[PATCH v5] MTD: LPC32xx SLC NAND driver

[PATCH v5] MTD: LPC32xx SLC NAND driver

[Roland Stigge]

This patch adds support for the SLC NAND controller inside the LPC32xx SoC.

Signed-off-by: Roland Stigge <stigge@antcom.de>

---
Applies to 3.5-rc1

Changes since v4:
* Dropped superfluous error handling of dmaengine_submit()
* Added unmapping of dma sg buffers

Changes since v3:
* Adjusted to mtd API changes

Changes since v2:
* Fixed dma data direction and dma transfer direction differences
* Removed dma_sync_sg_for_cpu() - not necessary due to unmap
* Removed dma_set_mask()

Changes since v1:
* Fixed busy wait DMA timeout with cpu_relax() - unexpected condition anyway
* Fixed comment of dma_setup function
* Minor cleanup

Thanks to Artem Bityutskiy, Huang Shijie and Russell King for reviewing!

 Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt |   52 
 drivers/mtd/nand/Kconfig                              |   11 
 drivers/mtd/nand/Makefile                             |    1 
 drivers/mtd/nand/lpc32xx_nand_slc.c                   | 1060 ++++++++++++++++++
 4 files changed, 1124 insertions(+)

--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt
@@ -0,0 +1,52 @@
+NXP LPC32xx SoC NAND SLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-slc"
+- reg: Address and size of the controller
+- nand-on-flash-bbt: Use bad block table on flash
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual:
+- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY)
+- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY)
+(The following values are specified in Hz, to make them independent of actual
+clock speed:)
+- nxp,wwidth: Write pulse width (W_WIDTH)
+- nxp,whold: Write hold time (W_HOLD)
+- nxp,wsetup: Write setup time (W_SETUP)
+- nxp,rwidth: Read pulse width (R_WIDTH)
+- nxp,rhold: Read hold time (R_HOLD)
+- nxp,rsetup: Read setup time (R_SETUP)
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	slc: flash@20020000 {
+		compatible = "nxp,lpc3220-slc";
+		reg = <0x20020000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,wdr-clks = <14>;
+		nxp,wwidth = <40000000>;
+		nxp,whold = <100000000>;
+		nxp,wsetup = <100000000>;
+		nxp,rdr-clks = <14>;
+		nxp,rwidth = <40000000>;
+		nxp,rhold = <66666666>;
+		nxp,rsetup = <100000000>;
+		nand-on-flash-bbt;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "phy3250-boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};
--- linux-2.6.orig/drivers/mtd/nand/Kconfig
+++ linux-2.6/drivers/mtd/nand/Kconfig
@@ -454,6 +454,17 @@ config MTD_NAND_PXA3xx
 	  This enables the driver for the NAND flash device found on
 	  PXA3xx processors
 
