Re: [PATCH 1/6] dt-bindings: usb: dwc3: Clean up hs_phy_irq in bindings

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 22/11/2023 20:13, Krishna Kurapati wrote:
> The high speed related interrupts present on QC targets are as follows:
> 
> dp/dm Irq's
> These IRQ's directly reflect changes on the DP/DM pads of the SoC. These
> are used as wakeup interrupts only on SoCs with non-QUSBb2 targets with
> exception of SDM670/SDM845/SM6350.
> 
> qusb2_phy irq
> SoCs with QUSB2 PHY do not have separate DP/DM IRQs and expose only a
> single IRQ whose behavior can be modified by the QUSB2PHY_INTR_CTRL
> register. The required DPSE/DMSE configuration is done in
> QUSB2PHY_INTR_CTRL register of phy address space.
> 
> hs_phy_irq
> This is completely different from the above two and is present on all
> targets with exception of a few IPQ ones. The interrupt is not enabled by
> default and its functionality is mutually exclusive of qusb2_phy on QUSB
> targets and DP/DM on femto phy targets.
> 
> The DTs of several QUSB2 PHY based SoCs incorrectly define "hs_phy_irq"
> when they should have been "qusb2_phy_irq". On Femto phy targets, the
> "hs_phy_irq" mentioned is either the actual "hs_phy_irq" or "pwr_event",
> neither of which would never be triggered directly are non-functional
> currently. The implementation tries to clean up this issue by addressing
> the discrepencies involved and fixing the hs_phy_irq's in respective DT's.
> 
> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
> ---
>  .../devicetree/bindings/usb/qcom,dwc3.yaml    | 125 ++++++++++--------
>  1 file changed, 69 insertions(+), 56 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> index e889158ca205..4a46346e2ead 100644
> --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> @@ -17,20 +17,25 @@ properties:
>            - qcom,ipq5018-dwc3
>            - qcom,ipq5332-dwc3
>            - qcom,ipq6018-dwc3
> +          - qcom,ipq6018-dwc3-sec

I could not understand from commit msg why you are adding new compatible
and what it is supposed to fix.

The entire diff is huge thus difficult to review. Why fixing hs_phy_irq
causes three new interrupts being added?
>            - qcom,ipq8064-dwc3
>            - qcom,ipq8074-dwc3
>            - qcom,ipq9574-dwc3
>            - qcom,msm8953-dwc3
>            - qcom,msm8994-dwc3
>            - qcom,msm8996-dwc3
> +          - qcom,msm8996-dwc3-sec
>            - qcom,msm8998-dwc3
>            - qcom,qcm2290-dwc3
>            - qcom,qcs404-dwc3
>            - qcom,sa8775p-dwc3
> +          - qcom,sa8775p-dwc3-ter

Ter?


Best regards,
Krzysztof