[PATCH 0/3] Add R8A77980/Condor/V3HSK GPIO support

[PATCH 0/3] Add R8A77980/Condor/V3HSK GPIO support

[Sergei Shtylyov]

Hello!

Here's the set of 3 patches against Simon Horman's 'renesas.git' repo's
'renesas-devel-20180529-v4.17-rc7' tag plus the I2C patches reposted yesterday.
We're adding the R8A77980 GPIO nodes and then describing the PHY IRQ for the
GEther/EtherAVB devices declared earlier.

[1/3] arm64: dts: renesas: r8a77980: add GPIO support
[2/3] arm64: dts: renesas: condor: specify EtherAVB PHY IRQ
[3/3] arm64: dts: renesas: v3hsk: specify GEther PHY IRQ

WBR, Sergei

[PATCH 1/3] arm64: dts: renesas: r8a77980: add GPIO support

[Sergei Shtylyov]

Describe all 6 GPIO controllers in the R8A77980 device tree.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

---
 arch/arm64/boot/dts/renesas/r8a77980.dtsi |   90 ++++++++++++++++++++++++++++++
 1 file changed, 90 insertions(+)

Index: renesas/arch/arm64/boot/dts/renesas/r8a77980.dtsi
===================================================================
--- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980.dtsi
+++ renesas/arch/arm64/boot/dts/renesas/r8a77980.dtsi
@@ -118,6 +118,96 @@
 		#size-cells = <2>;
 		ranges;
 
+		gpio0: gpio@e6050000 {
+			compatible = "renesas,gpio-r8a77980",
+				     "renesas,rcar-gen3-gpio";
+			reg = <0 0xe6050000 0 0x50>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 0 22>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 912>;
+			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+			resets = <&cpg 912>;
+		};
+
+		gpio1: gpio@e6051000 {
+			compatible = "renesas,gpio-r8a77980",
+				     "renesas,rcar-gen3-gpio";
+			reg = <0 0xe6051000 0 0x50>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 32 28>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 911>;
+			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+			resets = <&cpg 911>;
+		};
+
+		gpio2: gpio@e6052000 {
+			compatible = "renesas,gpio-r8a77980",
+				     "renesas,rcar-gen3-gpio";
+			reg = <0 0xe6052000 0 0x50>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 64 30>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 910>;
+			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+			resets = <&cpg 910>;
+		};
+
+		gpio3: gpio@e6053000 {
+			compatible = "renesas,gpio-r8a77980",
+				     "renesas,rcar-gen3-gpio";
+			reg = <0 0xe6053000 0 0x50>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 96 17>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 909>;
+			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+			resets = <&cpg 909>;
+		};
+
+		gpio4: gpio@e6054000 {
+			compatible = "renesas,gpio-r8a77980",
+				     "renesas,rcar-gen3-gpio";
+			reg = <0 0xe6054000 0 0x50>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 128 25>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 908>;
+			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+			resets = <&cpg 908>;
+		};
+
+		gpio5: gpio@e6055000 {
+			compatible = "renesas,gpio-r8a77980",
+				     "renesas,rcar-gen3-gpio";
+			reg = <0 0xe6055000 0 0x50>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 160 15>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 907>;
+			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
+			resets = <&cpg 907>;
+		};
+
 		pfc: pin-controller@e6060000 {
 			compatible = "renesas,pfc-r8a77980";
 			reg = <0 0xe6060000 0 0x50c>;

Re: [PATCH 1/3] arm64: dts: renesas: r8a77980: add GPIO support

[Simon Horman]

On Fri, Jun 01, 2018 at 11:44:46PM +0300, Sergei Shtylyov wrote:
> Describe all 6 GPIO controllers in the R8A77980 device tree.
> 
> Based on the original (and large) patch by Vladimir Barinov.
> 
> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

This looks fine but I will wait to see if there are other reviews before
applying.

Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

Re: [PATCH 1/3] arm64: dts: renesas: r8a77980: add GPIO support

[Geert Uytterhoeven]

On Fri, Jun 1, 2018 at 10:44 PM, Sergei Shtylyov
<sergei.shtylyov@cogentembedded.com> wrote:
> Describe all 6 GPIO controllers in the R8A77980 device tree.
>
> Based on the original (and large) patch by Vladimir Barinov.
>
> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH 1/3] arm64: dts: renesas: r8a77980: add GPIO support

[Simon Horman]

On Wed, Jun 06, 2018 at 11:07:27AM +0200, Geert Uytterhoeven wrote:
> On Fri, Jun 1, 2018 at 10:44 PM, Sergei Shtylyov
> <sergei.shtylyov@cogentembedded.com> wrote:
> > Describe all 6 GPIO controllers in the R8A77980 device tree.
> >
> > Based on the original (and large) patch by Vladimir Barinov.
> >
> > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> 
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Thanks Sergei, applied.

