* [PATCH 45/47] adv7604: Add DT support [not found] <1391618558-5580-1-git-send-email-laurent.pinchart@ideasonboard.com> @ 2014-02-05 16:42 ` Laurent Pinchart 2014-02-11 9:23 ` Hans Verkuil 0 siblings, 1 reply; 6+ messages in thread From: Laurent Pinchart @ 2014-02-05 16:42 UTC (permalink / raw) To: linux-media; +Cc: Hans Verkuil, Lars-Peter Clausen, devicetree Parse the device tree node to populate platform data. Cc: devicetree@vger.kernel.org Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++ drivers/media/i2c/adv7604.c | 101 ++++++++++++++++++--- 2 files changed, 143 insertions(+), 14 deletions(-) create mode 100644 Documentation/devicetree/bindings/media/i2c/adv7604.txt diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode 100644 index 0000000..0845c50 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -0,0 +1,56 @@ +* Analog Devices ADV7604/11 video decoder with HDMI receiver + +The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input, +and the ADV7611 has one HDMI input and no analog input. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7604" for the ADV7604 + - "adi,adv7611" for the ADV7611 + + - reg: I2C slave address + + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug + detection pins, one per HDMI input. The active flag indicates the GPIO + level that enables hot-plug detection. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the device's reset pin. + + - adi,default-input: Index of the input to be configured as default. Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611. + + - adi,disable-power-down: Boolean property. When set forces the device to + ignore the power-down pin. The property is valid for the ADV7604 only as + the ADV7611 has no power-down pin. + + - adi,disable-cable-reset: Boolean property. When set disables the HDMI + receiver automatic reset when the HDMI cable is unplugged. + +Example: + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + + adi,default-input = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c index e586c1c..cd8a2dc 100644 --- a/drivers/media/i2c/adv7604.c +++ b/drivers/media/i2c/adv7604.c @@ -32,6 +32,7 @@ #include <linux/i2c.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/of_gpio.h> #include <linux/slab.h> #include <linux/v4l2-dv-timings.h> #include <linux/videodev2.h> @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info adv7604_chip_info[] = { }, }; +static struct i2c_device_id adv7604_i2c_id[] = { + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] }, + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] }, + { } +}; +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id); + +static struct of_device_id adv7604_of_id[] = { + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] }, + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] }, + { } +}; +MODULE_DEVICE_TABLE(of, adv7604_of_id); + +static int adv7604_parse_dt(struct adv7604_state *state) +{ + struct device_node *np; + unsigned int i; + int ret; + + np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node; + state->info = of_match_node(adv7604_of_id, np)->data; + + state->pdata.disable_pwrdnb = + of_property_read_bool(np, "adi,disable-power-down"); + state->pdata.disable_cable_det_rst = + of_property_read_bool(np, "adi,disable-cable-reset"); + + ret = of_property_read_u32(np, "adi,default-input", + &state->pdata.default_input); + if (ret < 0) + state->pdata.default_input = -1; + + for (i = 0; i < state->info->num_dv_ports; ++i) { + enum of_gpio_flags flags; + + state->pdata.hpd_gpio[i] = + of_get_named_gpio_flags(np, "hpd-gpios", i, &flags); + if (IS_ERR_VALUE(state->pdata.hpd_gpio[i])) + continue; + + state->pdata.hpd_gpio_low[i] = flags == OF_GPIO_ACTIVE_LOW; + } + + /* Disable the interrupt for now as no DT-based board uses it. */ + state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED; + + /* Use the default I2C addresses. */ + state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42; + state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40; + state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e; + state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38; + state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c; + state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26; + state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32; + state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36; + state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34; + state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30; + state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22; + state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24; + + /* HACK: Hardcode the remaining platform data fields. */ + state->pdata.blank_data = 1; + state->pdata.op_656_range = 1; + state->pdata.alt_data_sat = 1; + state->pdata.insert_av_codes = 1; + state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0; + + return 0; +} + static int adv7604_probe(struct