Re: [PATCH v2 3/3] dt-bindings: hwmon: Add bindings for max31732

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 14/12/2022 15:22, Sinan Divarci wrote:
> Adding bindings for max31732 quad remote temperature sensor

Full stop.

Subject: drop second, redundant "bindings for".

> 
> Signed-off-by: Sinan Divarci <Sinan.Divarci@analog.com>
> ---
>  .../bindings/hwmon/adi,max31732.yaml          | 83 +++++++++++++++++++
>  1 file changed, 83 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/adi,max31732.yaml
> 
> diff --git a/Documentation/devicetree/bindings/hwmon/adi,max31732.yaml b/Documentation/devicetree/bindings/hwmon/adi,max31732.yaml
> new file mode 100644
> index 000000000..c701cda95
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/adi,max31732.yaml
> @@ -0,0 +1,83 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright 2022 Analog Devices Inc.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/hwmon/adi,max31732.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices MAX31732 Temperature Sensor Device Driver

Drop "Device Driver"

> +
> +maintainers:
> +  - Sinan Divarci <Sinan.Divarci@analog.com>
> +
> +description: Bindings for the Analog Devices MAX31732 Temperature Sensor Device.

Drop "Bindings for". Actually, either drop entire description or write
something else than title.

> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,max31732
> +
> +  reg:
> +    description: I2C address of the Temperature Sensor Device.

Drop description.

> +    maxItems: 1
> +
> +  interrupts:
> +    minItems: 1
> +    maxItems: 2
> +
> +  interrupt-names:
> +    description: Name of the interrupt pin of max31732 used for IRQ.

Drop description.

> +    minItems: 1
> +    items:
> +      - enum: [ALARM1, ALARM2]
> +      - enum: [ALARM1, ALARM2]

This should be fixed, not flexible. Why it's flexible?

lowercase letters only

> +
> +  adi,alarm1-interrupt-mode:
> +    description: |
> +      Enables the ALARM1 output to function in interrupt mode.
> +      Default ALARM1 output function is comparator mode.

Why this is a property of DT/hardware? Don't encode policy in DT.

> +    type: boolean
> +
> +  adi,alarm2-interrupt-mode:
> +    description: |
> +      Enables the ALARM2 output to function in interrupt mode.
> +      Default ALARM2 output function is comparator mode.

Same question.

> +    type: boolean
> +
> +  adi,alarm1-fault-queue:
> +    description: The number of consecutive faults required to assert ALARM1.

Same question - why this number differs with hardware?

> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [1, 2, 4, 6]
> +    default: 1
> +
> +  adi,alarm2-fault-queue:
> +    description: The number of consecutive faults required to assert ALARM2.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [1, 2, 4, 6]
> +    default: 1
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/gpio/gpio.h>
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        sensor@1c {
> +            compatible = "adi,max31732";
> +            reg = <0x1c>;
> +            interrupt-parent = <&gpio>;
> +            interrupts = <17 IRQ_TYPE_EDGE_BOTH>, <27 IRQ_TYPE_EDGE_BOTH>;
> +            interrupt-names = "ALARM1", "ALARM2";
> +            adi,alarm1-fault-queue = <4>;
> +            adi,alarm2-fault-queue = <2>;
> +            adi,alarm2-interrupt-mode;
> +      };

Messed indentation.


> +    };

Best regards,
Krzysztof