[PATCH 2/3] arm64: dts: renesas: condor: specify EtherAVB PHY IRQ

[Sergei Shtylyov]

Specify EtherAVB PHY IRQ in the Condor board's device tree, now that
we have the GPIO support (previously phylib had to resort to polling).

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

---
 arch/arm64/boot/dts/renesas/r8a77980-condor.dts |    2 ++
 1 file changed, 2 insertions(+)

Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
===================================================================
--- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -59,6 +59,8 @@
 	phy0: ethernet-phy@0 {
 		rxc-skew-ps = <1500>;
 		reg = <0>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
 	};
 };

Re: [PATCH 2/3] arm64: dts: renesas: condor: specify EtherAVB PHY IRQ

[Simon Horman]

On Fri, Jun 01, 2018 at 11:45:55PM +0300, Sergei Shtylyov wrote:
> Specify EtherAVB PHY IRQ in the Condor board's device tree, now that
> we have the GPIO support (previously phylib had to resort to polling).
> 
> Based on the original (and large) patch by Vladimir Barinov.
> 
> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> 
> ---
>  arch/arm64/boot/dts/renesas/r8a77980-condor.dts |    2 ++
>  1 file changed, 2 insertions(+)
> 
> Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
> ===================================================================
> --- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
> +++ renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
> @@ -59,6 +59,8 @@
>  	phy0: ethernet-phy@0 {
>  		rxc-skew-ps = <1500>;
>  		reg = <0>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;

I don't see this documented. Perhaps I'm missing something obvious.
Or you have some extra information or newer documentation?

Also, given Olof Johansson's recent comments in ("Re: [GIT PULL] Renesas
ARM64 Based SoC DT Updates for v4.18") please consider squashing this patch
and the following one.

>  	};
>  };
>  
> 

Re: [PATCH 2/3] arm64: dts: renesas: condor: specify EtherAVB PHY IRQ

[Sergei Shtylyov]

On 06/04/2018 01:33 PM, Simon Horman wrote:

>> Specify EtherAVB PHY IRQ in the Condor board's device tree, now that
>> we have the GPIO support (previously phylib had to resort to polling).
>>
>> Based on the original (and large) patch by Vladimir Barinov.
>>
>> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
>>
>> ---
>>  arch/arm64/boot/dts/renesas/r8a77980-condor.dts |    2 ++
>>  1 file changed, 2 insertions(+)
>>
>> Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
>> ===================================================================
>> --- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
>> +++ renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
>> @@ -59,6 +59,8 @@
>>  	phy0: ethernet-phy@0 {
>>  		rxc-skew-ps = <1500>;
>>  		reg = <0>;
>> +		interrupt-parent = <&gpio1>;
>> +		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
> 
> I don't see this documented. Perhaps I'm missing something obvious.

   Have you looked into the V3H PFC section for where in the GPSRs AVB_PHY_INT
is mapped?
   The Condor schematics doesn't explicitly list the GPIO for AVB_PHY_INT
because that signal is meant to be routed thru the MAC. Unfortunately, the
sh_eth/ravb drivers don't support the PHY interrupt (the phylib function,
phy_mac_interrupt() reporting the PHY interrupts routed thru MAC is clearly
inadequate as it wants the link state as an argument), so we have to resort
to the GPIO interrupts...

> Or you have some extra information or newer documentation?

   No.

> Also, given Olof Johansson's recent comments in ("Re: [GIT PULL] Renesas
> ARM64 Based SoC DT Updates for v4.18") please consider squashing this patch
> and the following one.

   Hm... note that the different Ether cores are involved in these 2 PHY IRQ
patches. If that's OK, I can merge the patches...

[...]

MBR< Sergei

Re: [PATCH 2/3] arm64: dts: renesas: condor: specify EtherAVB PHY IRQ

[Simon Horman]

On Mon, Jun 04, 2018 at 05:22:52PM +0300, Sergei Shtylyov wrote:
> On 06/04/2018 01:33 PM, Simon Horman wrote:
> 
> >> Specify EtherAVB PHY IRQ in the Condor board's device tree, now that
> >> we have the GPIO support (previously phylib had to resort to polling).
> >>
> >> Based on the original (and large) patch by Vladimir Barinov.
> >>
> >> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> >> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> >>
> >> ---
> >>  arch/arm64/boot/dts/renesas/r8a77980-condor.dts |    2 ++
> >>  1 file changed, 2 insertions(+)
> >>
> >> Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
> >> ===================================================================
> >> --- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
> >> +++ renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
> >> @@ -59,6 +59,8 @@
> >>  	phy0: ethernet-phy@0 {
> >>  		rxc-skew-ps = <1500>;
> >>  		reg = <0>;
> >> +		interrupt-parent = <&gpio1>;
> >> +		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
> > 
> > I don't see this documented. Perhaps I'm missing something obvious.
> 
>    Have you looked into the V3H PFC section for where in the GPSRs AVB_PHY_INT
> is mapped?

Thanks, I see that now.