i2c_client *client, const struct i2c_device_id *id) { static const struct v4l2_dv_timings cea640x480 = V4L2_DV_BT_CEA_640X480P59_94; struct adv7604_state *state; - struct adv7604_platform_data *pdata = client->dev.platform_data; struct v4l2_ctrl_handler *hdl; struct v4l2_subdev *sd; unsigned int i; @@ -2666,19 +2737,27 @@ static int adv7604_probe(struct i2c_client *client, return -ENOMEM; } - state->info = &adv7604_chip_info[id->driver_data]; state->i2c_clients[ADV7604_PAGE_IO] = client; /* initialize variables */ state->restart_stdi_once = true; state->selected_input = ~0; - /* platform data */ - if (!pdata) { + if (client->dev.of_node) { + err = adv7604_parse_dt(state); + if (err < 0) { + v4l_err(client, "DT parsing error\n"); + return err; + } + } else if (client->dev.platform_data) { + struct adv7604_platform_data *pdata = client->dev.platform_data; + + state->info = (const struct adv7604_chip_info *)id->driver_data; + state->pdata = *pdata; + } else { v4l_err(client, "No platform data!\n"); return -ENODEV; } - state->pdata = *pdata; /* Request GPIOs. */ for (i = 0; i < state->info->num_dv_ports; ++i) { @@ -2786,7 +2865,7 @@ static int adv7604_probe(struct i2c_client *client, continue; state->i2c_clients[i] = - adv7604_dummy_client(sd, pdata->i2c_addresses[i], + adv7604_dummy_client(sd, state->pdata.i2c_addresses[i], 0xf2 + i); if (state->i2c_clients[i] == NULL) { err = -ENOMEM; @@ -2860,21 +2939,15 @@ static int adv7604_remove(struct i2c_client *client) /* ----------------------------------------------------------------------- */ -static struct i2c_device_id adv7604_id[] = { - { "adv7604", ADV7604 }, - { "adv7611", ADV7611 }, - { } -}; -MODULE_DEVICE_TABLE(i2c, adv7604_id); - static struct i2c_driver adv7604_driver = { .driver = { .owner = THIS_MODULE, .name = "adv7604", + .of_match_table = of_match_ptr(adv7604_of_id), }, .probe = adv7604_probe, .remove = adv7604_remove, - .id_table = adv7604_id, + .id_table = adv7604_i2c_id, }; module_i2c_driver(adv7604_driver); -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 45/47] adv7604: Add DT support 2014-02-05 16:42 ` [PATCH 45/47] adv7604: Add DT support Laurent Pinchart @ 2014-02-11 9:23 ` Hans Verkuil 2014-02-11 12:08 ` Laurent Pinchart 0 siblings, 1 reply; 6+ messages in thread From: Hans Verkuil @ 2014-02-11 9:23 UTC (permalink / raw) To: Laurent Pinchart Cc: linux-media, Hans Verkuil, Lars-Peter Clausen, devicetree On 02/05/14 17:42, Laurent Pinchart wrote: > Parse the device tree node to populate platform data. > > Cc: devicetree@vger.kernel.org > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > --- > .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++ > drivers/media/i2c/adv7604.c | 101 ++++++++++++++++++--- > 2 files changed, 143 insertions(+), 14 deletions(-) > create mode 100644 Documentation/devicetree/bindings/media/i2c/adv7604.txt > > diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt > new file mode 100644 > index 0000000..0845c50 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt > @@ -0,0 +1,56 @@ > +* Analog Devices ADV7604/11 video decoder with HDMI receiver > + > +The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI > +receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input, > +and the ADV7611 has one HDMI input and no analog input. > + > +Required Properties: > + > + - compatible: Must contain one of the following > + - "adi,adv7604" for the ADV7604 > + - "adi,adv7611" for the ADV7611 > + > + - reg: I2C slave address > + > + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug > + detection pins, one per HDMI input. The active flag indicates the GPIO > + level that enables hot-plug detection. > + > +Optional Properties: > + > + - reset-gpios: Reference to the GPIO connected to the device's reset pin. > + > + - adi,default-input: Index of the input to be configured as default. Valid > + values are 0..5 for the ADV7604 and 0 for the ADV7611. > + > + - adi,disable-power-down: Boolean property. When set forces the device to > + ignore the power-down pin. The property is valid for the ADV7604 only as > + the ADV7611 has no power-down pin. > + > + - adi,disable-cable-reset: Boolean property. When set disables the HDMI > + receiver automatic reset when the HDMI cable is unplugged. > + > +Example: > + > + hdmi_receiver@4c { > + compatible = "adi,adv7611"; > + reg = <0x4c>; > + > + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; > + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; > + > + adi,default-input = <0>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + }; > + port@1 { > + reg = <1>; > + hdmi_in: endpoint { > + remote-endpoint = <&ccdc_in>; > + }; > + }; > + }; > diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c > index e586c1c..cd8a2dc 100644 > --- a/drivers/media/i2c/adv7604.c > +++ b/drivers/media/i2c/adv7604.c > @@ -32,6 +32,7 @@ > #include <linux/i2c.h> > #include <linux/kernel.h> > #include <linux/module.h> > +#include <linux/of_gpio.h> > #include <linux/slab.h> > #include <linux/v4l2-dv-timings.h> > #include <linux/videodev2.h> > @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info adv7604_chip_info[] = { > }, > }; > > +static struct i2c_device_id adv7604_i2c_id[] = { > + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] }, > + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id); > + > +static struct of_device_id adv7604_of_id[] = { > + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] }, > + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, adv7604_of_id); > + > +static int adv7604_parse_dt(struct adv7604_state *state) Put this under #ifdef CONFIG_OF. It fails to compile if CONFIG_OF is not set (as it is in my case since this driver is used with a PCIe card). Regards, Hans > +{ > + struct device_node *np; > + unsigned int i; > + int ret; > + > + np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node; > + state->info = of_match_node(adv7604_of_id, np)->data; > + > + state->pdata.disable_pwrdnb = > + of_property_read_bool(np, "adi,disable-power-down"); > + state->pdata.disable_cable_det_rst = > + of_property_read_bool(np, "adi,disable-cable-reset"); > + > + ret = of_property_read_u32(np, "adi,default-input", > + &state->pdata.default_input); > + if (ret < 0) > + state->pdata.default_input = -1; > + > + for (i = 0; i < state->info->num_dv_ports; ++i) { > + enum of_gpio_flags flags; > + > + state->pdata.hpd_gpio[i] = > + of_get_named_gpio_flags(np, "hpd-gpios", i, &flags); > + if (IS_ERR_VALUE(state->pdata.hpd_gpio[i])) > + continue; > + > + state->pdata.hpd_gpio_low[i] = flags == OF_GPIO_ACTIVE_LOW; > + } > + > + /* Disable the interrupt for now as no DT-based board uses it. */ > + state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED; > + > + /* Use the default I2C addresses. */ > + state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42; > + state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40; > + state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e; > + state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38; > + state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c; > + state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26; > + state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32; > + state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36; > + state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34; > + state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30; > + state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22; > + state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24; > + > + /* HACK: Hardcode the remaining platform data fields. */ > + state->pdata.blank_data = 1; > + state->pdata.op_656_range = 1; > + state->pdata.alt_data_sat = 1; > + state->pdata.insert_av_codes = 1; > + state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0; > + > + return 0; > +} > + > static int adv7604_probe(struct i2c_client *client, > const struct i2c_device_id *id) > { > static const struct v4l2_dv_timings cea640x480 = > V4L2_DV_BT_CEA_640X480P59_94; > struct adv7604_state *state; > - struct adv7604_platform_data *pdata = client->dev.platform_data; > struct v4l2_ctrl_handler *hdl; > struct v4l2_subdev *sd; > unsigned int i; > @@ -2666,19 +2737,27 @@ static int adv7604_probe(struct i2c_client *client, > return -ENOMEM; > } > > - state->info = &adv7604_chip_info[id->driver_data]; > state->i2c_clients[ADV7604_PAGE_IO] = client; > > /* initialize variables */ > state->restart_stdi_once = true; > state->selected_input = ~0; > > - /* platform data */ > - if (!pdata) { > + if (client->dev.of_node) { > + err = adv7604_parse_dt(state); > + if (err < 0) { > + v4l_err(client, "DT parsing error\n"); > + return err; > + } > + } else if (client->dev.platform_data) { > + struct adv7604_platform_data *pdata = client->dev.platform_data; > + > + state->info = (const struct adv7604_chip_info *)id->driver_data; > + state->pdata = *pdata; > + } else { > v4l_err(client, "No platform data!\n"); > return -ENODEV; > } > - state->pdata = *pdata; > > /* Request GPIOs. */ > for (i = 0; i < state->info->num_dv_ports; ++i) { > @@ -2786,7 +2865,7 @@ static int adv7604_probe(struct i2c_client *client, > continue; > > state->i2c_clients[i] = > - adv7604_dummy_client(sd, pdata->i2c_addresses[i], > + adv7604_dummy_client(sd, state->pdata.i2c_addresses[i], > 0xf2 + i); > if (state->i2c_clients[i] == NULL) { > err = -ENOMEM; > @@ -2860,21 +2939,15 @@ static int adv7604_remove(struct i2c_client *client) > > /* ----------------------------------------------------------------------- */ > > -static struct i2c_device_id adv7604_id[] = { > - { "adv7604", ADV7604 }, > - { "adv7611", ADV7611 }, > - { } > -}; > -MODULE_DEVICE_TABLE(i2c, adv7604_id); > - > static struct i2c_driver adv7604_driver = { > .driver = { > .owner = THIS_MODULE, > .name = "adv7604", > + .of_match_table = of_match_ptr(adv7604_of_id), > }, > .probe = adv7604_probe, > .remove = adv7604_remove, > - .id_table = adv7604_id, > + .id_table = adv7604_i2c_id, > }; > > module_i2c_driver(adv7604_driver); > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 45/47] adv7604: Add DT support 2014-02-11 9:23 ` Hans Verkuil @ 2014-02-11 12:08 ` Laurent Pinchart 2014-02-11 12:14 ` Hans Verkuil 0 siblings, 1 reply; 6+ messages in thread From: Laurent Pinchart @ 2014-02-11 12:08 UTC (permalink / raw) To: Hans Verkuil; +Cc: linux-media, Hans Verkuil, Lars-Peter Clausen, devicetree Hi Hans, On Tuesday 11 February 2014 10:23:03 Hans Verkuil wrote: > On 02/05/14 17:42, Laurent Pinchart wrote: > > Parse the device tree node to populate platform data. > > > > Cc: devicetree@vger.kernel.org > > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > --- > > > > .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++ > > drivers/media/i2c/adv7604.c | 101 ++++++++++++++-- > > 2 files changed, 143 insertions(+), 14 deletions(-) > > create mode 100644 > > Documentation/devicetree/bindings/media/i2c/adv7604.txt > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt > > b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode > > 100644 > > index 0000000..0845c50 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt > > @@ -0,0 +1,56 @@ > > +* Analog Devices ADV7604/11 video decoder with HDMI receiver > > + > > +The ADV7604 and ADV7611 are multiformat video decoders with an integrated > > HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one > > analog input, +and the ADV7611 has one HDMI input and no analog input. > > + > > +Required Properties: > > + > > + - compatible: Must contain one of the following > > + - "adi,adv7604" for the ADV7604 > > + - "adi,adv7611" for the ADV7611 > > + > > + - reg: I2C slave address > > + > > + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug > > + detection pins, one per HDMI input. The active flag indicates the > > GPIO > > + level that enables hot-plug detection. > > + > > +Optional Properties: > > + > > + - reset-gpios: Reference to the GPIO connected to the device's reset > > pin. + > > + - adi,default-input: Index of the input to be configured as default. > > Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611. > > + > > + - adi,disable-power-down: Boolean property. When set forces the device > > to + ignore the power-down pin. The property is valid for the ADV7604 > > only as + the ADV7611 has no power-down pin. > > + > > + - adi,disable-cable-reset: Boolean property. When set disables the HDMI > > + receiver automatic reset when the HDMI cable is unplugged. > > + > > +Example: > > + > > + hdmi_receiver@4c { > > + compatible = "adi,adv7611"; > > + reg = <0x4c>; > > + > > + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; > > + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; > > + > > + adi,default-input = <0>; > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@0 { > > + reg = <0>; > > + }; > > + port@1 { > > + reg = <1>; > > + hdmi_in: endpoint { > > + remote-endpoint = <&ccdc_in>; > > + }; > > + }; > > + }; > > diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c > > index e586c1c..cd8a2dc 100644 > > --- a/drivers/media/i2c/adv7604.c > > +++ b/drivers/media/i2c/adv7604.c > > @@ -32,6 +32,7 @@ > > > > #include <linux/i2c.h> > > #include <linux/kernel.h> > > #include <linux/module.h> > > > > +#include <linux/of_gpio.h> > > > > #include <linux/slab.h> > > #include <linux/v4l2-dv-timings.h> > > #include <linux/videodev2.h> > > > > @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info > > adv7604_chip_info[] = {> > > }, > > > > }; > > > > +static struct i2c_device_id adv7604_i2c_id[] = { > > + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] }, > > + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id); > > + > > +static struct of_device_id adv7604_of_id[] = { > > + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] }, > > + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(of, adv7604_of_id); > > + > > +static int adv7604_parse_dt(struct adv7604_state *state) > > Put this under #ifdef CONFIG_OF. #ifdef CONFIG_OF has been discouraged. I'll add an IS_ENABLED(CONFIG_OF) to condition the call of adv7604_parse_dt() and let the compiler optimize the function out, but I've been recommended to fix compilation errors instead of using conditional compilation. > It fails to compile if CONFIG_OF is not set (as it is in my case since this > driver is used with a PCIe card). What's the compilation failure ? > > +{ > > + struct device_node *np; > > + unsigned int i; > > + int ret; > > + > > + np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node; > > + state->info = of_match_node(adv7604_of_id, np)->data; > > + > > + state->pdata.disable_pwrdnb = > > + of_property_read_bool(np, "adi,disable-power-down"); > > + state->pdata.disable_cable_det_rst = > > + of_property_read_bool(np, "adi,disable-cable-reset"); > > + > > + ret = of_property_read_u32(np, "adi,default-input", > > + &state->pdata.default_input); > > + if (ret < 0) > > + state->pdata.default_input = -1; > > + > > + for (i = 0; i < state->info->num_dv_ports; ++i) { > > + enum of_gpio_flags flags; > > + > > + state->pdata.hpd_gpio[i] = > > + of_get_named_gpio_flags(np, "hpd-gpios", i, &flags); > > + if (IS_ERR_VALUE(state->pdata.hpd_gpio[i])) > > + continue; > > + > > + state->pdata.hpd_gpio_low[i] = flags == OF_GPIO_ACTIVE_LOW; > > + } > > + > > + /* Disable the interrupt for now as no DT-based board uses it. */ > > + state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED; > > + > > + /* Use the default I2C addresses. */ > > + state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42; > > + state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40; > > + state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e; > > + state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38; > > + state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c; > > + state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26; > > + state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32; > > + state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36; > > + state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34; > > + state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30; > > + state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22; > > + state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24; > > + > > + /* HACK: Hardcode the remaining platform data fields. */ > > + state->pdata.blank_data = 1; > > + state->pdata.op_656_range = 1; > > + state->pdata.alt_data_sat = 1; > > + state->pdata.insert_av_codes = 1; > > + state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0; > > + > > + return 0; > > +} -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 45/47] adv7604: Add DT support 2014-02-11 12:08 ` Laurent Pinchart @ 2014-02-11 12:14 ` Hans Verkuil 2014-02-11 12:21 ` Lars-Peter Clausen 0 siblings, 1 reply; 6+ messages in thread From: Hans Verkuil @ 2014-02-11 12:14 UTC (permalink / raw) To: Laurent Pinchart Cc: Hans Verkuil, linux-media, Hans Verkuil, Lars-Peter Clausen, devicetree On 02/11/14 13:08, Laurent Pinchart wrote: > Hi Hans, > > On Tuesday 11 February 2014 10:23:03 Hans Verkuil wrote: >> On 02/05/14 17:42, Laurent Pinchart wrote: >>> Parse the device tree node to populate platform data. >>> >>> Cc: devicetree@vger.kernel.org >>> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> >>> --- >>> >>> .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++ >>> drivers/media/i2c/adv7604.c | 101 ++++++++++++++-- >>> 2 files changed, 143 insertions(+), 14 deletions(-) >>> create mode 100644 >>> Documentation/devicetree/bindings/media/i2c/adv7604.txt >>> >>> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt >>> b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode >>> 100644 >>> index 0000000..0845c50 >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt >>> @@ -0,0 +1,56 @@ >>> +* Analog Devices ADV7604/11 video decoder with HDMI receiver >>> + >>> +The ADV7604 and ADV7611 are multiformat video decoders with an integrated >>> HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one >>> analog input, +and the ADV7611 has one HDMI input and no analog input. >>> + >>> +Required Properties: >>> + >>> + - compatible: Must contain one of the following >>> + - "adi,adv7604" for the ADV7604 >>> + - "adi,adv7611" for the ADV7611 >>> + >>> + - reg: I2C slave address >>> + >>> + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug >>> + detection pins, one per HDMI input. The active flag indicates the >>> GPIO >>> + level that enables hot-plug detection. >>> + >>> +Optional Properties: >>> + >>> + - reset-gpios: Reference to the GPIO connected to the device's reset >>> pin. + >>> + - adi,default-input: Index of the input to be configured as default. >>> Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611. >>> + >>> + - adi,disable-power-down: Boolean property. When set forces the device >>> to + ignore the power-down pin. The property is valid for the ADV7604 >>> only as + the ADV7611 has no power-down pin. >>> + >>> + - adi,disable-cable-reset: Boolean property. When set disables the HDMI >>> + receiver automatic reset when the HDMI cable is unplugged. >>> + >>> +Example: >>> + >>> + hdmi_receiver@4c { >>> + compatible = "adi,adv7611"; >>> + reg = <0x4c>; >>> + >>> + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; >>> + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; >>> + >>> + adi,default-input = <0>; >>> + >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + port@0 { >>> + reg = <0>; >>> + }; >>> + port@1 { >>> + reg = <1>; >>> + hdmi_in: endpoint { >>> + remote-endpoint = <&ccdc_in>; >>> + }; >>> + }; >>> + }; >>> diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c >>> index e586c1c..cd8a2dc 100644 >>> --- a/drivers/media/i2c/adv7604.c >>> +++ b/drivers/media/i2c/adv7604.c >>> @@ -32,6 +32,7 @@ >>> >>> #include <linux/i2c.h> >>> #include <linux/kernel.h> >>> #include <linux/module.h> >>> >>> +#include <linux/of_gpio.h> >>> >>> #include <linux/slab.h> >>> #include <linux/v4l2-dv-timings.h> >>> #include <linux/videodev2.h> >>> >>> @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info >>> adv7604_chip_info[] = {> >>> }, >>> >>> }; >>> >>> +static struct i2c_device_id adv7604_i2c_id[] = { >>> + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] }, >>> + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] }, >>> + { } >>> +}; >>> +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id); >>> + >>> +static struct of_device_id adv7604_of_id[] = { >>> + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] }, >>> + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] }, >>> + { } >>> +}; >>> +MODULE_DEVICE_TABLE(of, adv7604_of_id); >>> + >>> +static int adv7604_parse_dt(struct adv7604_state *state) >> >> Put this under #ifdef CONFIG_OF. > > #ifdef CONFIG_OF has been discouraged. I'll add an IS_ENABLED(CONFIG_OF) to > condition the call of adv7604_parse_dt() and let the compiler optimize the > function out, but I've been recommended to fix compilation errors instead of > using conditional compilation. > >> It fails to compile if CONFIG_OF is not set (as it is in my case since this >> driver is used with a PCIe card). > > What's the compilation failure ? drivers/media/i2c/adv7604.c: In function ‘adv7604_parse_dt’: drivers/media/i2c/adv7604.c:2671:48: warning: dereferencing ‘void *’ pointer [enabled by default] state->info = of_match_node(adv7604_of_id, np)->data; ^ drivers/media/i2c/adv7604.c:2671:48: error: request for member ‘data’ in something not a structure or union make[3]: *** [drivers/media/i2c/adv7604.o] Error 1 > >>> +{ >>> + struct device_node *np; >>> + unsigned int i; >>> + int ret; >>> + >>> + np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node; >>> + state->info = of_match_node(adv7604_of_id, np)->data; >>> + >>> + state->pdata.disable_pwrdnb = >>> + of_property_read_bool(np, "adi,disable-power-down"); >>> + state->pdata.disable_cable_det_rst = >>> + of_property_read_bool(np, "adi,disable-cable-reset"); >>> + >>> + ret = of_property_read_u32(np, "adi,default-input", >>> + &state->pdata.default_input); >>> + if (ret < 0) >>> + state->pdata.default_input = -1; >>> + >>> + for (i = 0; i < state->info->num_dv_ports; ++i) { >>> + enum of_gpio_flags flags; >>> + >>> + state->pdata.hpd_gpio[i] = >>> + of_get_named_gpio_flags(np, "hpd-gpios", i, &flags); >>> + if (IS_ERR_VALUE(state->pdata.hpd_gpio[i])) >>> + continue; >>> + >>> + state->pdata.hpd_gpio_low[i] = flags == OF_GPIO_ACTIVE_LOW; >>> + } >>> + >>> + /* Disable the interrupt for now as no DT-based board uses it. */ >>> + state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED; >>> + >>> + /* Use the default I2C addresses. */ >>> + state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22; >>> + state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24; >>> + >>> + /* HACK: Hardcode the remaining platform data fields. */ >>> + state->pdata.blank_data = 1; >>> + state->pdata.op_656_range = 1; >>> + state->pdata.alt_data_sat = 1; >>> + state->pdata.insert_av_codes = 1; >>> + state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0; >>> + >>> + return 0; >>> +} > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 45/47] adv7604: Add DT support 2014-02-11 12:14 ` Hans Verkuil @ 2014-02-11 12:21 ` Lars-Peter Clausen 2014-02-11 12:30 ` Laurent Pinchart 0 siblings, 1 reply; 6+ messages in thread From: Lars-Peter Clausen @ 2014-02-11 12:21 UTC (permalink / raw) To: Hans Verkuil Cc: Laurent Pinchart, Hans Verkuil, linux-media, Hans Verkuil, devicetree On 02/11/2014 01:14 PM, Hans Verkuil wrote: > > > On 02/11/14 13:08, Laurent Pinchart wrote: >> Hi Hans, >> >> On Tuesday 11 February 2014 10:23:03 Hans Verkuil wrote: >>> On 02/05/14 17:42, Laurent Pinchart wrote: >>>> Parse the device tree node to populate platform data. >>>> >>>> Cc: devicetree@vger.kernel.org >>>> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> >>>> --- >>>> >>>> .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++ >>>> drivers/media/i2c/adv7604.c | 101 ++++++++++++++-- >>>> 2 files changed, 143 insertions(+), 14 deletions(-) >>>> create mode 100644 >>>> Documentation/devicetree/bindings/media/i2c/adv7604.txt >>>> >>>> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt >>>> b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode >>>> 100644 >>>> index 0000000..0845c50 >>>> --- /dev/null >>>> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt >>>> @@ -0,0 +1,56 @@ >>>> +* Analog Devices ADV7604/11 video decoder with HDMI receiver >>>> + >>>> +The ADV7604 and ADV7611 are multiformat video decoders with an integrated >>>> HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one >>>> analog input, +and the ADV7611 has one HDMI input and no analog