[PATCH v9 01/11] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[PATCH v9 01/11] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Andre Przywara]

The AXP305 PMIC used on many boards with the H616 SoC seems to be fully
compatible to the AXP805 PMIC, so add the proper chain of compatible
strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line
connected to the CPU, so make the "interrupts" property optional.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index 4991a6415796..2b53dcc0ea61 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -26,10 +26,10 @@ Required properties:
     * "x-powers,axp803"
     * "x-powers,axp806"
     * "x-powers,axp805", "x-powers,axp806"
+    * "x-powers,axp305", "x-powers,axp805", "x-powers,axp806"
     * "x-powers,axp809"
     * "x-powers,axp813"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
@@ -43,6 +43,7 @@ more information:
 			AXP20x/LDO3: software-based implementation
 
 Optional properties:
+- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
 		      AXP22X/8XX: range: 1800-4050, Default: 3   MHz
-- 
2.17.6

Re: [PATCH v9 01/11] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)

[Lee Jones]

On Mon, 02 Aug 2021, Andre Przywara wrote:

> The AXP305 PMIC used on many boards with the H616 SoC seems to be fully
> compatible to the AXP805 PMIC, so add the proper chain of compatible
> strings.
> 
> Also at least on one board (Orangepi Zero2) there is no interrupt line
> connected to the CPU, so make the "interrupts" property optional.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
>  Documentation/devicetree/bindings/mfd/axp20x.txt | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)

Applied, thanks.

-- 
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

[PATCH v9 02/11] dt-bindings: rtc: sun6i: Add H616 compatible string

[Andre Przywara]

Add the obvious compatible name to the existing RTC binding.
The actual RTC part of the device uses a different day/month/year
storage scheme, so it's not compatible with the previous devices.
Also the clock part is quite different, as there is no external 32K LOSC
oscillator input.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml      | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index beeb90e55727..d8a6500e5840 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -26,6 +26,7 @@ properties:
           - const: allwinner,sun50i-a64-rtc
           - const: allwinner,sun8i-h3-rtc
       - const: allwinner,sun50i-h6-rtc
+      - const: allwinner,sun50i-h616-rtc
 
   reg:
     maxItems: 1
@@ -104,6 +105,19 @@ allOf:
           minItems: 3
           maxItems: 3
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: allwinner,sun50i-h616-rtc
+
+    then:
+      properties:
+        clock-output-names:
+          minItems: 3
+          maxItems: 3
+        clocks: false
+
   - if:
       properties:
         compatible:
-- 
2.17.6

Re: [PATCH v9 02/11] dt-bindings: rtc: sun6i: Add H616 compatible string

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1683 bytes --]

On Mon, Aug 02, 2021 at 01:39:43AM +0100, Andre Przywara wrote:
> Add the obvious compatible name to the existing RTC binding.
> The actual RTC part of the device uses a different day/month/year
> storage scheme, so it's not compatible with the previous devices.
> Also the clock part is quite different, as there is no external 32K LOSC
> oscillator input.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
>  .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml      | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
> index beeb90e55727..d8a6500e5840 100644
> --- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
> +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
> @@ -26,6 +26,7 @@ properties:
>            - const: allwinner,sun50i-a64-rtc
>            - const: allwinner,sun8i-h3-rtc
>        - const: allwinner,sun50i-h6-rtc
> +      - const: allwinner,sun50i-h616-rtc
>  
>    reg:
>      maxItems: 1
> @@ -104,6 +105,19 @@ allOf:
>            minItems: 3
>            maxItems: 3
>  
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            const: allwinner,sun50i-h616-rtc
> +
> +    then:
> +      properties:
> +        clock-output-names:
> +          minItems: 3
> +          maxItems: 3

The comments I made here on the v7 are still relevant: you only need one
of these two, and the list of clocks should be documented.

Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[PATCH v9 08/11] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

[Andre Przywara]

This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
And while there is still the extra sunxi interrupt controller, the
package lacks the corresponding NMI pin, so no interrupts for the PMIC.