+config MTD_NAND_SLC_LPC32XX
+	bool "NXP LPC32xx SLC Controller"
+	depends on ARCH_LPC32XX
+	help
+	  Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
+	  chips) NAND controller. This is the default for the PHYTEC 3250
+	  reference board which contains a NAND256R3A2CZA6 chip.
+
+	  Please check the actual NAND chip connected and its support
+	  by the SLC NAND controller.
+
 config MTD_NAND_CM_X270
 	tristate "Support for NAND Flash on CM-X270 modules"
 	depends on MACH_ARMCORE
--- linux-2.6.orig/drivers/mtd/nand/Makefile
+++ linux-2.6/drivers/mtd/nand/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_MTD_NAND_ORION)		+= orion_n
 obj-$(CONFIG_MTD_NAND_FSL_ELBC)		+= fsl_elbc_nand.o
 obj-$(CONFIG_MTD_NAND_FSL_IFC)		+= fsl_ifc_nand.o
 obj-$(CONFIG_MTD_NAND_FSL_UPM)		+= fsl_upm.o
+obj-$(CONFIG_MTD_NAND_SLC_LPC32XX)      += lpc32xx_nand_slc.o
 obj-$(CONFIG_MTD_NAND_SH_FLCTL)		+= sh_flctl.o
 obj-$(CONFIG_MTD_NAND_MXC)		+= mxc_nand.o
 obj-$(CONFIG_MTD_NAND_SOCRATES)		+= socrates_nand.o
--- /dev/null
+++ linux-2.6/drivers/mtd/nand/lpc32xx_nand_slc.c
@@ -0,0 +1,1060 @@
+/*
+ * NXP LPC32XX NAND SLC driver
+ *
+ * Authors:
+ *    Kevin Wells <kevin.wells@nxp.com>
+ *    Roland Stigge <stigge@antcom.de>
+ *
+ * Copyright (C) 2011 NXP Semiconductors
+ * Copyright (C) 2012 Roland Stigge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/mm.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_mtd.h>
+#include <linux/of_gpio.h>
+#include <linux/amba/pl08x.h>
+
+#define LPC32XX_MODNAME		"lpc32xx-nand"
+
+/**********************************************************************
+* SLC NAND controller register offsets
+**********************************************************************/
+
+#define SLC_DATA(x)		(x + 0x000)
+#define SLC_ADDR(x)		(x + 0x004)
+#define SLC_CMD(x)		(x + 0x008)
+#define SLC_STOP(x)		(x + 0x00C)
+#define SLC_CTRL(x)		(x + 0x010)
+#define SLC_CFG(x)		(x + 0x014)
+#define SLC_STAT(x)		(x + 0x018)
+#define SLC_INT_STAT(x)		(x + 0x01C)
+#define SLC_IEN(x)		(x + 0x020)
+#define SLC_ISR(x)		(x + 0x024)
+#define SLC_ICR(x)		(x + 0x028)
+#define SLC_TAC(x)		(x + 0x02C)
+#define SLC_TC(x)		(x + 0x030)
+#define SLC_ECC(x)		(x + 0x034)
+#define SLC_DMA_DATA(x)		(x + 0x038)
+
+/**********************************************************************
+* slc_ctrl register definitions
+**********************************************************************/
+#define SLCCTRL_SW_RESET	(1 << 2) /* Reset the NAND controller bit */
+#define SLCCTRL_ECC_CLEAR	(1 << 1) /* Reset ECC bit */
+#define SLCCTRL_DMA_START	(1 << 0) /* Start DMA channel bit */
+
+/**********************************************************************
+* slc_cfg register definitions
+**********************************************************************/
+#define SLCCFG_CE_LOW		(1 << 5) /* Force CE low bit */
+#define SLCCFG_DMA_ECC		(1 << 4) /* Enable DMA ECC bit */
+#define SLCCFG_ECC_EN		(1 << 3) /* ECC enable bit */
+#define SLCCFG_DMA_BURST	(1 << 2) /* DMA burst bit */
+#define SLCCFG_DMA_DIR		(1 << 1) /* DMA write(0)/read(1) bit */
+#define SLCCFG_WIDTH		(1 << 0) /* External device width, 0=8bit */
+
+/**********************************************************************
+* slc_stat register definitions
+**********************************************************************/
+#define SLCSTAT_DMA_FIFO	(1 << 2) /* DMA FIFO has data bit */
+#define SLCSTAT_SLC_FIFO	(1 << 1) /* SLC FIFO has data bit */
+#define SLCSTAT_NAND_READY	(1 << 0) /* NAND device is ready bit */
+
+/**********************************************************************
+* slc_int_stat, slc_ien, slc_isr, and slc_icr register definitions
+**********************************************************************/
+#define SLCSTAT_INT_TC		(1 << 1) /* Transfer count bit */
+#define SLCSTAT_INT_RDY_EN	(1 << 0) /* Ready interrupt bit */
+
+/**********************************************************************
+* slc_tac register definitions
+**********************************************************************/
+/* Clock setting for RDY write sample wait time in 2*n clocks */
+#define SLCTAC_WDR(n)		(((n) & 0xF) << 28)
+/* Write pulse width in clock cycles, 1 to 16 clocks */
+#define SLCTAC_WWIDTH(n)	(((n) & 0xF) << 24)
+/* Write hold time of control and data signals, 1 to 16 clocks */
+#define SLCTAC_WHOLD(n)		(((n) & 0xF) << 20)
+/* Write setup time of control and data signals, 1 to 16 clocks */
+#define SLCTAC_WSETUP(n)	(((n) & 0xF) << 16)
+/* Clock setting for RDY read sample wait time in 2*n clocks */
+#define SLCTAC_RDR(n)		(((n) & 0xF) << 12)
+/* Read pulse width in clock cycles, 1 to 16 clocks */
+#define SLCTAC_RWIDTH(n)	(((n) & 0xF) << 8)
+/* Read hold time of control and data signals, 1 to 16 clocks */
+#define SLCTAC_RHOLD(n)		(((n) & 0xF) << 4)
+/* Read setup time of control and data signals, 1 to 16 clocks */
+#define SLCTAC_RSETUP(n)	(((n) & 0xF) << 0)
+
+/**********************************************************************
+* slc_ecc register definitions
+**********************************************************************/
+/* ECC line party fetch macro */
+#define SLCECC_TO_LINEPAR(n)	(((n) >> 6) & 0x7FFF)
+#define SLCECC_TO_COLPAR(n)	((n) & 0x3F)
+
+/*
+ * DMA requires storage space for the DMA local buffer and the hardware ECC
+ * storage area. The DMA local buffer is only used if DMA mapping fails
+ * during runtime.
+ */
+#define LPC32XX_DMA_DATA_SIZE		4096
+#define LPC32XX_ECC_SAVE_SIZE		((4096 / 256) * 4)
+
+/* Number of bytes used for ECC stored in NAND per 256 bytes */
+#define LPC32XX_SLC_DEV_ECC_BYTES	3
+
+/*
+ * If the NAND base clock frequency can't be fetched, this frequency will be
+ * used instead as the base. This rate is used to setup the timing registers
+ * used for NAND accesses.
+ */
+#define LPC32XX_DEF_BUS_RATE		133250000
+
+/* Milliseconds for DMA FIFO timeout (unlikely anyway) */
+#define LPC32XX_DMA_TIMEOUT		100
+
+/*
+ * NAND ECC Layout for small page NAND devices
+ * Note: For large and huge page devices, the default layouts are used
+ */
+static struct nand_ecclayout lpc32xx_nand_oob_16 = {
+	.eccbytes = 6,
+	.eccpos = {10, 11, 12, 13, 14, 15},
+	.oobfree = {
+		{ .offset = 0, .length = 4 },
+		{ .offset = 6, .length = 4 },
+	},
+};
+
+static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
+static u8 mirror_pattern[] = {'1', 't', 'b', 'B' };
+
+/*
+ * Small page FLASH BBT descriptors, marker at offset 0, version at offset 6
+ * Note: Large page devices used the default layout
+ */
+static struct nand_bbt_descr bbt_smallpage_main_descr = {
+	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+		| NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+	.offs =	0,
+	.len = 4,
+	.veroffs = 6,
+	.maxblocks = 4,
+	.pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_smallpage_mirror_descr = {
+	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+		| NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+	.offs =	0,
+	.len = 4,
+	.veroffs = 6,
+	.maxblocks = 4,
+	.pattern = mirror_pattern
+};
+
+/*
+ * NAND platform configuration structure
+ */
+struct lpc32xx_nand_cfg_slc {
+	u32     wdr_clks;
+	u32     wwidth;
+	u32     whold;
+	u32     wsetup;
+	u32     rdr_clks;
+	u32     rwidth;
+	u32     rhold;
+	u32     rsetup;
+	bool    use_bbt;
+	unsigned wp_gpio;
+	struct mtd_partition *parts;
+	unsigned num_parts;
+};
+
+struct lpc32xx_nand_host {
+	struct nand_chip	nand_chip;
+	struct clk		*clk;
+	struct mtd_info		mtd;
+	void __iomem		*io_base;
+	struct lpc32xx_nand_cfg_slc *ncfg;
+
+	struct completion	comp;
+	struct dma_chan		*dma_chan;
+	u32			dma_buf_len;
+	struct dma_slave_config	dma_slave_config;
+	struct scatterlist	sgl;
+
+	/*
+	 * DMA and CPU addresses of ECC work area and data buffer
+	 */
+	u32			*ecc_buf;
+	u8			*data_buf;
+	dma_addr_t		io_base_dma;
+};
+
+static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host)
+{
+	u32 clkrate, tmp;
+
+	/* Reset SLC controller */
+	writel(SLCCTRL_SW_RESET, SLC_CTRL(host->io_base));
+	udelay(1000);
+
+	/* Basic setup */
+	writel(0, SLC_CFG(host->io_base));
+	writel(0, SLC_IEN(host->io_base));
+	writel((SLCSTAT_INT_TC | SLCSTAT_INT_RDY_EN),
+		SLC_ICR(host->io_base));
+
+	/* Get base clock for SLC block */
+	clkrate = clk_get_rate(host->clk);
+	if (clkrate == 0)
+		clkrate = LPC32XX_DEF_BUS_RATE;
+
+	/* Compute clock setup values */
+	tmp = SLCTAC_WDR(host->ncfg->wdr_clks) |
+		SLCTAC_WWIDTH(1 + (clkrate / host->ncfg->wwidth)) |
+		SLCTAC_WHOLD(1 + (clkrate / host->ncfg->whold)) |
+		SLCTAC_WSETUP(1 + (clkrate / host->ncfg->wsetup)) |
+		SLCTAC_RDR(host->ncfg->rdr_clks) |
+		SLCTAC_RWIDTH(1 + (clkrate / host->ncfg->rwidth)) |
+		SLCTAC_RHOLD(1 + (clkrate / host->ncfg->rhold)) |
+		SLCTAC_RSETUP(1 + (clkrate / host->ncfg->rsetup));
+	writel(tmp, SLC_TAC(host->io_base));
+}
+
+/*
+ * Hardware specific access to control lines
+ */
+static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+	unsigned int ctrl)
+{
+	u32 tmp;
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+
+	/* Does CE state need to be changed? */
+	tmp = readl(SLC_CFG(host->io_base));
+	if (ctrl & NAND_NCE)
+		tmp |= SLCCFG_CE_LOW;
+	else
+		tmp &= ~SLCCFG_CE_LOW;
+	writel(tmp, SLC_CFG(host->io_base));
+
+	if (cmd != NAND_CMD_NONE) {
+		if (ctrl & NAND_CLE)
+			writel(cmd, SLC_CMD(host->io_base));
+		else
+			writel(cmd, SLC_ADDR(host->io_base));
+	}
+}
+
+/*
+ * Read the Device Ready pin
+ */
+static int lpc32xx_nand_device_ready(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+	int rdy = 0;
+
+	if ((readl(SLC_STAT(host->io_base)) & SLCSTAT_NAND_READY) != 0)
+		rdy = 1;
+
+	return rdy;
+}
+
+/*
+ * Enable NAND write protect
+ */
+static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host)
+{
+	gpio_set_value(host->ncfg->wp_gpio, 0);
+}
+
+/*
+ * Disable NAND write protect
+ */
+static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
+{
+	gpio_set_value(host->ncfg->wp_gpio, 1);
+}
+
+/*
+ * Prepares SLC for transfers with H/W ECC enabled
+ */
+static void lpc32xx_nand_ecc_enable(struct mtd_info *mtd, int mode)
+{
+	/* Hardware ECC is enabled automatically in hardware as needed */
+}
+
+/*
+ * Calculates the ECC for the data
+ */
+static int lpc32xx_nand_ecc_calculate(struct mtd_info *mtd,
+				      const unsigned char *buf,
+				      unsigned char *code)
+{
+	/*
+	 * ECC is calculated automatically in hardware during syndrome read
+	 * and write operations, so it doesn't need to be calculated here.
+	 */
+	return 0;
+}
+
+/*
+ * Read a single byte from NAND device
+ */
+static u8 lpc32xx_nand_read_byte(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+
+	return (u8)readl(SLC_DATA(host->io_base));
+}
+
+/*
+ * Simple device read without ECC
+ */
+static void lpc32xx_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+
+	/* Direct device read with no ECC */
+	while (len-- > 0)
+		*buf++ = (u8)readl(SLC_DATA(host->io_base));
+}
+
+/*
+ * Simple device write without ECC
+ */
+static void lpc32xx_nand_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+
+	/* Direct device write with no ECC */
+	while (len-- > 0)
+		writel((u32)*buf++, SLC_DATA(host->io_base));
+}
+
+/*
+ * Verify data in buffer to data on device
+ */
+static int lpc32xx_verify_buf(struct mtd_info *mtd, const u8 *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+	int i;
+
+	/* DATA register must be read as 32 bits or it will fail */
+	for (i = 0; i < len; i++) {
+		if (buf[i] != (u8)readl(SLC_DATA(host->io_base)))
+			return -EFAULT;
+	}
+
+	return 0;
+}
+
+/*
+ * Read the OOB data from the device without ECC using FIFO method
+ */
+static int lpc32xx_nand_read_oob_syndrome(struct mtd_info *mtd,
+					  struct nand_chip *chip, int page)
+{
+	chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	return 0;
+}
+
+/*
+ * Write the OOB data to the device without ECC using FIFO method
+ */
+static int lpc32xx_nand_write_oob_syndrome(struct mtd_info *mtd,
+	struct nand_chip *chip, int page)
+{
+	int status;
+
+	chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page);
+	chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	/* Send command to program the OOB data */
+	chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+
+	status = chip->waitfunc(mtd, chip);
+
+	return status & NAND_STATUS_FAIL ? -EIO : 0;
+}
+
+/*
+ * Fills in the ECC fields in the OOB buffer with the hardware generated ECC
+ */
+static void lpc32xx_slc_ecc_copy(u8 *spare, const u32 *ecc, int count)
+{
+	int i;
+
+	for (i = 0; i < (count * 3); i += 3) {
+		u32 ce = ecc[i / 3];
+		ce = ~(ce << 2) & 0xFFFFFF;
+		spare[i + 2] = (u8)(ce & 0xFF);
+		ce >>= 8;
+		spare[i + 1] = (u8)(ce & 0xFF);
+		ce >>= 8;
+		spare[i] = (u8)(ce & 0xFF);
+	}
+}
+
+static void lpc32xx_dma_complete_func(void *completion)
+{
+	complete(completion);
+}
+
+static int lpc32xx_xmit_dma(struct mtd_info *mtd, dma_addr_t dma,
+			    void *mem, int len, enum dma_transfer_direction dir)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+	struct dma_async_tx_descriptor *desc;
+	int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+	int res;
+
+	host->dma_slave_config.direction = dir;
+	host->dma_slave_config.src_addr = dma;
+	host->dma_slave_config.dst_addr = dma;
+	host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	host->dma_slave_config.src_maxburst = 4;
+	host->dma_slave_config.dst_maxburst = 4;
+	/* DMA controller does flow control: */
+	host->dma_slave_config.device_fc = false;
+	if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) {
+		dev_err(mtd->dev.parent, "Failed to setup DMA slave\n");
+		return -ENXIO;
+	}
+
+	sg_init_one(&host->sgl, mem, len);
+
+	res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1,
+			 DMA_BIDIRECTIONAL);
+	if (res != 1) {
+		dev_err(mtd->dev.parent, "Failed to map sg list\n");
+		return -ENXIO;
+	}
+	desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir,
+				       flags);
+	if (!desc) {
+		dev_err(mtd->dev.parent, "Failed to prepare slave sg\n");
+		goto out1;
+	}
+
+	init_completion(&host->comp);
+	desc->callback = lpc32xx_dma_complete_func;
+	desc->callback_param = &host->comp;
+
+	dmaengine_submit(desc);
+	dma_async_issue_pending(host->dma_chan);
+
+	wait_for_completion_timeout(&host->comp, msecs_to_jiffies(1000));
+
+	dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1,
+		     DMA_BIDIRECTIONAL);
+
+	return 0;
+out1:
+	dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1,
+		     DMA_BIDIRECTIONAL);
+	return -ENXIO;
+}
+
+/*
+ * DMA read/write transfers with ECC support
+ */
+static int lpc32xx_xfer(struct mtd_info *mtd, u8 *buf, int eccsubpages,
+			int read)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+	int i, status = 0;
+	unsigned long timeout;
+	int res;
+	enum dma_transfer_direction dir =
+		read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV;
+	u8 *dma_buf;
+	bool dma_mapped;
+
+	if ((void *)buf <= high_memory) {
+		dma_buf = buf;
+		dma_mapped = true;
+	} else {
+		dma_buf = host->data_buf;
+		dma_mapped = false;
+		if (!read)
+			memcpy(host->data_buf, buf, mtd->writesize);
+	}
+
+	if (read) {
+		writel(readl(SLC_CFG(host->io_base)) |
+		       SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC |
+		       SLCCFG_DMA_BURST, SLC_CFG(host->io_base));
+	} else {
