Re: [PATCH 4/4] phy: freescale: phy-fsl-imx8-mipi-dphy: Add i.MX8qxp LVDS PHY mode support

[Liu Ying <victor.liu@nxp.com>]

Hi Guido,

On Thu, 2020-12-10 at 08:14 +0100, Guido Günther wrote:
> Hi,
> On Tue, Dec 08, 2020 at 06:03:05PM +0800, Liu Ying wrote:
> > On Tue, 2020-12-08 at 10:24 +0100, Guido Günther wrote:
> > > Hi Liu,
> > > some minor comments inline:
> > > 
> > > On Fri, Dec 04, 2020 at 03:33:44PM +0800, Liu Ying wrote:
> > > > i.MX8qxp SoC embeds a Mixel MIPI DPHY + LVDS PHY combo which supports
> > > > either a MIPI DSI display or a LVDS display.  The PHY mode is controlled
> > > > by SCU firmware and the driver would call a SCU firmware function to
> > > > configure the PHY mode.  The single LVDS PHY has 4 data lanes to support
> > > > a LVDS display.  Also, with a master LVDS PHY and a slave LVDS PHY, they
> > > > may work together to support a LVDS display with 8 data lanes(usually, dual
> > > > LVDS link display).  Note that this patch supports the LVDS PHY mode only
> > > > for the i.MX8qxp Mixel combo PHY, i.e., the MIPI DPHY mode is yet to be
> > > > supported, so for now error would be returned from ->set_mode() if MIPI
> > > > DPHY mode is passed over to it for the combo PHY.
> > > > 
> > > > Cc: Guido Günther <agx@sigxcpu.org>
> > > > Cc: Robert Chiras <robert.chiras@nxp.com>
> > > > Cc: Kishon Vijay Abraham I <kishon@ti.com>
> > > > Cc: Vinod Koul <vkoul@kernel.org>
> > > > Cc: Shawn Guo <shawnguo@kernel.org>
> > > > Cc: Sascha Hauer <s.hauer@pengutronix.de>
> > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
> > > > Cc: Fabio Estevam <festevam@gmail.com>
> > > > Cc: NXP Linux Team <linux-imx@nxp.com>
> > > > Signed-off-by: Liu Ying <victor.liu@nxp.com>
> > > > ---
> > > >  drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c | 266 ++++++++++++++++++++++++-
> > > >  1 file changed, 255 insertions(+), 11 deletions(-)
> > > > 
> > > > diff --git a/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c b/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c
> > > > index a95572b..37084a9 100644
> > > > --- a/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c
> > > > +++ b/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c
> > > > @@ -4,17 +4,31 @@
> > > >   * Copyright 2019 Purism SPC
> > > >   */
> > > >  
> > > > +#include <linux/bitfield.h>
> > > >  #include <linux/clk.h>
> > > >  #include <linux/clk-provider.h>
> > > >  #include <linux/delay.h>
> > > > +#include <linux/firmware/imx/ipc.h>
> > > > +#include <linux/firmware/imx/svc/misc.h>
> > > >  #include <linux/io.h>
> > > >  #include <linux/kernel.h>
> > > > +#include <linux/mfd/syscon.h>
> > > >  #include <linux/module.h>
> > > >  #include <linux/of.h>
> > > >  #include <linux/of_platform.h>
> > > >  #include <linux/phy/phy.h>
> > > >  #include <linux/platform_device.h>
> > > >  #include <linux/regmap.h>
> > > > +#include <dt-bindings/firmware/imx/rsrc.h>
> > > > +
> > > > +/* Control and Status Registers(CSR) */
> > > > +#define PHY_CTRL			0x00
> > > > +#define  CCM_MASK			GENMASK(7, 5)
> > > > +#define  CCM(n)				FIELD_PREP(CCM_MASK, (n))
> > > > +#define  CA_MASK			GENMASK(4, 2)
> > > > +#define  CA(n)				FIELD_PREP(CA_MASK, (n))
> > > > +#define  RFB				BIT(1)