input. >>>> + >>>> +Required Properties: >>>> + >>>> + - compatible: Must contain one of the following >>>> + - "adi,adv7604" for the ADV7604 >>>> + - "adi,adv7611" for the ADV7611 >>>> + >>>> + - reg: I2C slave address >>>> + >>>> + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug >>>> + detection pins, one per HDMI input. The active flag indicates the >>>> GPIO >>>> + level that enables hot-plug detection. >>>> + >>>> +Optional Properties: >>>> + >>>> + - reset-gpios: Reference to the GPIO connected to the device's reset >>>> pin. + >>>> + - adi,default-input: Index of the input to be configured as default. >>>> Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611. >>>> + >>>> + - adi,disable-power-down: Boolean property. When set forces the device >>>> to + ignore the power-down pin. The property is valid for the ADV7604 >>>> only as + the ADV7611 has no power-down pin. >>>> + >>>> + - adi,disable-cable-reset: Boolean property. When set disables the HDMI >>>> + receiver automatic reset when the HDMI cable is unplugged. >>>> + >>>> +Example: >>>> + >>>> + hdmi_receiver@4c { >>>> + compatible = "adi,adv7611"; >>>> + reg = <0x4c>; >>>> + >>>> + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; >>>> + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; >>>> + >>>> + adi,default-input = <0>; >>>> + >>>> + #address-cells = <1>; >>>> + #size-cells = <0>; >>>> + >>>> + port@0 { >>>> + reg = <0>; >>>> + }; >>>> + port@1 { >>>> + reg = <1>; >>>> + hdmi_in: endpoint { >>>> + remote-endpoint = <&ccdc_in>; >>>> + }; >>>> + }; >>>> + }; >>>> diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c >>>> index e586c1c..cd8a2dc 100644 >>>> --- a/drivers/media/i2c/adv7604.c >>>> +++ b/drivers/media/i2c/adv7604.c >>>> @@ -32,6 +32,7 @@ >>>> >>>> #include <linux/i2c.h> >>>> #include <linux/kernel.h> >>>> #include <linux/module.h> >>>> >>>> +#include <linux/of_gpio.h> >>>> >>>> #include <linux/slab.h> >>>> #include <linux/v4l2-dv-timings.h> >>>> #include <linux/videodev2.h> >>>> >>>> @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info >>>> adv7604_chip_info[] = {> >>>> }, >>>> >>>> }; >>>> >>>> +static struct i2c_device_id adv7604_i2c_id[] = { >>>> + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] }, >>>> + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] }, >>>> + { } >>>> +}; >>>> +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id); >>>> + >>>> +static struct of_device_id adv7604_of_id[] = { >>>> + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] }, >>>> + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] }, >>>> + { } >>>> +}; >>>> +MODULE_DEVICE_TABLE(of, adv7604_of_id); >>>> + >>>> +static int adv7604_parse_dt(struct adv7604_state *state) >>> >>> Put this under #ifdef CONFIG_OF. >> >> #ifdef CONFIG_OF has been discouraged. I'll add an IS_ENABLED(CONFIG_OF) to >> condition the call of adv7604_parse_dt() and let the compiler optimize the >> function out, but I've been recommended to fix compilation errors instead of >> using conditional compilation. >> >>> It fails to compile if CONFIG_OF is not set (as it is in my case since this >>> driver is used with a PCIe card). >> >> What's the compilation failure ? > > drivers/media/i2c/adv7604.c: In function ‘adv7604_parse_dt’: > drivers/media/i2c/adv7604.c:2671:48: warning: dereferencing ‘void *’ pointer [enabled by default] > state->info = of_match_node(adv7604_of_id, np)->data; > ^ > drivers/media/i2c/adv7604.c:2671:48: error: request for member ‘data’ in something not a structure or union > make[3]: *** [drivers/media/i2c/adv7604.o] Error 1 That looks like a bug in the stubbed out version of of_match_node(). It should be a inline function with a return type, rather than a macro. - Lars ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 45/47] adv7604: Add DT support 2014-02-11 12:21 ` Lars-Peter Clausen @ 2014-02-11 12:30 ` Laurent Pinchart 0 siblings, 0 replies; 6+ messages in thread From: Laurent Pinchart @ 2014-02-11 12:30 UTC (permalink / raw) To: Lars-Peter Clausen Cc: Hans Verkuil, Hans Verkuil, linux-media, Hans Verkuil, devicetree Hi Lars, On Tuesday 11 February 2014 13:21:56 Lars-Peter Clausen wrote: > On 02/11/2014 01:14 PM, Hans Verkuil wrote: > > On 02/11/14 13:08, Laurent Pinchart wrote: > >> On Tuesday 11 February 2014 10:23:03 Hans Verkuil wrote: > >>> On 02/05/14 17:42, Laurent Pinchart wrote: > >>>> Parse the device tree node to populate platform data. > >>>> > >>>> Cc: devicetree@vger.kernel.org > >>>> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > >>>> --- > >>>> > >>>> .