Re: [PATCH] arm64: dts: qcom: sc8280xp-x13s: enable eDP display

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 11.01.2023 14:31, Johan Hovold wrote:
> Enable the eDP display on MDSS0 DP3, including backlight control.
> 
> Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
> 
> This one depends on the sc8280xp display patches:
> 
> 	https://lore.kernel.org/lkml/20230111035906.2975494-1-quic_bjorande@quicinc.com/T/#mbcdfc826df6683a71d80bab5d86645ba81b02d52
> 
> Johan
> 
> 
>  .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 75 ++++++++++++++++++-
>  1 file changed, 73 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> index 23c1ca44ec11..ef17ef90d1f0 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> @@ -47,7 +47,7 @@ wcd938x: audio-codec {
>  		#sound-dai-cells = <1>;
>  	};
>  
> -	backlight {
> +	backlight: backlight {
>  		compatible = "pwm-backlight";
>  		pwms = <&pmc8280c_lpg 3 1000000>;
>  		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
> @@ -72,6 +72,22 @@ switch-lid {
>  		};
>  	};
>  
> +	vreg_edp_3p3: regulator-edp-3p3 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VCC3LCD";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&edp_reg_en>;
> +
> +		regulator-boot-on;
> +	};
> +
>  	vreg_edp_bl: regulator-edp-bl {
>  		compatible = "regulator-fixed";
>  
> @@ -259,7 +275,6 @@ vreg_l6b: ldo6 {
>  			regulator-max-microvolt = <880000>;
>  			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  			regulator-boot-on;
> -			regulator-always-on;	/* FIXME: VDD_A_EDP_0_0P9 */
>  		};
>  	};
>  
> @@ -340,6 +355,55 @@ vreg_l9d: ldo9 {
>  	};
>  };
>  
> +&dispcc0 {
> +	status = "okay";
> +};
> +
> +&mdss0 {
> +	status = "okay";
> +};
> +
> +&mdss0_dp3 {
> +	compatible = "qcom,sc8280xp-edp";
> +
> +	data-lanes = <0 1 2 3>;
> +
> +	status = "okay";
> +
> +	aux-bus {
> +		panel {
> +			compatible = "edp-panel";
> +
> +			backlight = <&backlight>;
> +			power-supply = <&vreg_edp_3p3>;
> +
> +			ports {
> +				port {
> +					edp_panel_in: endpoint {
> +						remote-endpoint = <&mdss0_dp3_out>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	ports {
> +		port@1 {
> +			reg = <1>;
> +			mdss0_dp3_out: endpoint {
> +				remote-endpoint = <&edp_panel_in>;
> +			};
> +		};
> +	};
> +};
> +
> +&mdss0_dp3_phy {
> +	vdda-phy-supply = <&vreg_l6b>;
> +	vdda-pll-supply = <&vreg_l3b>;
> +
> +	status = "okay";
> +};
> +
>  &pcie2a {
>  	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
>  	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> @@ -902,6 +966,13 @@ hastings_reg_en: hastings-reg-en-state {
>  &tlmm {
>  	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>  
> +	edp_reg_en: edp-reg-en-state {
> +		pins = "gpio25";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-disable;
> +	};
> +
>  	hall_int_n_default: hall-int-n-state {
>  		pins = "gpio107";
>  		function = "gpio";