>    The Condor schematics doesn't explicitly list the GPIO for AVB_PHY_INT
> because that signal is meant to be routed thru the MAC. Unfortunately, the
> sh_eth/ravb drivers don't support the PHY interrupt (the phylib function,
> phy_mac_interrupt() reporting the PHY interrupts routed thru MAC is clearly
> inadequate as it wants the link state as an argument), so we have to resort
> to the GPIO interrupts...

Understood.

> > Or you have some extra information or newer documentation?
> 
>    No.
> 
> > Also, given Olof Johansson's recent comments in ("Re: [GIT PULL] Renesas
> > ARM64 Based SoC DT Updates for v4.18") please consider squashing this patch
> > and the following one.
> 
>    Hm... note that the different Ether cores are involved in these 2 PHY IRQ
> patches. If that's OK, I can merge the patches...

Tough call. Functionally these are both ethernet even though they are
different IP cores. So I think I prefer a squash.

I have applied 1/3 of this series and will push shortly.

[PATCH 3/3] arm64: dts: renesas: v3hsk: specify GEther PHY IRQ

[Sergei Shtylyov]

Specify GEther PHY IRQ in the V3H Starter Kit board's device tree, now
that we have the GPIO support (previously phylib had to resort to polling).

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

---
 arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts |    2 ++
 1 file changed, 2 insertions(+)

Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
===================================================================
--- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
+++ renesas/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
@@ -48,6 +48,8 @@
 
 	phy0: ethernet-phy@0 {
 		reg = <0>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 	};
 };

Re: [PATCH 3/3] arm64: dts: renesas: v3hsk: specify GEther PHY IRQ

[Simon Horman]

On Fri, Jun 01, 2018 at 11:47:14PM +0300, Sergei Shtylyov wrote:
> Specify GEther PHY IRQ in the V3H Starter Kit board's device tree, now
> that we have the GPIO support (previously phylib had to resort to polling).
> 
> Based on the original (and large) patch by Vladimir Barinov.
> 
> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Given Olof Johansson's recent comments in ("Re: [GIT PULL] Renesas      
ARM64 Based SoC DT Updates for v4.18") please consider squashing this patch
and the previous one.

Other than that, this patch looks good to me.

Re: [PATCH 3/3] arm64: dts: renesas: v3hsk: specify GEther PHY IRQ

[Geert Uytterhoeven]

On Fri, Jun 1, 2018 at 10:47 PM, Sergei Shtylyov
<sergei.shtylyov@cogentembedded.com> wrote:
> Specify GEther PHY IRQ in the V3H Starter Kit board's device tree, now
> that we have the GPIO support (previously phylib had to resort to polling).
>
> Based on the original (and large) patch by Vladimir Barinov.
>
> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH v2] arm64: dts: renesas: condor/v3hsk: specify Ethernet PHY IRQs

[Sergei Shtylyov]

Specify Ethernet PHY IRQs in the Condor/V3HSK board device trees, now that
we have the GPIO support (previously phylib had  to resort to polling).

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

---
Changes in version 2:
- merged in the analogous V3HSK patch, renamed the patch, and updated the
  patch description accordingly.

 arch/arm64/boot/dts/renesas/r8a77980-condor.dts |    2 ++
 arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts  |    2 ++
 2 files changed, 4 insertions(+)

Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
===================================================================
--- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -59,6 +59,8 @@
 	phy0: ethernet-phy@0 {
 		rxc-skew-ps = <1500>;
 		reg = <0>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
===================================================================
--- renesas.orig/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
+++ renesas/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
@@ -48,6 +48,8 @@
 
 	phy0: ethernet-phy@0 {
 		reg = <0>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 	};
 };

Re: [PATCH v2] arm64: dts: renesas: condor/v3hsk: specify Ethernet PHY IRQs

[Sergei Shtylyov]

On 06/13/2018 07:42 PM, Sergei Shtylyov wrote:

> Specify Ethernet PHY IRQs in the Condor/V3HSK board device trees, now that
> we have the GPIO support (previously phylib had  to resort to polling).
> 
> Based on the original (and large) patch by Vladimir Barinov.
> 
> Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> 
> ---

   Forgot to add the the patch is against the 'renesas-devel-20180613-v4.17' tag.

[...]

MBR, Sergei

Re: [PATCH v2] arm64: dts: renesas: condor/v3hsk: specify Ethernet PHY IRQs

[Simon Horman]

On Wed, Jun 13, 2018 at 07:44:02PM +0300, Sergei Shtylyov wrote:
> On 06/13/2018 07:42 PM, Sergei Shtylyov wrote:
> 
> > Specify Ethernet PHY IRQs in the Condor/V3HSK board device trees, now that
> > we have the GPIO support (previously phylib had  to resort to polling).
> > 
> > Based on the original (and large) patch by Vladimir Barinov.
> > 
> > Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
> > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> > 
> > ---
> 
>    Forgot to add the the patch is against the 'renesas-devel-20180613-v4.17' tag.
> 

Thanks Sergei, applied.