> > > > +#define  LVDS_EN			BIT(0)
> > > >  
> > > >  /* DPHY registers */
> > > >  #define DPHY_PD_DPHY			0x00
> > > > @@ -55,8 +69,15 @@
> > > >  #define PWR_ON	0
> > > >  #define PWR_OFF	1
> > > >  
> > > > +#define MIN_VCO_FREQ 640000000
> > > > +#define MAX_VCO_FREQ 1500000000
> > > > +
> > > > +#define MIN_LVDS_REFCLK_FREQ 24000000
> > > > +#define MAX_LVDS_REFCLK_FREQ 150000000
> > > > +
> > > >  enum mixel_dphy_devtype {
> > > >  	MIXEL_IMX8MQ,
> > > > +	MIXEL_IMX8QXP,
> > > >  };
> > > >  
> > > >  struct mixel_dphy_devdata {
> > > > @@ -65,6 +86,7 @@ struct mixel_dphy_devdata {
> > > >  	u8 reg_rxlprp;
> > > >  	u8 reg_rxcdrp;
> > > >  	u8 reg_rxhs_settle;
> > > > +	bool is_combo;	/* MIPI DPHY and LVDS PHY combo */
> > > >  };
> > > >  
> > > >  static const struct mixel_dphy_devdata mixel_dphy_devdata[] = {
> > > > @@ -74,6 +96,10 @@ static const struct mixel_dphy_devdata mixel_dphy_devdata[] = {
> > > >  		.reg_rxlprp = 0x40,
> > > >  		.reg_rxcdrp = 0x44,
> > > >  		.reg_rxhs_settle = 0x48,
> > > > +		.is_combo = false,
> > > > +	},
> > > > +	[MIXEL_IMX8QXP] = {
> > > > +		.is_combo = true,
> > > >  	},
> > > >  };
> > > >  
> > > > @@ -95,8 +121,12 @@ struct mixel_dphy_cfg {
> > > >  struct mixel_dphy_priv {
> > > >  	struct mixel_dphy_cfg cfg;
> > > >  	struct regmap *regmap;
> > > > +	struct regmap *lvds_regmap;
> > > >  	struct clk *phy_ref_clk;
> > > >  	const struct mixel_dphy_devdata *devdata;
> > > > +	struct imx_sc_ipc *ipc_handle;
> > > > +	bool is_slave;
> > > > +	int id;
> > > >  };
> > > >  
> > > >  static const struct regmap_config mixel_dphy_regmap_config = {
> > > > @@ -317,7 +347,8 @@ static int mixel_dphy_set_pll_params(struct phy *phy)
> > > >  	return 0;
> > > >  }
> > > >  
> > > > -static int mixel_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
> > > > +static int
> > > > +mixel_dphy_configure_mipi_dphy(struct phy *phy, union phy_configure_opts *opts)
> > > >  {
> > > >  	struct mixel_dphy_priv *priv = phy_get_drvdata(phy);
> > > >  	struct mixel_dphy_cfg cfg = { 0 };
> > > > @@ -345,15 +376,118 @@ static int mixel_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
> > > >  	return 0;
> > > >  }
> > > >  
> > > > +static int
> > > > +mixel_dphy_configure_lvds_phy(struct phy *phy, union phy_configure_opts *opts)
> > > > +{
> > > > +	struct mixel_dphy_priv *priv = phy_get_drvdata(phy);
> > > > +	struct phy_configure_opts_lvds *lvds_opts = &opts->lvds;
> > > > +	unsigned long data_rate;
> > > > +	unsigned long fvco;
> > > > +	u32 rsc;
> > > > +	u32 co;
> > > > +	int ret;
> > > > +
> > > > +	priv->is_slave = lvds_opts->is_slave;
> > > > +
> > > > +	/* LVDS interface pins */
> > > > +	regmap_write(priv->lvds_regmap, PHY_CTRL, CCM(0x5) | CA(0x4) | RFB);
> > > > +
> > > > +	/* enable MODE8 only for slave LVDS PHY */
> > > > +	rsc = priv->id ? IMX_SC_R_MIPI_1 : IMX_SC_R_MIPI_0;
> > > > +	ret = imx_sc_misc_set_control(priv->ipc_handle, rsc, IMX_SC_C_DUAL_MODE,
> > > > +				      lvds_opts->is_slave);
> > > > +	if (ret) {
> > > > +		dev_err(&phy->dev, "Failed to configure MODE8: %d\n", ret);
> > > > +		return ret;
> > > > +	}
> > > > +
> > > > +	/*
> > > > +	 * Choose an appropriate divider ratio to meet the requirement of
> > > > +	 * PLL VCO frequency range.
