-supply = <&vreg_s3c_0p9>;
+ vdd-l3-supply = <&vreg_s1c_1p2>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ qcom,pmic-id = "i";
+
+ vreg_s4i_0p85: smps4 {
+ regulator-name = "vreg_s4i_0p85";
+ regulator-min-microvolt = <852000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1i_0p88: ldo1 {
+ regulator-name = "vreg_l1i_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2i_0p88: ldo2 {
+ regulator-name = "vreg_l2i_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3i_1p2: ldo3 {
+ regulator-name = "vreg_l3i_0p91";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vdd-l1-l2-supply = <&vreg_s1c_1p2>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6c_1p8>;
+ vdd-l6-supply = <&vreg_bob1>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1m_1p1: ldo1 {
+ regulator-name = "vreg_l1m_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_2p8: ldo6 {
+ regulator-name = "vreg_l6m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p96: ldo7 {
+ regulator-name = "vreg_l7m_2p96";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vdd-l1-l2-supply = <&vreg_s1c_1p2>;
+ vdd-l3-l4-supply = <&vreg_s6c_1p8>;
+ vdd-l5-supply = <&vreg_bob2>;
+ vdd-l6-supply = <&vreg_bob2>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p056: ldo2 {
+ regulator-name = "vreg_l2n_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_1p8: ldo3 {
+ regulator-name = "vreg_l3n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_1p8: ldo4 {
+ regulator-name = "vreg_l4n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_2p8: ldo5 {
+ regulator-name = "vreg_l5n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_2p8: ldo6 {
+ regulator-name = "vreg_l6n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_3p3: ldo7 {
+ regulator-name = "vreg_l7n_3p3";
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c6 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ lt9611_codec: hdmi-bridge@2b {
+ compatible = "lontium,lt9611uxc";
+ reg = <0x2b>;
+
+ interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+
+ reset-gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <<9611_1v2>;
+ vcc-supply = <<9611_3v3>;
+
+ pinctrl-0 = <<9611_irq_pin>, <<9611_rst_pin>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lt9611_a: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lt9611_out: endpoint {
+ remote-endpoint = <&hdmi_connector_out>;
+ };
+ };
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ wcd_usbss: typec-mux@e {
+ compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
+ reg = <0xe>;
+
+ vdd-supply = <&vreg_l15b_1p8>;
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+
+ mode-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wcd_usbss_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+ };
+};
+
+&ipa {
+ qcom,gsi-loader = "self";
+ memory-region = <&ipa_fw_mem>;
+ firmware-name = "qcom/sm8650/ipa_fws.mbn";
+ status = "okay";
+};
+
+&lpass_tlmm {
+ spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <<9611_a>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+ clock-frequency = <1000>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1i_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l3e_0p9>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+ vdda-qref-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&pm8550_gpios {
+ sdc2_card_det_n: sdc2-card-det-state {
+ pins = "gpio12";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ output-disable;
+ power-source = <1>; /* 1.8 V */
+ };
+
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ power-source = <1>;
+ };
+};
+
+/* The RGB signals are routed to 3 separate LEDs on the HDK8650 */
+&pm8550_pwm {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ led@1 {
+ reg = <1>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ };
+
+ led@2 {
+ reg = <2>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ };
+
+ led@3 {
+ reg = <3>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "off";
+ };
+};
+
+&pm8550b_eusb2_repeater {
+ vdd18-supply = <&vreg_l15b_1p8>;
+ vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_rtc {
+ status = "okay";
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&qup_i2c3_data_clk {
+ /* Use internal I2C pull-up */
+ bias-pull-up = <2200>;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8650/adsp.mbn",
+ "qcom/sm8650/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8650/cdsp.mbn",
+ "qcom/sm8650/cdsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8650/modem.mbn",
+ "qcom/sm8650/modem_dtb.mbn";
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;
+
+ vmmc-supply = <&vreg_l9b_2p9>;
+ vqmmc-supply = <&vreg_l8b_1p8>;
+ bus-width = <4>;
+ no-sdio;
+ no-mmc;
+
+ pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
+ pinctrl-names = "default", "sleep";
+
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&swr0 {
+ status = "okay";
+
+ /* WSA8845, Speaker North */
+ north_spkr: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ pinctrl-0 = <&spkr_1_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&lpass_tlmm 21 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l3c_1p2>;
+ };
+
+ /* WSA8845, Speaker South */
+ south_spkr: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ pinctrl-0 = <&spkr_2_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l3c_1p2>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ /* WCD9395 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010e00";
+ reg = <0 4>;
+
+ /*
+ * WCD9395 RX Port 1 (HPH_L/R) <=> SWR1 Port 1 (HPH_L/R)
+ * WCD9395 RX Port 2 (CLSH) <=> SWR1 Port 2 (CLSH)
+ * WCD9395 RX Port 3 (COMP_L/R) <=> SWR1 Port 3 (COMP_L/R)
+ * WCD9395 RX Port 4 (LO) <=> SWR1 Port 4 (LO)
+ * WCD9395 RX Port 5 (DSD_L/R) <=> SWR1 Port 5 (DSD_L/R)
+ * WCD9395 RX Port 6 (HIFI_PCM_L/R) <=> SWR1 Port 9 (HIFI_PCM_L/R)
+ */
+ qcom,rx-port-mapping = <1 2 3 4 5 9>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9395 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010e00";
+ reg = <0 3>;
+
+ /*
+ * WCD9395 TX Port 1 (ADC1,2,3,4) <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3)
+ * WCD9395 TX Port 2 (ADC3,4 & DMIC0,1) <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3)
+ * WCD9395 TX Port 3 (DMIC0,1,2,3 & MBHC) <=> SWR2 Port 3 (TX SWR_INPUT 4,5,6,7)
+ * WCD9395 TX Port 4 (DMIC4,5,6,7) <=> SWR2 Port 4 (TX SWR_INPUT 8,9,10,11)
+ */
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
+&tlmm {
+ /* Reserved I/Os for NFC */
+ gpio-reserved-ranges = <32 8>, <74 1>;
+
+ bt_default: bt-default-state {
+ bt-en-pins {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ sw-ctrl-pins {
+ pins = "gpio18";
+ function = "gpio";
+ bias-pull-down;
+ };
+ };
+
+ lt9611_irq_pin: lt9611-irq-state {
+ pins = "gpio85";
+ function = "gpio";
+ bias-disable;
+ };
+
+ lt9611_rst_pin: lt9611-rst-state {
+ pins = "gpio28";
+ function = "gpio";
+ output-high;
+ };
+
+ spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+ pins = "gpio77";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio107";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+
+ vddio-supply = <&vreg_l3c_1p2>;
+ vddaon-supply = <&vreg_l15b_1p8>;
+ vdddig-supply = <&vreg_s3c_0p9>;
+ vddrfa0p8-supply = <&vreg_s3c_0p9>;
+ vddrfa1p2-supply = <&vreg_s1c_1p2>;
+ vddrfa1p9-supply = <&vreg_s6c_1p8>;
+
+ max-speed = <3200000>;
+
+ enable-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
+ swctrl-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&bt_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&uart15 {
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1c_1p2>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+/*
+ * DPAUX -> WCD9395 -> USB_SBU -> USB-C
+ * eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> WCD9395 -> USB-C
+ * USB SS -> USB-C
+ */
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l1i_0p88>;
+ vdda12-supply = <&vreg_l3i_1p2>;
+
+ phys = <&pm8550b_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy {
+ vdda-phy-supply = <&vreg_l3i_1p2>;
+ vdda-pll-supply = <&vreg_l3g_0p91>;
+
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy_dp_in {
+ remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 11+ messages in thread