The reserved memory node is actually handled by Trusted Firmware now,
but U-Boot fails to propagate this to a separately loaded DTB, so we
keep it in here for now, until U-Boot learns to do this properly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 575 ++++++++++++++++++
 1 file changed, 575 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 000000000000..6a15ff2e7ebf
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,575 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved: secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x80000>;
+			no-map;
+		};
+	};
+
+	osc24M: osc24M-clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		arm,no-tick-in-suspend;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun50i-h616-system-control";
+			reg = <0x03000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@28000 {
+				compatible = "mmio-sram";
+				reg = <0x00028000 0x30000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00028000 0x30000>;
+			};
+		};
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h616-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		watchdog: watchdog@30090a0 {
+			compatible = "allwinner,sun50i-h616-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x030090a0 0x20>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+			status = "okay";
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h616-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+
+			ext_rgmii_pins: rgmii-pins {
+				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+				       "PI5", "PI7", "PI8", "PI9", "PI10",
+				       "PI11", "PI12", "PI13", "PI14", "PI15",
+				       "PI16";
+				function = "emac0";
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PI6", "PI7";
+				function = "i2c0";
+			};
+
+			i2c3_ph_pins: i2c3-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c3";
+			};
+
+			ir_rx_pin: ir-rx-pin {
+				pins = "PH10";
+				function = "ir_rx";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			spi0_pins: spi0-pins {
+				pins = "PC0", "PC2", "PC3", "PC4";
+				function = "spi0";
+			};
+
+			spi1_pins: spi1-pins {
+				pins = "PH6", "PH7", "PH8";
+				function = "spi1";
+			};
+
+			spi1_cs_pin: spi1-cs-pin {
+				pins = "PH5";
+				function = "spi1";
+			};
+
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun50i-h616-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@5001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001400 0x400>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c4: i2c@5003000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05003000 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@5010000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05010000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@5011000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05011000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac0: ethernet@5020000 {
+			compatible = "allwinner,sun50i-h616-emac",
+				     "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x05020000 0x10000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC0>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC0>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		rtc: rtc@7000000 {
+			compatible = "allwinner,sun50i-h616-rtc";
+			reg = <0x07000000 0x400>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out", "iosc";
+			#clock-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-h616-r-ccu";
+			reg = <0x07010000 0x210>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-h616-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+			};
+
+			r_rsb_pins: r-rsb-pins {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+			};
+		};
+
+		ir: ir@7040000 {
+				compatible = "allwinner,sun50i-h616-ir",
+					     "allwinner,sun6i-a31-ir";
+				reg = <0x07040000 0x400>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&r_ccu CLK_R_APB1_IR>,
+					 <&r_ccu CLK_IR>;
+				clock-names = "apb", "ir";
+				resets = <&r_ccu RST_R_APB1_IR>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ir_rx_pin>;
+				status = "disabled";
+		};
+
+		r_i2c: i2c@7081400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			resets = <&r_ccu RST_R_APB2_I2C>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_rsb: rsb@7083000 {
+			compatible = "allwinner,sun50i-h616-rsb",
+				     "allwinner,sun8i-a23-rsb";
+			reg = <0x07083000 0x400>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_RSB>;
+			clock-frequency = <3000000>;
+			resets = <&r_ccu RST_R_APB2_RSB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.17.6

Re: [PATCH v9 08/11] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

[Samuel Holland]

Hi Andre,

I took another look at this while working on the RTC binding.

On 8/1/21 7:39 PM, Andre Przywara wrote:
> This (relatively) new SoC is similar to the H6, but drops the (broken)
> PCIe support and the USB 3.0 controller. It also gets the management
> controller removed, which in turn removes *some*, but not all of the
> devices formerly dedicated to the ARISC (CPUS).
> And while there is still the extra sunxi interrupt controller, the
> package lacks the corresponding NMI pin, so no interrupts for the PMIC.
> 
> The reserved memory node is actually handled by Trusted Firmware now,
> but U-Boot fails to propagate this to a separately loaded DTB, so we
> keep it in here for now, until U-Boot learns to do this properly.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 575 ++++++++++++++++++
>  1 file changed, 575 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> new file mode 100644
> index 000000000000..6a15ff2e7ebf
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> @@ -0,0 +1,575 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +// Copyright (C) 2020 Arm Ltd.
> +// based on the H6 dtsi, which is:
> +//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/sun50i-h616-ccu.h>
> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
> +#include <dt-bindings/reset/sun50i-h616-ccu.h>
> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
> +
> +/ {
> +	interrupt-parent = <&gic>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@0 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <0>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <1>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +
> +		cpu2: cpu@2 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <2>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +
> +		cpu3: cpu@3 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			reg = <3>;
> +			enable-method = "psci";
> +			clocks = <&ccu CLK_CPUX>;
> +		};
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
> +		secmon_reserved: secmon@40000000 {
> +			reg = <0x0 0x40000000 0x0 0x80000>;
> +			no-map;
> +		};
> +	};
> +
> +	osc24M: osc24M-clk {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <24000000>;
> +		clock-output-names = "osc24M";
> +	};
> +
> +	pmu {
> +		compatible = "arm,cortex-a53-pmu";
> +		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2";
> +		method = "smc";
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		arm,no-tick-in-suspend;
> +		interrupts = <GIC_PPI 13
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 14
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 11
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 10
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +	};
> +
> +	soc@0 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0x0 0x0 0x0 0x40000000>;
> +
> +		syscon: syscon@3000000 {
> +			compatible = "allwinner,sun50i-h616-system-control";
> +			reg = <0x03000000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			sram_c: sram@28000 {
> +				compatible = "mmio-sram";
> +				reg = <0x00028000 0x30000>;
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				ranges = <0 0x00028000 0x30000>;
> +			};
> +		};
> +
> +		ccu: clock@3001000 {
> +			compatible = "allwinner,sun50i-h616-ccu";
> +			reg = <0x03001000 0x1000>;
> +			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
> +			clock-names = "hosc", "losc", "iosc";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		watchdog: watchdog@30090a0 {
> +			compatible = "allwinner,sun50i-h616-wdt",
> +				     "allwinner,sun6i-a31-wdt";
> +			reg = <0x030090a0 0x20>;
> +			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&osc24M>;
> +			status = "okay";

