Re: [PATCH 7/8] ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6

[Alexandre TORGUE <alexandre.torgue@foss.st.com>]

On 3/11/21 1:32 PM, dillon min wrote:
> Hi Alexandre
> 
> On Thu, Mar 11, 2021 at 6:42 PM Alexandre TORGUE
> <alexandre.torgue@foss.st.com> wrote:
>>
>>
>>
>> On 3/3/21 9:05 AM, dillon.minfei@gmail.com wrote:
>>> From: dillon min <dillon.minfei@gmail.com>
>>>
>>> This patchset has following changes:
>>>
>>> - add stm32h750i-art-pi.dtb
>>> - add dts binding usart3 for bt, uart4 for console
>>> - add dts binding sdmmc2 for wifi
>>> - add stm32h750-art-pi.dts to support art-pi board
>>>
>>> board component:
>>> - 8MiB qspi flash
>>> - 16MiB spi flash
>>> - 32MiB sdram
>>> - ap6212 wifi&bt&fm
>>>
>>> the detail board information can be found at:
>>> https://art-pi.gitee.io/website/
>>>
>>> Signed-off-by: dillon min <dillon.minfei@gmail.com>
>>> ---
>>>    arch/arm/boot/dts/Makefile              |   1 +
>>>    arch/arm/boot/dts/stm32h743.dtsi        |  30 +++++
>>>    arch/arm/boot/dts/stm32h750.dtsi        |   5 +
>>>    arch/arm/boot/dts/stm32h750i-art-pi.dts | 224 ++++++++++++++++++++++++++++++++
>>>    4 files changed, 260 insertions(+)
>>>    create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
>>>    create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index 8e5d4ab4e75e..a19c5ab9df84 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -1071,6 +1071,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
>>>        stm32746g-eval.dtb \
>>>        stm32h743i-eval.dtb \
>>>        stm32h743i-disco.dtb \
>>> +     stm32h750i-art-pi.dtb \
>>>        stm32mp153c-dhcom-drc02.dtb \
>>>        stm32mp157a-avenger96.dtb \
>>>        stm32mp157a-dhcor-avenger96.dtb \
>>> diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
>>> index 4ebffb0a45a3..981d44051007 100644
>>> --- a/arch/arm/boot/dts/stm32h743.dtsi
>>> +++ b/arch/arm/boot/dts/stm32h743.dtsi
>>> @@ -135,6 +135,22 @@
>>>                        clocks = <&rcc USART2_CK>;
>>>                };
>>>
>>> +             usart3: serial@40004800 {
>>> +                     compatible = "st,stm32h7-uart";
>>> +                     reg = <0x40004800 0x400>;
>>> +                     interrupts = <39>;
>>> +                     status = "disabled";
>>> +                     clocks = <&rcc USART3_CK>;
>>> +             };
>>> +
>>> +             uart4: serial@40004c00 {
>>> +                     compatible = "st,stm32h7-uart";
>>> +                     reg = <0x40004c00 0x400>;
>>> +                     interrupts = <52>;
>>> +                     status = "disabled";
>>> +                     clocks = <&rcc UART4_CK>;
>>> +             };
>>> +
>>
>> Those peripherals are available on h743 ?
> Yes, available for stm32h743, but might not used by stm32h743i-disco board.
> the difference between stm32h743xi and stm32h750xb:
>   flash size:  2048/128,
> ad convter : none/3
> crypto-hash: none/aes,hmac,....

Ok, so perfect.

