devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Benoit Cousson <bcousson@baylibre.com>
To: Rajendra Nayak <rnayak@ti.com>
Cc: paul@pwsan.com, tony@atomide.com, linux-omap@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-doc@vger.kernel.org, Mark Rutland <mark.rutland@arm.com>,
	"rob.herring@calxeda.com" <rob.herring@calxeda.com>
Subject: Re: [PATCH v2 2/5] ARM: dts: omap: Add new bindings for OMAP
Date: Wed, 09 Oct 2013 18:45:54 +0200	[thread overview]
Message-ID: <52558842.6040409@baylibre.com> (raw)
In-Reply-To: <5255872A.30702@ti.com>

+ A couple of DT maintainers

On 09/10/2013 18:41, Rajendra Nayak wrote:
> On Wednesday 09 October 2013 08:43 PM, Benoit Cousson wrote:
>> Hi Rajendra,
>>
>> On 09/10/2013 12:11, Rajendra Nayak wrote:
>>> On OMAP we have co-processor IPs, memory controllers,
>>> GPIOs which control regulators and power switches to
>>> PMIC, and SoC internal Bus IPs, some or most of which
>>> should either not be reset or idled or both at init.
>>> (In some cases there are erratas which prevent an IP
>>> from being reset)
>>> Have a way to pass this information from DT.
>>
>> Did you get some acked-by from the DT maintainers?
>> Every new bindings must be carefully reviewed now.
>
> Nope, I haven't. The patches are on the list for a couple
> of months now.

Let's see if Mark and Rob are OK with that.

Thanks,
Benoit

>
>>
>> Regards,
>> Benoit
>>
>>>
>>> Update the am33xx/omap4 and omap5 dtsi files with the
>>> new bindings for modules which either should not be
>>> idled. reset or both. A later patch would cleanup the
>>> same information that exists today as part of the hwmod
>>> data files.
>>>
>>> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
>>> ---
>>>    .../devicetree/bindings/arm/omap/omap.txt          |    3 ++-
>>>    arch/arm/boot/dts/am33xx.dtsi                      |    2 ++
>>>    arch/arm/boot/dts/omap4.dtsi                       |    3 +++
>>>    arch/arm/boot/dts/omap5.dtsi                       |    2 ++
>>>    4 files changed, 9 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
>>> index 91b7049..808c154 100644
>>> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
>>> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
>>> @@ -21,7 +21,8 @@ Required properties:
>>>    Optional properties:
>>>    - ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
>>>      during suspend.
>>> -
>>> +- ti,no-reset-on-init: When present, the module should not be reset at init
>>> +- ti,no-idle-on-init: When present, the module should not be idled at init
>>>
>>>    Example:
>>>
>>> diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
>>> index f9c5da9..ec33ea0 100644
>>> --- a/arch/arm/boot/dts/am33xx.dtsi
>>> +++ b/arch/arm/boot/dts/am33xx.dtsi
>>> @@ -607,6 +607,7 @@
>>>                reg = <0x44d00000 0x4000    /* M3 UMEM */
>>>                       0x44d80000 0x2000>;    /* M3 DMEM */
>>>                ti,hwmods = "wkup_m3";
>>> +            ti,no-reset-on-init;
>>>            };
>>>
>>>            elm: elm@48080000 {
>>> @@ -637,6 +638,7 @@
>>>            gpmc: gpmc@50000000 {
>>>                compatible = "ti,am3352-gpmc";
>>>                ti,hwmods = "gpmc";
>>> +            ti,no-idle-on-init;
>>>                reg = <0x50000000 0x2000>;
>>>                interrupts = <100>;
>>>                gpmc,num-cs = <7>;
>>> diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
>>> index 22d9f2b..e8fe797 100644
>>> --- a/arch/arm/boot/dts/omap4.dtsi
>>> +++ b/arch/arm/boot/dts/omap4.dtsi
>>> @@ -214,6 +214,7 @@
>>>                gpmc,num-cs = <8>;
>>>                gpmc,num-waitpins = <4>;
>>>                ti,hwmods = "gpmc";
>>> +            ti,no-idle-on-init;
>>>            };
>>>
>>>            uart1: serial@4806a000 {
>>> @@ -492,6 +493,7 @@
>>>                reg = <0x4c000000 0x100>;
>>>                interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
>>>                ti,hwmods = "emif1";
>>> +            ti,no-idle-on-init;
>>>                phy-type = <1>;
>>>                hw-caps-read-idle-ctrl;
>>>                hw-caps-ll-interface;
>>> @@ -503,6 +505,7 @@
>>>                reg = <0x4d000000 0x100>;
>>>                interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
>>>                ti,hwmods = "emif2";
>>> +            ti,no-idle-on-init;
>>>                phy-type = <1>;
>>>                hw-caps-read-idle-ctrl;
>>>                hw-caps-ll-interface;
>>> diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
>>> index 7cdea1b..a9d49df 100644
>>> --- a/arch/arm/boot/dts/omap5.dtsi
>>> +++ b/arch/arm/boot/dts/omap5.dtsi
>>> @@ -607,6 +607,7 @@
>>>            emif1: emif@0x4c000000 {
>>>                compatible    = "ti,emif-4d5";
>>>                ti,hwmods    = "emif1";
>>> +            ti,no-idle-on-init;
>>>                phy-type    = <2>; /* DDR PHY type: Intelli PHY */
>>>                reg = <0x4c000000 0x400>;
>>>                interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
>>> @@ -618,6 +619,7 @@
>>>            emif2: emif@0x4d000000 {
>>>                compatible    = "ti,emif-4d5";
>>>                ti,hwmods    = "emif2";
>>> +            ti,no-idle-on-init;
>>>                phy-type    = <2>; /* DDR PHY type: Intelli PHY */
>>>                reg = <0x4d000000 0x400>;
>>>                interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
>>>
>>
>