+		writel((readl(SLC_CFG(host->io_base)) |
+			SLCCFG_ECC_EN | SLCCFG_DMA_ECC | SLCCFG_DMA_BURST) &
+		       ~SLCCFG_DMA_DIR,
+			SLC_CFG(host->io_base));
+	}
+
+	/* Clear initial ECC */
+	writel(SLCCTRL_ECC_CLEAR, SLC_CTRL(host->io_base));
+
+	/* Transfer size is data area only */
+	writel(mtd->writesize, SLC_TC(host->io_base));
+
+	/* Start transfer in the NAND controller */
+	writel(readl(SLC_CTRL(host->io_base)) | SLCCTRL_DMA_START,
+	       SLC_CTRL(host->io_base));
+
+	for (i = 0; i < chip->ecc.steps; i++) {
+		/* Data */
+		res = lpc32xx_xmit_dma(mtd, SLC_DMA_DATA(host->io_base_dma),
+				       dma_buf + i * chip->ecc.size,
+				       mtd->writesize / chip->ecc.steps, dir);
+		if (res)
+			return res;
+
+		/* Always _read_ ECC */
+		if (i == chip->ecc.steps - 1)
+			break;
+		if (!read) /* ECC availability delayed on write */
+			udelay(10);
+		res = lpc32xx_xmit_dma(mtd, SLC_ECC(host->io_base_dma),
+				       &host->ecc_buf[i], 4, DMA_DEV_TO_MEM);
+		if (res)
+			return res;
+	}
+
+	/*
+	 * According to NXP, the DMA can be finished here, but the NAND
+	 * controller may still have buffered data. After porting to using the
+	 * dmaengine DMA driver (amba-pl080), the condition (DMA_FIFO empty)
+	 * appears to be always true, according to tests. Keeping the check for
+	 * safety reasons for now.
+	 */
+	if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) {
+		dev_warn(mtd->dev.parent, "FIFO not empty!\n");
+		timeout = jiffies + msecs_to_jiffies(LPC32XX_DMA_TIMEOUT);
+		while ((readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) &&
+		       time_before(jiffies, timeout))
+			cpu_relax();
+		if (!time_before(jiffies, timeout)) {
+			dev_err(mtd->dev.parent, "FIFO held data too long\n");
+			status = -EIO;
+		}
+	}
+
+	/* Read last calculated ECC value */
+	if (!read)
+		udelay(10);
+	host->ecc_buf[chip->ecc.steps - 1] =
+		readl(SLC_ECC(host->io_base));
+
+	/* Flush DMA */
+	dmaengine_terminate_all(host->dma_chan);
+
+	if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO ||
+	    readl(SLC_TC(host->io_base))) {
+		/* Something is left in the FIFO, something is wrong */
+		dev_err(mtd->dev.parent, "DMA FIFO failure\n");
+		status = -EIO;
+	}
+
+	/* Stop DMA & HW ECC */
+	writel(readl(SLC_CTRL(host->io_base)) & ~SLCCTRL_DMA_START,
+	       SLC_CTRL(host->io_base));
+	writel(readl(SLC_CFG(host->io_base)) &
+	       ~(SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC |
+		 SLCCFG_DMA_BURST), SLC_CFG(host->io_base));
+
+	if (!dma_mapped && read)
+		memcpy(buf, host->data_buf, mtd->writesize);
+
+	return status;
+}
+
+/*
+ * Read the data and OOB data from the device, use ECC correction with the
+ * data, disable ECC for the OOB data
+ */
+static int lpc32xx_nand_read_page_syndrome(struct mtd_info *mtd,
+					   struct nand_chip *chip, u8 *buf,
+					   int oob_required, int page)
+{
+	struct lpc32xx_nand_host *host = chip->priv;
+	int stat, i, status;
+	u8 *oobecc, tmpecc[LPC32XX_ECC_SAVE_SIZE];
+
+	/* Issue read command */
+	chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+
+	/* Read data and oob, calculate ECC */
+	status = lpc32xx_xfer(mtd, buf, chip->ecc.steps, 1);
+
+	/* Get OOB data */
+	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	/* Convert to stored ECC format */
+	lpc32xx_slc_ecc_copy(tmpecc, (u32 *) host->ecc_buf, chip->ecc.steps);
+
+	/* Pointer to ECC data retrieved from NAND spare area */
+	oobecc = chip->oob_poi + chip->ecc.layout->eccpos[0];
+
+	for (i = 0; i < chip->ecc.steps; i++) {
+		stat = chip->ecc.correct(mtd, buf, oobecc,
+					 &tmpecc[i * chip->ecc.bytes]);
+		if (stat < 0)
+			mtd->ecc_stats.failed++;
+		else
+			mtd->ecc_stats.corrected += stat;
+
+		buf += chip->ecc.size;
+		oobecc += chip->ecc.bytes;
+	}
+
+	return status;
+}
+
+/*
+ * Read the data and OOB data from the device, no ECC correction with the
+ * data or OOB data
+ */
+static int lpc32xx_nand_read_page_raw_syndrome(struct mtd_info *mtd,
+					       struct nand_chip *chip,
+					       u8 *buf, int oob_required,
+					       int page)
+{
+	/* Issue read command */
+	chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+
+	/* Raw reads can just use the FIFO interface */
+	chip->read_buf(mtd, buf, chip->ecc.size * chip->ecc.steps);
+	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	return 0;
+}
+
+/*
+ * Write the data and OOB data to the device, use ECC with the data,
+ * disable ECC for the OOB data
+ */
+static void lpc32xx_nand_write_page_syndrome(struct mtd_info *mtd,
+					     struct nand_chip *chip,
+					     const u8 *buf, int oob_required)
+{
+	struct lpc32xx_nand_host *host = chip->priv;
+	u8 *pb = chip->oob_poi + chip->ecc.layout->eccpos[0];
+
+	/* Write data, calculate ECC on outbound data */
+	lpc32xx_xfer(mtd, (u8 *)buf, chip->ecc.steps, 0);
+
+	/*
+	 * The calculated ECC needs some manual work done to it before
+	 * committing it to NAND. Process the calculated ECC and place
+	 * the resultant values directly into the OOB buffer. */
+	lpc32xx_slc_ecc_copy(pb, (u32 *)host->ecc_buf, chip->ecc.steps);
+
+	/* Write ECC data to device */
+	chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+}
+
+/*
+ * Write the data and OOB data to the device, no ECC correction with the
+ * data or OOB data
+ */
+static void lpc32xx_nand_write_page_raw_syndrome(struct mtd_info *mtd,
+						 struct nand_chip *chip,
+						 const u8 *buf,
+						 int oob_required)
+{
+	/* Raw writes can just use the FIFO interface */
+	chip->write_buf(mtd, buf, chip->ecc.size * chip->ecc.steps);
+	chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+}
+
+static bool lpc32xx_dma_filter(struct dma_chan *chan, void *param)
+{
+	struct pl08x_dma_chan *ch =
+		container_of(chan, struct pl08x_dma_chan, chan);
+
+	/* In LPC32xx's PL080 DMA wiring, the SLC NAND DMA signal is #1 */
+	if (ch->cd->min_signal == 1)
+		return true;
+	return false;
+}
+
+static int lpc32xx_nand_dma_setup(struct lpc32xx_nand_host *host)
+{
+	struct mtd_info *mtd = &host->mtd;
+	dma_cap_mask_t mask;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+	host->dma_chan = dma_request_channel(mask, lpc32xx_dma_filter, NULL);
+	if (!host->dma_chan) {
+		dev_err(mtd->dev.parent, "Failed to request DMA channel\n");
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev)
+{
+	struct lpc32xx_nand_cfg_slc *pdata;
+	struct device_node *np = dev->of_node;
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata) {
+		dev_err(dev, "could not allocate memory for platform data\n");
+		return NULL;
+	}
+
+	of_property_read_u32(np, "nxp,wdr-clks", &pdata->wdr_clks);
+	of_property_read_u32(np, "nxp,wwidth", &pdata->wwidth);
+	of_property_read_u32(np, "nxp,whold", &pdata->whold);
+	of_property_read_u32(np, "nxp,wsetup", &pdata->wsetup);
+	of_property_read_u32(np, "nxp,rdr-clks", &pdata->rdr_clks);
+	of_property_read_u32(np, "nxp,rwidth", &pdata->rwidth);
+	of_property_read_u32(np, "nxp,rhold", &pdata->rhold);
+	of_property_read_u32(np, "nxp,rsetup", &pdata->rsetup);
+
+	if (!pdata->wdr_clks || !pdata->wwidth || !pdata->whold ||
+	    !pdata->wsetup || !pdata->rdr_clks || !pdata->rwidth ||
+	    !pdata->rhold || !pdata->rsetup) {
+		dev_err(dev, "chip parameters not specified correctly\n");
+		return NULL;
+	}
+
+	pdata->use_bbt = of_get_nand_on_flash_bbt(np);
+	pdata->wp_gpio = of_get_named_gpio_flags(np, "gpios", 0, NULL);
+
+	return pdata;
+}
+#else
+static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev)
+{
+	return NULL;
+}
+#endif
+
+/*
+ * Probe for NAND controller
+ */
+static int __devinit lpc32xx_nand_probe(struct platform_device *pdev)
+{
+	struct lpc32xx_nand_host *host;
+	struct mtd_info *mtd;
+	struct nand_chip *chip;
+	struct resource *rc;
+	struct mtd_part_parser_data ppdata = {};
+	int res;
+
+	rc = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (rc == NULL) {
+		dev_err(&pdev->dev, "No memory resource found for device\n");
+		return -EBUSY;
+	}
+
+	/* Allocate memory for the device structure (and zero it) */
+	host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
+	if (!host) {
+		dev_err(&pdev->dev, "failed to allocate device structure\n");
+		return -ENOMEM;
+	}
+	host->io_base_dma = rc->start;
+
+	host->io_base = devm_request_and_ioremap(&pdev->dev, rc);
+	if (host->io_base == NULL) {
+		dev_err(&pdev->dev, "ioremap failed\n");
+		return -ENOMEM;
+	}
+
+	if (pdev->dev.of_node)
+		host->ncfg = lpc32xx_parse_dt(&pdev->dev);
+	else
+		host->ncfg = pdev->dev.platform_data;
+	if (!host->ncfg) {
+		dev_err(&pdev->dev, "Missing platform data\n");
+		return -ENOENT;
+	}
+	if (gpio_request(host->ncfg->wp_gpio, "NAND WP")) {
+		dev_err(&pdev->dev, "GPIO not available\n");
+		return -EBUSY;
+	}
+	lpc32xx_wp_disable(host);
+
+	mtd = &host->mtd;
+	chip = &host->nand_chip;
+	chip->priv = host;
+	mtd->priv = chip;
+	mtd->owner = THIS_MODULE;
+	mtd->dev.parent = &pdev->dev;
+
+	/* Get NAND clock */
+	host->clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(host->clk)) {
+		dev_err(&pdev->dev, "Clock failure\n");
+		res = -ENOENT;
+		goto err_exit1;
+	}
+	clk_enable(host->clk);
+
+	/* Set NAND IO addresses and command/ready functions */
+	chip->IO_ADDR_R = SLC_DATA(host->io_base);
+	chip->IO_ADDR_W = SLC_DATA(host->io_base);
+	chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl;
+	chip->dev_ready = lpc32xx_nand_device_ready;
+	chip->chip_delay = 20; /* 20us command delay time */
+
+	/* Init NAND controller */
+	lpc32xx_nand_setup(host);
+
+	platform_set_drvdata(pdev, host);
+
+	/* NAND callbacks for LPC32xx SLC hardware */
+	chip->ecc.mode = NAND_ECC_HW_SYNDROME;
+	chip->read_byte = lpc32xx_nand_read_byte;
+	chip->read_buf = lpc32xx_nand_read_buf;
+	chip->write_buf = lpc32xx_nand_write_buf;
+	chip->ecc.read_page_raw = lpc32xx_nand_read_page_raw_syndrome;
+	chip->ecc.read_page = lpc32xx_nand_read_page_syndrome;
+	chip->ecc.write_page_raw = lpc32xx_nand_write_page_raw_syndrome;
+	chip->ecc.write_page = lpc32xx_nand_write_page_syndrome;
+	chip->ecc.write_oob = lpc32xx_nand_write_oob_syndrome;
+	chip->ecc.read_oob = lpc32xx_nand_read_oob_syndrome;
+	chip->ecc.calculate = lpc32xx_nand_ecc_calculate;
+	chip->ecc.correct = nand_correct_data;
+	chip->ecc.strength = 1;
+	chip->ecc.hwctl = lpc32xx_nand_ecc_enable;
+	chip->verify_buf = lpc32xx_verify_buf;
+
+	/* bitflip_threshold's default is defined as ecc_strength anyway.
+	 * Unfortunately, it is set only later at add_mtd_device(). Meanwhile
+	 * being 0, it causes bad block table scanning errors in
+	 * nand_scan_tail(), so preparing it here already. */
+	mtd->bitflip_threshold = chip->ecc.strength;
+
+	/*
+	 * Allocate a large enough buffer for a single huge page plus
+	 * extra space for the spare area and ECC storage area
+	 */
+	host->dma_buf_len = LPC32XX_DMA_DATA_SIZE + LPC32XX_ECC_SAVE_SIZE;
+	host->data_buf = devm_kzalloc(&pdev->dev, host->dma_buf_len,
+				      GFP_KERNEL);
+	if (host->data_buf == NULL) {
+		dev_err(&pdev->dev, "Error allocating memory\n");
+		res = -ENOMEM;
+		goto err_exit2;
+	}
+
+	res = lpc32xx_nand_dma_setup(host);
+	if (res) {
+		res = -EIO;
+		goto err_exit2;
+	}
+
+	/* Find NAND device */
+	if (nand_scan_ident(mtd, 1, NULL)) {
+		res = -ENXIO;
+		goto err_exit3;
+	}
+
+	/* OOB and ECC CPU and DMA work areas */
+	host->ecc_buf = (u32 *)(host->data_buf + LPC32XX_DMA_DATA_SIZE);
+
+	/*
+	 * Small page FLASH has a unique OOB layout, but large and huge
+	 * page FLASH use the standard layout. Small page FLASH uses a
+	 * custom BBT marker layout.
+	 */
+	if (mtd->writesize <= 512)
+		chip->ecc.layout = &lpc32xx_nand_oob_16;
+
+	/* These sizes remain the same regardless of page size */
+	chip->ecc.size = 256;
+	chip->ecc.bytes = LPC32XX_SLC_DEV_ECC_BYTES;
+	chip->ecc.prepad = chip->ecc.postpad = 0;
+
+	/* Avoid extra scan if using BBT, setup BBT support */
+	if (host->ncfg->use_bbt) {
+		chip->options |= NAND_SKIP_BBTSCAN;
+		chip->bbt_options |= NAND_BBT_USE_FLASH;
+
+		/*
+		 * Use a custom BBT marker setup for small page FLASH that
+		 * won't interfere with the ECC layout. Large and huge page
+		 * FLASH use the standard layout.
+		 */
+		if (mtd->writesize <= 512) {
+			chip->bbt_td = &bbt_smallpage_main_descr;
+			chip->bbt_md = &bbt_smallpage_mirror_descr;
+		}
+	}
+
+	/*
+	 * Fills out all the uninitialized function pointers with the defaults
+	 */
+	if (nand_scan_tail(mtd)) {
+		res = -ENXIO;
+		goto err_exit3;
+	}
+
+	/* Standard layout in FLASH for bad block tables */
+	if (host->ncfg->use_bbt) {
+		if (nand_default_bbt(mtd) < 0)
+			dev_err(&pdev->dev,
+			       "Error initializing default bad block tables\n");
+	}
+
+	mtd->name = "nxp_lpc3220_slc";
+	ppdata.of_node = pdev->dev.of_node;
+	res = mtd_device_parse_register(mtd, NULL, &ppdata, host->ncfg->parts,
+					host->ncfg->num_parts);
+	if (!res)
+		return res;
+
+	nand_release(mtd);
+
+err_exit3:
+	dma_release_channel(host->dma_chan);
+err_exit2:
+	clk_disable(host->clk);
+	clk_put(host->clk);
+	platform_set_drvdata(pdev, NULL);
+err_exit1:
+	lpc32xx_wp_enable(host);
+	gpio_free(host->ncfg->wp_gpio);
+
+	return res;
+}
+
+/*
+ * Remove NAND device.
+ */
+static int __devexit lpc32xx_nand_remove(struct platform_device *pdev)
+{
+	u32 tmp;
+	struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
+	struct mtd_info *mtd = &host->mtd;
+
+	nand_release(mtd);
+	dma_release_channel(host->dma_chan);
+
+	/* Force CE high */
+	tmp = readl(SLC_CTRL(host->io_base));
+	tmp &= ~SLCCFG_CE_LOW;
+	writel(tmp, SLC_CTRL(host->io_base));
+
+	clk_disable(host->clk);
+	clk_put(host->clk);
+	platform_set_drvdata(pdev, NULL);
+	lpc32xx_wp_enable(host);
+	gpio_free(host->ncfg->wp_gpio);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int lpc32xx_nand_resume(struct platform_device *pdev)
+{
+	struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
+
+	/* Re-enable NAND clock */
+	clk_enable(host->clk);
+
+	/* Fresh init of NAND controller */
+	lpc32xx_nand_setup(host);
+
+	/* Disable write protect */
+	lpc32xx_wp_disable(host);
+
+	return 0;
+}
+
+static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm)
+{
+	u32 tmp;
+	struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
+
+	/* Force CE high */
+	tmp = readl(SLC_CTRL(host->io_base));
+	tmp &= ~SLCCFG_CE_LOW;
+	writel(tmp, SLC_CTRL(host->io_base));
+
+	/* Enable write protect for safety */
+	lpc32xx_wp_enable(host);
+
+	/* Disable clock */
+	clk_disable(host->clk);
+
+	return 0;
+}
+
+#else
+#define lpc32xx_nand_resume NULL
+#define lpc32xx_nand_suspend NULL
+#endif
+
+#if defined(CONFIG_OF)
+static const struct of_device_id lpc32xx_nand_match[] = {
+	{ .compatible = "nxp,lpc3220-slc" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, lpc32xx_nand_match);
+#endif
+
+static struct platform_driver lpc32xx_nand_driver = {
+	.probe		= lpc32xx_nand_probe,
+	.remove		= __devexit_p(lpc32xx_nand_remove),
+	.resume		= lpc32xx_nand_resume,
+	.suspend	= lpc32xx_nand_suspend,
+	.driver		= {
+		.name	= LPC32XX_MODNAME,
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(lpc32xx_nand_match),
+	},
+};
+
+module_platform_driver(lpc32xx_nand_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>");
+MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
+MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX SLC controller");

