From mboxrd@z Thu Jan 1 00:00:00 1970 From: Dan Murphy Subject: Re: [PATCH v8] ARM: dts: omap4-panda: Update the LED support for the panda DTS Date: Fri, 31 May 2013 10:19:44 -0500 Message-ID: <51A8BF90.4060509@ti.com> References: <1370011682-20675-1-git-send-email-dmurphy@ti.com> Mime-Version: 1.0 Content-Type: text/plain; charset="UTF-8" Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: Sender: linux-kernel-owner@vger.kernel.org To: Javier Martinez Canillas Cc: b-cousson@ti.com, tony@atomide.com, linux@arm.linux.org.uk, devicetree-discuss@lists.ozlabs.org, linux-omap@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org List-Id: devicetree@vger.kernel.org On 05/31/2013 10:05 AM, Javier Martinez Canillas wrote: > On Fri, May 31, 2013 at 4:48 PM, Dan Murphy wrote: >> The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es >> are different. >> >> A1-A3 = gpio_wk7 >> ES = gpio_110 >> >> There is no change to LED D2 >> >> Abstract away the pinmux and the LED definitions for the two boards into >> the respective DTS files. >> >> Signed-off-by: Dan Murphy >> --- >> v8 - Rebase to latest and use pinctrl macros - https://patchwork.kernel.org/patch/2629351/ >> v7 - Update headline to add spaces - https://patchwork.kernel.org/patch/2583661/ >> v6 - Review comments updated - https://patchwork.kernel.org/patch/2582771/ >> v5 - Provide pincrtl phandle to the gpio-led driver - https://patchwork.kernel.org/patch/2573981/ >> >> arch/arm/boot/dts/omap4-panda-common.dtsi | 16 +++++++++++++++- >> arch/arm/boot/dts/omap4-panda-es.dts | 28 ++++++++++++++++++++++++++++ >> 2 files changed, 43 insertions(+), 1 deletions(-) >> >> diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi >> index d5d144a..523a800 100644 >> --- a/arch/arm/boot/dts/omap4-panda-common.dtsi >> +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi >> @@ -16,8 +16,13 @@ >> reg = <0x80000000 0x40000000>; /* 1 GB */ >> }; >> >> - leds { >> + leds: leds { >> compatible = "gpio-leds"; >> + pinctrl-names = "default"; >> + pinctrl-0 = < >> + &led_wkgpio_pins >> + >; >> + >> heartbeat { >> label = "pandaboard::status1"; >> gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; >> @@ -157,6 +162,15 @@ >> }; >> }; >> >> +&omap4_pmx_wkup { >> + led_wkgpio_pins: pinmux_leds_wkpins { >> + pinctrl-single,pins = < >> + 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 OUTPUT | MODE 3 */ >> + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 OUTPUT | MODE 3 */ > Hello Dan, > > The OUTPUT | MODE 3 in the comments were added so people shouldn't > have to look at the TRM to find what each constant number meant. But > now using the macros this is not needed anymore, so I don't think is > necessary to keep that on the comments. > > Best regards, > Javier Yes you are correct sending update to remove the comments -- ------------------ Dan Murphy