Re: [PATCH v1 9/9] arm64: dts: qcom: sm8350-hdk: Enable lt9611uxc dsi-hdmi bridge

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 28/10/2022 08:08, Robert Foss wrote:
> The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.
> 
> In order to toggle the board to enable the HDMI output,
> switch #7 & #8 on the rightmost multi-switch package have
> to be toggled to On.
> 
> Signed-off-by: Robert Foss <robert.foss@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 106 ++++++++++++++++++++++++
>  1 file changed, 106 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 6e07feb4b3b2..6666b38b58f8 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -20,6 +20,17 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	hdmi-out {

Generic node names, so hdmi-connector or just connector.

> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&lt9611_out>;
> +			};
> +		};
> +	};
> +
>  	vph_pwr: vph-pwr-regulator {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vph_pwr";
> @@ -29,6 +40,32 @@ vph_pwr: vph-pwr-regulator {
>  		regulator-always-on;
>  		regulator-boot-on;
>  	};
> +
> +	lt9611_1v2: lt9611-1v2 {

Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {

Ditto


> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };
>  
>  &adsp {
> @@ -220,6 +257,15 @@ &dispcc {
>  &dsi0 {
>  	status = "okay";
>  	vdda-supply = <&vreg_l6b_1p2>;
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&lt9611_a>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
>  };
>  
>  &dsi0_phy  {
> @@ -231,6 +277,48 @@ &gpi_dma1 {
>  	status = "okay";
>  };
>  
> +&i2c15 {
> +	status = "okay";

status is the last property

> +	clock-frequency = <400000>;
> +
> +	lt9611_codec: hdmi-bridge@2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +		status = "okay";

Why status?

> +
> +		interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
> +		reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				lt9611_a: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +
> +				lt9611_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +

No need for blank line

> +		};
> +	};
> +};
> +
>  &mdss {
>  	status = "okay";
>  };
> @@ -248,6 +336,10 @@ &qupv3_id_0 {
>  	status = "okay";
>  };
>  
> +&qupv3_id_2 {
> +	status = "okay";
> +};
> +
>  &slpi {
>  	status = "okay";
>  	firmware-name = "qcom/sm8350/slpi.mbn";
> @@ -544,4 +636,18 @@ usb_hub_enabled_state: usb-hub-enabled-state {
>  		drive-strength = <2>;
>  		output-low;
>  	};
> +
> +	lt9611_rst_pin: lt9611-rst-state {
> +		pins = "gpio48";
> +		function = "normal";
> +
> +		output-high;
> +		input-disable;
> +	};
> +
> +	lt9611_irq_pin: lt9611-irq {

Missing suffix 'state'.

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

Rebase your changes on last linux-next.

Best regards,
Krzysztof