[PATCH 0/2] arm64: dts: rockchip: Add Hardkernel ODROID-M2

[PATCH 0/2] arm64: dts: rockchip: Add Hardkernel ODROID-M2

[Jonas Karlman]

This series add initial support for the Hardkernel ODROID-M2 board.

The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.

Schematics for ODROID-M2 can be found at:
https://wiki.odroid.com/_media/odroid-m2/hardware/m2_main_rev1.0_240611.pdf

The device tree was created based on the schematics with regulator
voltage values adjusted to closer match vendor downstream device tree.

Testing was done booting into Linux using mainline U-Boot from [1],
a test build of mainline U-Boot for ODROID-M2 can be found at [2].

U-Boot patches will be sent once DT reach the devicetree-rebasing tree.

[1] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3xxx-2024.10/
[2] https://github.com/Kwiboo/u-boot-build/actions/runs/10653436524

Jonas Karlman (2):
  dt-bindings: arm: rockchip: Add Hardkernel ODROID-M2
  arm64: dts: rockchip: Add Hardkernel ODROID-M2

 .../devicetree/bindings/arm/rockchip.yaml     |   5 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3588s-odroid-m2.dts   | 903 ++++++++++++++++++
 3 files changed, 909 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dts

-- 
2.46.0

[PATCH 1/2] dt-bindings: arm: rockchip: Add Hardkernel ODROID-M2

[Jonas Karlman]

The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.

Add devicetree binding documentation for the Hardkernel ODROID-M2 board.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 0c810037200d..ff9f2f529beb 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -605,6 +605,11 @@ properties:
           - const: hardkernel,odroid-m1s
           - const: rockchip,rk3566
 
+      - description: Hardkernel Odroid M2
+        items:
+          - const: hardkernel,odroid-m2
+          - const: rockchip,rk3588s
+
       - description: Hugsun X99 TV Box
         items:
           - const: hugsun,x99
-- 
2.46.0

[PATCH 2/2] arm64: dts: rockchip: Add Hardkernel ODROID-M2

[Jonas Karlman]

The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.