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++ > >>>> drivers/media/i2c/adv7604.c | 101 ++++++++++-- > >>>> 2 files changed, 143 insertions(+), 14 deletions(-) > >>>> create mode 100644 > >>>> Documentation/devicetree/bindings/media/i2c/adv7604.txt > >>>> > >>>> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt > >>>> b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode > >>>> 100644 > >>>> index 0000000..0845c50 > >>>> --- /dev/null > >>>> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt > >>>> @@ -0,0 +1,56 @@ > >>>> +* Analog Devices ADV7604/11 video decoder with HDMI receiver > >>>> + > >>>> +The ADV7604 and ADV7611 are multiformat video decoders with an > >>>> integrated > >>>> HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one > >>>> analog input, +and the ADV7611 has one HDMI input and no analog input. > >>>> + > >>>> +Required Properties: > >>>> + > >>>> + - compatible: Must contain one of the following > >>>> + - "adi,adv7604" for the ADV7604 > >>>> + - "adi,adv7611" for the ADV7611 > >>>> + > >>>> + - reg: I2C slave address > >>>> + > >>>> + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug > >>>> + detection pins, one per HDMI input. The active flag indicates the > >>>> GPIO > >>>> + level that enables hot-plug detection. > >>>> + > >>>> +Optional Properties: > >>>> + > >>>> + - reset-gpios: Reference to the GPIO connected to the device's reset > >>>> pin. + > >>>> + - adi,default-input: Index of the input to be configured as default. > >>>> Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611. > >>>> + > >>>> + - adi,disable-power-down: Boolean property. When set forces the > >>>> device > >>>> to + ignore the power-down pin. The property is valid for the > >>>> ADV7604 > >>>> only as + the ADV7611 has no power-down pin. > >>>> + > >>>> + - adi,disable-cable-reset: Boolean property. When set disables the > >>>> HDMI > >>>> + receiver automatic reset when the HDMI cable is unplugged. > >>>> + > >>>> +Example: > >>>> + > >>>> + hdmi_receiver@4c { > >>>> + compatible = "adi,adv7611"; > >>>> + reg = <0x4c>; > >>>> + > >>>> + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; > >>>> + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; > >>>> + > >>>> + adi,default-input = <0>; > >>>> + > >>>> + #address-cells = <1>; > >>>> + #size-cells = <0>; > >>>> + > >>>> + port@0 { > >>>> + reg = <0>; > >>>> + }; > >>>> + port@1 { > >>>> + reg = <1>; > >>>> + hdmi_in: endpoint { > >>>> + remote-endpoint = <&ccdc_in>; > >>>> + }; > >>>> + }; > >>>> + }; > >>>> diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c > >>>> index e586c1c..cd8a2dc 100644 > >>>> --- a/drivers/media/i2c/adv7604.c > >>>> +++ b/drivers/media/i2c/adv7604.c > >>>> @@ -32,6 +32,7 @@ > >>>> > >>>> #include <linux/i2c.h> > >>>> #include <linux/kernel.h> > >>>> #include <linux/module.h> > >>>> > >>>> +#include <linux/of_gpio.h> > >>>> > >>>> #include <linux/slab.h> > >>>> #include <linux/v4l2-dv-timings.h> > >>>> #include <linux/videodev2.h> > >>>> > >>>> @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info > >>>> adv7604_chip_info[] = {> > >>>> > >>>> }, > >>>> > >>>> }; > >>>> > >>>> +static struct i2c_device_id adv7604_i2c_id[] = { > >>>> + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] }, > >>>> + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] }, > >>>> + { } > >>>> +}; > >>>> +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id); > >>>> + > >>>> +static struct of_device_id adv7604_of_id[] = { > >>>> + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] }, > >>>> + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] }, > >>>> + { } > >>>> +}; > >>>> +MODULE_DEVICE_TABLE(of, adv7604_of_id); > >>>> + > >>>> +static int adv7604_parse_dt(struct adv7604_state *state) > >>> > >>> Put this under #ifdef CONFIG_OF. > >> > >> #ifdef CONFIG_OF has been discouraged. I'll add an IS_ENABLED(CONFIG_OF) > >> to condition the call of adv7604_parse_dt() and let the compiler optimize > >> the function out, but I've been recommended to fix compilation errors > >> instead of using conditional compilation. > >> > >>> It fails to compile if CONFIG_OF is not set (as it is in my case since > >>> this driver is used with a PCIe card). > >> > >> What's the compilation failure ? > > > > drivers/media/i2c/adv7604.c: In function ‘adv7604_parse_dt’: > > drivers/media/i2c/adv7604.c:2671:48: warning: dereferencing ‘void *’ > > pointer [enabled by default]> > > state->info = of_match_node(adv7604_of_id, np)->data; > > > > drivers/media/i2c/adv7604.c:2671:48: error: request for member ‘data’ in > > something not a structure or union make[3]: *** > > [drivers/media/i2c/adv7604.o] Error 1 > > That looks like a bug in the stubbed out version of of_match_node(). It > should be a inline function with a return type, rather than a macro. Indeed, I'll cook a patch up. -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-02-11 12:30 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1391618558-5580-1-git-send-email-laurent.pinchart@ideasonboard.com>
2014-02-05 16:42 ` [PATCH 45/47] adv7604: Add DT support Laurent Pinchart
2014-02-11 9:23 ` Hans Verkuil
2014-02-11 12:08 ` Laurent Pinchart
2014-02-11 12:14 ` Hans Verkuil
2014-02-11 12:21 ` Lars-Peter Clausen
2014-02-11 12:30 ` Laurent Pinchart
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).