> 
>>
>>>                i2c1: i2c@40005400 {
>>>                        compatible = "st,stm32f7-i2c";
>>>                        #address-cells = <1>;
>>> @@ -368,6 +384,20 @@
>>>                        max-frequency = <120000000>;
>>>                };
>>>
>>> +             sdmmc2: mmc@48022400 {
>>> +                     compatible = "arm,pl18x", "arm,primecell";
>>> +                     arm,primecell-periphid = <0x10153180>;
>>> +                     reg = <0x48022400 0x400>;
>>> +                     interrupts = <124>;
>>> +                     interrupt-names = "cmd_irq";
>>> +                     clocks = <&rcc SDMMC2_CK>;
>>> +                     clock-names = "apb_pclk";
>>> +                     resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
>>> +                     cap-sd-highspeed;
>>> +                     cap-mmc-highspeed;
>>> +                     max-frequency = <120000000>;
>>> +             };
>>> +
>>>                exti: interrupt-controller@58000000 {
>>>                        compatible = "st,stm32h7-exti";
>>>                        interrupt-controller;
>>> diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi
>>> new file mode 100644
>>> index 000000000000..dd9166223c2f
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32h750.dtsi
>>> @@ -0,0 +1,5 @@
>>> +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
>>> +/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
>>> +
>>> +#include "stm32h743.dtsi"
>>> +
>>> diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts
>>> new file mode 100644
>>> index 000000000000..84cf70d7800c
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
>>> @@ -0,0 +1,224 @@
>>> +/*
>>> + * Copyright 2021 - Dillon Min <dillon.minfei@gmail.com>
>>> + *
>>> + * This file is dual-licensed: you can use it either under the terms
>>> + * of the GPL or the X11 license, at your option. Note that this dual
>>> + * licensing only applies to this file, and not this project as a
>>> + * whole.
>>> + *
>>> + *  a) This file is free software; you can redistribute it and/or
>>> + *     modify it under the terms of the GNU General Public License as
>>> + *     published by the Free Software Foundation; either version 2 of the
>>> + *     License, or (at your option) any later version.
>>> + *
>>> + *     This file is distributed in the hope that it will be useful,
>>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>>> + *     GNU General Public License for more details.
>>> + *
>>> + * Or, alternatively,
>>> + *
>>> + *  b) Permission is hereby granted, free of charge, to any person
>>> + *     obtaining a copy of this software and associated documentation
>>> + *     files (the "Software"), to deal in the Software without
>>> + *     restriction, including without limitation the rights to use,
>>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>>> + *     sell copies of the Software, and to permit persons to whom the
>>> + *     Software is furnished to do so, subject to the following
>>> + *     conditions:
>>> + *
>>> + *     The above copyright notice and this permission notice shall be
>>> + *     included in all copies or substantial portions of the Software.
>>> + *
>>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>>> + *     OTHER DEALINGS IN THE SOFTWARE.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +#include "stm32h750.dtsi"
>>> +#include "stm32h750-pinctrl.dtsi"
>>> +#include <dt-bindings/interrupt-controller/irq.h>
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +
>>> +/ {
>>> +     model = "RT-Thread STM32H750i-ART-PI board";
>>> +     compatible = "st,stm32h750i-art-pi", "st,stm32h750";
>>> +
>>> +     chosen {
>>> +             bootargs = "root=/dev/ram";
>>> +             stdout-path = "serial0:2000000n8";
>>> +     };
>>> +
>>> +     memory@c0000000 {
>>> +             device_type = "memory";
>>> +             reg = <0xc0000000 0x2000000>;
>>> +     };
>>> +
>>> +     reserved-memory {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <1>;
>>> +             ranges;
>>> +
>>> +             linux,cma {
>>> +                     compatible = "shared-dma-pool";
>>> +                     no-map;
>>> +                     size = <0x100000>;
>>> +                     linux,dma-default;
>>> +             };
>>> +     };
>>> +
>>> +     aliases {
>>> +             serial0 = &uart4;
>>> +             serial1 = &usart3;
>>> +     };
>>> +
>>> +     leds {