  reply	other threads:[~2013-10-09 16:45 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-10-09 10:11 [PATCH v2 0/5] OMAP: Add DT bindings to specify when devices should not be idled or reset Rajendra Nayak
2013-10-09 10:11 ` [PATCH v2 1/5] ARM: OMAP2+: hwmod: cleanup HWMOD_INIT_NO_RESET usage Rajendra Nayak
2013-10-09 14:55   ` Paul Walmsley
2013-10-09 10:11 ` [PATCH v2 2/5] ARM: dts: omap: Add new bindings for OMAP Rajendra Nayak
2013-10-09 15:13   ` Benoit Cousson
2013-10-09 16:41     ` Rajendra Nayak
2013-10-09 16:45       ` Benoit Cousson [this message]
2013-10-15  7:27         ` Benoit Cousson
2013-10-15  8:23           ` Rajendra Nayak
2013-10-09 10:11 ` [PATCH v2 3/5] ARM: OMAP2+: hwmod: Extract no-idle and no-reset info from DT Rajendra Nayak
2013-10-09 14:55   ` Paul Walmsley
2013-10-09 10:12 ` [PATCH v2 4/5] ARM: OMAP2+: hwmod: Cleanup usage of HWMOD_INIT_NO_RESET and HWMOD_INIT_NO_IDLE Rajendra Nayak
2013-10-09 10:12 ` [PATCH v2 5/5] ARM: dts: AM335x-evmsk: Do not reset gpio0 Rajendra Nayak
2013-10-10 16:44 ` [PATCH] ARM: dts: omap4-panda-es: Do not reset gpio1 Nishanth Menon
2013-10-10 16:47   ` Tony Lindgren
2013-10-10 19:01     ` Nishanth Menon
2013-10-15  7:28   ` Benoit Cousson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=52558842.6040409@baylibre.com \
    --to=bcousson@baylibre.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=paul@pwsan.com \
    --cc=rnayak@ti.com \
    --cc=rob.herring@calxeda.com \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).