Add initial support for eMMC, SD-card, Ethernet, PCIe and USB.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3588s-odroid-m2.dts   | 903 ++++++++++++++++++
 2 files changed, 904 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 60dce56892d0..6e054e580928 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -151,4 +151,5 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dts b/arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dts
new file mode 100644
index 000000000000..63d91236ba9f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dts
@@ -0,0 +1,903 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3588s.dtsi"
+
+/ {
+	model = "Hardkernel ODROID-M2";
+	compatible = "hardkernel,odroid-m2", "rockchip,rk3588s";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_led>, <&sys_led>;
+
+		led_pwr: led-0 {
+			color = <LED_COLOR_ID_RED>;
+			default-state = "on";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led_sys: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			default-state = "on";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	fan: pwm-fan {
+		compatible = "pwm-fan";
+		#cooling-cells = <2>;
+		cooling-levels = <0 192 224 255>;
+		fan-supply = <&vcc5v0_sys>;
+		pwms = <&pwm0 0 22222 0>;
+	};
+
+	vcc_1v1_nldo_s3: regulator-1v1-vcc-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v1_nldo_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc4v0_sys>;
+	};
+
+	vcc3v3_lcd: regulator-3v3-vcc-lcd {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwren>;
+		regulator-name = "vcc3v3_lcd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc3v3_pcie: regulator-3v3-vcc-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pwren>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc_3v3_s0: regulator-3v3-vcc-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc4v0_sys: regulator-4v0-vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc4v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <4800000>;
+		regulator-max-microvolt = <4800000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_sys: regulator-5v0-vcc-sys {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_pwren>;
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb2_host: regulator-5v0-vcc-usb2-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_host_pwren>;
+		regulator-name = "vcc5v0_usb2_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb3_host: regulator-5v0-vcc-usb3-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_host_pwren>;
+		regulator-name = "vcc5v0_usb3_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb3_typec: regulator-5v0-vcc-usb3-typec {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_typec_pwren>;
+		regulator-name = "vcc5v0_usb3_typec";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcca: regulator-5v0-vcca {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc12v_dcin: regulator-12v0-vcc-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+};
+
+&combphy0_ps {
+	status = "okay";
+};
+
+&combphy2_psu {
+	status = "okay";
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gmac1 {
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&vcc_3v3_s0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_miim
+		     &gmac1_tx_bus2
+		     &gmac1_rx_bus2
+		     &gmac1_rgmii_clk
+		     &gmac1_rgmii_bus
+		     &gmac1_clkinout>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0m2_xfer>;
+	status = "okay";
+
+	vdd_cpu_big0_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc4v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: regulator@43 {
+		compatible = "rockchip,rk8603", "rockchip,rk8602";
+		reg = <0x43>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc4v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	vdd_npu_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_npu_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <950000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc4v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c8m2_xfer>;
+	status = "okay";
+
+	usbc0: usb-typec@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usbc0_int>;
+		vbus-supply = <&vcc5v0_usb3_typec>;
+
+		connector {
+			compatible = "usb-c-connector";
+			data-role = "dual";
+			label = "USB-C";
+			op-sink-microwatt = <1000000>;
+			power-role = "dual";
+			sink-pdos = <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			try-power-role = "source";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usbc0_role_switch: endpoint {
+						remote-endpoint = <&usb_host0_xhci_role_switch>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usbc0_orientation_switch: endpoint {
+						remote-endpoint = <&usbdp_phy0_orientation_switch>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usbc0_dp_altmode_mux: endpoint {
+						remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcf8563_int>;
+		wakeup-source;
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id001c.c916";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&package_thermal {
+	polling-delay = <1000>;
+
+	trips {
+		package_fan0: package-fan0 {
+			hysteresis = <2000>;
+			temperature = <60000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map0 {
+			cooling-device = <&fan 1 THERMAL_NO_LIMIT>;
+			trip = <&package_fan0>;
+		};
+	};
+};
+
+&pcie2x1l2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_pins>;
+	reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pinctrl {
+	lcd {
+		lcd_pwren: lcd-pwren {
+			rockchip,pins = <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		pwr_led: pwr-led {
+			rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		sys_led: sys-led {
+			rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie20x1_pins: pcie20x1-pins {
+			rockchip,pins =
+				<1 RK_PA0 4 &pcfg_pull_none>,
+				<1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>,
+				<1 RK_PA1 4 &pcfg_pull_none>;
+		};
+
+		pcie_pwren: pcie-pwren {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	regulator {
+		vcc5v0_pwren: vcc5v0-pwren {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	rtc {
+		pcf8563_int: pcf8563-int {
+			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		usb2_host_pwren: usb2-host-pwren {
+			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usb3_host_pwren: usb3-host-pwren {
+			rockchip,pins = <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usb3_typec_pwren: usb3-typec-pwren {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usbc0_int: usbc0-int {
+			rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0m2_pins>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8_s0>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	no-sd;
+	no-sdio;
+	non-removable;
+	vmmc-supply = <&vcc_3v3_s0>;
+	vqmmc-supply = <&vcc_1v8_s0>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	no-mmc;
+	no-sdio;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&spi2 {
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2m2_cs0>, <&spi2m2_pins>;
+	status = "okay";
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		reg = <0x0>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		spi-max-frequency = <1000000>;
+		system-power-controller;
+
+		vcc1-supply = <&vcc4v0_sys>;
+		vcc2-supply = <&vcc4v0_sys>;
+		vcc3-supply = <&vcc4v0_sys>;
+		vcc4-supply = <&vcc4v0_sys>;
+		vcc5-supply = <&vcc4v0_sys>;
+		vcc6-supply = <&vcc4v0_sys>;
+		vcc7-supply = <&vcc4v0_sys>;
+		vcc8-supply = <&vcc4v0_sys>;
+		vcc9-supply = <&vcc4v0_sys>;
+		vcc10-supply = <&vcc4v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc4v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcca>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: dcdc-reg1 {
+				regulator-name = "vdd_gpu_s0";
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-enable-ramp-delay = <400>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg2 {
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_logic_s0: dcdc-reg3 {
+				regulator-name = "vdd_logic_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <750000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_vdenc_s0: dcdc-reg4 {
+				regulator-name = "vdd_vdenc_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg5 {
+				regulator-name = "vdd_ddr_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-name = "vdd2_ddr_s3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-name = "vdd_2v0_pldo_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-name = "vcc_3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg9 {
+				regulator-name = "vddq_ddr_s0";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg10 {
+				regulator-name = "vcc_1v8_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_1v8_s0: pldo-reg1 {
+				regulator-name = "vcc_1v8_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8_s0: pldo-reg2 {
+				regulator-name = "vcca_1v8_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-name = "vdda_1v2_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-name = "vcca_3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-name = "vccio_sd_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3_pldo6: pldo-reg6 {
+				regulator-name = "vcc_1v8_s3_pldo6";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-name = "vdd_0v75_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-name = "vdda_ddr_pll_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdda_0v75_s0: nldo-reg3 {
+				regulator-name = "vdda_0v75_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <837500>;
+				regulator-max-microvolt = <837500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-name = "vdda_0v85_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* Schematics show not in use */
+			nldo-reg5 {
+			};
+		};
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	status = "okay";
+};
+
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_usb2_host>;
+	status = "okay";
+};
+
+&u2phy3 {
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_usb3_host>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2m0_xfer>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usb_host0_xhci_role_switch: endpoint {
+			remote-endpoint = <&usbc0_role_switch>;
+		};
+	};
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host2_xhci {
+	status = "okay";
+};
+
+&usbdp_phy0 {
+	mode-switch;
+	orientation-switch;
+	sbu1-dc-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+	sbu2-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbdp_phy0_orientation_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_orientation_switch>;
+		};
+
+		usbdp_phy0_dp_altmode_mux: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&usbc0_dp_altmode_mux>;
+		};
+	};
+};
-- 
2.46.0

Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add Hardkernel ODROID-M2

[Krzysztof Kozlowski]

On 01/09/2024 13:20, Jonas Karlman wrote:
> The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
> RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
> GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
> 
> Add devicetree binding documentation for the Hardkernel ODROID-M2 board.
> 
> Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
> ---

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 0/2] arm64: dts: rockchip: Add Hardkernel ODROID-M2

[Rob Herring (Arm)]

On Sun, 01 Sep 2024 11:20:13 +0000, Jonas Karlman wrote:
> This series add initial support for the Hardkernel ODROID-M2 board.
> 
> The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
> RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
> GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
> 
> Schematics for ODROID-M2 can be found at:
> https://wiki.odroid.com/_media/odroid-m2/hardware/m2_main_rev1.0_240611.pdf
> 
> The device tree was created based on the schematics with regulator
> voltage values adjusted to closer match vendor downstream device tree.
> 
> Testing was done booting into Linux using mainline U-Boot from [1],
> a test build of mainline U-Boot for ODROID-M2 can be found at [2].
> 
> U-Boot patches will be sent once DT reach the devicetree-rebasing tree.
> 
> [1] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3xxx-2024.10/
> [2] https://github.com/Kwiboo/u-boot-build/actions/runs/10653436524
> 
> Jonas Karlman (2):
>   dt-bindings: arm: rockchip: Add Hardkernel ODROID-M2
>   arm64: dts: rockchip: Add Hardkernel ODROID-M2
> 
>  .../devicetree/bindings/arm/rockchip.yaml     |   5 +
>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../boot/dts/rockchip/rk3588s-odroid-m2.dts   | 903 ++++++++++++++++++
>  3 files changed, 909 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dts
> 
> --
> 2.46.0
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y rockchip/rk3588s-odroid-m2.dtb' for 20240901112020.3224704-1-jonas@kwiboo.se:

arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dtb: video-codec@fdb50000: compatible: 'oneOf' conditional failed, one must be fixed:
	['rockchip,rk3588-vpu121', 'rockchip,rk3568-vpu'] is too long
	'rockchip,rk3588-vpu121' is not one of ['rockchip,rk3036-vpu', 'rockchip,rk3066-vpu', 'rockchip,rk3288-vpu', 'rockchip,rk3328-vpu', 'rockchip,rk3399-vpu', 'rockchip,px30-vpu', 'rockchip,rk3568-vpu', 'rockchip,rk3588-av1-vpu']
	'rockchip,rk3188-vpu' was expected
	'rockchip,rk3228-vpu' was expected
	'rockchip,rk3066-vpu' was expected
	'rockchip,rk3399-vpu' was expected
	from schema $id: http://devicetree.org/schemas/media/rockchip-vpu.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dtb: /video-codec@fdb50000: failed to match any schema with compatible: ['rockchip,rk3588-vpu121', 'rockchip,rk3568-vpu']
arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dtb: /video-codec@fdba0000: failed to match any schema with compatible: ['rockchip,rk3588-vepu121']
arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dtb: /video-codec@fdba4000: failed to match any schema with compatible: ['rockchip,rk3588-vepu121']
arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dtb: /video-codec@fdba8000: failed to match any schema with compatible: ['rockchip,rk3588-vepu121']
arch/arm64/boot/dts/rockchip/rk3588s-odroid-m2.dtb: /video-codec@fdbac000: failed to match any schema with compatible: ['rockchip,rk3588-vepu121']

Re: [PATCH 0/2] arm64: dts: rockchip: Add Hardkernel ODROID-M2

[Heiko Stuebner]

On Sun, 1 Sep 2024 11:20:13 +0000, Jonas Karlman wrote:
> This series add initial support for the Hardkernel ODROID-M2 board.
> 
> The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
> RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
> GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
> 
> Schematics for ODROID-M2 can be found at:
> https://wiki.odroid.com/_media/odroid-m2/hardware/m2_main_rev1.0_240611.pdf
> 
> [...]

Applied, thanks!

[1/2] dt-bindings: arm: rockchip: Add Hardkernel ODROID-M2
      commit: f1f348158813f64cd772d6ff4a3df0704285c14c
[2/2] arm64: dts: rockchip: Add Hardkernel ODROID-M2
      commit: ce48b8c976ce439c336def6e06bf8224a8ff9125

Best regards,
-- 
Heiko Stuebner <heiko@sntech.de>