Re: [V3, 3/4] Documentation: dt-bindings: media: Document bindings for DW MIPI CSI-2 Host

[Luis de Oliveira <luis.oliveira@synopsys.com>]

On 24-Oct-18 18:40, Rob Herring wrote:
> On Fri, Oct 19, 2018 at 02:52:25PM +0200, Luis Oliveira wrote:
>> Add bindings for Synopsys DesignWare MIPI CSI-2 host.
>>
>> Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
>> ---
>> Changelog
>> v2-V3
>> - removed IPI settings
>>
>>  .../devicetree/bindings/media/snps,dw-csi-plat.txt | 52 ++++++++++++++++++++++
>>  1 file changed, 52 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>>
>> diff --git a/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt b/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>> new file mode 100644
>> index 0000000..be3da05
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
>> @@ -0,0 +1,52 @@
>> +Synopsys DesignWare CSI-2 Host controller
>> +
>> +Description
>> +-----------
>> +
>> +This HW block is used to receive image coming from an MIPI CSI-2 compatible
>> +camera.
>> +
>> +Required properties:
>> +- compatible: shall be "snps,dw-csi-plat"
> 
> 'plat' is really part of the name of the h/w block?
> 

It is the name of the platform driver for CSI compatible with this block. Is
that wrong?

>> +- reg			: physical base address and size of the device memory mapped
>> +  registers;
>> +- interrupts		: CSI-2 Host interrupt
>> +- snps,output-type	: Core output to be used (IPI-> 0 or IDI->1 or BOTH->2)
>> +			  These  values choose which of the Core outputs will be used,
>> +			  it can be Image Data Interface or Image Pixel Interface.
>> +- phys			: List of one PHY specifier (as defined in
>> +			  Documentation/devicetree/bindings/phy/phy-bindings.txt).
>> +			  This PHY is a MIPI DPHY working in RX mode.
>> +- resets		: Reference to a reset controller (optional)
>> +
>> +The per-board settings:
>> + - port sub-node describing a single endpoint connected to the camera as
>> +   described in video-interfaces.txt[1].
> 
> Need to say 2 ports and what is each port? Why no port #0?
> 

I will elaborate on that.

>> +
>> +Example:
>> +
>> +	csi2_1: csi2@3000 {
>> +		compatible = "snps,dw-csi-plat";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		reg = < 0x03000 0x7FF>;
>> +		interrupts = <2>;
>> +		output-type = <2>;
>> +		resets = <&dw_rst 1>;
>> +		phys = <&mipi_dphy_rx1 0>;
>> +		phy-names = "csi2-dphy";
> 
> Not documented. Not really needed for a single entry, so I'd just drop 
> it.
> 

I will, thanks.

>> +
>> +		/* CSI-2 per-board settings */
>> +		port@1 {
>> +			reg = <1>;
>> +			csi1_ep1: endpoint {
>> +				remote-endpoint = <&camera_1>;
>> +				data-lanes = <1 2>;
>> +			};
>> +		};
>> +		port@2 {
>> +			csi1_ep2: endpoint {
>> +				remote-endpoint = <&vif1_ep>;
>> +			};
>> +		};
>> +	};
>> --
>> 2.7.4
>>