Re: [PATCHv2 3/3] arm: dts: add bandgap entry for OMAP4460 devices

[Eduardo Valentin <eduardo.valentin@ti.com>]

[-- Attachment #1.1: Type: text/plain, Size: 2826 bytes --]

On 16-05-2013 03:20, Benoit Cousson wrote:
> Hi Eduardo,
> 
> On 05/15/2013 06:36 PM, Eduardo Valentin wrote:
>> On 15-05-2013 11:23, Benoit Cousson wrote:
>>> Hi Eduardo,
>>>
>>> On 05/15/2013 04:58 PM, Eduardo Valentin wrote:
>>>> Include bandgap devices for OMAP4460 devices.
>>>>
>>>> Cc: "Benoît Cousson" <b-cousson@ti.com>
>>>> Cc: Tony Lindgren <tony@atomide.com>
>>>> Cc: Russell King <linux@arm.linux.org.uk>
>>>> Cc: linux-omap@vger.kernel.org
>>>> Cc: devicetree-discuss@lists.ozlabs.org
>>>> Cc: linux-arm-kernel@lists.infradead.org
>>>> Cc: linux-kernel@vger.kernel.org
>>>> Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
>>>> ---
>>>>  arch/arm/boot/dts/omap4460.dtsi | 9 +++++++++
>>>>  1 file changed, 9 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi
>>>> index 2cf227c..e5bfbfe 100644
>>>> --- a/arch/arm/boot/dts/omap4460.dtsi
>>>> +++ b/arch/arm/boot/dts/omap4460.dtsi
>>>> @@ -29,4 +29,13 @@
>>>>  			     <0 55 0x4>;
>>>>  		ti,hwmods = "debugss";
>>>>  	};
>>>> +
>>>> +	bandgap {
>>>> +		reg = <0x4a002260 0x4
>>>> +			0x4a00232C 0x4
>>>> +			0x4a002378 0x18>;
>>>> +		compatible = "ti,omap4460-bandgap";
>>>> +		interrupts = <0 126 4>; /* talert */
>>>> +		ti,tshut-gpio = <86>;
>>
>>
>>
>>>
>>> Why do you need a custom attribute for GPIO? Cannot you use the standard
>>> one?
>>
>> I believe it was by your suggestion :-), during the first attempts to
>> send this driver. But could not find the thread link :-( sorry.
> 
> Ooops :-) I do not remember that... maybe it was long time ago, before
> we had any decent binding available for GPIO and IRQ...
> 


Probably it was because by that time we didnt have GPIO binding ready, yeah.

>> I guess the reasoning to mark it as a ti specific is because it will be
>> used as IRQ line to treat thermal shutdown (in SW).
> 
> Mmm, ok, so in that case, it is not even a gpio, but an interrupt entry
> that is needed like that:
> 
> 	interrupt-parent = <&gpio3>;
> 	interrupts = <22>; /* gpio line 86 */
> 
> Except that we already have an IRQ line connected to GIC for the
> Talert... I'm not sure we can have 2 different IRQ controllers for one
> device :-(
> 
> We need to check.
> 


Yeah, I also dont think this will work, because we will reparent the
interrupt, setting to a different controller. That will break the TALERT
signal already defined at GIC (check original patch).

I propose keeping the way I sent. Unless there is a way to set two
different controllers to same device.

> Regards,
> Benoit
> 
> 
>>> Where is the gpio controller phandle?
>>>
>>> Usually it looks like this:
>>>
>>> 	gpios = <&gpio1 8 0>;
>>>
>>>
>>> Regards,
>>> Benoit
>>>
>>>
>>>
>>
>>
> 
> 
> 



[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 295 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel