From: Josua Mayer <josua@solid-run.com>
To: Shawn Guo <shawnguo@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Frank Li <frank.li@nxp.com>,
Carlos Song <carlos.song@nxp.com>
Cc: Jon Nettleton <jon@solid-run.com>,
Rabeeh Khoury <rabeeh@solid-run.com>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux@ew.tq-group.com" <linux@ew.tq-group.com>,
"stable@vger.kernel.org" <stable@vger.kernel.org>
Subject: Re: [PATCH] arm64: dts: fsl-lx2160a: define pinctrl for iic2 sd-cd/-wp functions
Date: Sun, 13 Jul 2025 08:24:48 +0000 [thread overview]
Message-ID: <524f940e-9e31-411c-a419-cfb5a48d55ea@solid-run.com> (raw)
In-Reply-To: <f32c5525-3162-4acd-880c-99fc46d3a63d@solid-run.com>
On 10/07/2025 18:09, Josua Mayer wrote:
> LX2160 SoC uses a densely packed configuration area in memory for pin
> muxing - configuring a variable number of IOs at a time.
>
> Since pinctrl nodes were added for the i2c signals of LX2160 SoC, boot
> errors have been observed on SolidRun LX2162A Clearfog board when rootfs
> is located on SD-Card (esdhc0):
>
> [ 1.961035] mmc0: new ultra high speed SDR104 SDHC card at address aaaa
> ...
> [ 5.220655] i2c i2c-1: using pinctrl states for GPIO recovery
> [ 5.226425] i2c i2c-1: using generic GPIOs for recovery
> ...
> [ 5.440471] mmc0: card aaaa removed
>
> The card-detect and write-protect signals of esdhc0 are an alternate
> function of IIC2 (in dts i2c1 - on lx2162 clearfog status disabled).
>
> By use of u-boot "md", and linux "devmem" command it was confirmed that
> RCWSR12 (at 0x01e0012c) with IIC2_PMUX (at bits 0-2) changes from
> 0x08000006 to 0x0000000 after starting Linux.
compared values at 0x01e0012c (read-only) and 0x70010012c (dcfg).
> This means that the card-detect pin function has changed to i2c function
> - which will cause the controller to detect card removal.
>
> The respective i2c1-scl-pins node is only linked to i2c1 node that has
> status disabled in device-tree for the solidrun boards.
> How the memory is changed has not been investigated.
RCWSR12 at 0x01e0012c is read-only and reflects the initial boot-time
setting from RCW stage. The pinctrl-single driver uses dynamic
configuration area at 0x70010012c to overide boot-time values.
We found that the dynamic configuration address reads 0 before first
write, hence when applying the first configuration the original non-zero
value is lost.
It might be worth reviewing and defining pinctrl for all alternate functions
of each i2c controller.
> As a workaround add a new pinctrl definition for the
> card-detect/write-protect function of IIC2 pins.
> It seems unwise to link this directly from the SoC dtsi as boards may
> rely on other functions such as flextimer.
>
> Instead add the pinctrl to each board's esdhc0 node if it is known to
> rely on native card-detect function. These boards have esdhc0 node
> enabled and do not define broken-cd property:
>
> - fsl-lx2160a-bluebox3.dts
> - fsl-lx2160a-clearfog-itx.dtsi
> - fsl-lx2160a-qds.dts
> - fsl-lx2160a-rdb.dts
> - fsl-lx2160a-tqmlx2160a-mblx2160a.dts
> - fsl-lx2162a-clearfog.dts
> - fsl-lx2162a-qds.dts
>
> This was tested on the SolidRun LX2162 Clearfog with Linux v6.12.33.