[PATCH v4] MTD: LPC32xx MLC NAND driver

[Roland Stigge]

This patch adds a driver for the MLC NAND controller of the LPC32xx SoC.

Signed-off-by: Roland Stigge <stigge-uj/7R2tJ6VmzQB+pC5nmwQ@public.gmane.org>

---
Applies to v3.5-rc1 + LPC32xx SLC NAND driver (Kconfig + Makefile)

Changes since v3:
* Dropped superfluous error handling of dmaengine_submit()
* Added unmapping of dma sg buffers

Changes since v2:
* Adjusted to mtd API changes

Changes since v1:
* Factored out dmaengine_slave_config() to dma_setup() function in probe()
* Fixed dma data direction and dma transfer direction differences
* Removed dma_sync_sg_for_cpu() - not necessary due to unmap
* Removed dma_set_mask()

Thanks to Russell King for reviewing!

 Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt |   50 
 drivers/mtd/nand/Kconfig                              |   13 
 drivers/mtd/nand/Makefile                             |    1 
 drivers/mtd/nand/lpc32xx_nand_mlc.c                   |  963 ++++++++++++++++++
 4 files changed, 1026 insertions(+), 1 deletion(-)

--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt
@@ -0,0 +1,50 @@
+NXP LPC32xx SoC NAND MLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-mlc"
+- reg: Address and size of the controller
+- interrupts: The NAND interrupt specification
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in
+Hz, to make them independent of actual clock speed and to provide for good
+accuracy:)
+- nxp,tcea_delay: TCEA_DELAY
+- nxp,busy_delay: BUSY_DELAY
+- nxp,nand_ta: NAND_TA
+- nxp,rd_high: RD_HIGH
+- nxp,rd_low: RD_LOW
+- nxp,wr_high: WR_HIGH
+- nxp,wr_low: WR_LOW
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	mlc: flash@200A8000 {
+		compatible = "nxp,lpc3220-mlc";
+		reg = <0x200A8000 0x11000>;
+		interrupts = <11 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,tcea-delay = <333333333>;
+		nxp,busy-delay = <10000000>;
+		nxp,nand-ta = <18181818>;
+		nxp,rd-high = <31250000>;
+		nxp,rd-low = <45454545>;
+		nxp,wr-high = <40000000>;
+		nxp,wr-low = <83333333>;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};
--- linux-2.6.orig/drivers/mtd/nand/Kconfig
+++ linux-2.6/drivers/mtd/nand/Kconfig
@@ -455,7 +455,7 @@ config MTD_NAND_PXA3xx
 	  PXA3xx processors
 
 config MTD_NAND_SLC_LPC32XX
-	bool "NXP LPC32xx SLC Controller"
+	tristate "NXP LPC32xx SLC Controller"
 	depends on ARCH_LPC32XX
 	help
 	  Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
@@ -465,6 +465,17 @@ config MTD_NAND_SLC_LPC32XX
 	  Please check the actual NAND chip connected and its support
 	  by the SLC NAND controller.
 