A status of "okay" is the default.

> +		};
> +
> +		pio: pinctrl@300b000 {
> +			compatible = "allwinner,sun50i-h616-pinctrl";
> +			reg = <0x0300b000 0x400>;
> +			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
> +			clock-names = "apb", "hosc", "losc";
> +			gpio-controller;
> +			#gpio-cells = <3>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			#address-cells = <0>;
> +
> +			ext_rgmii_pins: rgmii-pins {
> +				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
> +				       "PI5", "PI7", "PI8", "PI9", "PI10",
> +				       "PI11", "PI12", "PI13", "PI14", "PI15",
> +				       "PI16";
> +				function = "emac0";
> +				drive-strength = <40>;
> +			};
> +
> +			i2c0_pins: i2c0-pins {
> +				pins = "PI6", "PI7";
> +				function = "i2c0";
> +			};
> +
> +			i2c3_ph_pins: i2c3-ph-pins {
> +				pins = "PH4", "PH5";
> +				function = "i2c3";
> +			};
> +
> +			ir_rx_pin: ir-rx-pin {
> +				pins = "PH10";
> +				function = "ir_rx";
> +			};
> +
> +			mmc0_pins: mmc0-pins {
> +				pins = "PF0", "PF1", "PF2", "PF3",
> +				       "PF4", "PF5";
> +				function = "mmc0";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			mmc1_pins: mmc1-pins {
> +				pins = "PG0", "PG1", "PG2", "PG3",
> +				       "PG4", "PG5";
> +				function = "mmc1";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			mmc2_pins: mmc2-pins {
> +				pins = "PC0", "PC1", "PC5", "PC6",
> +				       "PC8", "PC9", "PC10", "PC11",
> +				       "PC13", "PC14", "PC15", "PC16";
> +				function = "mmc2";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			spi0_pins: spi0-pins {
> +				pins = "PC0", "PC2", "PC3", "PC4";
> +				function = "spi0";
> +			};
> +
> +			spi1_pins: spi1-pins {
> +				pins = "PH6", "PH7", "PH8";
> +				function = "spi1";
> +			};
> +
> +			spi1_cs_pin: spi1-cs-pin {
> +				pins = "PH5";
> +				function = "spi1";
> +			};
> +
> +			uart0_ph_pins: uart0-ph-pins {
> +				pins = "PH0", "PH1";
> +				function = "uart0";
> +			};
> +
> +			uart1_pins: uart1-pins {
> +				pins = "PG6", "PG7";
> +				function = "uart1";
> +			};
> +
> +			uart1_rts_cts_pins: uart1-rts-cts-pins {
> +				pins = "PG8", "PG9";
> +				function = "uart1";
> +			};
> +		};
> +
> +		gic: interrupt-controller@3021000 {
> +			compatible = "arm,gic-400";
> +			reg = <0x03021000 0x1000>,
> +			      <0x03022000 0x2000>,
> +			      <0x03024000 0x2000>,
> +			      <0x03026000 0x2000>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			#address-cells = <0>;
> +		};
> +
> +		mmc0: mmc@4020000 {
> +			compatible = "allwinner,sun50i-h616-mmc",
> +				     "allwinner,sun50i-a100-mmc";
> +			reg = <0x04020000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC0>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc0_pins>;
> +			status = "disabled";
> +			max-frequency = <150000000>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			cap-sdio-irq;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc1: mmc@4021000 {
> +			compatible = "allwinner,sun50i-h616-mmc",
> +				     "allwinner,sun50i-a100-mmc";
> +			reg = <0x04021000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC1>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc1_pins>;
> +			status = "disabled";
> +			max-frequency = <150000000>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			cap-sdio-irq;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc2: mmc@4022000 {
> +			compatible = "allwinner,sun50i-h616-emmc",
> +				     "allwinner,sun50i-a100-emmc";
> +			reg = <0x04022000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC2>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc2_pins>;
> +			status = "disabled";
> +			max-frequency = <150000000>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			cap-sdio-irq;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		uart0: serial@5000000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART0>;
> +			resets = <&ccu RST_BUS_UART0>;
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@5000400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000400 0x400>;
> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART1>;
> +			resets = <&ccu RST_BUS_UART1>;
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@5000800 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000800 0x400>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART2>;
> +			resets = <&ccu RST_BUS_UART2>;
> +			status = "disabled";