> > > > +	 *
> > > > +	 *  -----  640MHz ~ 1500MHz   ------------      ---------------
> > > > +	 * | VCO | ----------------> | CO divider | -> | LVDS data rate|
> > > > +	 *  -----       FVCO          ------------      ---------------
> > > > +	 *                            1/2/4/8 div     7 * differential_clk_rate
> > > > +	 */
> > > > +	data_rate = 7 * lvds_opts->differential_clk_rate;
> > > > +	for (co = 1; co <= 8; co *= 2) {
> > > > +		fvco = data_rate * co;
> > > > +
> > > > +		if (fvco >= MIN_VCO_FREQ)
> > > > +			break;
> > > > +	}
> > > > +
> > > > +	if (fvco < MIN_VCO_FREQ || fvco > MAX_VCO_FREQ) {
> > > > +		dev_err(&phy->dev, "VCO frequency %lu is out of range\n", fvco);
> > > > +		return -ERANGE;
> > > > +	}
> > > > +
> > > > +	/*
> > > > +	 * CO is configurable, while CN and CM are not,
> > > > +	 * as fixed ratios 1 and 7 are applied respectively.
> > > > +	 */
> > > > +	phy_write(phy, __ffs(co), DPHY_CO);
> > > > +
> > > > +	/* set reference clock rate */
> > > > +	clk_set_rate(priv->phy_ref_clk, lvds_opts->differential_clk_rate);
> > > > +
> > > > +	return ret;
> > > > +}
> > > > +
> > > > +static int mixel_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
> > > > +{
> > > > +	if (phy->attrs.mode == PHY_MODE_MIPI_DPHY)
> > > > +		return mixel_dphy_configure_mipi_dphy(phy, opts);
> > > > +	else if (phy->attrs.mode == PHY_MODE_LVDS)
> > > > +		return mixel_dphy_configure_lvds_phy(phy, opts);
> > > > +
> > > > +	dev_err(&phy->dev, "Failed to configure PHY with invalid PHY mode\n");
> > > > +	return -EINVAL;
> > > > +}
> > > > +
> > > > +static int
> > > > +mixel_dphy_validate_lvds_phy(struct phy *phy, union phy_configure_opts *opts)
> > > > +{
> > > > +	struct phy_configure_opts_lvds *lvds_cfg = &opts->lvds;
> > > > +
> > > > +	if (lvds_cfg->bits_per_lane_and_dclk_cycle != 7) {
> > > > +		dev_err(&phy->dev, "Invalid bits per LVDS data lane: %u\n",
> > > > +					lvds_cfg->bits_per_lane_and_dclk_cycle);
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > > +	if (lvds_cfg->lanes != 4) {
> > > > +		dev_err(&phy->dev, "Invalid LVDS data lanes: %u\n",
> > > > +						lvds_cfg->lanes);
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > > +	if (lvds_cfg->differential_clk_rate < MIN_LVDS_REFCLK_FREQ ||
> > > > +	    lvds_cfg->differential_clk_rate > MAX_LVDS_REFCLK_FREQ) {
> > > > +		dev_err(&phy->dev,
> > > > +			"Invalid LVDS differential clock rate: %lu\n",
> > > > +					lvds_cfg->differential_clk_rate);
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > > +	return 0;
> > > > +}
> > > > +
> > > >  static int mixel_dphy_validate(struct phy *phy, enum phy_mode mode, int submode,
> > > >  			       union phy_configure_opts *opts)
> > > >  {
> > > > -	struct mixel_dphy_cfg cfg = { 0 };
> > > > +	if (mode == PHY_MODE_MIPI_DPHY) {
> > > > +		struct mixel_dphy_cfg mipi_dphy_cfg = { 0 };
> > > >  
> > > > -	if (mode != PHY_MODE_MIPI_DPHY)
> > > > -		return -EINVAL;
> > > > +		return mixel_dphy_config_from_opts(phy, &opts->mipi_dphy,
> > > > +							&mipi_dphy_cfg);
> > > > +	} else if (mode == PHY_MODE_LVDS) {
> > > > +		return mixel_dphy_validate_lvds_phy(phy, opts);
> > > > +	}
> > > >  
> > > > -	return mixel_dphy_config_from_opts(phy, &opts->mipi_dphy, &cfg);
> > > > +	dev_err(&phy->dev, "Failed to validate PHY with invalid PHY mode\n");
> > > 
> > > Can you print the `mode` here so it becomes obvious from the error what
> > > incorrect mode got passed in?