>
> Fixes: 8a1365c7bbc1 ("arm64: dts: lx2160a: add pinmux and i2c gpio to
> support bus recovery")
> Cc: stable@vger.kernel.org
> Signed-off-by: Josua Mayer <josua@solid-run.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts | 2 ++
> arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi | 2 ++
> arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts | 2 ++
> arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 2 ++
> arch/arm64/boot/dts/freescale/fsl-lx2160a-tqmlx2160a-mblx2160a.dts | 2 ++
> arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 4
> ++++
> arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts | 2 ++
> arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts | 2 ++
> 8 files changed, 18 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> index 042c486bdda2..298fcdce6c6b 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> @@ -152,6 +152,8 @@ &esdhc0 {
> sd-uhs-sdr50;
> sd-uhs-sdr25;
> sd-uhs-sdr12;
> + pinctrl-0 = <&i2c1_sdhc_cdwp>;
> + pinctrl-names = "default";
> status = "okay";
> };
> diff --git
> a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
> index a7dcbecc1f41..67ffe2e1b0bc 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
> @@ -93,6 +93,8 @@ &esdhc0 {
> sd-uhs-sdr50;
> sd-uhs-sdr25;
> sd-uhs-sdr12;
> + pinctrl-0 = <&i2c1_sdhc_cdwp>;
> + pinctrl-names = "default";
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> index 4d721197d837..17fe4a8fd35e 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
> @@ -214,6 +214,8 @@ &emdio2 {
> };
> &esdhc0 {
> + pinctrl-0 = <&i2c1_sdhc_cdwp>;
> + pinctrl-names = "default";
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
> b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
> index 0c44b3cbef77..faa486d6a5b1 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
> @@ -131,6 +131,8 @@ &esdhc0 {
> sd-uhs-sdr50;
> sd-uhs-sdr25;
> sd-uhs-sdr12;
> + pinctrl-0 = <&i2c1_sdhc_cdwp>;
> + pinctrl-names = "default";
> status = "okay";
> };
> diff --git
> a/arch/arm64/boot/dts/freescale/fsl-lx2160a-tqmlx2160a-mblx2160a.dts
> b/arch/arm64/boot/dts/freescale/fsl-lx2160a-tqmlx2160a-mblx2160a.dts
> index f6a4f8d54301..4ba55feb18b2 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-tqmlx2160a-mblx2160a.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-tqmlx2160a-mblx2160a.dts
> @@ -177,6 +177,8 @@ &esdhc0 {
> no-sdio;
> wp-gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
> cd-gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&i2c1_scl_gpio>;
> + pinctrl-names = "default";
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> index c9541403bcd8..555a191b0bb4 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> @@ -1717,6 +1717,10 @@ i2c1_scl_gpio: i2c1-scl-gpio-pins {
> pinctrl-single,bits = <0x0 0x1 0x7>;
> };
> + i2c1_sdhc_cdwp: i2c1-esdhc0-cd-wp-pins {
> + pinctrl-single,bits = <0x0 0x6 0x7>;
> + };
> +
> i2c2_scl: i2c2-scl-pins {
> pinctrl-single,bits = <0x0 0 (0x7 << 3)>;
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> b/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> index eafef8718a0f..4b58105c3ffa 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> @@ -227,6 +227,8 @@ &esdhc0 {
> sd-uhs-sdr50;
> sd-uhs-sdr25;
> sd-uhs-sdr12;
> + pinctrl-0 = <&i2c1_sdhc_cdwp>;
> + pinctrl-names = "default";
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
> b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
> index 9f5ff1ffe7d5..caa079df35f6 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
> @@ -238,6 +238,8 @@ &esdhc0 {
> sd-uhs-sdr50;
> sd-uhs-sdr25;
> sd-uhs-sdr12;
> + pinctrl-0 = <&i2c1_sdhc_cdwp>;
> + pinctrl-names = "default";
> status = "okay";
> };
>
> ---
> base-commit: 19272b37aa4f83ca52bdf9c16d5d81bdd1354494
> change-id: 20250710-lx2160-sd-cd-00bf38ae169e
>
> Best regards,
next prev parent reply other threads:[~2025-07-13 8:25 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-07-10 15:09 [PATCH] arm64: dts: fsl-lx2160a: define pinctrl for iic2 sd-cd/-wp functions Josua Mayer
2025-07-13 8:24 ` Josua Mayer [this message]
2025-07-13 9:17 ` Josua Mayer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=524f940e-9e31-411c-a419-cfb5a48d55ea@solid-run.com \
--to=josua@solid-run.com \
--cc=carlos.song@nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=frank.li@nxp.com \
--cc=jon@solid-run.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@ew.tq-group.com \
--cc=rabeeh@solid-run.com \
--cc=robh@kernel.org \
--cc=shawnguo@kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).