> +		};
> +
> +		uart3: serial@5000c00 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05000c00 0x400>;
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART3>;
> +			resets = <&ccu RST_BUS_UART3>;
> +			status = "disabled";
> +		};
> +
> +		uart4: serial@5001000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05001000 0x400>;
> +			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART4>;
> +			resets = <&ccu RST_BUS_UART4>;
> +			status = "disabled";
> +		};
> +
> +		uart5: serial@5001400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x05001400 0x400>;
> +			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&ccu CLK_BUS_UART5>;
> +			resets = <&ccu RST_BUS_UART5>;
> +			status = "disabled";
> +		};
> +
> +		i2c0: i2c@5002000 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002000 0x400>;
> +			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C0>;
> +			resets = <&ccu RST_BUS_I2C0>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&i2c0_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c1: i2c@5002400 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002400 0x400>;
> +			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C1>;
> +			resets = <&ccu RST_BUS_I2C1>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c2: i2c@5002800 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002800 0x400>;
> +			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C2>;
> +			resets = <&ccu RST_BUS_I2C2>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c3: i2c@5002c00 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05002c00 0x400>;
> +			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C3>;
> +			resets = <&ccu RST_BUS_I2C3>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		i2c4: i2c@5003000 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x05003000 0x400>;
> +			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_I2C4>;
> +			resets = <&ccu RST_BUS_I2C4>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		spi0: spi@5010000 {
> +			compatible = "allwinner,sun50i-h616-spi",
> +				     "allwinner,sun8i-h3-spi";
> +			reg = <0x05010000 0x1000>;
> +			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> +			clock-names = "ahb", "mod";
> +			resets = <&ccu RST_BUS_SPI0>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&spi0_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		spi1: spi@5011000 {
> +			compatible = "allwinner,sun50i-h616-spi",
> +				     "allwinner,sun8i-h3-spi";
> +			reg = <0x05011000 0x1000>;
> +			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> +			clock-names = "ahb", "mod";
> +			resets = <&ccu RST_BUS_SPI1>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&spi1_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		emac0: ethernet@5020000 {
> +			compatible = "allwinner,sun50i-h616-emac",
> +				     "allwinner,sun50i-a64-emac";
> +			syscon = <&syscon>;
> +			reg = <0x05020000 0x10000>;
> +			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "macirq";
> +			resets = <&ccu RST_BUS_EMAC0>;
> +			reset-names = "stmmaceth";
> +			clocks = <&ccu CLK_BUS_EMAC0>;
> +			clock-names = "stmmaceth";
> +			status = "disabled";
> +
> +			mdio0: mdio {
> +				compatible = "snps,dwmac-mdio";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +
> +		rtc: rtc@7000000 {
> +			compatible = "allwinner,sun50i-h616-rtc";
> +			reg = <0x07000000 0x400>;
> +			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;

There's only one alarm and one interrupt documented: SPI 104

> +			clock-output-names = "osc32k", "osc32k-out", "iosc";
> +			#clock-cells = <1>;
> +		};
> +
> +		r_ccu: clock@7010000 {
> +			compatible = "allwinner,sun50i-h616-r-ccu";
> +			reg = <0x07010000 0x210>;
> +			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
> +				 <&ccu CLK_PLL_PERIPH0>;
> +			clock-names = "hosc", "losc", "iosc", "pll-periph";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		r_pio: pinctrl@7022000 {
> +			compatible = "allwinner,sun50i-h616-r-pinctrl";
> +			reg = <0x07022000 0x400>;
> +			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;

The H616 R_PIO has no interrupt capability.

> +			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
> +			clock-names = "apb", "hosc", "losc";
> +			gpio-controller;
> +			#gpio-cells = <3>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;

... so these properties don't belong here either.