> > 
> > Will do in the next version.
> > 
> > > > +	return -EINVAL;
> > > >  }
> > > >  
> > > >  static int mixel_dphy_init(struct phy *phy)
> > > > @@ -373,27 +507,74 @@ static int mixel_dphy_exit(struct phy *phy)
> > > >  	return 0;
> > > >  }
> > > >  
> > > > -static int mixel_dphy_power_on(struct phy *phy)
> > > > +static int mixel_dphy_power_on_mipi_dphy(struct phy *phy)
> > > >  {
> > > >  	struct mixel_dphy_priv *priv = phy_get_drvdata(phy);
> > > >  	u32 locked;
> > > >  	int ret;
> > > >  
> > > > -	ret = clk_prepare_enable(priv->phy_ref_clk);
> > > > -	if (ret < 0)
> > > > -		return ret;
> > > > -
> > > >  	phy_write(phy, PWR_ON, DPHY_PD_PLL);
> > > >  	ret = regmap_read_poll_timeout(priv->regmap, DPHY_LOCK, locked,
> > > >  				       locked, PLL_LOCK_SLEEP,
> > > >  				       PLL_LOCK_TIMEOUT);
> > > >  	if (ret < 0) {
> > > >  		dev_err(&phy->dev, "Could not get DPHY lock (%d)!\n", ret);
> > > > -		goto clock_disable;
> > > > +		return ret;
> > > >  	}
> > > >  	phy_write(phy, PWR_ON, DPHY_PD_DPHY);
> > > >  
> > > >  	return 0;
> > > > +}
> > > > +
> > > > +static int mixel_dphy_power_on_lvds_phy(struct phy *phy)
> > > > +{
> > > > +	struct mixel_dphy_priv *priv = phy_get_drvdata(phy);
> > > > +	u32 locked;
> > > > +	int ret;
> > > > +
> > > > +	regmap_update_bits(priv->lvds_regmap, PHY_CTRL, LVDS_EN, LVDS_EN);
> > > > +
> > > > +	phy_write(phy, PWR_ON, DPHY_PD_DPHY);
> > > > +	phy_write(phy, PWR_ON, DPHY_PD_PLL);
> > > > +
> > > > +	/* do not wait for slave LVDS PHY being locked */
> > > > +	if (priv->is_slave)
> > > > +		return 0;
> > > > +
> > > > +	ret = regmap_read_poll_timeout(priv->regmap, DPHY_LOCK, locked,
> > > > +				       locked, PLL_LOCK_SLEEP,
> > > > +				       PLL_LOCK_TIMEOUT);
> > > > +	if (ret < 0) {
> > > > +		dev_err(&phy->dev, "Could not get LVDS PHY lock (%d)!\n", ret);
> > > > +		return ret;
> > > > +	}
> > > > +
> > > > +	return 0;
> > > > +}
> > > > +
> > > > +static int mixel_dphy_power_on(struct phy *phy)
> > > > +{
> > > > +	struct mixel_dphy_priv *priv = phy_get_drvdata(phy);
> > > > +	int ret;
> > > > +
> > > > +	ret = clk_prepare_enable(priv->phy_ref_clk);
> > > > +	if (ret < 0)
> > > > +		return ret;
> > > > +
> > > > +	if (phy->attrs.mode == PHY_MODE_MIPI_DPHY) {
> > > > +		ret = mixel_dphy_power_on_mipi_dphy(phy);
> > > > +	} else if (phy->attrs.mode == PHY_MODE_LVDS) {
> > > > +		ret = mixel_dphy_power_on_lvds_phy(phy);
> > > > +	} else {
> > > > +		dev_err(&phy->dev,
> > > > +			"Failed to power on PHY with invalid PHY mode\n");
> > > 
> > > Can you print the `mode` here so it becomes obvious from the error what
> > > incorrect mode got passed in?
