From: Grygorii Strashko <grygorii.strashko@ti.com>
To: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@linaro.org>,
linux-arm-kernel@lists.infradead.org, linux-omap@vger.kernel.org,
linux-kernel@vger.kernel.org,
devicetree-discuss@lists.ozlabs.org,
Benoit Cousson <benoit.cousson@linaro.org>,
Linus Walleij <linus.walleij@linaro.org>,
Stephen Warren <swarren@wwwdotorg.org>
Subject: Re: [PATCH 3/3] ARM: dts: omap4-sdp: add dynamic pin states for uart3/4
Date: Wed, 17 Jul 2013 19:41:29 +0300 [thread overview]
Message-ID: <51E6C939.40208@ti.com> (raw)
In-Reply-To: <20130717153248.GI7656@atomide.com>
Hi,
On 07/17/2013 06:32 PM, Tony Lindgren wrote:
> * Grygorii Strashko <grygorii.strashko@ti.com> [130717 04:49]:
>> Add dynamic "active"/"idle" pin states for uart3/4 which will be applied
>> when uart3/4 state is switched from active to idle and back by Runtime
>> PM or during system suspend.
>
> This is good for testing code, but should not be merged because
> omap4 has the iopad wake-ups available for uarts. So those can
> be always enabled.
In this case, 2 IRQ will be received per each UART RX event - one from
PRCM and from UART - and that's not good from PM perspective (It will
affect on CPUIdle and CPUFreq at least).
-- log when wake-up enabled always
106: 729 0 GIC 106 OMAP UART2
115: 13 0 GIC 115 mmc0
118: 68 0 GIC 118 mmc1
151: 0 0 GIC 151 twl6040
361: 322 0 PRCM hwmod_io
^^^^
-- log when wake-up enabled only when UART3 (console) is active
106: 1104 0 GIC 106 OMAP UART2
115: 13 0 GIC 115 mmc0
118: 68 0 GIC 118 mmc1
151: 0 0 GIC 151 twl6040
361: 7 0 PRCM hwmod_io
The same is valid for all devices which will leave WAKEUP_EN set
all the time (
>
>> --- a/arch/arm/boot/dts/omap4-sdp.dts
>> +++ b/arch/arm/boot/dts/omap4-sdp.dts
>> @@ -181,18 +181,40 @@
>> pinctrl-single,pins = <
>> 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */
>> 0x102 (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */
>> - 0x104 (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
>> 0x106 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>> >;
>> };
>
> This just need to become:
> pinctrl-single,pins = <
> ...
> 0x104 (WAKEUP_EN | PIN_INPUT_MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
> ...
> >;
> interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> };
>
> And so on. For am33xx you need to remux things to GPIO for the wake-up
> events, so you should maybe test on that instead.
>
> Regards,
>
> Tony
>
Regards,
- grygorii
next prev parent reply other threads:[~2013-07-17 16:41 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-17 11:41 [PATCH 0/3] ARM: OMAP2+: omap_device: add dynamic pinctrl handling Grygorii Strashko
2013-07-17 11:41 ` [PATCH 1/3] pinctrl: rollback check for !dev->pins in pinctrl_pm_select*() APIs Grygorii Strashko
2013-07-17 15:40 ` Tony Lindgren
2013-07-26 23:22 ` Linus Walleij
2013-07-17 11:41 ` [PATCH 2/3] ARM: OMAP2+: omap_device: add pinctrl handling Grygorii Strashko
2013-07-17 15:38 ` Tony Lindgren
2013-07-17 16:56 ` Grygorii Strashko
2013-07-18 8:14 ` Tony Lindgren
2013-07-18 11:22 ` Grygorii Strashko
2013-07-17 11:41 ` [PATCH 3/3] ARM: dts: omap4-sdp: add dynamic pin states for uart3/4 Grygorii Strashko
[not found] ` <1374061312-25469-4-git-send-email-grygorii.strashko-l0cyMroinI0@public.gmane.org>
2013-07-17 15:32 ` Tony Lindgren
2013-07-17 16:41 ` Grygorii Strashko [this message]
[not found] ` <51E6C939.40208-l0cyMroinI0@public.gmane.org>
2013-07-18 8:09 ` Tony Lindgren
2013-07-18 8:54 ` Grygorii Strashko
2013-07-18 9:04 ` Tony Lindgren
2013-07-18 12:01 ` Grygorii Strashko
2013-07-17 11:57 ` [PATCH 0/3] ARM: OMAP2+: omap_device: add dynamic pinctrl handling Roger Quadros
2013-07-17 12:30 ` Grygorii Strashko
2013-07-18 6:44 ` Roger Quadros
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=51E6C939.40208@ti.com \
--to=grygorii.strashko@ti.com \
--cc=benoit.cousson@linaro.org \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=khilman@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=swarren@wwwdotorg.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).