[PATCH v2 3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support

Andre Przywara
2024-02-09T11:40:29Z

The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
- RTL8723BS WiFi & Bluetooth chip
- HDMI port
- two USB 2.0 ports
- 3.5mm AV port
- microSD card slot

The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.
The eMMC did not work with the MMC DDR speed mode, so this mode property
is omitted.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h64-remix-mini-pc.dts | 356 ++++++++++++++++++
2 files changed, 357 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 91d505b385de5..2db3b15ad09f2 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
new file mode 100644
index 0000000000000..b6e3c169797f0
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2023 ARM Ltd.
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+#include "sun50i-a64-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Remix Mini PC";
+ compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
+ "allwinner,sun50i-a64";
+
+ aliases {
+ ethernet1 = &rtl8723bs;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ reg_vcc5v: regulator-5v {
+ /* board wide 5V supply directly from the DC input */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&codec {
+ status = "okay";
+};
+
+&codec_analog {
+ cpvdd-supply = <&reg_eldo1>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu1 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu2 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu3 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&dai {
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <&reg_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+/* Connects to the AC200 chip */
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+};
+
+&i2c0_pins {
+ bias-pull-up;
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&reg_aldo1>;
+ vqmmc-supply = <&reg_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8723bs: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
+ vmmc-supply = <&reg_dcdc1>;
+ vqmmc-supply = <&reg_eldo1>;
+ bus-width = <8>;
+ non-removable;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pb-supply = <&reg_dcdc1>;
+ vcc-pc-supply = <&reg_dcdc1>;
+ vcc-pd-supply = <&reg_dcdc1>;
+ vcc-pe-supply = <&reg_dcdc1>;
+ vcc-pf-supply = <&reg_dcdc1>;
+ vcc-pg-supply = <&reg_dldo4>;
+ vcc-ph-supply = <&reg_dcdc1>;
+};
+
+&r_ir {
+ status = "okay";
+};
+
+&r_pio {
+ /*
+ * We cannot add that supply for now since it would create a circular
+ * dependency between pinctrl, the regulator and the RSB Bus.
+ *
+ * vcc-pl-supply = <&reg_aldo2>;
+ */
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en;
+
+ vin1-supply = <&reg_vcc5v>;
+ vin2-supply = <&reg_vcc5v>;
+ vin3-supply = <&reg_vcc5v>;
+ vin5-supply = <&reg_vcc5v>;
+ vin6-supply = <&reg_vcc5v>;
+ aldoin-supply = <&reg_vcc5v>;
+ dldoin-supply = <&reg_vcc5v>;
+ eldoin-supply = <&reg_vcc5v>;
+ fldoin-supply = <&reg_vcc5v>;
+ drivevbus-supply = <&reg_vcc5v>;
+ ips-supply = <&reg_vcc5v>;
+
+ status = "okay";
+ };
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&reg_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+/* Deviates from the reset default of 1.1V. */
+&reg_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd-sys";
+};
+
+&reg_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&reg_aldo2 {
+ /* Specifying R_PIO consumer would create circular dependency. */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+/* AC200 power supply */
+&reg_dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ave-33";
+};
+
+&reg_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+&reg_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&reg_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-cpvdd-dram-emmc";
+};
+
+/* Supplies the arisc management core, needed by TF-A to power off cores. */
+&reg_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+ vcc-hdmi-supply = <&reg_dcdc1>;
+};
+
+&sound {
+ simple-audio-card,aux-devs = <&codec_analog>;
+ simple-audio-card,widgets = "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Left DAC", "DACL",
+ "Right DAC", "DACR",
+ "Headphone Jack", "HP",
+ "ADCL", "Left ADC",
+ "ADCR", "Right ADC",
+ "MIC2", "Microphone Jack";
+ status = "okay";
+};
+
+/* On the (unpopulated) UART pads. */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8723bs-bt";
+ enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+ max-speed = <1500000>;
+ };
+};
+
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus-supply = <&reg_drivevbus>;
+ usb1_vbus-supply = <&reg_drivevbus>;
+ status = "okay";
+};
--
2.25.1