+config MTD_NAND_MLC_LPC32XX
+       tristate "NXP LPC32xx MLC Controller"
+       depends on ARCH_LPC32XX
+       help
+         Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
+         controller. This is the default for the WORK92105 controller
+         board.
+
+         Please check the actual NAND chip connected and its support
+         by the MLC NAND controller.
+
 config MTD_NAND_CM_X270
 	tristate "Support for NAND Flash on CM-X270 modules"
 	depends on MACH_ARMCORE
--- linux-2.6.orig/drivers/mtd/nand/Makefile
+++ linux-2.6/drivers/mtd/nand/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_MTD_NAND_FSL_ELBC)		+= fsl_
 obj-$(CONFIG_MTD_NAND_FSL_IFC)		+= fsl_ifc_nand.o
 obj-$(CONFIG_MTD_NAND_FSL_UPM)		+= fsl_upm.o
 obj-$(CONFIG_MTD_NAND_SLC_LPC32XX)      += lpc32xx_nand_slc.o
+obj-$(CONFIG_MTD_NAND_MLC_LPC32XX)      += lpc32xx_nand_mlc.o
 obj-$(CONFIG_MTD_NAND_SH_FLCTL)		+= sh_flctl.o
 obj-$(CONFIG_MTD_NAND_MXC)		+= mxc_nand.o
 obj-$(CONFIG_MTD_NAND_SOCRATES)		+= socrates_nand.o
--- /dev/null
+++ linux-2.6/drivers/mtd/nand/lpc32xx_nand_mlc.c
@@ -0,0 +1,963 @@
+/*
+ * Driver for NAND MLC Controller in LPC32xx
+ *
+ * Author: Roland Stigge <stigge-uj/7R2tJ6VmzQB+pC5nmwQ@public.gmane.org>
+ *
+ * Copyright (C) 2011 WORK Microwave GmbH
+ * Copyright (C) 2011, 2012 Roland Stigge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *
+ * NAND Flash Controller Operation:
+ * - Read: Auto Decode
+ * - Write: Auto Encode
+ * - Page Size: Large Page (2112 Bytes) only for now
+ */
+
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/completion.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/of_mtd.h>
+#include <linux/of_gpio.h>
+#include <linux/amba/pl08x.h>
+#include <linux/io.h>
+#include <linux/mm.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/mtd/nand_ecc.h>
+
+#define DRV_NAME "lpc32xx_nand_mlc"
+
+#define NAND_LARGE_BLOCK_PAGE_SIZE      2048
+#define NAND_SMALL_BLOCK_PAGE_SIZE      512
+
+#define NAND_ERASED_BLOCK_ECC_VALUE	0xFFFFFFFF
+
+/**********************************************************************
+* MLC NAND controller register offsets
+**********************************************************************/
+
+#define MLC_BUFF(x)			(x + 0x00000)
+#define MLC_DATA(x)			(x + 0x08000)
+#define MLC_CMD(x)			(x + 0x10000)
+#define MLC_ADDR(x)			(x + 0x10004)
+#define MLC_ECC_ENC_REG(x)		(x + 0x10008)
+#define MLC_ECC_DEC_REG(x)		(x + 0x1000C)
+#define MLC_ECC_AUTO_ENC_REG(x)		(x + 0x10010)
+#define MLC_ECC_AUTO_DEC_REG(x)		(x + 0x10014)
+#define MLC_RPR(x)			(x + 0x10018)
+#define MLC_WPR(x)			(x + 0x1001C)
+#define MLC_RUBP(x)			(x + 0x10020)
+#define MLC_ROBP(x)			(x + 0x10024)
+#define MLC_SW_WP_ADD_LOW(x)		(x + 0x10028)
+#define MLC_SW_WP_ADD_HIG(x)		(x + 0x1002C)
+#define MLC_ICR(x)			(x + 0x10030)
+#define MLC_TIME_REG(x)			(x + 0x10034)
+#define MLC_IRQ_MR(x)			(x + 0x10038)
+#define MLC_IRQ_SR(x)			(x + 0x1003C)
+#define MLC_LOCK_PR(x)			(x + 0x10044)
+#define MLC_ISR(x)			(x + 0x10048)
+#define MLC_CEH(x)			(x + 0x1004C)
+
+/**********************************************************************
+* MLC_CMD bit definitions
+**********************************************************************/
+#define MLCCMD_RESET			0xFF
+
+/**********************************************************************
+* MLC_ICR bit definitions
+**********************************************************************/
+#define MLCICR_WPROT			(1 << 3)
+#define MLCICR_LARGEBLOCK		(1 << 2)
+#define MLCICR_LONGADDR			(1 << 1)
+#define MLCICR_16BIT			(1 << 0)  /* unsupported by LPC32x0! */
+
+/**********************************************************************
+* MLC_TIME_REG bit definitions
+**********************************************************************/
+#define MLCTIMEREG_TCEA_DELAY(n)	(((n) & 0x03) << 24)
+#define MLCTIMEREG_BUSY_DELAY(n)	(((n) & 0x1F) << 19)
+#define MLCTIMEREG_NAND_TA(n)		(((n) & 0x07) << 16)
+#define MLCTIMEREG_RD_HIGH(n)		(((n) & 0x0F) << 12)
+#define MLCTIMEREG_RD_LOW(n)		(((n) & 0x0F) << 8)
+#define MLCTIMEREG_WR_HIGH(n)		(((n) & 0x0F) << 4)
+#define MLCTIMEREG_WR_LOW(n)		(((n) & 0x0F) << 0)
+
+/**********************************************************************
+* MLC_IRQ_MR and MLC_IRQ_SR bit definitions
+**********************************************************************/
+#define MLCIRQ_NAND_READY		(1 << 5)
+#define MLCIRQ_CONTROLLER_READY		(1 << 4)
+#define MLCIRQ_DECODE_FAILURE		(1 << 3)
+#define MLCIRQ_DECODE_ERROR		(1 << 2)
+#define MLCIRQ_ECC_READY		(1 << 1)
+#define MLCIRQ_WRPROT_FAULT		(1 << 0)
+
+/**********************************************************************
+* MLC_LOCK_PR bit definitions
+**********************************************************************/
+#define MLCLOCKPR_MAGIC			0xA25E
+
+/**********************************************************************
+* MLC_ISR bit definitions
+**********************************************************************/
+#define MLCISR_DECODER_FAILURE		(1 << 6)
+#define MLCISR_ERRORS			((1 << 4) | (1 << 5))
+#define MLCISR_ERRORS_DETECTED		(1 << 3)
+#define MLCISR_ECC_READY		(1 << 2)
+#define MLCISR_CONTROLLER_READY		(1 << 1)
+#define MLCISR_NAND_READY		(1 << 0)
+
+/**********************************************************************
+* MLC_CEH bit definitions
+**********************************************************************/
+#define MLCCEH_NORMAL			(1 << 0)
+
+struct lpc32xx_nand_cfg_mlc {
+	u32 tcea_delay;
+	u32 busy_delay;
+	u32 nand_ta;
+	u32 rd_high;
+	u32 rd_low;
+	u32 wr_high;
+	u32 wr_low;
+	unsigned wp_gpio;
+	struct mtd_partition *parts;
+	unsigned num_parts;
+};
+
+static struct nand_ecclayout lpc32xx_nand_oob = {
+	.eccbytes = 40,
+	.eccpos = { 6,  7,  8,  9, 10, 11, 12, 13, 14, 15,
+		   22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
+		   38, 39, 40, 41, 42, 43, 44, 45, 46, 47,
+		   54, 55, 56, 57, 58, 59, 60, 61, 62, 63 },
+	.oobfree = {
+		{ .offset = 0,
+		  .length = 6, },
+		{ .offset = 16,
+		  .length = 6, },
+		{ .offset = 32,
+		  .length = 6, },
+		{ .offset = 48,
+		  .length = 6, },
+		},
+};
+
+static struct nand_bbt_descr lpc32xx_nand_bbt = {
+	.options = NAND_BBT_ABSPAGE | NAND_BBT_2BIT | NAND_BBT_NO_OOB |
+		   NAND_BBT_WRITE,
+	.pages = { 524224, 0, 0, 0, 0, 0, 0, 0 },
+};
+
+static struct nand_bbt_descr lpc32xx_nand_bbt_mirror = {
+	.options = NAND_BBT_ABSPAGE | NAND_BBT_2BIT | NAND_BBT_NO_OOB |
+		   NAND_BBT_WRITE,
+	.pages = { 524160, 0, 0, 0, 0, 0, 0, 0 },
+};
+
+struct lpc32xx_nand_host {
+	struct nand_chip	nand_chip;
+	struct clk		*clk;
+	struct mtd_info		mtd;
+	void __iomem		*io_base;
+	int			irq;
+	struct lpc32xx_nand_cfg_mlc	*ncfg;
+	struct completion       comp_nand;
+	struct completion       comp_controller;
+	uint32_t llptr;
+	/*
+	 * Physical addresses of ECC buffer, DMA data buffers, OOB data buffer
+	 */
+	dma_addr_t		oob_buf_phy;
+	/*
+	 * Virtual addresses of ECC buffer, DMA data buffers, OOB data buffer
+	 */
+	uint8_t			*oob_buf;
+	/* Physical address of DMA base address */
+	dma_addr_t		io_base_phy;
+
+	struct completion	comp_dma;
+	struct dma_chan		*dma_chan;
+	struct dma_slave_config	dma_slave_config;
+	struct scatterlist	sgl;
+	u8			*dma_buf;
+};
+
+/*
+ * Activate/Deactivate DMA Operation:
+ *
+ * Using the PL080 DMA Controller for transferring the 512 byte subpages
+ * instead of doing readl() / writel() in a loop slows it down significantly.
+ * Measurements via getnstimeofday() upon 512 byte subpage reads reveal:
+ *
+ * - readl() of 128 x 32 bits in a loop: ~20us
+ * - DMA read of 512 bytes (32 bit, 4...128 words bursts): ~60us
+ * - DMA read of 512 bytes (32 bit, no bursts): ~100us
+ *
+ * This applies to the transfer itself. In the DMA case: only the
+ * wait_for_completion() (DMA setup _not_ included).
+ *
+ * Note that the 512 bytes subpage transfer is done directly from/to a
+ * FIFO/buffer inside the NAND controller. Most of the time (~400-800us for a
+ * 2048 bytes page) is spent waiting for the NAND IRQ, anyway. (The NAND
+ * controller transferring data between its internal buffer to/from the NAND
+ * chip.)
+ *
+ * Therefore, using the PL080 DMA is disabled by default, for now.
+ *
+ */
+static int use_dma = 0;
+
+static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host)
+{
+	u32 clkrate, tmp;
+
+	/* Reset MLC controller */
+	writel(MLCCMD_RESET, MLC_CMD(host->io_base));
+	udelay(1000);
+
+	/* Get base clock for MLC block */
+	clkrate = clk_get_rate(host->clk);
+	if (clkrate == 0)
+		clkrate = 104000000;
+
+	/* Unlock MLC_ICR
+	 * (among others, will be locked again automatically) */
+	writew(MLCLOCKPR_MAGIC, MLC_LOCK_PR(host->io_base));
+
+	/* Configure MLC Controller: Large Block, 5 Byte Address */
+	tmp = MLCICR_LARGEBLOCK | MLCICR_LONGADDR;
+	writel(tmp, MLC_ICR(host->io_base));
+
+	/* Unlock MLC_TIME_REG
+	 * (among others, will be locked again automatically) */
+	writew(MLCLOCKPR_MAGIC, MLC_LOCK_PR(host->io_base));
+
+	/* Compute clock setup values, see LPC and NAND manual */
+	tmp = 0;
+	tmp |= MLCTIMEREG_TCEA_DELAY(clkrate / host->ncfg->tcea_delay + 1);
+	tmp |= MLCTIMEREG_BUSY_DELAY(clkrate / host->ncfg->busy_delay + 1);
+	tmp |= MLCTIMEREG_NAND_TA(clkrate / host->ncfg->nand_ta + 1);
+	tmp |= MLCTIMEREG_RD_HIGH(clkrate / host->ncfg->rd_high + 1);
+	tmp |= MLCTIMEREG_RD_LOW(clkrate / host->ncfg->rd_low);
+	tmp |= MLCTIMEREG_WR_HIGH(clkrate / host->ncfg->wr_high + 1);
+	tmp |= MLCTIMEREG_WR_LOW(clkrate / host->ncfg->wr_low);
+	writel(tmp, MLC_TIME_REG(host->io_base));
+
+	/* Enable IRQ for CONTROLLER_READY and NAND_READY */
+	writeb(MLCIRQ_CONTROLLER_READY | MLCIRQ_NAND_READY,
+			MLC_IRQ_MR(host->io_base));
+
+	/* Normal nCE operation: nCE controlled by controller */
+	writel(MLCCEH_NORMAL, MLC_CEH(host->io_base));
+}
+
+/*
+ * Hardware specific access to control lines
+ */
+static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+				  unsigned int ctrl)
+{
+	struct nand_chip *nand_chip = mtd->priv;
+	struct lpc32xx_nand_host *host = nand_chip->priv;
+
+	if (cmd != NAND_CMD_NONE) {
+		if (ctrl & NAND_CLE)
+			writel(cmd, MLC_CMD(host->io_base));
+		else
+			writel(cmd, MLC_ADDR(host->io_base));
+	}
+}
+
+/*
+ * Read Device Ready (NAND device _and_ controller ready)
+ */
+static int lpc32xx_nand_device_ready(struct mtd_info *mtd)
+{
+	struct nand_chip *nand_chip = mtd->priv;
+	struct lpc32xx_nand_host *host = nand_chip->priv;
+
+	if ((readb(MLC_ISR(host->io_base)) &
+	     (MLCISR_CONTROLLER_READY | MLCISR_NAND_READY)) ==
+	    (MLCISR_CONTROLLER_READY | MLCISR_NAND_READY))
+		return  1;
+
+	return 0;
+}
+
+static irqreturn_t lpc3xxx_nand_irq(int irq, struct lpc32xx_nand_host *host)
+{
+	uint8_t sr;
+
+	/* Clear interrupt flag by reading status */
+	sr = readb(MLC_IRQ_SR(host->io_base));
+	if (sr & MLCIRQ_NAND_READY)
+		complete(&host->comp_nand);
+	if (sr & MLCIRQ_CONTROLLER_READY)
+		complete(&host->comp_controller);
+
+	return IRQ_HANDLED;
+}
+
+static int lpc32xx_waitfunc_nand(struct mtd_info *mtd, struct nand_chip *chip)
+{
+	struct lpc32xx_nand_host *host = chip->priv;
+
+	if (readb(MLC_ISR(host->io_base)) & MLCISR_NAND_READY)
+		goto exit;
+
+	wait_for_completion(&host->comp_nand);
+
+	while (!(readb(MLC_ISR(host->io_base)) & MLCISR_NAND_READY)) {
+		/* Seems to be delayed sometimes by controller */
+		dev_dbg(&mtd->dev, "Warning: NAND not ready.\n");
+		cpu_relax();
+	}
+
+exit:
+	return NAND_STATUS_READY;
+}
+
+static int lpc32xx_waitfunc_controller(struct mtd_info *mtd,
+				       struct nand_chip *chip)
+{
+	struct lpc32xx_nand_host *host = chip->priv;
+
+	if (readb(MLC_ISR(host->io_base)) & MLCISR_CONTROLLER_READY)
+		goto exit;
+
+	wait_for_completion(&host->comp_controller);
+
+	while (!(readb(MLC_ISR(host->io_base)) &
+		 MLCISR_CONTROLLER_READY)) {
+		dev_dbg(&mtd->dev, "Warning: Controller not ready.\n");
+		cpu_relax();
+	}
+
+exit:
+	return NAND_STATUS_READY;
+}
+
+static int lpc32xx_waitfunc(struct mtd_info *mtd, struct nand_chip *chip)
+{
+	lpc32xx_waitfunc_nand(mtd, chip);
+	lpc32xx_waitfunc_controller(mtd, chip);
+
+	return NAND_STATUS_READY;
+}
+
+/*
+ * Enable NAND write protect
+ */
+static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host)
+{
+	gpio_set_value(host->ncfg->wp_gpio, 0);
+}
+
+/*
+ * Disable NAND write protect
+ */
+static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
+{
+	gpio_set_value(host->ncfg->wp_gpio, 1);
+}
+
+static uint8_t lpc32xx_read_byte(struct mtd_info *mtd)
+{
+	struct nand_chip *nand_chip = mtd->priv;
+	struct lpc32xx_nand_host *host = nand_chip->priv;
+
+	return readb(MLC_DATA(host->io_base));
+}
+
+static void lpc32xx_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+	int i;
+	struct nand_chip *nand_chip = mtd->priv;
+	struct lpc32xx_nand_host *host = nand_chip->priv;
+
+	/* We are supposed to write only via the buffered auto encode */
+	dev_warn(&mtd->dev,
+		 "Warning: %s(): Writing %d bytes. This shouldn't happen!\n",
+		 __func__, len);
+
+	for (i = 0; i < len; i++)
+		writeb(buf[i], MLC_DATA(host->io_base));
+}
+
+static void lpc32xx_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+	int i;
+	struct nand_chip *nand_chip = mtd->priv;
+	struct lpc32xx_nand_host *host = nand_chip->priv;
+
+	dev_warn(&mtd->dev,
+		 "Warning: %s(): Reading %d bytes. This shouldn't happen!\n",
+		 __func__, len);
+
+	for (i = 0; i < len; i++)
+		buf[i] = readb(MLC_DATA(host->io_base));
+}
+
+static void lpc32xx_dma_complete_func(void *completion)
+{
+	complete(completion);
+}
+
+static int lpc32xx_xmit_dma(struct mtd_info *mtd, void *mem, int len,
+			    enum dma_transfer_direction dir)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct lpc32xx_nand_host *host = chip->priv;
+	struct dma_async_tx_descriptor *desc;
+	int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+	int res;
+
+	sg_init_one(&host->sgl, mem, len);
+
+	res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1,
+			 DMA_BIDIRECTIONAL);
+	if (res != 1) {
+		dev_err(mtd->dev.parent, "Failed to map sg list\n");
+		return -ENXIO;
+	}
+	desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir,
+				       flags);
+	if (!desc) {
+		dev_err(mtd->dev.parent, "Failed to prepare slave sg\n");
+		goto out1;
+	}
+
+	init_completion(&host->comp_dma);
+	desc->callback = lpc32xx_dma_complete_func;
+	desc->callback_param = &host->comp_dma;
+
+	dmaengine_submit(desc);
+	dma_async_issue_pending(host->dma_chan);
+
+	wait_for_completion_timeout(&host->comp_dma, msecs_to_jiffies(1000));
+
+	dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1,
+		     DMA_BIDIRECTIONAL);
+	return 0;
+out1:
+	dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1,
+		     DMA_BIDIRECTIONAL);
+	return -ENXIO;
+}
+
+static int lpc32xx_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+			     uint8_t *buf, int oob_required, int page)
+{
+	struct lpc32xx_nand_host *host = chip->priv;
+	int i, j;
+	uint8_t *oobbuf = chip->oob_poi;
+	u32 mlc_isr;
+	int res;
+	u8 *dma_buf;
+	bool dma_mapped;
+
+	if ((void *)buf <= high_memory) {
+		dma_buf = buf;
+		dma_mapped = true;
+	} else {
+		dma_buf = host->dma_buf;
+		dma_mapped = false;
+	}
+
+	/* Writing Command and Address */
+	chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+
+	/* For all sub-pages */
+	for (i = 0; i < 4; i++) {
+		/* Start Auto Decode Command */
+		writeb(0x00, MLC_ECC_AUTO_DEC_REG(host->io_base));
+
+		/* Wait for Controller Ready */
+		lpc32xx_waitfunc_controller(mtd, chip);
+
+		/* Check ECC Error status */
+		mlc_isr = readl(MLC_ISR(host->io_base));
+		if (mlc_isr & MLCISR_DECODER_FAILURE) {
+			mtd->ecc_stats.failed++;
+			dev_warn(&mtd->dev, "%s: DECODER_FAILURE\n", __func__);
+		} else if (mlc_isr & MLCISR_ERRORS_DETECTED) {
+			mtd->ecc_stats.corrected += ((mlc_isr >> 4) & 0x3) + 1;
+		}
+
+		/* Read 512 + 16 Bytes */
+		if (use_dma) {
+			res = lpc32xx_xmit_dma(mtd, dma_buf + i * 512, 512,
+					       DMA_DEV_TO_MEM);
+			if (res)
+				return res;
+		} else {
+			for (j = 0; j < (512 >> 2); j++) {
+				*((uint32_t *)(buf)) =
+					readl(MLC_BUFF(host->io_base));
+				buf += 4;
+			}
+		}
+		for (j = 0; j < (16 >> 2); j++) {
+			*((uint32_t *)(oobbuf)) =
+				readl(MLC_BUFF(host->io_base));
+			oobbuf += 4;
+		}
+	}
+
+	if (use_dma && !dma_mapped)
+		memcpy(buf, dma_buf, NAND_LARGE_BLOCK_PAGE_SIZE);
+
+	return 0;
+}
+
+static void lpc32xx_write_page_lowlevel(struct mtd_info *mtd,
+					struct nand_chip *chip,
+					const uint8_t *buf, int oob_required)
+{
+	struct lpc32xx_nand_host *host = chip->priv;
+	const uint8_t *oobbuf = chip->oob_poi;
+	u8 *dma_buf;
+	int res;
+	int i, j;
+
+	if (use_dma) {
+		if ((void *)buf <= high_memory) {
+			dma_buf = (u8 *)buf;
+		} else {
+			dma_buf = host->dma_buf;
+			memcpy(dma_buf, buf, NAND_LARGE_BLOCK_PAGE_SIZE);
+		}
+	}
+
+	for (i = 0; i < 4; i++) {
+		/* Start Encode */
+		writeb(0x00, MLC_ECC_ENC_REG(host->io_base));
+
+		/* Write 512 + 6 Bytes to Buffer */
+		if (use_dma) {
+			res = lpc32xx_xmit_dma(mtd, dma_buf + i * 512, 512,
+					       DMA_MEM_TO_DEV);
+			if (res)
+				return;
+		} else {
+			for (j = 0; j < (512 >> 2); j++) {
+				writel(*((uint32_t *)(buf)),
+				       MLC_BUFF(host->io_base));
+				buf += 4;
+			}
+		}
+		writel(*((uint32_t *)(oobbuf)), MLC_BUFF(host->io_base));
+		oobbuf += 4;
+		writew(*((uint16_t *)(oobbuf)), MLC_BUFF(host->io_base));
+		oobbuf += 12;
+
+		/* Auto Encode w/ Bit 8 = 0 (see LPC MLC Controller manual) */
+		writeb(0x00, MLC_ECC_AUTO_ENC_REG(host->io_base));
+
+		/* Wait for Controller Ready */
+		lpc32xx_waitfunc_controller(mtd, chip);
+	}
+}
+
+static int lpc32xx_write_page(struct mtd_info *mtd, struct nand_chip *chip,
+			      const uint8_t *buf, int oob_required, int page,
+			      int cached, int raw)
+{
+	chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
+	lpc32xx_write_page_lowlevel(mtd, chip, buf, oob_required);
+	chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+	lpc32xx_waitfunc(mtd, chip);
+
+	return 0;
+}
+
+static int lpc32xx_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			    int page)
+{
+	uint8_t buf[NAND_LARGE_BLOCK_PAGE_SIZE];
+
+	/* Read whole page - necessary with MLC controller! */
+	lpc32xx_read_page(mtd, chip, buf, 1, page);
+
+	return 0;
+}
+
+static int lpc32xx_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			      int page)
+{
+	/* None, write_oob conflicts with the automatic LPC MLC ECC decoder! */
+	return 0;
+}
+
+/* Prepares MLC for transfers with H/W ECC enabled: always enabled anyway */
+static void lpc32xx_ecc_enable(struct mtd_info *mtd, int mode)
+{
+	/* Always enabled! */
+}
+
+static bool lpc32xx_dma_filter(struct dma_chan *chan, void *param)
+{
+	struct pl08x_dma_chan *ch =
+		container_of(chan, struct pl08x_dma_chan, chan);
+
+	/* In LPC32xx's PL080 DMA wiring, the MLC NAND DMA signal is #12 */
+	if (ch->cd->min_signal == 12)
+		return true;
+	return false;
+}
+
+static int lpc32xx_dma_setup(struct lpc32xx_nand_host *host)
+{
+	struct mtd_info *mtd = &host->mtd;
+	dma_cap_mask_t mask;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+	host->dma_chan = dma_request_channel(mask, lpc32xx_dma_filter, NULL);
+	if (!host->dma_chan) {
+		dev_err(mtd->dev.parent, "Failed to request DMA channel\n");
+		return -EBUSY;
+	}
+
+	/*
+	 * Set direction to a sensible value even if the dmaengine driver
+	 * should ignore it. With the default (DMA_MEM_TO_MEM), the amba-pl08x
+	 * driver criticizes it as "alien transfer direction".
+	 */
+	host->dma_slave_config.direction = DMA_DEV_TO_MEM;
+	host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	host->dma_slave_config.src_maxburst = 128;
+	host->dma_slave_config.dst_maxburst = 128;
+	/* DMA controller does flow control: */
+	host->dma_slave_config.device_fc = false;
+	host->dma_slave_config.src_addr = MLC_BUFF(host->io_base_phy);
+	host->dma_slave_config.dst_addr = MLC_BUFF(host->io_base_phy);
+	if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) {
+		dev_err(mtd->dev.parent, "Failed to setup DMA slave\n");
+		goto out1;
+	}
+
+	return 0;
+out1:
+	dma_release_channel(host->dma_chan);
+	return -ENXIO;
+}
+
+#ifdef CONFIG_OF
+static struct lpc32xx_nand_cfg_mlc *lpc32xx_parse_dt(struct device *dev)
+{
+	struct lpc32xx_nand_cfg_mlc *pdata;
+	struct device_node *np = dev->of_node;
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata) {
+		dev_err(dev, "could not allocate memory for platform data\n");
+		return NULL;
+	}
+
+	of_property_read_u32(np, "nxp,tcea-delay", &pdata->tcea_delay);
+	of_property_read_u32(np, "nxp,busy-delay", &pdata->busy_delay);
+	of_property_read_u32(np, "nxp,nand-ta", &pdata->nand_ta);
+	of_property_read_u32(np, "nxp,rd-high", &pdata->rd_high);
+	of_property_read_u32(np, "nxp,rd-low", &pdata->rd_low);
+	of_property_read_u32(np, "nxp,wr-high", &pdata->wr_high);
+	of_property_read_u32(np, "nxp,wr-low", &pdata->wr_low);
+
+	if (!pdata->tcea_delay || !pdata->busy_delay || !pdata->nand_ta ||
+	    !pdata->rd_high || !pdata->rd_low || !pdata->wr_high ||
+	    !pdata->wr_low) {
+		dev_err(dev, "chip parameters not specified correctly\n");
+		return NULL;
+	}
+
+	pdata->wp_gpio = of_get_named_gpio_flags(np, "gpios", 0, NULL);
+
+	return pdata;
+}
+#else
+static struct lpc32xx_nand_cfg_mlc *lpc32xx_parse_dt(struct device *dev)
+{
+	return NULL;
+}
+#endif
+
+/*
+ * Probe for NAND controller
+ */
+static int __devinit lpc32xx_nand_probe(struct platform_device *pdev)
+{
+	struct lpc32xx_nand_host *host;
+	struct mtd_info *mtd;
+	struct nand_chip *nand_chip;
+	struct resource *rc;
+	int res;
+	uint8_t sr;
+	struct mtd_part_parser_data ppdata = {};
+
+	/* Allocate memory for the device structure (and zero it) */
+	host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
+	if (!host) {
+		dev_err(&pdev->dev, "failed to allocate device structure.\n");
+		return -ENOMEM;
+	}
+
+	rc = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (rc == NULL) {
+		dev_err(&pdev->dev, "No memory resource found for device!\r\n");
+		return -ENXIO;
+	}
+
+	host->io_base = devm_request_and_ioremap(&pdev->dev, rc);
+	if (host->io_base == NULL) {
+		dev_err(&pdev->dev, "ioremap failed\n");
+		return -EIO;
+	}
+	host->io_base_phy = rc->start;
+
+	mtd = &host->mtd;
+	nand_chip = &host->nand_chip;
+	if (pdev->dev.of_node)
+		host->ncfg = lpc32xx_parse_dt(&pdev->dev);
+	else
+		host->ncfg = pdev->dev.platform_data;
+	if (!host->ncfg) {
+		dev_err(&pdev->dev, "Missing platform data\n");
+		return -ENOENT;
+	}
+	if (gpio_request(host->ncfg->wp_gpio, "NAND WP")) {
+		dev_err(&pdev->dev, "GPIO not available\n");
+		return -EBUSY;
+	}
+	lpc32xx_wp_disable(host);
+
+	nand_chip->priv = host;		/* link the private data structures */
+	mtd->priv = nand_chip;
+	mtd->owner = THIS_MODULE;
+	mtd->dev.parent = &pdev->dev;
+
+	/* Get NAND clock */
+	host->clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(host->clk)) {
+		dev_err(&pdev->dev, "Clock initialization failure\n");
+		res = -ENOENT;
+		goto err_exit1;
+	}
+	clk_enable(host->clk);
+
+	nand_chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl;
+	nand_chip->dev_ready = lpc32xx_nand_device_ready;
+	nand_chip->chip_delay = 25; /* us */
+
+	/* Init NAND controller */
+	lpc32xx_nand_setup(host);
+
+	platform_set_drvdata(pdev, host);
+
+	/* Initialize function pointers */
+	nand_chip->read_byte = lpc32xx_read_byte;
+	nand_chip->read_buf = lpc32xx_read_buf;
+	nand_chip->write_buf = lpc32xx_write_buf;
+	nand_chip->ecc.hwctl = lpc32xx_ecc_enable;
+	nand_chip->ecc.read_page_raw = lpc32xx_read_page;
+	nand_chip->ecc.read_page = lpc32xx_read_page;
+	nand_chip->ecc.write_page_raw = lpc32xx_write_page_lowlevel;
+	nand_chip->ecc.write_page = lpc32xx_write_page_lowlevel;
+	nand_chip->ecc.write_oob = lpc32xx_write_oob;
+	nand_chip->ecc.read_oob = lpc32xx_read_oob;
+	nand_chip->ecc.strength = 4;
+	nand_chip->write_page = lpc32xx_write_page;
+	nand_chip->waitfunc = lpc32xx_waitfunc;
+
+	nand_chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB;
+	nand_chip->bbt_td = &lpc32xx_nand_bbt;
+	nand_chip->bbt_md = &lpc32xx_nand_bbt_mirror;
+
+	/* bitflip_threshold's default is defined as ecc_strength anyway.
+	 * Unfortunately, it is set only later at add_mtd_device(). Meanwhile
+	 * being 0, it causes bad block table scanning errors in
+	 * nand_scan_tail(), so preparing it here. */
+	mtd->bitflip_threshold = nand_chip->ecc.strength;
+
+	host->dma_buf = devm_kzalloc(&pdev->dev, NAND_LARGE_BLOCK_PAGE_SIZE,
+				     GFP_KERNEL);
+	if (!host->dma_buf) {
+		dev_err(&pdev->dev, "Error allocating memory\n");
+		res = -ENOMEM;
+		goto err_exit2;
+	}
+
+	res = lpc32xx_dma_setup(host);
+	if (res) {
+		res = -EIO;
+		goto err_exit2;
+	}
+
+	/*
+	 * Scan to find existance of the device and
+	 * Get the type of NAND device SMALL block or LARGE block
+	 */
+	if (nand_scan_ident(mtd, 1, NULL)) {
+		res = -ENXIO;
+		goto err_exit3;
+	}
+
+	nand_chip->ecc.mode = NAND_ECC_HW;
+	nand_chip->ecc.size = mtd->writesize;
+	nand_chip->ecc.layout = &lpc32xx_nand_oob;
+
+	/* initially clear interrupt status */
+	sr = readb(MLC_IRQ_SR(host->io_base));
+
+	init_completion(&host->comp_nand);
+	init_completion(&host->comp_controller);
+
+	host->irq = platform_get_irq(pdev, 0);
+	if ((host->irq < 0) || (host->irq >= NR_IRQS)) {
+		dev_err(&pdev->dev, "failed to get platform irq\n");
+		res = -EINVAL;
+		goto err_exit3;
+	}
+
+	if (request_irq(host->irq, (irq_handler_t)&lpc3xxx_nand_irq,
+			IRQF_TRIGGER_HIGH, DRV_NAME, host)) {
+		dev_err(&pdev->dev, "Error requesting NAND IRQ\n");
+		res = -ENXIO;
+		goto err_exit3;
+	}
+
+	/*
+	 * Fills out all the uninitialized function pointers with the defaults
+	 * And scans for a bad block table if appropriate.
+	 */
+	if (nand_scan_tail(mtd)) {
+		res = -ENXIO;
+		goto err_exit4;
+	}
+
+	mtd->name = DRV_NAME;
+
+	ppdata.of_node = pdev->dev.of_node;
+	res = mtd_device_parse_register(mtd, NULL, &ppdata, host->ncfg->parts,
+					host->ncfg->num_parts);
+	if (!res)
+		return res;
+
+	nand_release(mtd);
+
+err_exit4:
+	free_irq(host->irq, host);
+err_exit3:
+	dma_release_channel(host->dma_chan);
+err_exit2:
+	clk_disable(host->clk);
+	clk_put(host->clk);
+	platform_set_drvdata(pdev, NULL);
+err_exit1:
+	lpc32xx_wp_enable(host);
+	gpio_free(host->ncfg->wp_gpio);
+
+	return res;
+}
+
+/*
+ * Remove NAND device
+ */
+static int __devexit lpc32xx_nand_remove(struct platform_device *pdev)
+{
+	struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
+	struct mtd_info *mtd = &host->mtd;
+
+	nand_release(mtd);
+	free_irq(host->irq, host);
+	dma_release_channel(host->dma_chan);
+
+	clk_disable(host->clk);
+	clk_put(host->clk);
+	platform_set_drvdata(pdev, NULL);
+
+	lpc32xx_wp_enable(host);
+	gpio_free(host->ncfg->wp_gpio);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int lpc32xx_nand_resume(struct platform_device *pdev)
+{
+	struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
+
+	/* Re-enable NAND clock */
+	clk_enable(host->clk);
+
+	/* Fresh init of NAND controller */
+	lpc32xx_nand_setup(host);
+
+	/* Disable write protect */
+	lpc32xx_wp_disable(host);
+
+	return 0;
+}
+
+static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm)
+{
+	struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
+
+	/* Enable write protect for safety */
+	lpc32xx_wp_enable(host);
+
+	/* Disable clock */
+	clk_disable(host->clk);
+	return 0;
+}
+
+#else
+#define lpc32xx_nand_resume NULL
+#define lpc32xx_nand_suspend NULL
+#endif
+
+#if defined(CONFIG_OF)
+static const struct of_device_id lpc32xx_nand_match[] = {
+	{ .compatible = "nxp,lpc3220-mlc" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, lpc32xx_nand_match);
+#endif
+
+static struct platform_driver lpc32xx_nand_driver = {
+	.probe		= lpc32xx_nand_probe,
+	.remove		= __devexit_p(lpc32xx_nand_remove),
+	.resume		= lpc32xx_nand_resume,
+	.suspend	= lpc32xx_nand_suspend,
+	.driver		= {
+		.name	= DRV_NAME,
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(lpc32xx_nand_match),
+	},
+};
+
+module_platform_driver(lpc32xx_nand_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Roland Stigge <stigge-uj/7R2tJ6VmzQB+pC5nmwQ@public.gmane.org>");
+MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX MLC controller");

