devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Johannes Zink <j.zink@pengutronix.de>
To: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>,
	vkoul@kernel.org, kishon@kernel.org, shawnguo@kernel.org,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, linux-imx@nxp.com, robh+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, jun.li@nxp.com,
	haibo.chen@nxp.com, linux-phy@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH 1/2] dt-bindings: phy: imx8mq-usb: add phy tuning properties
Date: Wed, 05 Apr 2023 14:14:30 +0200	[thread overview]
Message-ID: <3f7257ee36dc44f162a87281c8279fd5bad91dea.camel@pengutronix.de> (raw)
In-Reply-To: <5398cbe0-c681-5dd7-0b3e-3a586cc4915f@linaro.org>

Hi Krysztof,

thanks for your review, please find my questions below.

On Wed, 2023-04-05 at 13:51 +0200, Krzysztof Kozlowski wrote:
> [snip]
> >        A phandle to the regulator for USB VBUS.
> >  
> > +  fsl,phy-tx-vref-tune:
> > +    description:
> > +      HS DC Voltage level adjustment
> 
> "Level" in what units?
> 

The datasheet just shows percent, ranging from -6 to +24%, in 2%
increments. What unit would you suggest?

> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,
> > 16]
> > +
> > +  fsl,phy-tx-rise-tune:
> > +    description:
> > +      HS Transmitter Rise/Fall Time Adjustment
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    enum: [0, 1, 2, 3]
> > +
> > +  fsl,phy-tx-preemp-amp-tune:
> > +    description:
> > +      HS Transmitter Pre-Emphasis Current Control
> 
> If this is current then use standard unit suffixes.

According to the datasheet this is in "unit amonts" of 600uA, basically
0x600uA, 1x600uA etc. Should I just suffix it with uA then?

> 
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    enum: [0, 1, 2, 3]
> > +
> > +  fsl,phy-tx-vboost-level:
> > +    description:
> > +      TX Voltage Boost Level
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    enum: [0, 2, 3]
> > +
> > +  fsl,phy-comp-dis-tune:
> > +    description:
> > +      Disconnect Threshold Adjustment
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    enum: [0, 1, 2, 3, 4, 5, 6, 7]
> > +
> > +  fsl,phy-pcs-tx-deemph-3p5db:
> > +    description:
> > +      TX De-Emphasis at 3.5 dB
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +
> > +  fsl,phy-pcs-tx-swing-full:
> > +    description:
> > +      TX Amplitude
> 
> I have feeling you just pasted here short titles from datasheet. They
> are not that helpful.

ack, I will add some more text from the register description, since I
have no other source of information on these.

Best regards
Johannes

> 
> 
> 
> Best regards,
> Krzysztof
> 
> 
> 

-- 
Pengutronix e.K.                | Johannes Zink                  |
Steuerwalder Str. 21            | https://www.pengutronix.de/    |
31137 Hildesheim, Germany       | Phone: +49-5121-206917-0       |
Amtsgericht Hildesheim, HRA 2686| Fax:   +49-5121-206917-5555    |


  reply	other threads:[~2023-04-05 12:15 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-04-05 11:21 [PATCH 0/2] Add phy tuning support for imx8mq-usb Johannes Zink
2023-04-05 11:21 ` [PATCH 1/2] dt-bindings: phy: imx8mq-usb: add phy tuning properties Johannes Zink
2023-04-05 11:51   ` Krzysztof Kozlowski
2023-04-05 12:14     ` Johannes Zink [this message]
2023-04-07  9:03       ` Krzysztof Kozlowski
2023-04-11 14:22         ` Johannes Zink
2023-04-11 14:59           ` Jun Li
2023-04-11 15:22             ` Johannes Zink
2023-04-26 10:23               ` Jun Li
2023-04-12 13:39           ` Rob Herring
2023-04-12 14:32             ` Johannes Zink
2023-04-18  9:42               ` Johannes Zink
2023-05-04  7:32                 ` Johannes Zink
2023-05-04  8:13                   ` Krzysztof Kozlowski
2023-04-05 11:21 ` [PATCH 2/2] phy: fsl-imx8mp-usb: add support for phy tuning Johannes Zink

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3f7257ee36dc44f162a87281c8279fd5bad91dea.camel@pengutronix.de \
    --to=j.zink@pengutronix.de \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=haibo.chen@nxp.com \
    --cc=jun.li@nxp.com \
    --cc=kernel@pengutronix.de \
    --cc=kishon@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=krzysztof.kozlowski@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).