> +			#address-cells = <0>;
> +
> +			r_i2c_pins: r-i2c-pins {
> +				pins = "PL0", "PL1";
> +				function = "s_i2c";
> +			};
> +
> +			r_rsb_pins: r-rsb-pins {
> +				pins = "PL0", "PL1";
> +				function = "s_rsb";
> +			};
> +		};
> +
> +		ir: ir@7040000 {
> +				compatible = "allwinner,sun50i-h616-ir",
> +					     "allwinner,sun6i-a31-ir";
> +				reg = <0x07040000 0x400>;
> +				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&r_ccu CLK_R_APB1_IR>,
> +					 <&r_ccu CLK_IR>;
> +				clock-names = "apb", "ir";
> +				resets = <&r_ccu RST_R_APB1_IR>;
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&ir_rx_pin>;
> +				status = "disabled";

You have an extra level of indentation here.

Regards,
Samuel

> +		};
> +
> +		r_i2c: i2c@7081400 {
> +			compatible = "allwinner,sun50i-h616-i2c",
> +				     "allwinner,sun6i-a31-i2c";
> +			reg = <0x07081400 0x400>;
> +			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&r_ccu CLK_R_APB2_I2C>;
> +			resets = <&r_ccu RST_R_APB2_I2C>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		r_rsb: rsb@7083000 {
> +			compatible = "allwinner,sun50i-h616-rsb",
> +				     "allwinner,sun8i-a23-rsb";
> +			reg = <0x07083000 0x400>;
> +			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&r_ccu CLK_R_APB2_RSB>;
> +			clock-frequency = <3000000>;
> +			resets = <&r_ccu RST_R_APB2_RSB>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&r_rsb_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +	};
> +};
> 

[PATCH v9 09/11] dt-bindings: arm: sunxi: Add two H616 board compatible strings

[Andre Przywara]

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 889128acf49a..1c557a736d86 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -848,6 +848,11 @@ properties:
           - const: yones-toptech,bs1078-v2
           - const: allwinner,sun6i-a31s
 
+      - description: X96 Mate TV box
+        items:
+          - const: hechuang,x96-mate
+          - const: allwinner,sun50i-h616
+
       - description: Xunlong OrangePi
         items:
           - const: xunlong,orangepi
@@ -948,4 +953,9 @@ properties:
           - const: xunlong,orangepi-zero-plus2-h3
           - const: allwinner,sun8i-h3
 
+      - description: Xunlong OrangePi Zero 2
+        items:
+          - const: xunlong,orangepi-zero2
+          - const: allwinner,sun50i-h616
+
 additionalProperties: true
-- 
2.17.6

[PATCH v9 10/11] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

[Andre Przywara]

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 512MiB/1GiB DDR3 DRAM
  - AXP305 PMIC
  - Raspberry-Pi-1 compatible GPIO header
  - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
  - 1 USB 2.0 host port
  - 1 USB 2.0 type C port (power supply + OTG)
  - MicroSD slot
  - on-board 2MiB bootable SPI NOR flash
  - 1Gbps Ethernet port (via RTL8211F PHY)
  - micro-HDMI port
  - unsupported Allwinner WiFi/BT chip

For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 204 ++++++++++++++++++
 2 files changed, 205 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index a96d9d2d8dd8..62f8d43cf84d 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -37,3 +37,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..0132c06be96a
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi Zero2";
+	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdce>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <0>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			reg_aldo2: aldo2 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+			};
+
+			reg_aldo3: aldo3 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			bldo2 {
+				/* unused */
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				/* reserved */
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&spi0  {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.17.6

[PATCH v9 11/11] arm64: dts: allwinner: h616: Add X96 Mate TV box support

[Andre Przywara]

The X96 Mate is an Allwinner H616 based TV box, featuring:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 2GiB/4GiB RAM (fully usable!)
  - 16/32/64GiB eMMC
  - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
  - Unsupported Allwinner WiFi chip
  - 2 x USB 2.0 host ports
  - HDMI port
  - IR receiver
  - 5V/2A DC power supply via barrel plug

For more information see: https://linux-sunxi.org/X96_Mate

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h616-x96-mate.dts    | 178 ++++++++++++++++++
 2 files changed, 179 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 62f8d43cf84d..14053c566601 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
new file mode 100644
index 000000000000..6334f4e20fd0
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2021 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "X96 Mate";
+	compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dcdce>;
+	vqmmc-supply = <&reg_bldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <0>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+				status = "disabled";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo3: aldo3 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+				status = "disabled";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_bldo2: bldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8-2";
+				status = "disabled";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc2v5";
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1360000>;
+				regulator-max-microvolt = <1360000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.17.6