devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Nicolas Ferre <nicolas.ferre@microchip.com>
To: Tudor Ambarus <tudor.ambarus@linaro.org>, <claudiu.beznea@microchip.com>
Cc: <alexandre.belloni@bootlin.com>, <robh+dt@kernel.org>,
	<krzysztof.kozlowski+dt@linaro.org>, <devicetree@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>,
	"Tudor Ambarus" <tudor.ambarus@microchip.com>
Subject: Re: [PATCH v3 3/4] ARM: dts: at91: sama5d2_icp: Set sst26vf064b SPI NOR flash at its maximum frequency
Date: Thu, 30 Mar 2023 20:41:30 +0200	[thread overview]
Message-ID: <4328668b-26c7-ebe7-f839-b6accd0a38f9@microchip.com> (raw)
In-Reply-To: <20230328101517.1595738-4-tudor.ambarus@linaro.org>

On 28/03/2023 at 12:15, Tudor Ambarus wrote:
> From: Tudor Ambarus <tudor.ambarus@microchip.com>
> 
> sama5d2_icp populates an sst26vf064b SPI NOR flash. Its maximum operating
> frequency for 2.7-3.6V is 104 MHz. As the flash is operated at 3.3V,
> increase its maximum supported frequency to 104MHz. The increasing of the
> spi-max-frequency value requires the setting of the
> "CE# Not Active Hold Time", thus set the spi-cs-setup-ns to a value of 7.
> 
> The sst26vf064b datasheet specifies just a minimum value for the
> "CE# Not Active Hold Time" and it advertises it to 5 ns. There's no
> maximum time specified. I determined experimentally that 5 ns for the
> spi-cs-setup-ns is not enough when the flash is operated close to its
> maximum frequency and tests showed that 7 ns is just fine, so set the
> spi-cs-setup-ns dt property to 7.
> 
> With the increase of frequency the reads are now faster with ~37%.
> 
> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com> # on sama5d2 ICP 
board with a linux-next kernel today.

Thanks Tudor!

Best regards,
   Nicolas

> ---
>   arch/arm/boot/dts/at91-sama5d2_icp.dts | 3 ++-
>   1 file changed, 2 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts
> index 1346b8f2b259..999adeca6f33 100644
> --- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
> +++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts
> @@ -669,7 +669,8 @@ flash@0 {
>                  #size-cells = <1>;
>                  compatible = "jedec,spi-nor";
>                  reg = <0>;
> -               spi-max-frequency = <80000000>;
> +               spi-max-frequency = <104000000>;
> +               spi-cs-setup-ns = <7>;
>                  spi-tx-bus-width = <4>;
>                  spi-rx-bus-width = <4>;
>                  m25p,fast-read;
> --
> 2.40.0.348.gf938b09366-goog
> 

-- 
Nicolas Ferre


  reply	other threads:[~2023-03-30 18:42 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-03-28 10:15 [PATCH v3 0/4] ARM: dts: at91: Set sst26vf064b SPI NOR flash at its maxumum frequency Tudor Ambarus
2023-03-28 10:15 ` [PATCH v3 1/4] ARM: dts: at91-sama5d27_wlsom1: Set sst26vf064b SPI NOR flash at its maximum frequency Tudor Ambarus
2023-03-28 10:23   ` Tudor Ambarus
2023-03-28 10:15 ` [PATCH v3 2/4] ARM: dts: at91-sama5d27_som1: " Tudor Ambarus
2023-03-28 10:15 ` [PATCH v3 3/4] ARM: dts: at91: sama5d2_icp: " Tudor Ambarus
2023-03-30 18:41   ` Nicolas Ferre [this message]
2023-03-28 10:15 ` [PATCH v3 4/4] ARM: dts: at91: sam9x60ek: " Tudor Ambarus
2023-03-30 18:53 ` [PATCH v3 0/4] ARM: dts: at91: Set sst26vf064b SPI NOR flash at its maxumum frequency Nicolas Ferre
2023-03-31  9:57   ` Tudor Ambarus

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4328668b-26c7-ebe7-f839-b6accd0a38f9@microchip.com \
    --to=nicolas.ferre@microchip.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=claudiu.beznea@microchip.com \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=tudor.ambarus@linaro.org \
    --cc=tudor.ambarus@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).