>>> +             compatible = "gpio-leds";
>>> +             led-red {
>>> +                     gpios = <&gpioi 8 0>;
>>> +             };
>>> +             led-green {
>>> +                     gpios = <&gpioc 15 0>;
>>> +                     linux,default-trigger = "heartbeat";
>>> +             };
>>> +     };
>>> +
>>> +     v3v3: regulator-v3v3 {
>>> +             compatible = "regulator-fixed";
>>> +             regulator-name = "v3v3";
>>> +             regulator-min-microvolt = <3300000>;
>>> +             regulator-max-microvolt = <3300000>;
>>> +             regulator-always-on;
>>> +     };
>>> +
>>> +     wlan_pwr: regulator-wlan {
>>> +             compatible = "regulator-fixed";
>>> +
>>> +             regulator-name = "wl-reg";
>>> +             regulator-min-microvolt = <3300000>;
>>> +             regulator-max-microvolt = <3300000>;
>>> +
>>> +             gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
>>> +             enable-active-high;
>>> +     };
>>> +};
>>> +
>>> +&clk_hse {
>>> +     clock-frequency = <25000000>;
>>> +};
>>> +
>>> +&mac {
>>> +     status = "disabled";
>>> +     pinctrl-0       = <&ethernet_rmii>;
>>> +     pinctrl-names   = "default";
>>> +     phy-mode        = "rmii";
>>> +     phy-handle      = <&phy0>;
>>> +
>>> +     mdio0 {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <0>;
>>> +             compatible = "snps,dwmac-mdio";
>>> +             phy0: ethernet-phy@0 {
>>> +                     reg = <0>;
>>> +             };
>>> +     };
>>> +};
>>> +
>>> +&sdmmc1 {
>>> +     pinctrl-names = "default", "opendrain", "sleep";
>>> +     pinctrl-0 = <&sdmmc1_b4_pins_a>;
>>> +     pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>>> +     pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>>> +     broken-cd;
>>> +     st,neg-edge;
>>> +     bus-width = <4>;
>>> +     vmmc-supply = <&v3v3>;
>>> +     status = "okay";
>>> +};
>>> +
>>> +&usart2 {
>>> +     pinctrl-0 = <&usart2_pins>;
>>> +     pinctrl-names = "default";
>>> +     status = "disabled";
>>> +};
>>> +
>>> +&uart4 {
>>> +     pinctrl-0 = <&uart4_pins>;
>>> +     pinctrl-names = "default";
>>> +     status = "okay";
>>> +};
>>> +
>>> +&dma1 {
>>> +     status = "okay";
>>> +};
>>> +
>>
>> Would be better to order by name, but it is your board :)
> Okay, i will follow stm32f7/f4's order next submit.
>>
>>> +&dma2 {
>>> +     status = "okay";
>>> +};
>>> +
>>> +&spi1 {
>>> +     status = "okay";
>>> +     pinctrl-0 = <&spi1_pins>;
>>> +     pinctrl-names = "default";
>>> +     cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
>>> +     dmas = <&dmamux1 37 0x400 0x05>,
>>> +            <&dmamux1 38 0x400 0x05>;
>>> +     dma-names = "rx", "tx";
>>> +
>>> +     flash@0 {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <1>;
>>> +             compatible = "winbond,w25q128", "jedec,spi-nor";
>>> +             reg = <0>;
>>> +             spi-max-frequency = <80000000>;
>>> +
>>> +             partition@0 {
>>> +                     label = "root filesystem";
>>> +                     reg = <0 0x1000000>;
>>> +             };
>>> +     };
>>> +};
>>> +
>>> +&sdmmc2 {
>>> +     pinctrl-names = "default", "opendrain", "sleep";
>>> +     pinctrl-0 = <&sdmmc2_b4_pins_a>;
>>> +     pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
>>> +     pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
>>> +     broken-cd;
>>> +     non-removable;
>>> +     st,neg-edge;
>>> +     bus-width = <4>;
>>> +     vmmc-supply = <&wlan_pwr>;
>>> +     status = "okay";
>>> +
>>> +     #address-cells = <1>;
>>> +     #size-cells = <0>;
>>> +     brcmf: bcrmf@1 {
>>> +             reg = <1>;
>>> +             compatible = "brcm,bcm4329-fmac";
>>> +     };
>>> +};
>>> +
>>> +&usart3 {
>>> +     /delete-property/st,hw-flow-ctrl;
>>> +     cts-gpios = <&gpiod 11 GPIO_ACTIVE_LOW>;
>>> +     rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
>>> +     dmas = <&dmamux1 45 0x400 0x05>,
>>> +            <&dmamux1 46 0x400 0x05>;
>>> +     dma-names = "rx", "tx";
>>> +     status = "okay";
>>> +
>>> +     bluetooth {
>>> +             host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
>>> +             device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
>>> +             shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
>>> +             compatible = "brcm,bcm43438-bt";
>>> +             max-speed = <115200>;
>>> +     };
>>> +};
>>>