> > 
> > Will do in the next version.
> > 
> > > > +		ret = -EINVAL;
> > > > +	}
> > > > +
> > > > +	if (ret)
> > > > +		goto clock_disable;
> > > > +
> > > > +	return 0;
> > > >  clock_disable:
> > > >  	clk_disable_unprepare(priv->phy_ref_clk);
> > > >  	return ret;
> > > > @@ -406,16 +587,52 @@ static int mixel_dphy_power_off(struct phy *phy)
> > > >  	phy_write(phy, PWR_OFF, DPHY_PD_PLL);
> > > >  	phy_write(phy, PWR_OFF, DPHY_PD_DPHY);
> > > >  
> > > > +	if (phy->attrs.mode == PHY_MODE_LVDS)
> > > > +		regmap_update_bits(priv->lvds_regmap, PHY_CTRL, LVDS_EN, 0);
> > > > +
> > > >  	clk_disable_unprepare(priv->phy_ref_clk);
> > > >  
> > > >  	return 0;
> > > >  }
> > > >  
> > > > +static int mixel_dphy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
> > > > +{
> > > > +	struct mixel_dphy_priv *priv = phy_get_drvdata(phy);
> > > > +	int ret;
> > > > +
> > > 
> > > I'd reject all modes except PHY_MODE_MIPI_DPHY and PHY_MODE_MIPI_LVDS upfront...
> > 
> > It seems that this overall rejection would cause _double_ check
> > together with the snippet right below, which should be avoided.
> > 
> > > > +	/* Currently, MIPI DPHY mode only, if it's not a combo PHY. */
> > > > +	if (!priv->devdata->is_combo && mode != PHY_MODE_MIPI_DPHY) {
> > > > +		dev_err(&phy->dev, "Failed to set PHY mode to MIPI DPHY\n");
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > > +	if (priv->devdata->is_combo && mode != PHY_MODE_LVDS) {
> > > > +		dev_err(&phy->dev, "Failed to set PHY mode for combo PHY\n");
> > > > +		return -EINVAL;
> > > > +	}
> > > 
> > > ...and then just reject on whetehr `is_combo` is set or not. This makes
> > > it easier to add more later.
> > 
> > The above snippet is rejecting on whether 'is_combo' is set or not.
> > So, in short, the current implementation looks ok to me.
> > Or, things still can be improved here?
> 
> I agree, i think what tripped me up is that the double negative check
> comes first comined with the comment so i'd just drop the comment and
> start with the positive one:
> 
> 	if (priv->devdata->is_combo && mode != PHY_MODE_LVDS) {
> 		dev_err(&phy->dev, "Failed to set PHY mode for combo PHY\n");
> 		return -EINVAL;
> 	}
> 
> 	if (!priv->devdata->is_combo && mode != PHY_MODE_MIPI_DPHY) {
> 		dev_err(&phy->dev, "Failed to set PHY mode to MIPI DPHY\n");
> 		return -EINVAL;
> 	}

Ok.  I'll use this snippet.