Re: [PATCH v5] MTD: LPC32xx SLC NAND driver

[Artem Bityutskiy]

[-- Attachment #1: Type: text/plain, Size: 310 bytes --]

On Mon, 2012-06-04 at 21:25 +0200, Roland Stigge wrote:
> +config MTD_NAND_SLC_LPC32XX
> +	bool "NXP LPC32xx SLC Controller"

Why bool and not tristate here? Why you force this to be compiled-in and
make it impossible to be a kernel module like other drivers are?

-- 
Best Regards,
Artem Bityutskiy

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH v5] MTD: LPC32xx SLC NAND driver

[Roland Stigge]

On 06/06/2012 10:42 AM, Artem Bityutskiy wrote:
> On Mon, 2012-06-04 at 21:25 +0200, Roland Stigge wrote:
>> +config MTD_NAND_SLC_LPC32XX +	bool "NXP LPC32xx SLC Controller"
> 
> Why bool and not tristate here? Why you force this to be
> compiled-in and make it impossible to be a kernel module like other
> drivers are?

Right - the solution for both issues you mention (compiling as module
and linker error) is replacing above "bool" with "tristate".

Will post an updated patch.

Thanks,

Roland

Re: [PATCH v5] MTD: LPC32xx SLC NAND driver

[Artem Bityutskiy]

[-- Attachment #1.1: Type: text/plain, Size: 1049 bytes --]

On Mon, 2012-06-04 at 21:25 +0200, Roland Stigge wrote:
> This patch adds support for the SLC NAND controller inside the LPC32xx
> SoC.
> 
> Signed-off-by: Roland Stigge <stigge@antcom.de>
> 
This patch does not build:

$ make ARCH=arm CROSS_COMPILE=arm-unknown-linux-gnueabi- -j20
...
drivers/built-in.o: In function `lpc32xx_nand_probe':
/home/dedekind/git/l2-mtd/drivers/mtd/nand/lpc32xx_nand_slc.c:894: undefined reference to `nand_scan_ident'
/home/dedekind/git/l2-mtd/drivers/mtd/nand/lpc32xx_nand_slc.c:934: undefined reference to `nand_scan_tail'
/home/dedekind/git/l2-mtd/drivers/mtd/nand/lpc32xx_nand_slc.c:941: undefined reference to `nand_default_bbt'
/home/dedekind/git/l2-mtd/drivers/mtd/nand/lpc32xx_nand_slc.c:953: undefined reference to `nand_release'
drivers/built-in.o: In function `lpc32xx_nand_remove':
/home/dedekind/git/l2-mtd/drivers/mtd/nand/lpc32xx_nand_slc.c:977: undefined reference to `nand_release'
make: *** [vmlinux] Error 1

with the attache .config file.

-- 
Best Regards,
Artem Bityutskiy

[-- Attachment #1.2: .config --]
[-- Type: text/plain, Size: 57931 bytes --]

#
# Automatically generated file; DO NOT EDIT.
# Linux/arm 3.5.0-rc1 Kernel Configuration
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_HAVE_PROC_CPU=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_ARM_PATCH_PHYS_VIRT=y
CONFIG_GENERIC_BUG=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_HAVE_IRQ_WORK=y

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_LZMA is not set
# CONFIG_KERNEL_XZ is not set
# CONFIG_KERNEL_LZO is not set
CONFIG_DEFAULT_HOSTNAME="(none)"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_FHANDLE is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
CONFIG_HAVE_GENERIC_HARDIRQS=y

#
# IRQ subsystem
#
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_IRQ_DOMAIN=y
CONFIG_KTIME_SCALAR=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y

#
# Timers subsystem
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y

#
# RCU Subsystem
#
CONFIG_TINY_PREEMPT_RCU=y
CONFIG_PREEMPT_RCU=y
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_RCU_BOOST is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_CGROUPS is not set
# CONFIG_CHECKPOINT_RESTORE is not set
# CONFIG_NAMESPACES is not set
# CONFIG_SCHED_AUTOGROUP is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
# CONFIG_RD_XZ is not set
# CONFIG_RD_LZO is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_EXPERT=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_EMBEDDED=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_PERF_USE_VMALLOC=y

#
# Kernel Performance Events And Counters
#
# CONFIG_PERF_EVENTS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_JUMP_LABEL=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y

#
# GCOV-based kernel profiling
#
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_BSGLIB is not set
# CONFIG_BLK_DEV_INTEGRITY is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
# CONFIG_INLINE_SPIN_TRYLOCK is not set
# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK is not set
# CONFIG_INLINE_SPIN_LOCK_BH is not set
# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
CONFIG_UNINLINE_SPIN_UNLOCK=y
# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
# CONFIG_INLINE_SPIN_UNLOCK_IRQ is not set
# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_READ_TRYLOCK is not set
# CONFIG_INLINE_READ_LOCK is not set
# CONFIG_INLINE_READ_LOCK_BH is not set
# CONFIG_INLINE_READ_LOCK_IRQ is not set
# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
# CONFIG_INLINE_READ_UNLOCK is not set
# CONFIG_INLINE_READ_UNLOCK_BH is not set
# CONFIG_INLINE_READ_UNLOCK_IRQ is not set
# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
# CONFIG_INLINE_WRITE_TRYLOCK is not set
# CONFIG_INLINE_WRITE_LOCK is not set
# CONFIG_INLINE_WRITE_LOCK_BH is not set
# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
# CONFIG_INLINE_WRITE_UNLOCK is not set
# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
# CONFIG_INLINE_WRITE_UNLOCK_IRQ is not set
# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
# CONFIG_MUTEX_SPIN_ON_OWNER is not set
CONFIG_FREEZER=y

#
# System Type
#
CONFIG_MMU=y
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_VEXPRESS is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_BCMRING is not set
# CONFIG_ARCH_HIGHBANK is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_CNS3XXX is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_PRIMA2 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_MXS is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
CONFIG_ARCH_LPC32XX=y
# CONFIG_ARCH_MV78XX0 is not set
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_TEGRA is not set
# CONFIG_ARCH_PICOXCELL is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_SHMOBILE is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C24XX is not set
# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_S5P64X0 is not set
# CONFIG_ARCH_S5PC100 is not set
# CONFIG_ARCH_S5PV210 is not set
# CONFIG_ARCH_EXYNOS is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_U8500 is not set
# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_PLAT_SPEAR is not set
# CONFIG_ARCH_VT8500 is not set
# CONFIG_ARCH_ZYNQ is not set
# CONFIG_GPIO_PCA953X is not set
# CONFIG_KEYBOARD_GPIO_POLLED is not set

#
# Individual UART enable selections
#
# CONFIG_ARCH_LPC32XX_UART3_SELECT is not set
# CONFIG_ARCH_LPC32XX_UART4_SELECT is not set
CONFIG_ARCH_LPC32XX_UART5_SELECT=y
# CONFIG_ARCH_LPC32XX_UART6_SELECT is not set

#
# Processor Type
#
CONFIG_CPU_ARM926T=y
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5TJ=y
CONFIG_CPU_PABRT_LEGACY=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
CONFIG_CPU_USE_DOMAINS=y

#
# Processor Features
#
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ARM_THUMB=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
# CONFIG_CACHE_L2X0 is not set
CONFIG_ARM_L1_CACHE_SHIFT=5
CONFIG_ARM_NR_BANKS=8

#
# Bus support
#
CONFIG_ARM_AMBA=y
# CONFIG_PCI_SYSCALL is not set
# CONFIG_ARCH_SUPPORTS_MSI is not set
# CONFIG_PCCARD is not set

#
# Kernel Features
#
CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_ARCH_NR_GPIO=0
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_COUNT=y
CONFIG_HZ=100
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
CONFIG_HAVE_ARCH_PFN_VALID=y
# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=999999
# CONFIG_COMPACTION is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_CROSS_MEMORY_ATTACH=y
CONFIG_NEED_PER_CPU_KM=y
# CONFIG_CLEANCACHE is not set
CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_ALIGNMENT_TRAP=y
# CONFIG_UACCESS_WITH_MEMCPY is not set
# CONFIG_SECCOMP is not set
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_DEPRECATED_PARAM_STRUCT is not set

#
# Boot options
#
CONFIG_USE_OF=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_CMDLINE="console=ttyS0,115200n81 root=/dev/ram0"
CONFIG_CMDLINE_FROM_BOOTLOADER=y
# CONFIG_CMDLINE_EXTEND is not set
# CONFIG_CMDLINE_FORCE is not set
# CONFIG_XIP_KERNEL is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
# CONFIG_AUTO_ZRELADDR is not set

#
# CPU Power Management
#
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y

#
# Floating point emulation
#

#
# At least one emulation must be selected
#
CONFIG_FPE_NWFPE=y
# CONFIG_FPE_NWFPE_XP is not set
# CONFIG_FPE_FASTFPE is not set
CONFIG_VFP=y

#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_HAVE_AOUT=y
CONFIG_BINFMT_AOUT=y
# CONFIG_BINFMT_MISC is not set

#
# Power management options
#
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_PM_SLEEP=y
# CONFIG_PM_AUTOSLEEP is not set
# CONFIG_PM_WAKELOCKS is not set
# CONFIG_PM_RUNTIME is not set
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
# CONFIG_APM_EMULATION is not set
CONFIG_PM_CLK=y
CONFIG_CPU_PM=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARM_CPU_SUSPEND=y
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
CONFIG_UNIX=y
# CONFIG_UNIX_DIAG is not set
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE_DEMUX is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
CONFIG_INET_TUNNEL=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=y
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
CONFIG_INET6_XFRM_MODE_TRANSPORT=y
CONFIG_INET6_XFRM_MODE_TUNNEL=y
CONFIG_INET6_XFRM_MODE_BEET=y
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=y
# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_IPV6_MROUTE is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_L2TP is not set
# CONFIG_BRIDGE is not set
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
# CONFIG_BATMAN_ADV is not set
# CONFIG_OPENVSWITCH is not set
CONFIG_BQL=y
# CONFIG_BPF_JIT is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
# CONFIG_WIRELESS is not set
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CAIF is not set
# CONFIG_CEPH_LIB is not set
# CONFIG_NFC is not set
CONFIG_HAVE_BPF_JIT=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_GENERIC_CPU_DEVICES is not set
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=y
CONFIG_REGMAP_SPI=y
# CONFIG_DMA_SHARED_BUFFER is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
CONFIG_MTD_TESTS=m
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=10000
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_AFS_PARTS=m
CONFIG_MTD_OF_PARTS=y
CONFIG_MTD_AR7_PARTS=y

#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_HAVE_MTD_OTP=y
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
CONFIG_FTL=y
CONFIG_NFTL=y
CONFIG_NFTL_RW=y
CONFIG_INFTL=y
CONFIG_RFD_FTL=y
CONFIG_SSFDC=y
CONFIG_SM_FTL=y
CONFIG_MTD_OOPS=y
CONFIG_MTD_SWAP=y

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m

#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
CONFIG_MTD_PHYSMAP_COMPAT=y
CONFIG_MTD_PHYSMAP_START=0x8000000
CONFIG_MTD_PHYSMAP_LEN=0
CONFIG_MTD_PHYSMAP_BANKWIDTH=2
CONFIG_MTD_PHYSMAP_OF=m
CONFIG_MTD_IMPA7=m
CONFIG_MTD_GPIO_ADDR=m
CONFIG_MTD_PLATRAM=m
CONFIG_MTD_LATCH_ADDR=m

#
# Self-contained MTD device drivers
#
CONFIG_MTD_DATAFLASH=m
CONFIG_MTD_DATAFLASH_WRITE_VERIFY=y
CONFIG_MTD_DATAFLASH_OTP=y
CONFIG_MTD_M25P80=m
# CONFIG_M25PXX_USE_FAST_READ is not set
CONFIG_MTD_SST25L=m
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLOCK2MTD=m

#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_DOC2000=m
CONFIG_MTD_DOC2001=m
CONFIG_MTD_DOC2001PLUS=m
CONFIG_MTD_DOCG3=m
CONFIG_BCH_CONST_M=14
CONFIG_BCH_CONST_T=4
CONFIG_MTD_DOCPROBE=m
CONFIG_MTD_DOCECC=m
CONFIG_MTD_DOCPROBE_ADVANCED=y
CONFIG_MTD_DOCPROBE_ADDRESS=0x0
# CONFIG_MTD_DOCPROBE_HIGH is not set
# CONFIG_MTD_DOCPROBE_55AA is not set
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_ECC_SMC=y
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_BCH is not set
# CONFIG_MTD_SM_COMMON is not set
CONFIG_MTD_NAND_MUSEUM_IDS=y
CONFIG_MTD_NAND_GPIO=m
CONFIG_MTD_NAND_IDS=m
CONFIG_MTD_NAND_DISKONCHIP=m
CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED=y
CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
# CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH is not set
CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
CONFIG_MTD_NAND_DOCG4=m
CONFIG_MTD_NAND_SLC_LPC32XX=y
CONFIG_MTD_NAND_NANDSIM=m
CONFIG_MTD_NAND_PLATFORM=m
CONFIG_MTD_ALAUDA=m
CONFIG_MTD_ONENAND=m
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
CONFIG_MTD_ONENAND_GENERIC=m
CONFIG_MTD_ONENAND_OTP=y
CONFIG_MTD_ONENAND_2X_PROGRAM=y
CONFIG_MTD_ONENAND_SIM=m

#
# LPDDR flash memory drivers
#
CONFIG_MTD_LPDDR=y
CONFIG_MTD_QINFO_PROBE=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_RESERVE=1
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_DTC=y
CONFIG_OF=y

#
# Device Tree and Open Firmware support
#
# CONFIG_PROC_DEVICETREE is not set
# CONFIG_OF_SELFTEST is not set
CONFIG_OF_FLATTREE=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_IRQ=y
CONFIG_OF_DEVICE=y
CONFIG_OF_I2C=y
CONFIG_OF_NET=y
CONFIG_OF_MDIO=y
CONFIG_OF_MTD=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
CONFIG_BLK_DEV_CRYPTOLOOP=y

#
# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
#
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=1
CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MG_DISK is not set
# CONFIG_BLK_DEV_RBD is not set

#
# Misc devices
#
# CONFIG_SENSORS_LIS3LV02D is not set
# CONFIG_AD525X_DPOT is not set
# CONFIG_ATMEL_PWM is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_APDS9802ALS is not set
# CONFIG_ISL29003 is not set
# CONFIG_ISL29020 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1780 is not set
# CONFIG_SENSORS_BH1770 is not set
# CONFIG_SENSORS_APDS990X is not set
# CONFIG_HMC6352 is not set
# CONFIG_DS1682 is not set
# CONFIG_TI_DAC7512 is not set
# CONFIG_BMP085_I2C is not set
# CONFIG_BMP085_SPI is not set
# CONFIG_USB_SWITCH_FSA9480 is not set
# CONFIG_C2PORT is not set

#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
CONFIG_EEPROM_AT25=y
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_EEPROM_93XX46 is not set
# CONFIG_IWMC3200TOP is not set

#
# Texas Instruments shared transport line discipline
#
# CONFIG_TI_ST is not set
# CONFIG_SENSORS_LIS3_SPI is not set
# CONFIG_SENSORS_LIS3_I2C is not set

#
# Altera FPGA firmware download module
#
# CONFIG_ALTERA_STAPL is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_ISCSI_BOOT_SYSFS is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
# CONFIG_TARGET_CORE is not set
CONFIG_NETDEVICES=y
CONFIG_NET_CORE=y
# CONFIG_BONDING is not set
# CONFIG_DUMMY is not set
# CONFIG_EQUALIZER is not set
CONFIG_MII=y
# CONFIG_NET_TEAM is not set
# CONFIG_MACVLAN is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set

#
# CAIF transport drivers
#
CONFIG_ETHERNET=y
# CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_CALXEDA_XGMAC is not set
# CONFIG_NET_VENDOR_CHELSIO is not set
# CONFIG_NET_VENDOR_CIRRUS is not set
# CONFIG_DM9000 is not set
# CONFIG_DNET is not set
# CONFIG_NET_VENDOR_FARADAY is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set
# CONFIG_NET_VENDOR_MICREL is not set
# CONFIG_NET_VENDOR_MICROCHIP is not set
# CONFIG_NET_VENDOR_NATSEMI is not set
CONFIG_LPC_ENET=y
# CONFIG_ETHOC is not set
# CONFIG_NET_VENDOR_SEEQ is not set
# CONFIG_NET_VENDOR_SMSC is not set
# CONFIG_NET_VENDOR_STMICRO is not set
CONFIG_NET_VENDOR_WIZNET=y
# CONFIG_WIZNET_W5100 is not set
# CONFIG_WIZNET_W5300 is not set
CONFIG_PHYLIB=y

#
# MII PHY device drivers
#
# CONFIG_AMD_PHY is not set
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
CONFIG_SMSC_PHY=y
# CONFIG_BROADCOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
# CONFIG_REALTEK_PHY is not set
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_FIXED_PHY is not set
# CONFIG_MDIO_BITBANG is not set
# CONFIG_MDIO_BUS_MUX_GPIO is not set
# CONFIG_MICREL_KS8995MA is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_WLAN is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#
# CONFIG_WAN is not set
# CONFIG_ISDN is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
# CONFIG_INPUT_SPARSEKMAP is not set
# CONFIG_INPUT_MATRIXKMAP is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=240
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ADP5589 is not set
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_QT1070 is not set
# CONFIG_KEYBOARD_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_GPIO is not set
# CONFIG_KEYBOARD_TCA6416 is not set
# CONFIG_KEYBOARD_TCA8418 is not set
# CONFIG_KEYBOARD_MATRIX is not set
# CONFIG_KEYBOARD_LM8323 is not set
# CONFIG_KEYBOARD_LM8333 is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_MCS is not set
# CONFIG_KEYBOARD_MPR121 is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_SAMSUNG is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_OMAP4 is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_ADS7846 is not set
# CONFIG_TOUCHSCREEN_AD7877 is not set
# CONFIG_TOUCHSCREEN_AD7879 is not set
# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
# CONFIG_TOUCHSCREEN_AUO_PIXCIR is not set
# CONFIG_TOUCHSCREEN_BU21013 is not set
# CONFIG_TOUCHSCREEN_CY8CTMG110 is not set
# CONFIG_TOUCHSCREEN_CYTTSP_CORE is not set
# CONFIG_TOUCHSCREEN_DYNAPRO is not set
# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_EGALAX is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_ILI210X is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
# CONFIG_TOUCHSCREEN_WACOM_I2C is not set
CONFIG_TOUCHSCREEN_LPC32XX=y
# CONFIG_TOUCHSCREEN_MAX11801 is not set
# CONFIG_TOUCHSCREEN_MCS5000 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
# CONFIG_TOUCHSCREEN_PENMOUNT is not set
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_PIXCIR is not set
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
# CONFIG_TOUCHSCREEN_TSC2005 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
# CONFIG_TOUCHSCREEN_W90X900 is not set
# CONFIG_TOUCHSCREEN_ST1232 is not set
# CONFIG_TOUCHSCREEN_TPS6507X is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_AMBAKMI is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_SERIO_PS2MULT is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_VT_CONSOLE_SLEEP=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_N_GSM is not set
# CONFIG_TRACE_SINK is not set
CONFIG_DEVKMEM=y

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
# CONFIG_SERIAL_8250_DW is not set
# CONFIG_SERIAL_8250_EM is not set

#
# Non-8250 serial port support
#
# CONFIG_SERIAL_AMBA_PL010 is not set
# CONFIG_SERIAL_AMBA_PL011 is not set
# CONFIG_SERIAL_MAX3100 is not set
# CONFIG_SERIAL_MAX3107 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_OF_PLATFORM is not set
# CONFIG_SERIAL_TIMBERDALE is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_IFX6X60 is not set
# CONFIG_SERIAL_XILINX_PS_UART is not set
# CONFIG_TTY_PRINTK is not set
# CONFIG_HVC_DCC is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
# CONFIG_I2C_MUX is not set
CONFIG_I2C_HELPER_AUTO=y

#
# I2C Hardware Bus support
#

#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_DESIGNWARE_PLATFORM is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PCA_PLATFORM is not set
CONFIG_I2C_PNX=y
# CONFIG_I2C_PXA_PCI is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_DIOLAN_U2C is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_TINY_USB is not set

#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
CONFIG_SPI=y
# CONFIG_SPI_DEBUG is not set
CONFIG_SPI_MASTER=y

#
# SPI Master Controller Drivers
#
# CONFIG_SPI_ALTERA is not set
# CONFIG_SPI_BITBANG is not set
# CONFIG_SPI_GPIO is not set
# CONFIG_SPI_OC_TINY is not set
CONFIG_SPI_PL022=y
# CONFIG_SPI_PXA2XX_PCI is not set
# CONFIG_SPI_XILINX is not set
# CONFIG_SPI_DESIGNWARE is not set

#
# SPI Protocol Masters
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
# CONFIG_HSI is not set

#
# PPS support
#
# CONFIG_PPS is not set

#
# PPS generators support
#

#
# PTP clock support
#

#
# Enable Device Drivers -> PPS to see the PTP clock options.
#
CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
CONFIG_OF_GPIO=y
# CONFIG_DEBUG_GPIO is not set
CONFIG_GPIO_SYSFS=y

#
# Memory mapped GPIO drivers:
#
# CONFIG_GPIO_GENERIC_PLATFORM is not set
# CONFIG_GPIO_EM is not set
# CONFIG_GPIO_PL061 is not set

#
# I2C GPIO expanders:
#
# CONFIG_GPIO_MAX7300 is not set
# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCF857X is not set
# CONFIG_GPIO_SX150X is not set
# CONFIG_GPIO_ADP5588 is not set

#
# PCI GPIO expanders:
#

#
# SPI GPIO expanders:
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
# CONFIG_GPIO_MC33880 is not set
# CONFIG_GPIO_74X164 is not set

#
# AC97 GPIO expanders:
#

#
# MODULbus GPIO expanders:
#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_CORE=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_ARM_SP805_WATCHDOG is not set
# CONFIG_DW_WATCHDOG is not set
CONFIG_PNX4008_WATCHDOG=y
# CONFIG_MAX63XX_WATCHDOG is not set

#
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
CONFIG_BCMA_POSSIBLE=y

#
# Broadcom specific AMBA
#
# CONFIG_BCMA is not set

#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_HTC_I2CPLD is not set
# CONFIG_MFD_LM3533 is not set
# CONFIG_TPS6105X is not set
# CONFIG_TPS65010 is not set
# CONFIG_TPS6507X is not set
# CONFIG_MFD_TPS65217 is not set
# CONFIG_MFD_TPS65910 is not set
# CONFIG_MFD_TPS65912_I2C is not set
# CONFIG_MFD_TPS65912_SPI is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_TWL6040_CORE is not set
# CONFIG_MFD_STMPE is not set
# CONFIG_MFD_TC3589X is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_DA9052_SPI is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_MAX77693 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_MAX8997 is not set
# CONFIG_MFD_MAX8998 is not set
# CONFIG_MFD_S5M_CORE is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM831X_SPI is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_MC13XXX_SPI is not set
# CONFIG_MFD_MC13XXX_I2C is not set
# CONFIG_ABX500_CORE is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_MFD_WL1273_CORE is not set
# CONFIG_MFD_TPS65090 is not set
# CONFIG_MFD_AAT2870_CORE is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_PALMAS is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
# CONFIG_FB_BOOT_VESA_SUPPORT is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_WMT_GE_ROPS is not set
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set