Thanks,
Liu Ying

> 
> Cheers,
>  -- Guido
> 
> > Thanks,
> > Liu Ying
> > 
> > > > +	if (priv->devdata->is_combo) {
> > > > +		u32 rsc = priv->id ? IMX_SC_R_MIPI_1 : IMX_SC_R_MIPI_0;
> > > > +
> > > > +		ret = imx_sc_misc_set_control(priv->ipc_handle,
> > > > +					      rsc, IMX_SC_C_MODE,
> > > > +					      mode == PHY_MODE_LVDS);
> > > > +		if (ret) {
> > > > +			dev_err(&phy->dev,
> > > > +				"Failed to set PHY mode via SCU ipc: %d\n", ret);
> > > > +			return ret;
> > > > +		}
> > > > +	}
> > > > +
> > > > +	return 0;
> > > > +}
> > > > +
> > > >  static const struct phy_ops mixel_dphy_phy_ops = {
> > > >  	.init = mixel_dphy_init,
> > > >  	.exit = mixel_dphy_exit,
> > > >  	.power_on = mixel_dphy_power_on,
> > > >  	.power_off = mixel_dphy_power_off,
> > > > +	.set_mode = mixel_dphy_set_mode,
> > > >  	.configure = mixel_dphy_configure,
> > > >  	.validate = mixel_dphy_validate,
> > > >  	.owner = THIS_MODULE,
> > > > @@ -424,6 +641,8 @@ static const struct phy_ops mixel_dphy_phy_ops = {
> > > >  static const struct of_device_id mixel_dphy_of_match[] = {
> > > >  	{ .compatible = "fsl,imx8mq-mipi-dphy",
> > > >  	  .data = &mixel_dphy_devdata[MIXEL_IMX8MQ] },
> > > > +	{ .compatible = "fsl,imx8qxp-mipi-dphy",
> > > > +	  .data = &mixel_dphy_devdata[MIXEL_IMX8QXP] },
> > > >  	{ /* sentinel */ },
> > > >  };
> > > >  MODULE_DEVICE_TABLE(of, mixel_dphy_of_match);
> > > > @@ -436,6 +655,7 @@ static int mixel_dphy_probe(struct platform_device *pdev)
> > > >  	struct mixel_dphy_priv *priv;
> > > >  	struct phy *phy;
> > > >  	void __iomem *base;
> > > > +	int ret;
> > > >  
> > > >  	if (!np)
> > > >  		return -ENODEV;
> > > > @@ -467,6 +687,30 @@ static int mixel_dphy_probe(struct platform_device *pdev)
> > > >  	dev_dbg(dev, "phy_ref clock rate: %lu\n",
> > > >  		clk_get_rate(priv->phy_ref_clk));
> > > >  
> > > > +	if (priv->devdata->is_combo) {
> > > > +		priv->lvds_regmap =
> > > > +			syscon_regmap_lookup_by_phandle(np, "fsl,syscon");
> > > > +		if (IS_ERR(priv->lvds_regmap)) {
> > > > +			ret = PTR_ERR(priv->lvds_regmap);
> > > > +			dev_err_probe(dev, ret, "Failed to get LVDS regmap\n");
> > > > +			return ret;
> > > > +		}
> > > > +
> > > > +		priv->id = of_alias_get_id(np, "mipi_dphy");
> > > > +		if (priv->id < 0) {
> > > > +			dev_err(dev, "Failed to get phy node alias id: %d\n",
> > > > +								 priv->id);
> > > > +			return priv->id;
> > > > +		}
> > > > +
> > > > +		ret = imx_scu_get_handle(&priv->ipc_handle);
> > > > +		if (ret) {
> > > > +			dev_err_probe(dev, ret,
> > > > +				      "Failed to get SCU ipc handle\n");
> > > > +			return ret;
> > > > +		}
> > > > +	}
> > > > +
> > > >  	dev_set_drvdata(dev, priv);
> > > >  
> > > >  	phy = devm_phy_create(dev, np, &mixel_dphy_phy_ops);
> > > > -- 
> > > > 2.7.4
> > > > 
> > > 
> > > Cheers,
> > >  -- Guido