#
# Frame buffer hardware drivers
#
CONFIG_FB_ARMCLCD=y
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_SMSCUFX is not set
# CONFIG_FB_UDL is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_BROADSHEET is not set
# CONFIG_FB_AUO_K190X is not set
# CONFIG_EXYNOS_VIDEO is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
CONFIG_SOUND_OSS_CORE_PRECLAIM=y
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_JACK=y
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_HRTIMER is not set
# CONFIG_SND_DYNAMIC_MINORS is not set
# CONFIG_SND_SUPPORT_OLD_API is not set
# CONFIG_SND_VERBOSE_PROCFS is not set
# CONFIG_SND_VERBOSE_PRINTK is not set
CONFIG_SND_DEBUG=y
CONFIG_SND_DEBUG_VERBOSE=y
# CONFIG_SND_RAWMIDI_SEQ is not set
# CONFIG_SND_OPL3_LIB_SEQ is not set
# CONFIG_SND_OPL4_LIB_SEQ is not set
# CONFIG_SND_SBAWE_SEQ is not set
# CONFIG_SND_EMU10K1_SEQ is not set
# CONFIG_SND_DRIVERS is not set
# CONFIG_SND_ARM is not set
# CONFIG_SND_SPI is not set
CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_UA101 is not set
# CONFIG_SND_USB_CAIAQ is not set
# CONFIG_SND_USB_6FIRE is not set
CONFIG_SND_SOC=y
CONFIG_SND_SOC_I2C_AND_SPI=y
# CONFIG_SND_SOC_ALL_CODECS is not set
# CONFIG_SND_SIMPLE_CARD is not set
# CONFIG_SOUND_PRIME is not set
# CONFIG_HID_SUPPORT is not set
CONFIG_USB_ARCH_HAS_OHCI=y
# CONFIG_USB_ARCH_HAS_EHCI is not set
# CONFIG_USB_ARCH_HAS_XHCI is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

#
# Miscellaneous USB options
#
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
# CONFIG_USB_DWC3 is not set
# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB_CBAF is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_HCD_PLATFORM is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_MUSB_HDRC is not set
# CONFIG_USB_CHIPIDEA is not set
# CONFIG_USB_RENESAS_USBHS is not set

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_WDM is not set
# CONFIG_USB_TMC is not set

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_REALTEK is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_STORAGE_ENE_UB6250 is not set
# CONFIG_USB_UAS is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB port drivers
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_YUREX is not set

#
# USB Physical Layer drivers
#
CONFIG_USB_ISP1301=y
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG is not set
# CONFIG_USB_GADGET_DEBUG_FILES is not set
CONFIG_USB_GADGET_VBUS_DRAW=2
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2

#
# USB Peripheral Controller
#
CONFIG_USB_LPC32XX=y
# CONFIG_USB_FUSB300 is not set
# CONFIG_USB_R8A66597 is not set
# CONFIG_USB_MV_UDC is not set
# CONFIG_USB_M66592 is not set
# CONFIG_USB_NET2272 is not set
# CONFIG_USB_DUMMY_HCD is not set
# CONFIG_USB_ZERO is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_ETH is not set
# CONFIG_USB_G_NCM is not set
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FUNCTIONFS is not set
# CONFIG_USB_FILE_STORAGE is not set
CONFIG_USB_MASS_STORAGE=m
CONFIG_USB_G_SERIAL=m
# CONFIG_USB_MIDI_GADGET is not set
# CONFIG_USB_G_PRINTER is not set
# CONFIG_USB_CDC_COMPOSITE is not set
# CONFIG_USB_G_ACM_MS is not set
# CONFIG_USB_G_MULTI is not set
# CONFIG_USB_G_HID is not set
# CONFIG_USB_G_DBGP is not set

#
# OTG and related infrastructure
#
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_USB_ULPI is not set
# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
# CONFIG_MMC_CLKGATE is not set

#
# MMC/SD/SDIO Card Drivers
#
CONFIG_MMC_BLOCK=y
CONFIG_MMC_BLOCK_MINORS=8
# CONFIG_MMC_BLOCK_BOUNCE is not set
# CONFIG_SDIO_UART is not set
# CONFIG_MMC_TEST is not set

#
# MMC/SD/SDIO Host Controller Drivers
#
CONFIG_MMC_ARMMMCI=y
# CONFIG_MMC_SDHCI is not set
# CONFIG_MMC_SDHCI_PXAV3 is not set
# CONFIG_MMC_SDHCI_PXAV2 is not set
# CONFIG_MMC_SPI is not set
# CONFIG_MMC_DW is not set
# CONFIG_MMC_VUB300 is not set
# CONFIG_MMC_USHC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#
# CONFIG_LEDS_LM3530 is not set
# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_LP5521 is not set
# CONFIG_LEDS_LP5523 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_PCA9633 is not set
# CONFIG_LEDS_DAC124S085 is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_LEDS_LT3593 is not set
# CONFIG_LEDS_RENESAS_TPU is not set
# CONFIG_LEDS_TCA6507 is not set
# CONFIG_LEDS_OT200 is not set
CONFIG_LEDS_TRIGGERS=y

#
# LED Triggers
#
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_BACKLIGHT=y
CONFIG_LEDS_TRIGGER_GPIO=y
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y

#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_LEDS_TRIGGER_TRANSIENT is not set
# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
# CONFIG_RTC_DRV_TEST is not set

#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
CONFIG_RTC_DRV_DS1374=y
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_DS3232 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_ISL12022 is not set
# CONFIG_RTC_DRV_X1205 is not set
CONFIG_RTC_DRV_PCF8563=y
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_BQ32K is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set
# CONFIG_RTC_DRV_EM3027 is not set
# CONFIG_RTC_DRV_RV3029C2 is not set

#
# SPI RTC drivers
#
# CONFIG_RTC_DRV_M41T93 is not set
# CONFIG_RTC_DRV_M41T94 is not set
# CONFIG_RTC_DRV_DS1305 is not set
# CONFIG_RTC_DRV_DS1390 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
# CONFIG_RTC_DRV_PCF2123 is not set

#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set

#
# on-CPU RTC drivers
#
# CONFIG_RTC_DRV_PL030 is not set
# CONFIG_RTC_DRV_PL031 is not set
CONFIG_RTC_DRV_LPC32XX=y
CONFIG_DMADEVICES=y
# CONFIG_DMADEVICES_DEBUG is not set

#
# DMA Devices
#
CONFIG_AMBA_PL08X=y
# CONFIG_DW_DMAC is not set
# CONFIG_TIMB_DMA is not set
# CONFIG_PL330_DMA is not set
CONFIG_DMA_ENGINE=y

#
# DMA Clients
#
# CONFIG_NET_DMA is not set
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set

#
# Virtio drivers
#
# CONFIG_VIRTIO_BALLOON is not set
# CONFIG_VIRTIO_MMIO is not set

#
# Microsoft Hyper-V guest support
#
CONFIG_STAGING=y
# CONFIG_USBIP_CORE is not set
# CONFIG_ECHO is not set
# CONFIG_ASUS_OLED is not set
# CONFIG_RTS5139 is not set
# CONFIG_TRANZPORT is not set
# CONFIG_LINE6_USB is not set

#
# IIO staging drivers
#

#
# Accelerometers
#
# CONFIG_ADIS16201 is not set
# CONFIG_ADIS16203 is not set
# CONFIG_ADIS16204 is not set
# CONFIG_ADIS16209 is not set
# CONFIG_ADIS16220 is not set
# CONFIG_ADIS16240 is not set
# CONFIG_KXSD9 is not set
# CONFIG_LIS3L02DQ is not set

#
# Analog to digital converters
#
# CONFIG_AD7291 is not set
# CONFIG_AD7298 is not set
# CONFIG_AD7606 is not set
# CONFIG_AD799X is not set
# CONFIG_AD7476 is not set
# CONFIG_AD7887 is not set
# CONFIG_AD7780 is not set
# CONFIG_AD7793 is not set
# CONFIG_AD7816 is not set
# CONFIG_AD7192 is not set
# CONFIG_ADT7310 is not set
# CONFIG_ADT7410 is not set
# CONFIG_AD7280 is not set
# CONFIG_MAX1363 is not set
CONFIG_LPC32XX_ADC=y

#
# Analog digital bi-direction converters
#
# CONFIG_ADT7316 is not set

#
# Capacitance to digital converters
#
# CONFIG_AD7150 is not set
# CONFIG_AD7152 is not set
# CONFIG_AD7746 is not set

#
# Digital to analog converters
#
# CONFIG_AD5064 is not set
# CONFIG_AD5360 is not set
# CONFIG_AD5380 is not set
# CONFIG_AD5421 is not set
# CONFIG_AD5624R_SPI is not set
# CONFIG_AD5446 is not set
# CONFIG_AD5504 is not set
# CONFIG_AD5764 is not set
# CONFIG_AD5791 is not set
# CONFIG_AD5686 is not set
# CONFIG_MAX517 is not set

#
# Direct Digital Synthesis
#
# CONFIG_AD5930 is not set
# CONFIG_AD9832 is not set
# CONFIG_AD9834 is not set
# CONFIG_AD9850 is not set
# CONFIG_AD9852 is not set
# CONFIG_AD9910 is not set
# CONFIG_AD9951 is not set

#
# Digital gyroscope sensors
#
# CONFIG_ADIS16060 is not set
# CONFIG_ADIS16080 is not set
# CONFIG_ADIS16130 is not set
# CONFIG_ADIS16260 is not set
# CONFIG_ADXRS450 is not set

#
# Network Analyzer, Impedance Converters
#
# CONFIG_AD5933 is not set

#
# Inertial measurement units
#
# CONFIG_ADIS16400 is not set

#
# Light sensors
#
# CONFIG_SENSORS_ISL29018 is not set
# CONFIG_SENSORS_ISL29028 is not set
# CONFIG_SENSORS_TSL2563 is not set
# CONFIG_TSL2583 is not set
# CONFIG_TSL2x7x is not set

#
# Magnetometer sensors
#
# CONFIG_SENSORS_AK8975 is not set
# CONFIG_SENSORS_HMC5843 is not set

#
# Active energy metering IC
#
# CONFIG_ADE7753 is not set
# CONFIG_ADE7754 is not set
# CONFIG_ADE7758 is not set
# CONFIG_ADE7759 is not set
# CONFIG_ADE7854 is not set

#
# Resolver to digital converters
#
# CONFIG_AD2S90 is not set
# CONFIG_AD2S1200 is not set
# CONFIG_AD2S1210 is not set

#
# Triggers - standalone
#
# CONFIG_IIO_SIMPLE_DUMMY is not set
# CONFIG_FB_SM7XX is not set
# CONFIG_USB_ENESTORAGE is not set
# CONFIG_BCM_WIMAX is not set
# CONFIG_FT1000 is not set

#
# Speakup console speech
#
# CONFIG_SPEAKUP is not set
# CONFIG_TOUCHSCREEN_CLEARPAD_TM1217 is not set
# CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4 is not set
# CONFIG_STAGING_MEDIA is not set

#
# Android
#
# CONFIG_ANDROID is not set
# CONFIG_PHONE is not set
# CONFIG_USB_WPAN_HCD is not set
# CONFIG_USB_G_CCG is not set
# CONFIG_IPACK_BUS is not set
# CONFIG_WIMAX_GDM72XX is not set
CONFIG_CLKDEV_LOOKUP=y

#
# Hardware Spinlock drivers
#
CONFIG_CLKSRC_MMIO=y
CONFIG_IOMMU_SUPPORT=y

#
# Remoteproc drivers (EXPERIMENTAL)
#

#
# Rpmsg drivers (EXPERIMENTAL)
#
# CONFIG_VIRT_DRIVERS is not set
# CONFIG_PM_DEVFREQ is not set
# CONFIG_EXTCON is not set
# CONFIG_MEMORY is not set
CONFIG_IIO=y
# CONFIG_IIO_BUFFER is not set
# CONFIG_IIO_TRIGGER is not set

#
# Analog to digital converters
#

#
# Amplifiers
#
# CONFIG_AD8366 is not set

#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
# CONFIG_EXT3_FS is not set
# CONFIG_EXT4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
# CONFIG_FS_POSIX_ACL is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FANOTIFY is not set
# CONFIG_QUOTA is not set
# CONFIG_QUOTACTL is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
CONFIG_JFFS2_FS_WBUF_VERIFY=y
# CONFIG_JFFS2_SUMMARY is not set
CONFIG_JFFS2_FS_XATTR=y
# CONFIG_JFFS2_FS_POSIX_ACL is not set
# CONFIG_JFFS2_FS_SECURITY is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_UBIFS_FS=m
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
# CONFIG_UBIFS_FS_LZO is not set
# CONFIG_UBIFS_FS_ZLIB is not set
CONFIG_LOGFS=y
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX6FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_PSTORE is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V2=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
CONFIG_ROOT_NFS=y
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_SUNRPC_DEBUG is not set
# CONFIG_CEPH_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_MAC_ROMAN is not set
# CONFIG_NLS_MAC_CELTIC is not set
# CONFIG_NLS_MAC_CENTEURO is not set
# CONFIG_NLS_MAC_CROATIAN is not set
# CONFIG_NLS_MAC_CYRILLIC is not set
# CONFIG_NLS_MAC_GAELIC is not set
# CONFIG_NLS_MAC_GREEK is not set
# CONFIG_NLS_MAC_ICELAND is not set
# CONFIG_NLS_MAC_INUIT is not set
# CONFIG_NLS_MAC_ROMANIAN is not set
# CONFIG_NLS_MAC_TURKISH is not set
CONFIG_NLS_UTF8=y

#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_SECTION_MISMATCH is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
# CONFIG_LOCKUP_DETECTOR is not set
# CONFIG_HARDLOCKUP_DETECTOR is not set
# CONFIG_DETECT_HUNG_TASK is not set
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_SPARSE_RCU_POINTER is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_INFO_REDUCED is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_WRITECOUNT is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_TEST_LIST_SORT is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_TRACE is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
# CONFIG_TEST_KSTRTOX is not set
# CONFIG_STRICT_DEVMEM is not set
# CONFIG_ARM_UNWIND is not set
# CONFIG_DEBUG_USER is not set
CONFIG_DEBUG_LL=y
CONFIG_DEBUG_LL_UART_NONE=y
# CONFIG_DEBUG_ICEDCC is not set
# CONFIG_DEBUG_SEMIHOSTING is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_OC_ETM is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP2=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_USER is not set
CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set

#
# Block modes
#
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set

#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set

#
# Ciphers
#
CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_TWOFISH is not set

#
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set

#
# Random Number Generation
#
CONFIG_CRYPTO_ANSI_CPRNG=y
# CONFIG_CRYPTO_USER_API_HASH is not set
# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
# CONFIG_CRYPTO_HW is not set
# CONFIG_BINARY_PRINTF is not set

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_IO=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=m
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not set
CONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
# CONFIG_CRC8 is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
# CONFIG_XZ_DEC is not set
# CONFIG_XZ_DEC_BCJ is not set
CONFIG_DECOMPRESS_GZIP=y
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_BCH=m
CONFIG_BCH_CONST_PARAMS=y
CONFIG_BTREE=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_DQL=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
# CONFIG_AVERAGE is not set
# CONFIG_CORDIC is not set
# CONFIG_DDR is not set

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]